Structural Engineering Commons^™

Program Progress Performance Report #4, Missouri University Of Science And Technology. Inspire - University Transportation Center

Semi-Annual Progress Reports

No abstract provided.

Strength Of Steel-To-Steel Screw Connections -- Update To Provisions, Thomas Stevens, Thomas Sputo, Jennifer Bridge

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The objective of this project is to review the existing provisions of the AISI S100-16 North American Specification for Cold-Formed Steel Structural Members, for screw connections loaded in shear and tension (but not combined actions). A recent study by the Steel Deck Institute (Sputo 2017) revealed possible unconservative results for screw pull-over, particularly in thinner sheets and/or lower ductility.

This study performed a comprehensive analysis of available steel-to-steel screw connection strength test data, totaling 702 shear tests, 143 pull-over tests, and 335 pull-out tests. The tested strength of these connections was compared to the predicted strength from the existing …

Battery-Free Wireless Strain Measurement Using An Antenna Sensor, Yang Wang

INSPIRE Archived Webinars

A battery-free antenna sensor can wirelessly measure strain on a structure. Bonded to the surface of a base structure, the antenna sensor deforms when the structure is under strain, causing the antenna’s electromagnetic resonance frequency to change. This resonance frequency change can be wirelessly interrogated and recorded by a reader through electromagnetic backscattering. A radio frequency identification (RFID) chip on the sensor harnesses a small amount of energy from the interrogation signal and responds to the reader. The resonance frequency change identified by the reader is then used to determine the strain applied on the structure. The latest antenna sensor …

Flexural Behavior Of Hybrid Composite Beam (Hcb) Bridges, Mohamed A. Aboelseoud, John J. Myers

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A new hybrid composite beam (HCB) has recently been used in the construction of three bridges in Missouri, USA. HCB consists of self-consolidating concrete (SCC) that is poured into classical arch shape and tied at the ends by steel tendons. Both the concrete and the steel are tucked inside a durable fiberglass shell, and the voids are filled with polyiso foam. This paper aims to examine the flexural behavior of an in-service HCB, evaluate the current methodology and assumptions, and propose modifications to that methodology. To achieve these goals, the strains induced in HCB elements due to different loading stages …

Probabilistic Seismic Demand Analysis Of A Bridge With Unbonded, Post-Tensioned, Concrete-Filled, Fiber-Reinforced Polymer Tube Columns, Manisha Rai, Mohamed Elgawady, Adrian Rodriguez-Marek

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Ground motions at sites close to a fault are sometimes affected by forward directivity, where the rupture energy arrives at the site in a form of a very short duration pulse. These pulses impose a heavy demand on structures located in the vicinity of the fault. In this research, a probabilistic seismic demand analysis (PSDA) for a self-centering bridge is carried out. The bridge columns consisted of unbonded, post-tensioned, concrete-filled, fiber-reinforced polymer tubes. A bridge model was developed and non-linear time history analyses were performed. Three different methodologies that used spectral accelerations to predict structural responses were used, and a …

Mechanism Of Tricalcium Silicate Hydration In The Presence Of Polycarboxylate Polymers, Rachel Cook, Hongyan Ma, Aditya Kumar

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Abstract: The early-age hydration of cement is inhibited in the presence of comb-shaped polycarboxylate ether (PCE) polymer -- a dispersant commonly added to control rheological properties of fresh cement paste. This study employs a series of microcalorimetry experiments and phase boundary nucleation and growth simulations to elucidate the effects of dosage and molecular architecture of PCE on hydration of tricalcium silicate (Ca₃SiO₅ or C₃S in cement notation), the dominant phase in cement. Results show that PCE -- regardless of its molecular architecture -- suppresses early-age hydration of C₃S. PCE-induced retardation becomes increasingly more …

Review Of Fiber Optic Sensors For Structural Fire Engineering, Yi Bao, Ying Huang, Matthew S. Hoehler, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Reliable and accurate measurements of temperature and strain in structures subjected to fire can be difficult to obtain using traditional sensing technologies based on electrical signals. Fiber optic sensors, which are based on light signals, solve many of the problems of monitoring structures in high temperature environments; however, they present their own challenges. This paper, which is intended for structural engineers new to fiber optic sensors, reviews various fiber optic sensors that have been used to make measurements in structure fires, including the sensing principles, fabrication, key characteristics, and recently-reported applications. Three categories of fiber optic sensors are reviewed: Grating-based …

Inspire Newsletter Spring 2019, Missouri University Of Science And Technology. Inspire - University Transportation Center

INSPIRE Newsletters

No abstract provided.

Inspire Newsletter Fall 2019, Missouri University Of Science And Technology. Inspire - University Transportation Center

INSPIRE Newsletters

No abstract provided.

In Situ Mechanical Characterization Of The Mixed- Mode Fracture Strength Of The Cu/Si Interface For Tsv Structures, Chenglin Wu, Congjie Wei, Yanxiao Li

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In situ nanoindentation experiments have been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiments in the characterization of nonlinear material properties of 3D integrated microelectronic devices using the through-silicon via (TSV) technique. The elastic, plastic, and interfacial fracture behavior of the copper via and matrix via interface were characterized using small-scale specimens prepared with a focused ion beam (FIB) and nanoindentation experiments. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7° to 83.7°. The mixed-mode fracture strengths were extracted …

Long Period Fiber Grating, Thin Coating Of Graphene And Silver Nanowires, And Corrosion Sensing For Life-Cycle Assessment Of Steel Structures, Chuanrui Guo

Doctoral Dissertations

"This study aims to develop and validate a compact, integrated lab-on-sensor system for simultaneous measurement of strain, temperature and corrosion-induced mass loss in steel structures and concrete reinforcement elements in order to assess their life-cycle performance. The sensing system operates based on the principle of long period fiber gratings (LPFG) that are responsive to both thermal and mechanical deformation, and the change in refractive index of any medium surrounding the optical fiber. To fabricate a LPFG sensor for strain and temperature measurement, a CO₂ laser aided fiber grating system was assembled. To enable mass loss measurement, a low pressure …

Influence Of Pumping Parameters On The Freeze-Thaw And Scaling Resistance Of Highly Workable Concrete, Alexandra Nicole Wehar

Masters Theses

“Over the past 60 years, pumping concrete has gained popularity due to the economic and technical benefits that typically accompanies it. However, boom configuration and flow rate can adversely affect freeze-thaw and scaling resistance of concrete due to the effects of pressure on the air-void system. Therefore, the objective of this research is to assess the influence of different pumping parameters on the durability of hardened self-consolidating concrete. Self-consolidating, flowable, and conventional concrete mixtures were tested during large scale pumping experiments positioning the pump boom in an “A” and a flat shape as well as using different pumping speeds. In …

Design And Performance Of Fiber-Reinforced Concrete With Adapted Rheology For Construction And Repair Of Bridge Structures, Ahmed Abdelrazik

Doctoral Dissertations

“The objective of this document is to design high-performance fiber-reinforced self-consolidating concrete (FR-SCC) for infrastructure repair and fiber-reinforced super-workable concrete (FR-SWC) for bridge construction. The investigated fibers included propylene synthetic fibers, hooked steel fibers, double and triple hooked steel fibers, hybrid crimped steel fiber and polypropylene multifilament fibers, and micro-macro steel fibers. The fiber volume varied between 0 and 0.75%. An expansive agent (EA) was incorporated to compensate for shrinkage and induce compression in the concrete at early age. Two types of EA (G and K) were employed at 0 to 8%, by mass of binder. The investigated FRSCC and …

The Effects Of Silica On The Properties Of Vitreous Enamels, Signo Tadeu Dos Reis, Mike Koenigstein, Liang Fan, Genda Chen, Luka Pavic, Andrea Mogus-Milankovic

Materials Science and Engineering Faculty Research & Creative Works

Ground coat enamels for low carbon steel that contain silica as a mill addition have been developed to study the changes of their properties. Acid-resistant commercial enamel where silica addition was varied from 0 to 10.0 wt % was used for this investigation. The effects of the addition on the corrosion resistance, thermal properties, electrical properties, and mechanical adherence of the enamel to low carbon steel were studied. The corrosion resistance of the steel enameled coupons was tested using a salt spray (fog) apparatus for time periods reaching 168 h at room temperature. It was found that, although the density …

A Threshold To Utilize Guayule Resin As A New Binder In Flexible Pavement Industry, Ahmed Hemida, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study denotes a threshold to utilize Guayule Resin as a new bio-based binder or asphalt cement (AC) proportion, both with/out crumb rubber modifier (CRM), regarding solutions for environment, cost, and sustainability aspects. Via this research, 15 designated binders will be presented, all of them were tested as unaged and RTFO, whereas eight binders proceeded with PAV. Superpave was utilized to study their physical properties. Viscosity was examined upon some guayule-based binders with/out CRM, getting 114cP (at 135℃) for BGR, increased to about 3 times with 10%CRM (by weight of liquid binder) and about 7-8 times with 20%CRM. Comparisons among …

Field Implementation Of Rubberized Chip Seal, Ahmed Gheni, Alireza Pourhassan, Mohamed Elgawady, Yasser Darwish, William P. Schonberg

Civil, Architectural and Environmental Engineering Technical Reports

Chip seals have been widely used as a pavement maintenance surface treatment due to its competitive cost and construction time. Recently, the research team developed a rubberized chip seal where natural aggregate is replaced with crumb rubber obtained from recycled tires. During this study, a total of 108 laboratory specimens and a field chip seal section with different crumb rubber replacement ratios were investigated. Aggregate macrostructure, retention, and skid resistance were measured. The crumb rubber showed a remarkable performance in aggregate retention measured using the Vialit and Pennsylvania tests. The values of the mean texture depth of rubberized chip seal …

The 2017 Aisi Cold-Formed Steel Design Manual, Joshua Buckholt, Helen Chen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The 2017 edition of AISI D100, the Cold-Formed Steel Design Manual (Manual) has been published. Updates to the Manual include: alignment with AISI S100-16, the North-American Specification for the Design of Cold-Formed Steel Structural Members (NA Specification); several new and varied design examples; additional discussions related to the design of cold-formed steel structures and components; and expanded bibliographies of relevant resources. The database of examples illustrating the Direct Strength Method (DSM) and new provisions in the NA Specification has been expanded. Also published with the Manual are the North-American Specification and its Commentary.

Strength Of Cold-Formed Steel Clip Angle In Combined Bending And Shear Loading, Cheng Yu, Zhishan Yan, Wenying Zhang

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Thin-walled cold-formed steel (CFS) clip angles have been commonly used for connecting CFS framing members or attaching CFS members to the major building structure. The implementation of clip angles involves consideration of ultimate strength for combined bending moments and shear forces. Therefore, a test program of CFS clip angle was recently conducted to investigate the behavior and strength of cold-formed steel clip angle subjected to combined bending moments and shear forces at different boundary conditions. The research included connection tests on clip angle. The testing method was adopted from the AISI S914 Test Standard for Joist Connectors Attached to Clod-Formed …

Critical Design Criteria For Standard, Truncated, And Parallel Chords Cold-Formed Steel Trusses, Maelle Van Thienen, Johannes Dimyadi, James B. P. Lim, G. Charles Clifton

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The design of cold-formed steel trusses can be a very complicated and long repetitive process involving up to 28 load combinations added to serviceability checks depending on the design standards being used. This process is particularly tedious if a near optimal solution is required. Additionally, the risk of introducing human errors is usually quite high as it is a process often done by hand. FRAMECAD Structure is a niche software solution born from the desire to provide a complete solution for constructing with cold-formed steel by a company selling roll-forming machines. FRAMECAD Structure specialises on automating the calculations and design …

Cold-Formed Ferritic Stainless Steel Tubular Sections Under End-One-Flange Loading Condition, Hai-Ting Li, Benjamin Young

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper presents experimental and numerical investigations of cold-formed ferritic stainless steel tubular sections under End-One-Flange (EOF) loading condition. A series of web crippling tests was conducted on cold-formed square and rectangular hollow sections of ferritic stainless steel grade EN 1.4003. The web crippling test results were used for the verification of the finite element (FE) model. Upon verification, a parametric study was performed thereafter. The codified web crippling design provisions in American, Australian/New Zealand and European standards for stainless steel structures were assessed. Improved web crippling design rules are proposed for cold-formed ferritic stainless steel tubular sections under EOF …

Optimum Slot Weld Width For Cold-Formed Steel, Emilee A. Martin, Fredrick R. Rutz

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Slot welds can be used for connections in cold-formed steel (CFS) structures. However, structural engineers will find AISI S100, “North American Specification for the Design of Cold-Formed Steel Structural Members” (AISI 2016) - which can be used for guidance in calculating structural capacity of many welds types - silent on this specific application.

Research at the University of Colorado Denver has been directed toward determination of the strength of slot welds in sheet steel. A comprehensive series of tests were performed to determine structural capacity and ductility of various slot weld widths using a metal inert gas (MIG) welding process. …

Wei-Wen Yu International Specialty Conference On Cold-Formed Steel Structures 2018: Recent Research And Developments In Cold-Formed Steel Design And Construction, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.

Low Fatigue Response Of Crest-Fixed Cold-Formed Steel Drape Curved Roof Claddings, Krishanu Roy, James B. P. Lim, Amir Mohammad Yousefi, G. Charles Clifton, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel roof claddings are subjected to significant suction/uplift pressures during high wind events. In New Zealand, the strong prevailing winds makes this a common occurrence. Suction pressures are generated by the turbulence of the wind flow around the building which can vary both spatially and temporally. The weakest link in the roofing system is the connection between roof sheeting and screw fasteners, which if fails, can lead to progressive collapse of the whole roofing assembly. Fluctuating high wind suction pressures can result in either static or fatigue pull-through failure of the roof sheeting at its screw fastener connections. Current …

Stressed Skin Design Of Steel Sheeting Panels – Part 2: Shear Panels With Sheeting Fixed On All 4 Sides, A. M. Wrzesien, James B. P. Lim, I. A. Macleod, R. M. Lawson

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

In this paper, the strength and stiffness of different roof panels were investigated, in order to establish their ability to act as in-plane diaphragms for stressed skin design of cold-formed steel portal frames. A total of 6 roof panels, approximately 3 x 3m, were examined by testing with sheeting profiles fixed on 4 sides. A variety of sheeting profiles in two industry standard thicknesses of 0.5 and 0.7mm were tested, all using top-hat shaped purlins fixed with self-drilling, self-tapping screws. The experimental strength and stiffness of each panel were then compared against existing design methods. The Finite Element Analysis (FEA) …

Computational Modeling Of Joist-To-Ledger Connections In Cold-Formed Steel Diaphragms, Hernan Castaneda, M. Eng, Kara D. Peterson

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel framed buildings can involve a range of options for framing systems, including balloon framing, platform framing, and ledger framing. Transfer of lateral forces from the diaphragms to the wall system (and ultimately to the ground) depends on the interactions within the wall-diaphragm connection, which is dependent on choice of framing system. In ledger framing, floor joists are hung from top of wall studs via a rim track (ledger) and clip angle connection. Recent experimental efforts at Johns Hopkins University studied the wall-diaphragm connection with the goal of quantifying its contribution to overall diaphragm response. Results from these experiments …

Effect Of Connection Details On The Cyclic Behavior Of Nestable Screw Sidelaps, S. Torabian, H. Folk, Benjamin W. Schafer

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The connection strength and stiffness sensitivity of screwed sidelaps in nestable steel decks to screw installation details has been experimentally explored via cyclic testing. The cyclic behavior of sidelaps has been recently incorporated in the high fidelity modeling and seismic evaluation of the steel deck diaphragm in rigid wall - flexible diaphragm buildings, where “unzipping” a sidelap (loss of a significant number of sidelap connections along a deck edge) could significantly reduce the seismic performance of the whole diaphragm. A total of 24 monotonic and cyclic sidelap tests have been performed in the Thin-Walled Structures Laboratory at Johns Hopkins University. …

Fire Resistance Of Cavity Insulated Light Gauge Steel Framed Walls, Anthony Deloge Ariyanayagam, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Light-gauge steel framed (LSF) wall systems are made of cold-formed steel studs and tracks and lined with gypsum plasterboards. They are mostly cavity insulated to provide acoustic and thermal performance. Cavity insulation delays the temperature rise across the wall as it restrains the heat transfer. This delays the ambient plasterboard surface temperature rise and thus improves the insulation failure time of LSF walls. However, LSF walls are also used as load bearing walls. Having cavity insulation causes the fire side temperatures to increase rapidly, resulting in a higher temperature gradient across the stud depth. This leads to higher thermal bowing …

Shake Table Testing For Seismic Response Evaluation Of Cold-Formed Steel-Framed Nonstructural Architectural Components, Luigi Fiorino, Bianca Bucciero, Tatiana Pali, Ornella Iuorio, Raffaele Landolfo

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The seismic response evaluation of cold-formed steel-framed nonstructural architectural components was investigated in an experimental campaign carried out within of the research study agreement between Knauf Gips KG and the Department of Structures for Engineering and Architecture of the University of Naples “Federico II”. The main objective of this research was to investigate the seismic performance of drywall nonstructural systems, i.e. cold-formed steel-framed indoor partition walls, outdoor façade walls and suspended ceilings. The present paper deals with the dynamic shake table tests. The tests were carried out on two different typologies of prototypes (Type 1 and Type 2) for a …

Numerical Simulation Of The Thermal And Mechanical Behavior Of Cold-Formed Steel Composite Floor Under Fire Conditions, Jixian Peng, Wei Chen, Jihong Ye, Zhengliu Wang

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel (CFS) building structures are generally acknowledged as green and industrialized buildings, and the fire resistance behavior has become an important issue. Previous studies were mainly to investigate the fire performance of load-bearing CFS walls lined with different panels. Based on the finite element (FE) software package, ABAQUS, this paper presented a numerical simulation on a new CFS channel joist – ALC (autoclaved lightweight concrete) composite floor under fire conditions. Finally, the present numerical simulation of CFS composite floor in fire was compared with previous full-scaled fire experiments of such floors. The results showed that the temperature progression of …

New Web Crippling Design Rules For Cold-Formed Steel Beams, L. Sundararajah, M. Mahendran, P. Keerthan

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Lipped channel beams (LCBs) and SupaCee sections are commonly used as floor joists and bearers in the construction industry. SupaCee section is one of the cold-formed steel members, which is increasingly used in the building construction sector. It is characterized by unique ribbed web and curved lip elements, and is claimed to be more economical with extra strength than the traditional channel sections. These thin-walled LCBs and SupaCee sections are subjected to specific local and global failures, one of them being web crippling. Several experimental and numerical studies have been conducted in the past to study the web crippling behaviour …