Structural Engineering Commons^™

Development Of Cost-Effective, Energy Efficient Steel Framing: Thermal Performance Of Slit-Web Steel Wall Studs, Roger A. Laboube

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Development Of Cost-Effective, Energy Efficient Steel Framing: Structural Performance Of Slit-Web Steel Wall Studs, Roger A. Laboube

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Seismic Retrofit Of Ciss Pile Bent Cap Connections, Michael C. Lubiewski, Pedro Franco Silva, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Three 4/5-scale units were cast, retrofitted, and tested under simulated seismic loads. These units were built to model a bridge bent consisting of a cast in place steel shell (CISS) column foundation shaft and a bent cap configured to form a tee connection. Each unit was retrofitted in the column, bent cap, and their connection according to current seismic design standards. The main objective was to ensuring ductile performance under lateral loads.

Specific seismic improvements made to the column and the bent cap system were: (1) the moment capacity of the column was reduced by cutting a portion of the …

Investigation Of Cause Of Cracked Stringer On The Blanchette Bridge, Ward Marianos Jr., Genda Chen, Nestore Galati, Fabio Matta

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Blanchette Bridge carries Interstate 70 across the Missouri River, connecting St. Louis and St. Charles counties in eastern Missouri. The westbound bridge was constructed in 1958. In 1979, the original reinforced concrete roadway deck on the bridge was replaced with a steel grid deck system, welded to supporting girders and stringers. In 1999 and 2005, cracks were discovered in stringers on the bridge approach spans. The stringers were repaired with bolted splices.

The investigation of the cracking included preliminary analyses, review of historical documents, detailed finite element analyses, and field testing of the bridge. The cracking was determined to …

Corrosion Of Galvanized Fasteners Used In Cold-Formed Steel Framing, Roger A. Laboube

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The primary objective of this project was to study the effect of corrosion on the structural integrity of galvanized fasteners used in cold-formed steel-framed construction. A number of specific tasks were developed to meet this objective, including a literature search, design and construction of field enclosures, determination of test sites and installation of field enclosures, test specimen design and fabrication, accelerated corrosion testing, structural tensile testing, data analysis and technology transfer.

Designing Cold-Formed Steel Using The Direct Strength Method, B. W. Schafer

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The Direct Strength Method is an entirely new design method for cold-formed steel. Adopted in 2004 as Appendix 1 to the North American Specification for the Design of Cold-Formed Steel Structural Members, this paper introduces the Direct Strength Method and details some of the features of a new AISI Design Guide for this Method. The intent of this paper and the Guide is to provide engineers with practical guidance in the application of this new design method. The Direct Strength Method does not rely on effective width, nor require iteration for the determination of member design strength. Instead, the engineer …

Ccfss Technical Bulletin Fall 2006, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Augusta Me: The New Bridge Begets A New Planned Neighborhood, Molly Pulsifer, Richard Barringer

Planning

Construction of a new Third Bridge over the Kennebec River in Augusta offered the prospect of a new and handsome gateway to the city. Further, the resulting change in traffic patterns offered the City the chance to plan for a pattern of development quite different from what the city had experienced for the past half-century. The case study describes the planning and construction of the new bridge and corridors that re-routed traffic out of Augusta’s downtown and older neighborhoods, and created the opportunity for planned development adjacent to the corridor created by the new bridge. It goes on to describe …

Ccfss News Fall 2006, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Comparison Of Aisi Specification Methods For Members With Single Intermediate Longitudinal Stiffeners, B. W. Schafer, Heejae Yang

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

In the current AISI specification, there are two different methods for calculating the effective widths of longitudinally stiffened elements. The first method “B4.1” applies solely to the element with only one intermediate stiffener, whereas the second method “B5.1” works only for those elements with more than one intermediate stiffener. Both methods are accurate in finding the design moments if used appropriately. Although two methods are developed to handle different cases, for some sections with one intermediate stiffener, the second method also works accurately, giving the same result as the first method does for calculating design moments. For some other sections …

Socio-Economic Impacts Of Computer Viruses In Tanzania, M Victor

Tanzania Journal of Engineering and Technology (TJET)

This paper reports on a research project conducted with an objective of identifying and assessing various approaches used by different computer users (Management, System Administrators and end users) in Tanzania to combat computer viruses (CVs), and to assess users' awareness level on CVs. Specifically, the study aimed at assessing the awareness level on CVs to the Tanzanian business community; analyze the socio -economic impact caused by CVs in Tanzania and; assess existing methods, capacity and limitations on controlling CVs in Tanzania. Data was collected using both questionnaires and interview from financial institutions such as NBC and BOT, and telecommunications sector …

Direct Strength Method (Dsm) Design Guide, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The following Design Guide has been developed under the direction of the American Iron and Steel Institute Committee on Specifications for the Design of Cold-Formed Steel Structural Members. The development of the Guide was sponsored by the American Iron and Steel Institute. The AISI Committee on Specifications wishes to acknowledge and expresses gratitude to Dr. Benjamin Schafer of Johns Hopkins University who was the author of this Guide.

With anticipated improvements in understanding of the behavior of cold-formed steel and the continuing development of new technology, this material might become dated. It is possible that AISI will attempt to produce …

Analysis Of Technical Energy Losses By Using Simulation, Betrianis Betrianis, Randite Herawan

Makara Journal of Technology

Model is a representation of a system. Through model, it can be easier to forecast and control the changing of each element system. Electricity distribution is also a system. Losses are general problem that exist in a distribution network system. But with the right methods, specifically technical energy losses can be reduced in order to increase the efficiency. By making model of the distribution network, the value of technical energy losses in the whole network as well as in every line can be observed. Simulation can also be used to see all losses reduction alternatives. By comparing results from each …

Modeling Of Coupled-Tank System Using Fuzzy Takagi-Sugeno Model, Aries Subiantoro

Makara Journal of Technology

Modeling of Coupled-Tank System Using Fuzzy Takagi-Sugeno Model. This paper describes modeling of coupledtank system based on data measurement using fuzzy Takagi-Sugeno model. The fuzzy clustering method of Gustafson- Kessel algorithm is used to classify input-output data into several clusters based on distance similarity of a member of input-output data from center of cluster. The formed clusters are projected orthonormally into each linguistic variables of premise part to determine membership function of fuzzy Takagi-Sugeno model. By estimating data in each cluster, the consequent parameters of fuzzy Takagi-Sugeno model are calculated using weighted least-squares method. The resulted fuzzy Takagi-Sugeno model is …

Design Of Induction Motor Drive Without Velocity Sensor Using Current Vector Controller With Full And Reduced Observer Moving To Dq Axis, Ridwan Gunawan, Feri Yusivar, Wahidin Wahab, Zuhal A. Kadir

Makara Journal of Technology

Design of Induction Motor Drive Without Velocity Sensor Using Current Vector Controller with Full and Reduced Observer Moving to DQ Axis. The observer is used in estimation velocity sensor usually in α-β axis, therefore this situation will need an extra transformation when we want to add compensator because the flux model is in direct and quadrature-axis dq. Every used the transformation to make possible emerge an error. So in this simulation is used a method to estimate the velocity of induction motor drive with observer that is moved to dq-axis. The model of actual motor used is in alfa-beta axis, …

Effect Of Firing Temperature And Holding Time On Characterization Of Al/Sic Metal Matrix Composites Produced By Pressureless Infiltration., Anne Zulfia, Myrna Ariati

Makara Journal of Technology

Effect of Firing Temperature and Holding Time on Characterization of Al/SiC Metal Matrix Composites Produced by Pressureless Infiltration. The production of Al-SiC metal matrix composite can be carried out by pressureless metal infiltration processs (PRIMEX). The experiment was conducted using aluminium AC2B ingot as a matrix and 50%Vf SiC powder as a reinforcement which is mixed with 10% Mg powder for wetting agent. The variables of this experiment are holding time and firing temperature to investigate the effect of these conditions on mechanical properties of Al-SiC metal matrix composites. Holding time was conducted for 2,5,8,10,12 hours and firing temperatures was …

Development Of Fiber-Optic Humidity Sensor Probe With Gelatin Cladding, Akhiruddin Maddu, Kun Modjahidin, Sar Sardy, Hamdani Zain

Makara Journal of Technology

Development of Fiber-Optic Humidity Sensor Probe with Gelatin Cladding. Humidity sensor based on optical fiber with gelatin cladding has been developed. In this humidity sensor probe, the origin cladding of optical fiber is replaced by gelatin coating as humidity sensitive cladding. Testing of the optical fiber sensor probe was conducted by measuring of light intensity transmitted on the optical fiber probe for each variation of different humidity treatments. Response of the optical fiber sensor probe measured from 42%RH to 99%RH, the results show an optical transmission curve varied with relative humidity (RH). Optical transmission in the optical fiber probe increase …

On The Performance Of Imt-2000 Communication Link Based On Stratospheric Platforms, Iskandar Iskandar, Shigeru Shimamoto

Makara Journal of Technology

A new means for providing wireless communication has been currently proposed. It is based on aerial vehicle known as High Altitude Platform or Stratospheric Platforms (SPF). The SPF will be operated at an altitude of 17-22 km above the ground. Therefore, the channel condition may be different compared with those of the conventional terrestrial or satellite wireless channel. In this paper, the channel propagation characteristic of such a system is firstly investigated by means of ray tracing algorithm. We emphasize our investigation in a typical urban environment, in which the mobile users mostly exist. We developed building block model for …

Modification Of Bonding Strength Test Of Wc Hvof Thermal Spray Coating On Rocket Nozzle, Bondan T. Sofyan, Haposan J. Pardede, Marizki Stefano, Edi Sofyan

Makara Journal of Technology

Modification of Bonding Strength Test of WC HVOF Thermal Spray Coating on Rocket Nozzle. One way to reduce structural weight of RX-100 rocket is by modifying the nozzle material and processing. Nozzle is the main target in weight reduction due to the fact that it contributes 30 % to the total weight of the structur. An alternative for this is by substitution of massive graphite, which is currently used as thermal protector in the nozzle, with thin layer of HVOF (High Velocity Oxy-Fuel) thermal spray layer. This paper presents the characterization of nozzle base material as well as the modification …

Hybrid Identification System With Arx And Fast Fourier Transform In Application Of A Quarter Of Vehicle Half Active Suspension, Noveri Lysbetti M, Antonius R.

Makara Journal of Technology

Hybrid Identification System with ARX and Fast Fourier Transform in Application of a Quarter of Vehicle Half Active Suspension. In a control system problem, identification system mechanism is a absolute thing, especially in adaptation controlling to disturbance changing. For that case, is needed an identification method which can identify the changing of disturbance in that system. The aim of this research is to give an alternative in system/plant identification which is a combination (hybrid) of ARX and Fast Fourier Transform. So, it is needed an algorithm design for identification process. In this case, the designed algorithm will be implemented in …

Ccfss Technical Bulletin Spring 2006, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Collapse Of The Quebec Bridge, 1907, Cynthia Pearson, Norbert Delatte

Civil and Environmental Engineering Faculty Publications

In the late 19th century, the transportation needs of Quebec led to proposals for bridging the St. Lawrence River. The Quebec Bridge was the longest cantilever structure attempted until that time. In its final design, the clear span was 548.6 m (1,800 ft) long. The bridge project was financially troubled from the beginning. This caused many setbacks in the design and construction. Construction finally began in October 1900. In August 1907, the bridge collapsed suddenly. Seventy five workers were killed in the accident, and there were only 11 survivors from the workers on the span. A distinguished panel was assembled …

Ccfss News Spring 2006, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Galvanized Steel Framing For Residential Buildings, Nahb Research Center, Inc.

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Study Of Same-Lane And Inter-Lane Gvw Correlation, Bernard Enright, Eugene J. O'Brien, Colin C. Caprani

Conference papers

The methodology used is to generate a number of years of simulated traffic and to use extreme value statistics to predict more accurately the characteristic loading for a given bridge. The parameters and probability distributions used in the Monte Carlo simulation must be based on observed sample traffic data. Some previous studies have made unsubstantiated assumptions regarding correlation between the Gross Vehicle Weights (GVW) of trucks in the same lane, or between trucks in adjacent, same-direction lanes. For this paper, an extensive database of Dutch Weigh-in-Motion data is analysed. Data are collected from two same-direction lanes and are time-stamped to …

The Girl Scout Climbing Wall Multidisciplinary Service-Learning Project, Margaret Pinnell, Corinne M. Daprano, Gabrielle Williamson

Mechanical and Aerospace Engineering Faculty Publications

The Girl Scout Wall (GS Wall) project was implemented in two classes at the University of Dayton (UD): a Mechanical and Aerospace Engineering (MAE) course, and a Health and Sports Science (HSS) course, and Sport Facility Management. The MAE course, Introduction to Materials, is a three-credit, third-year required course where students learn about the basic structure and properties of materials as well as the principles of material selection. The Sport Facility Management course is a three-semester hour, required HSS course where students are introduced to the processes of planning, constructing, equipping, maintaining, and managing sport facilities.

Residential Hip Roof Framing Using Cold-Formed Steel Members, Luke Waldo, Sutton F. Stephens, Roger A. Laboube

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Development Of Cost-Effective, Energy Efficient Steel Framing: Structural Performance Of Slit-Web Steel Wall Studs, Nahb Research Center

CCFSS Library (1939 - present)

No abstract provided.

Development Of Cost-Effective, Energy Efficient Steel Framing: Thermal Performance Of Slit-Web Steel Wall Studs, Nahb Research Center

CCFSS Library (1939 - present)

No abstract provided.