Structural Engineering Commons^™

The Application Of Gray-Scale Level-Set Method In Segmentation Of Concrete Deck Delamination Using Infrared Images, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Conventional nondestructive delamination detection of concrete pavements through thermography is often based on temperature contrasts between delaminated and sound areas. Non-uniform backgrounds caused by the environmental conditions are often challenging for contrast-based methods to robustly differentiate the delaminated areas from the sound areas. Instead of focusing on the temperature contrast, this study proposes a temperature gradient-based level set method (LSM) to detect boundaries for delamination segmentations. A modified edge indicator function is developed to represent the normalized temperature gradient of a thermal image. The experimental study was conducted to evaluate its applicability and stability for boundary detection in terms of …

Probabilistic Analysis Of Slide-Rocking Structures Under Earthquake Loads, Taylor J. Knickerbocker

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Estimates of rare seismic hazard are essential for the resilience of critical infrastructure and facilities. However, these estimates are highly uncertain at long return periods due to the lack of observed earthquake records. Several ground motion prediction equations have been proposed to close this gap and estimate rare seismic demands; however, these models were developed based on more moderate earthquake records and can yield physically unrealizable ground motions when extrapolated to long return periods. For this reason, seismologists have proposed using precariously balanced rocks (PBRs) as a way to constrain rare seismic hazard. PBRs are a type of fragile geologic …

Unl-Cc Outdoor Education Center Master Plan, Marie Wagner

Honors Program: Senior Projects (Public)

The following report contains the work done by the group Griswold Engineering in completion of the Senior Design requirements for Civil Engineering and the Honors Requirements of the Project Manager. As the project manager, my job was to organize the project as a whole and to work alongside the Structural Engineer on the project. One of the main problems to overcome was the division of labor amongst the group. The project was originally conceived as a group project with one project manager and five other students to serve as the project engineers in each subdiscipline. Since this group only had …

Development Of Post-To-Deck Connections For Use In A Mash Tl-4 Steel-Tube Bridge Rail, Pascual Mauricio

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

A new post-to-deck connection was designed for mounting an upcoming Manual for Assessing Safety Hardware (MASH) Test Level 4 steel-tube bridge rail to the side of the bridge deck to limit impact load transferred to the deck and to minimize the propensity for deck damage during impacts. With preference for the bridge rail system to be compatible for use on all deck configurations, the Illinois and Ohio Departments of Transportation desired the new system to attach to bridge decks comprised of concrete slabs or precasted prestressed, concrete box-beam girders.

A new post-to-deck connection for a new MASH 2016 TL-4 steel-tube …

Civil Engineering Design Of Cornhusker Council's Outdoor Education Center, Kelly Weiler

Honors Program: Senior Projects (Public)

A team of geotechnical, structural, hydraulic, environmental, and transportation experts collaborated to provide engineering solutions to the Cornhusker Council in an effort to solve the current problems facing their Outdoor Education Center. This results of this project provided the structural design of three bridges on the property, transportation plans for two parking lots and roadway design, geotechnical recommendations for soil testing and erosion prevention, and an environmental and hydraulic analysis of the property. A major challenge in the design of this project is the consideration of the dangers and regulations that accompany the floodway and floodplain regions on site. Various …

Bridge Deck Delamination Segmentation Based On Aerial Thermography Through Regularized Grayscale Morphological Reconstruction And Gradient Statistics, Chongsheng Cheng, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Environmental and surface texture-induced temperature variation across the bridge deck is a major source of errors in delamination detection through thermography. This type of external noise poises a significant challenge for conventional quantitative methods such as global thresholding and k-means clustering. An iterative top-down approach is proposed for delamination segmentation based on grayscale morphological reconstruction. A weight-decay function was used to regularize the reconstruction for regional maxima extraction. The mean and coefficient of variation of temperature gradient estimated from delamination boundaries were used for discrimination. The proposed approach was tested on a lab experiment and an in-service bridge deck. The …

Exploring Engineering Club, Samantha Corey, Stephen Yaghmour

Honors Program: Expanded Learning Clubs

Exploring Engineering Club provides an introduction to a variety of engineering problems and piques the students’ interest in engineering by accompanying the information with hands-on problem solving activities mainly related to structural engineering. The activities will often be done in teams which will teach good teamwork skills, as well as problem solving and critical thinking.

Post-Earthquake Assessment And Numerical Modeling Of Freestanding Heritage Structures, M. Khalid Saifullah, Christine E. Wittich

Department of Civil and Environmental Engineering: Faculty Publications

Historic and heritage structures are particularly vulnerable to earthquakes, where damage or collapse can not only lead to loss of a structure but also the loss of irreplaceable heritage. Many heritage structures can be classified as freestanding (detached) structures, including unreinforced masonry walls, classical multi-drum columns, and statue-pedestal systems. However, the seismic response of freestanding structures (sliding, rocking, rock-slide, overturning) is poorly predicted by existing methods due to geometric non-linearities as well as sensitivity to interface conditions and modeling parameters. Previous studies have focused on analytical modeling of simplified systems and/or experimentation under controlled laboratory conditions. In contrast, this paper …

Post-Fire Damage Geospatial Assessment Via Point Clouds Of A Highway Bridge Structure, Yijun Liao, M Ebrahim Mohammadi, Richard L. Wood, Christine E. Wittich

Department of Civil and Environmental Engineering: Faculty Publications

This paper discusses the quantitative post-fire damage assessment of a steel girder bridge via point clouds. In this case study, the point cloud was collected using light detection and ranging (lidar) for a detailed geometric and shape analysis. The out-of-plane deformation was analyzed to locate and quantify buckling across the length of the steel girders.

Efficient Intensity Measures Of Slide-Rocking Structures For Precariously Balanced Rocks, Taylor J. Knickerbocker, Christine E. Wittich

Department of Civil and Environmental Engineering: Faculty Publications

Precariously balanced rocks (PBRs) and other fragile geologic features are important in both the engineering and seismological communities since they are indicative of the maximum ground motion at a site over the rock’s lifetime. Precariously balanced rocks are individual or stacks of freestanding rocks that tend to respond in rigid body modes when subject to seismic excitation – namely, rocking, sliding, slide-rocking, and free-flight, which can lead to overturning. The seismic response of freestanding structures, such as PBRs, is known to be extremely sensitive to small changes in geometry, position, and earthquake excitation. As such, deterministic methods are limited in …

Damage Assessment Of A Sixteen Story Building Following The 2017 Central Mexico Earthquake, Yijun Liao, Richard L. Wood, M Ebrahim Mohammadi, Kanchan Devkota, Christine E. Wittich

Department of Civil and Environmental Engineering: Faculty Publications

The 2017 M7.1 Central Mexico Earthquake caused significant infrastructural damage in the Mexico City area. The earthquake contained a significant pulse in the long period, resulting in numerous buildings severely damaged or collapsed. This paper discusses a reinforced concrete building which was still partially occupied post-earthquake. The building’s interior walls were examined to have substantial damage, including some extensive cracking. In January 2018, the authors visited the structure and collected detailed assessment data. The data collection included ground-based lidar scans and recorded ambient vibrations of the damaged structure using accelerometers. Eleven scans were collected from the four exterior facades to …

Assessing Impact And Blast Resilience Of Polymer Coated Cementitious Materials, Murtaza Nalwala, Gabriel Nsengiyumva, Yong-Rak Kim

UCARE: Research Products

RESEARCH MOTIVATION The bridge piers are highly vulnerable to the impact and blast loads. The position in which they are constructed makes it difficult to install protective devices around them. By the current AASHTO standard, it is possible to under-design bridge piers for commercial vehicle impacts and other events such as blast.

OBJECTIVE To improve impact and blast resilience of bridge piers using polymeric coatings.

CONCLUSION Polymer coating of Portland cement concrete can be achieved with a good bonding. ü The polymeric coating seem to improve impact resilience of Portland cement concrete by increasing absorbed impact energy (i.e., area underneath …

Evaluation Of Deformable Posts In The Zoi And Rigid Posts In Stiff Soil, Thomas Ammon

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Debris fences are commonly used by states, in conjunction with a concrete parapet, to protect railway tracks. Their use limits the intrusion of debris that could damage tracks or clutter rail lines. Due to a lack of previously crash-tested systems, the safety performance of such designs are largely unknown. The Iowa Department of Transportation (DOT) desired that researchers at the Midwest Roadside Safety Facility (MwRSF) design a crashworthy debris fence mounted on top of a concrete parapet to meet the Manual for Assessing Safety Hardware (MASH) TL-3 crash test conditions. Part 1 of this thesis details the literature review and …

Investigation Of A Tractor-Tank Trailer Roadside Containment Barrier, Dean L. Whitfield

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The objective of this research project was to develop a new, cost-effective, Manual for Assessing Safety Hardware (MASH) Test Level 6 (TL-6) barrier. A literature review on prior Test Level 5 and Test Level 6 barriers was conducted, and the cost of current TL-5 and TL-6 barriers was established. Existing and modified design procedures for roadside barrier were reviewed as well as current TL-6 design forces. A preliminary TL-6 truck model was developed in LS-DYNA. The minimum barrier height to contain a tractor-tank vehicle was determined to be 62 in. for a rigid, vertical-faced barrier through LS-DYNA computer simulation. New …

Development Of Iowa Dot Combination Bridge Separation Barrier With Bicycle Railing, Chaz M. Ginger

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The Iowa Department of Transportation typically builds separation barriers between vehicle and pedestrian/bicycle facilities when sidewalks or trails are present on vehicular bridges. Currently, Iowa DOT employs a combination bridge rail that utilizes a concrete parapet that previously had been successfully evaluated to National Cooperative Highway Research Program (NCHRP) Report 350 Test Level 4 (TL-4) criteria for these situations. While the parapet had been successfully evaluated, the combination bridge rail system as a whole had not been evaluated to any crash test standards. Iowa DOT desired that researchers at Midwest Roadside Safety Facility (MwRSF) design and test a combination bridge …

Evaluation And Development Of Cpt Based Pile Design In Nebraska Soils, Alex Silvey

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Cone penetration testing (CPT) is a well established geotechnical subsurface investigation technique commonly used for site characterization and soil classification. The CPT gives real time end resistance, side friction, and pore pressure readings. Axially loaded piles also share these two resistance mechanisms, suggesting the cone can be considered similar to a miniature pile. This study focused on evaluating eight CPT methods prediction of pile bearing capacity. The Nebraska Department of Roads (NDOR) conducts dynamic load tests (PDA) of driven pile to verify pile capacity for bridge foundations. 91 comparisons of CPT logs and PDA data were evaluated. CPT prediction methods …

3-D Reconstructions And Numerical Simulations Of Precarious Rocks In Southern California, Christine E. Wittich, Tara C. Hutchinson, J. Desanto, D. Sandwell

Department of Civil and Environmental Engineering: Faculty Publications

Reliable estimates of seismic hazard are essential for the development of resilient communities; however, estimates of rare, yet high intensity earthquakes are highly uncertain due to a lack of observations and recordings. Lacking this data, seismic hazard analyses may be based on extrapolations from earthquakes with more moderate return periods, which can lead to physically unrealistic earthquake scenarios. However, the existence of certain precariously balanced rocks (PBRs) has been identified as an indicator of an upper bound ground motion, which precludes toppling of the balanced rock, over its lifetime. To this end, a survey of PBRs was conducted in proximity …

Examination Of Steel Pin And Hanger Assembly Performance: Retrofit To Replacement, Chandana Chickamagalur Balakrishna

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

A number of steel, multi-beam bridges exist in the United States that contain pin and hanger assemblies. Pin and hanger assemblies are fracture critical members whose failure would result in collapse of the bridge or render it unable to perform its expected functions. As these bridges continue to age, many assemblies have deteriorated to a point where retrofit or replacement has to be considered and performed to maintain intended safety and performance. States have taken various approaches to address the pin and hanger assembly retrofit and replacement options. However, there is no single document that summarizes these approaches.

This research …

Optimized Health Monitoring Plans For A Steel, Double-Track Railway Bridge, Ahmed Rageh

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Railway bridges are an essential component of any modern society and play a significant transportation role. During the 19^th and early 20^th centuries steel truss and plate girder bridges were commonly used railway designs, with most of the trusses constructed using pin and eyebar systems and most other load carrying members being riveted, built-up sections.

Many of these bridges are still in use and are subjected to increased railway traffic intensity, loads and speeds. The current practice for evaluating the integrity of bridges in the United States, irrespective of use, is primarily via visual inspection, with those inspections …

Mechanical Characterization Of Polysilicon Mems: A Hybrid Tmcmc/Pod-Kriging Approach, Ramin Mirzazadeh, Saeed Eftekhar Azam, Stefano Mariani

Department of Civil and Environmental Engineering: Faculty Publications

Microscale uncertainties related to the geometry and morphology of polycrystalline silicon films, constituting the movable structures of micro electro-mechanical systems (MEMS), were investigated through a joint numerical/experimental approach. An on-chip testing device was designed and fabricated to deform a compliant polysilicon beam. In previous studies, we showed that the scattering in the input–output characteristics of the device can be properly described only if statistical features related to the morphology of the columnar polysilicon film and to the etching process adopted to release the movable structure are taken into account. In this work, a high fidelity finite element model of the …

Multi-Point Vibration Measurement And Mode Magnification Of Civil Structures Using Video-Based Motion Processing, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Image-based vibration measurement has gained increased attentions in civil and construction communities. A recent video-based motion magnification method was developed to measure and visualize small structure motions. This new approach presents a potential for low-cost vibration measurement and mode shape identification. Pilot studies using this approach on simple rigid body structures were reported. Its validity on complex outdoor structures has not been investigated. In this study, a non-contact video-based approach for multi-point vibration measurement and mode magnification is introduced. The proposed approach can output a full-field vibration map that increases the efficiency of the current structural health monitoring (SHM) practice. …

Structural Identification And Assessment Of The Inverted Tee Girder Bridge System, Garrett P. D. Martindale

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The Inverted Tee (IT) girder bridge system was originally developed in 1996 by the University of Nebraska–Lincoln (UNL) and Nebraska Department of Roads (NDOR) engineers. This bridge system currently accounts for over 110 bridges in Nebraska used for both state highways and local county roads. Excessive transverse and longitudinal deck cracking has been observed and noted in numerous bridge inspection reports. Since the IT girder bridge system is relatively new, limited data and knowledge exist on its structural performance and behavior. This study evaluates the IT girder bridge system by conducting twenty field observations as well as recording accelerometer time …

Investigation Of Rapid Remote Sensing Techniques For Forensic Wind Analyses, Yijun Liao, Richard L. Wood, Mohammad Ebrahim Mohammadi, Peter J. Hughes, J. Arn Womble

Department of Civil and Environmental Engineering: Faculty Publications

Perishable damage data resulting from severe windstorms require efficient and rapid field collection techniques. Such datasets permit forensic damage investigations and characterization of civil infrastructure. Ultimately, observed structural damage serves as a proxy approach to estimate wind speeds for storms that include hurricanes, tornadoes, straight-line winds, etc. One of the more common methods to collect, preserve, and reconstruct three-dimensional damage scenes is the use of an unmanned aerial system (UAS), commonly known as a drone. Onboard photographic payloads permit scene reconstruction via structure-from-motion; however, such approaches often require direct site access and survey points for accurate results, which limit its …

Behavior Of Cold-Formed Steel Metal Industrial Buildings, Adrianna M. Early, Mohammad Ebrahim Mohammadi, Richard L. Wood, Kara D. Peterma

Department of Civil and Environmental Engineering: Faculty Publications

This paper presents research focused on understanding the observed behavior of cold-formed steel (CFS) metal buildings during Hurricane Harvey, which made landfall Friday, August 25, 2017 between Port Aransas and Port O’Connor, Texas. Through the Geotechnical Extreme Event Reconnaissance (GEER) association (funded by the National Science Foundation) a team of structural engineers and researchers performed rapid and detailed assessments of structural damage caused by the hurricane. The National Science Foundation gathered photographs, damage assessments sheets, and three-dimensional laser point cloud data of severely damaged cold-formed steel industrial buildings. The Port Aransas County Airport experienced severe damage to several cold-formed steel …

Post-Earthquake Structural Damage Assessment Through Point Cloud Data, Mohammad Ebrahim Mohammadi, Richard L. Wood

Department of Civil and Environmental Engineering: Faculty Publications

Structural damage assessment following an extreme event can provide valuable information and insight into unanticipated damage and failure modes to improve design philosophies and design codes as well as reduce vulnerability. Oftentimes, structural engineers create finite element models (FEM) of the structure in which numerous model parameters require calibration to simulate the current state. This information may include structural plan details (geometry), material characteristics (strength and stiffness parameters), as well as observed damage patterns (cracks, spalling, etc.). Ground-based lidar (GBL) scans and Structure-from-Motion (SfM) can rapidly capture dimensionally accurate point clouds of the structure or facility of interest. Furthermore, point …

Damage Assessment Of Built-Up Areas Via Uas-Sfm Derived Point Cloud Data, Mohammad Ebrahim Mohammadi, Richard L. Wood

Department of Civil and Environmental Engineering: Faculty Publications

In the aftermath of extreme events (e.g., earthquakes, tsunami, tornados, etc.), rapid and reliable identification of the damage in a built-up area are crucial in to rescue, recovery, and reconstruction operations. While it is critical to conduct efficient emergency response management, lack of classified or tagged damaged regions due to communications and accessibility limitations can further delay recovery operations, rescue efforts, and resource management. Furthermore, critical and perishable damage scenes can also be lost during recovery and cleanup operations immediately following the event. In recent decades, advances in remote sensing technologies demonstrate a great potential to perform rapid reconnaissance and …

Impact-Resistant Behavior Of Reinforced Concrete Bridge Columns, Chen Fang

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The damage caused by a vehicle collision on a pier column can be catastrophic for the functionality of a bridge, even a total collapse of the bridge. ❖ A vehicle collision and a subsequent vehicle blast cause more damages on the bridge. ❖ Limited researches have been conducted to investigate the behavior of the bridge subjected to the combined effect of vehicle collision and blast. ❖ It is necessary to analyze the responses of the bridge under the vehicle collision and blast and provide some design suggestions to strengthen the bridge.

Conclusions ❖ The finite element models including column, pile …

Optimizing Steel Railway Truss Bridge Health Monitoring, Ahmed Rageh, Daniel Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Problems - Steel Railway Trusses • Aging • Large system – bridge AND railway • Labor intensive condition eval • Reported conditions: Stringer-to-floor beam connections [Haghani 2012] Stringer flange clip angle cracks [Haghani 2012] Unequal eyebars stress distribution [DelGrego 2008] Displaced eyebar pins [DelGrego 2008

Problems – Condition Evaluation • Visual inspection: Prescribed frequency Costly Subjected to human interpretation • Sensors: Focused on a single bridge Extensive array Costly

Hyperelastic Structural Fuses For Steel Buildings, Francys López

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Why to upgrade traditional systems?

The FEMA P-58-1 listed some of the limitations in present-generation procedures:

Questions regarding the accuracy and reliability of available analytical procedures in predicting actual building response.

“High” level of conservatism underlying the acceptance criteria.

Inability to reliably and economically apply performance-based procedures to the design of new buildings; and Lack of alternative ways of communicating performance to stakeholders that is more meaningful and useful for decision making purposes.

Performance based design (PBD) emerges as the methodology aiming to bridge this gap, raising the design level performance from life safety (traditional systems) to keep structures fully …

Influence Of Skew And Nonlinear Deck On Elastic Versus Inelastic Distribution Behavior And Ultimate Capacity Of Steel Girder Bridges, Fayaz Sofi, Joshua Steelman

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Research Objectives

• Assessment of alternative load distribution methodologies for potential discrepancies that arise when evaluating distribution behavior of skewed steel girder bridges.

• Investigate the influence of skew and material nonlinearities (concrete cracking and steel yielding) on

• Load distribution behavior (elastic versus inelastic).

• System capacities (yielding and ultimate).

Summary and Conclusions • Influence of skew was examined on load distribution behavior, and nonlinear system-based capacities (yielding and ultimate) of composite steel girder bridges in presence of full material nonlinearities. In addition, assessment of two general definitions (beam-line and response fraction approaches) for quantifying load distribution behavior was …