Structural Engineering Commons^™

Examining The Effects Of Reducing The Cement Content Of Portland Cement Concrete Pavement, Bryan Casillas

Graduate Theses and Dissertations

Portland cement is a significant component in a concrete mixture. For concrete used in portland cement concrete pavement (PCCP), the Arkansas Department of Transportation (ARDOT) specifies a minimum cementitious material content of 564 lb/yd3 and a maximum water-cementitious material ratio of 0.45. Prior research conducted at the University of Arkansas, TRC 0603, indicated concrete mixtures used in five bridge decks throughout Arkansas achieved the required 28-day strength at seven days, and the measured compressive strength at 28 days was 30% greater than required. The use of high strength concrete in pavements throughout the state can increase cracking and consequently reduce …

Verifying The Calcium Oxychloride Threshold In Cementitious Pastes, Fatoumata Traore

Graduate Theses and Dissertations

Calcium oxychloride (CAOXY) formation is a serious deterioration mechanism known to cause joint damage in concrete pavements. CAOXY is the product of a chemical reaction between calcium chloride (CaCl2) or magnesium chloride (MgCl) deicing salts and calcium hydroxide in the cementitious matrix. Currently, the accepted CAOXY threshold at which deterioration is mitigated in cementitious paste is 15 g/100 g paste (15 oz/100 oz paste); however, this limit was developed using flexural strength testing. For this investigation, the current threshold was evaluated using compressive strength and mass change over time in paste specimens exposed to CaCl2. Fly ash is used to …

Commodity-Based Freight Activity On Inland Waterways Through The Fusion Of Public Datasets For Multimodal Transportation Planning, Magdalena I. Asborno

Graduate Theses and Dissertations

Within the U.S., the 18.6 billion tons of goods currently moved along the multimodal transportation system are expected to grow 51% by 2045. Most of those goods are transported by roadways. However, several benefits can be realized by shippers and consumers by shifting freight to more efficient modes, such as inland waterways, or adopting a multimodal scheme. To support such freight growth sustainably and efficiently, federal legislation calls for the development of plans, methods, and tools to identify and prioritize future multimodal transportation infrastructure needs. However, given the historical mode-specific approach to freight data collection, analysis, and modeling, challenges remain …

On The Seismic Performance Of Skewed Special Moment Frame Reduced Beam Section Connections, Damaso Daniel Dominguez

Graduate Theses and Dissertations

Special Moment Frames (SMFs) are frequently used in high seismic areas for architecturally constrained designs, as they provide lateral system stiffness without the use of braces which often obstruct views and architectural features. Reduced beam section (RBS) connections are popular SMF connection details developed following the Northridge earthquake to limit brittle fractures within connection welds. Current American Institute of Steel Construction (ASIC) provisions (i.e. AISC 341-16) provide prequalified SMF RBS connection details (including welding requirements); however, all prequalified details only consider orthogonal connections between the beam and column. This dissertation investigates the effect of adding skew within SMF RBS connections …

Numerical Simulations Of Spread Foundations Supported On Stone Columns Using The Discrete Element Method, Anibal Enrique Santos Marin

Graduate Theses and Dissertations

The implementation of stone columns as a ground improvement technique has become more popular in geotechnical construction practice as a result of their ability to improve strength, stiffness and permeability characteristics of weak clayey soil deposits. There are several analytical and empirical approaches to estimate the bearing capacity of stone column foundation systems; however, there is notable variation in the performance of these existing methods when compared with full-scale experimental results. For very weak cohesive soils (i.e., undrained shear strength less than 15 kPa), the use of conventional stone columns becomes restricted because of the insufficient confinement that these types …

Incorporating Geophysical Data In Slope Stability Modeling For Two Slopes In Arkansas, Vanessa Lebow

Graduate Theses and Dissertations

Slope failures in the United States alone cause millions of dollars in damage to infrastructure, threaten national monuments, create environmental hazards, and take an average of 25-50 lives a year. With the inevitable construction that occurs on slopes, it is imperative that the slopes be properly designed which requires a thorough understanding of slope grade, subsurface soil conditions, soil strength parameters, water table locations, and depth to bedrock across the entire site. The preferred method of data collection would be to use borings and other in-situ methods; however, sometimes due to cost constraints or site accessibility only a very limited …

Evaluation Of Concrete Deck Curing Regimens Using Capillary Pressure Sensing System, Samuel Spann

Graduate Theses and Dissertations

Early-age plastic shrinkage cracking is a common problem with the construction of concrete bridge decks due to the high surface area-to-volume ratio and exposure to potentially detrimental environmental effects. Curing regimens are utilized to mitigate cracking risk during the plastic stage of the concrete; the curing regimens evaluated for this study were wet burlap-polyethylene sheeting, two acrylic curing compounds, and one lithium compound. Capillary pressure in the water filled pores has been shown to correlate to the plastic shrinkage cracking risk of concrete. A new portable system has been developed to measure the capillary pressure that could potentially be used …

Truck Activity Pattern Classification Using Anonymous Mobile Sensor Data, Taslima Akter

Graduate Theses and Dissertations

To construct, operate, and maintain a transportation system that supports the efficient movement of freight, transportation agencies must understand economic drivers of freight flow. This is a challenge since freight movement data available to transportation agencies is typically void of commodity and industry information, factors that tie freight movements to underlying economic conditions. With recent advances in the resolution and availability of big data from Global Positioning Systems (GPS), it may be possible to fill this critical freight data gap. However, there is a need for methodological approaches to enable usage of this data for freight planning and operations.

To …

Study Of Internal Strains Developed In Concrete Decks At Early Ages In Steel Continuous Bridges, Fernando R. Benitez Ortiz

Graduate Theses and Dissertations

The Arkansas Department of Transportation (ARDOT) has identified bridge deck cracking shortly after concrete decks are placed and prior to applying traffic loads. Previous researchers have confirmed improper construction practices and design methods can lead to deck cracking. Currently, many contractors throughout Arkansas are using continuous deck pours. This construction approach may restrict the concrete slab from movement during early age shrinkage, causing tensile stresses to develop. The final stresses at the end of construction must be lower than the concrete tensile strength, if not cracking issues will develop. Eventually, these cracks may enlarge due to service load stresses and …

Evaluation Of Fracture Principles In Asphalt Concrete Utilizing The Sc(B) Geometry, Airam Marlee Morales Vega

Graduate Theses and Dissertations

Since cracking is one of the principal distresses to be considered in asphalt concrete, multiple fracture tests and geometries have been used to quantify cracking resistance. One of the most popular geometries that have been used in fracture tests is the Semi-Circular bend (SC(B)). However, for this geometry, most of the fracture test methods use different parameters such as thickness, testing temperatures, and loading rates. Thus, the purpose of this research was first to evaluate fracture energy by performing a ruggedness test based on ASTM E1169. Then, to apply fracture mechanics concepts to evaluate three specimen thicknesses (25, 50, and …

Utilizing The Hvsr Second Peak For Surface Wave Inversions In The Mississippi Embayment, Ashraf Kamal Himel

Graduate Theses and Dissertations

Ambient noise data from 24 sites within the Mississippi Embayment were analyzed to estimate the fundamental frequency using the horizontal to vertical spectral ratio (HVSR) method. The fundamental frequency ranged from 0.17 to 3.43 Hz for the tested sites. At seventeen of the sites, a second higher frequency HVSR peak, which ranged from 0.617 Hz to 2.154 Hz, was observed in addition to the fundamental HVSR peak. The second peak frequency in the HVSR curve has been attributed by previous researchers as either an odd harmonic of the fundamental peak or a shallow impedance contrast from the Memphis sand layer …

Developing Computer Codes For Analyzing Bridge Response Due To Wim Data Truck Loading, Kenneth Patrick Pasley

Graduate Theses and Dissertations

Despite actual truck demographics evolving over the past 30 years, the Arkansas legal loads for bridge posting have not been updated. Custom computer codes were developed.to facilitate comparison between the current Arkansas legal loads for bridge posting and the actual Arkansas truck traffic to ensure that actual reactions are enveloped by the state'. The program, WIMFluence, calculates shear and moment influence lines for a bridge and the resulting shear and moment reactions based on weigh-in-motion data. With supporting scripts, the reactions due to actual Arkansas truck traffic were compared to those due to the current Arkansas legal loads for bridge …

On The Development Of 8,000 Psi Geopolymer Mortar For Practical Use In Field Applications, Remington Gabriel Reed

Graduate Theses and Dissertations

Although there are several perceived benefits from the use of geopolymer binder as an alternative to ordinary portland cement in concrete materials, it is not widely used in field applications. Geopolymer materials have no set guidelines for mixture design and often require heat curing to facilitate strength gain. Additionally, many geopolymers are created using carefully controlled and high quality materials and activator chemicals. These factors greatly affect the practicality of the material. The goal of this research was to create a geopolymer material capable of achieving high compressive strengths at 28 days without heat curing, and using only readily available …

Developing Ultra-High Performance Concrete (Uhpc) With Locally Available Materials, Ali Alsalman

Graduate Theses and Dissertations

Ultra-High Performance Concrete (UHPC) can enhance the durability and resilience of concrete structures. The use of local materials is a fundamental step to save energy and reduce the cost of concrete. The main focus of this research was to develop a UHPC with compressive strength of 150 MPa using locally sources materials. In this study, the effect of fine materials, binder type and content, type of mixer, steel fibers and curing regimes on concrete’s compressive strength were investigated. The relationship between compressive strength and elastic modulus was also studied. This study synthesizes all relevant experimental data in the literature to …

Effect Of Continuity Plate Eccentricity On The Performance Of Welded Beam-To-Column Connections, Jason Thomas Norwood

Graduate Theses and Dissertations

Beam-to-column connections in structural steel buildings may have varying degrees of rotational restraint and varying degrees of moment transfer. In fully restrained moment connections, shear is typically transferred through the beam web, while the moment is mostly transferred through the beam flanges which create tension/compression force couples. Column sections that are incapable of resisting these flange forces are often retrofitted with continuity plates within the connection region to improve capacity. In cases of unequal beam depths on either side of the column, an eccentricity between the framed-in beam flange and continuity plate may be required; however, limited research exists to …

Effect Of Cement Content On Concrete Performance, Caleb Joshua Lebow

Graduate Theses and Dissertations

Of all the traditional concrete materials, portland cement has the greatest impact on mixture cost and the environment. Cement is in many ways the glue holding concrete together (Weiss, 1999), and as such, it plays a major role in fresh and hardened concrete properties. Without the proper range of cement in the mixture, low strength development or excessive shrinkage may occur leading to premature deterioration. The Arkansas Department of Transportation (ARDOT) recognizes two types of concrete for use in bridge construction, Class S and Class S(AE). This paper focuses on the findings from testing of Class S(AE) concrete, short for …

Testing And Development Of Pre-Stressed Cfrp Retrofit Strategies For Controlling Fatigue Cracking In Steel Waterway Lock Gate Structures, Maggie Langston

Graduate Theses and Dissertations

Steel waterway lock gates across the national inland waterway transportation network are reaching and exceeding their intended service life, often experiencing component failures that lead to service interruptions. Unscheduled maintenance and repair of lock gates can be expensive and cause economic ripples throughout the entire inland waterway network. These lock gate component failures are often caused by fatigue cracking from repeated loading during operation. This thesis develops and tests a prestressed carbon fiber reinforced polymer (CFRP) fatigue retrofit for controlling fatigue demands within lock gate components. The study expands upon a recent analytical work by Lozano (2017) by experimentally investigating …

Liquefaction-Induced Dragload And/Or Downdrag On Deep Foundations Within The New Madrid Seismic Zone, Ishimwe Elvis

Graduate Theses and Dissertations

Deep foundation elements are typically used to transfer structural loads for multi-story buildings and large-span bridges to a competent soil layer when 1) the soil close to the ground surface has no sufficient bearing capacity, and when 2) liquefiable soils are encountered. The majority of the bridges constructed within seismic zones rely upon the stability of earthen embankments and deep foundation that are installed above or within liquefiable soil deposits. Despite large factor of safety values or different load and resistance factors being used to adequately design deep foundations within seismic areas, soil liquefaction may cause extensive damage to the …

Automated Pin-Dot Marking Effects On A709-Gr50 Steel Plate Fatigue Capacity, Michael Andrew Noernberg

Graduate Theses and Dissertations

During fabrication of multi-piece steel bridge assemblies, markings are often made on the steel surface to identify/track individual pieces or to provide reference for fabrication layout or later erection. Automated marking methods such as computer numerically controlled (CNC) pin-dot marking offer fabrication efficiencies; however, for marked steel sections subjected to frequent or repeated loading (i.e. bridge girders) many code specifications require experimental testing to verify any marking effects on fatigue capacity. In this study, the effects of automated pin-dot markings on the fatigue capacity of A709-Gr50 bridge steel are experimentally investigated from 13 specimens considering 2 marking frequencies (corresponding to …

Systematic Review For Water Network Failure Models And Cases, Yufei Gao

Graduate Theses and Dissertations

As estimated in the American Society of Civil Engineers 2017 report, in the United States, there are approximately 240,000 water main pipe breaks each year. To help estimate pipe breaks and maintenance frequency, a number of physically-based and statistically-based water main failure prediction models have been developed in the last 30 years. Precious review papers focused more on the evolution of failure models rather than modeling results. However, the modeling results of different models applied in case studies are worth reviewing as well.

In this review, we focus on research papers after Year 2008 and collect latest cases without repetition. …

Soil-Structure Interaction Effects On The Seismic Response Of Low-Rise Eccentrically Braced Frames, Luis Gerardo Buitrago Goyez

Graduate Theses and Dissertations

The importance of soil-structure interaction (SSI) effects on the seismic response of buildings has been long recognized and has been researched for over 40 years. However, SSI analysis has only been applied in a few building projects because the fixed base condition is considered to provide a conservative estimation for the response of buildings under seismic loads. This assumption of a fixed base condition adopted by practitioners is not always conservative or cost-effective, especially for rigid buildings over soft soils. Additionally, for the case of ductile steel frames with eccentric configurations, the influence of SSI on their seismic performance has …

Effect Of Column Axial Load On Skewed Smf Rbs Connection Demands, Clovis Desrochers

Graduate Theses and Dissertations

Steel buildings in high seismic areas often require special structural systems to transfer large lateral forces induced by earthquake accelerations. The selection of an appropriate seismic steel system (braced frame, moment frame, shear wall, etc.) is often influenced by architectural considerations. Moment frame configurations offer the most architectural flexibility, but are limited by code prequalification requirements that limit the use of non-orthogonal (skewed) beam-column connection geometries. A recent study has investigated laterally skewed moment frame connections, indicating that skew increases the potential for column twist and column flange yielding; however, it is unclear how realistic column axial loads will affect …

A Comparison Of Force And Pressure Coefficients On Dome, Cube And Prism Shaped Buildings Due To Straight And Tornadic Wind Using Three Dimensional Computational Fluids Dynamics, Majdi A. A. Yousef

Graduate Theses and Dissertations

Tornadoes induce very different wind forces than a straight-line (SL) wind. A suitably designed building for a SL wind may fail when exposed to a tornado-wind of the same wind speed. It is necessary to design buildings that are more resistant to tornadoes. Most studies have been conducted to investigate tornado forces on cubic, gable-roof and cylinder buildings. However, little attention has been paid to investigate tornado force on dome buildings; hence, further research is conducted in this study. The forces on a dome, cube and prisms were analyzed and compared using Computational Fluid Dynamics (CFD) for tornadic and SL …

Identifying Damage, Predicting Expansion, And Determining The Effectiveness Of Sealers On Concrete Affected By Alkali-Silica Reaction And Freeze-Thaw, Matthew Caleb Waidner

Graduate Theses and Dissertations

Premature cracking of the barrier wall and pavement on I-49 south of Fayetteville, Arkansas due to a combination of Alkali-Silica Reaction (ASR) and freeze-thaw has led to ASR and freeze-thaw research at the University of Arkansas. Potential for further expansion (PFET), Damage Rating Index (DRI), and mitigation of freeze-thaw and ASR with sealers testing and results are contained herein. PFET results indicated that the pavement will not continue to expand from ASR. With other interstate pavements deteriorating prematurely throughout Arkansas, DRI has shown that most are damaged not only by ASR but by freeze-thaw too. Recommendations for freeze-thaw’s inclusion into …

Creep, Fatigue And Creep-Fatigue Interactions In Modified 9% Cr - 1% Mo (P91) Steels, Valliappa Kalyanasundaram

Graduate Theses and Dissertations

Grade P91 steel, from the class of advanced high-chrome ferritic steels, is one of the preferred materials for many elevated temperature structural components. Creep-fatigue (C-F) interactions, along with oxidation, can accelerate the kinetics of damage accumulation and consequently reduce such components' life. Hence, reliable C-F test data is required for meticulous consideration of C-F interactions and oxidation, which in turn is vital for sound design practices. It is also imperative to develop analytical constitutive models that can simulate and predict material response under various long-term in-service conditions using experimental data from short-term laboratory experiments. Consequently, the major objectives of the …

Development Of Mems-Based Corrosion Sensor, Feng Pan

Graduate Theses and Dissertations

This research is to develop a MEMS-based corrosion sensor, which is used for monitoring uniform, galvanic corrosion occurring in infrastructures such as buildings, bridges. The corrosion sensor is made up of the composite of micro/nano metal particles with elastomers. The mechanism of corrosion sensor is based on the mass transport of corrosive species through the sensor matrix. When the metal particles in the matrix corrode, the electrical resistivity of the material increases due to increasing particle resistances or reduction of conducting pathways. The corrosion rate can be monitored by detecting the resistivity change in sensing elements. The life span of …

Improved Protocols For Automated Wheelpath Crack Detection In Pavements, Daniel Patrick Byram

Graduate Theses and Dissertations

Roadway pavement distress evaluations are vital to understanding the mechanics of pavement stability, determining the distribution of rehabilitation costs, and knowing the appropriate rehabilitation strategies. Advancements in technology over the past two decades have changed the way these surveys have been performed by means of automated data collection and interpretation. More and more state agencies have invested in automated road analyzing vehicles that are able to collect high resolution images of the pavement. Fewer have adopted automated data processing software with the ability to interpret road distresses due to the common discrepancies in distress classification algorithms.

In addition to automated …

Slope Stability Monitoring Using Remote Sensing Techniques, Omar Alberto Conte Robles

Graduate Theses and Dissertations

During the past six years the Arkansas State Highway and Transportation Department (AHTD) has spent over nine million dollars repairing slope failures that have occurred in the state of Arkansas. Specifically, higher than average precipitation in 2004 and 2008 led to large quantities of slides, all of which were repaired. Two highways, within the state of Arkansas, with known historical movements along or across the highways are being monitored using traditional surveying techniques and advanced remote sensing techniques. These slides, both of which are located in fill slopes. One a 500-foot long slide located north of Chester, Arkansas, within the …

Computer Modeling Of The Influence Of Structure Plan Areas On Tornado Forces, Nashmi Hassan M Alrasheedi

Graduate Theses and Dissertations

The study of the conventional Straight Line (SL) wind flow dominates research into wind loads on structures. Most structure design takes into account only research into SL flow. Few researchers have studied tornado forces on buildings and attempted to distinguish between tornadic wind loads and SL flow loads. Using a computer simulation, this research addresses and distinguishes between the tornadic forces and SL forces on structures. In the numerical simulation, tornado forces and SL forces will be compared on large structure plan areas and on thin structure plan areas. Additionally this research investigates how the increase in the vortex strength …

Laboratory Evaluation Of Dynamic Characterization Methods For Rapid Condition Assessment Of Bridges, Jason Kyle Herrman

Graduate Theses and Dissertations

The objective of this thesis was to devise and refine Structural Health Monitoring methods and the associated quantitative characterization methods with the specific goal of enabling rapid and reliable safety evaluations of bridges following natural or manmade hazards. Presently, the safety and serviceability of these transportation infrastructure assets for use in emergency response and recovery operations are evaluated through on-site visual inspections of individual structures by teams of specially trained engineers or technicians; a process that is manpower-intensive, subjective, and slow. Specifically, the researcher was able to identify and evaluate strategies and procedures for using dynamic testing methods to rapidly …