Structural Engineering Commons^™

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

College of Graduate Studies: Theses & Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

Characterization And Modeling Of Asphalt Concrete For Dynamic Properties And Performances, A S M A. Rahman

Civil Engineering ETDs

The recently developed mechanistic-empirical pavement design guide (MEPDG, also known as Pavement M-E design method) uses the nationally calibrated, binder viscosity-based dynamic modulus predictive model for the design and analysis of asphalt pavements. In this study, this model is assessed for its appropriateness for asphalt-aggregate mixtures typically used in New Mexico. In essence, this study investigates the predictability issue of complex modulus of New Mexico mixes. A total of 54 Superpave mixes with different aggregate gradations, air voids, and binder grades were collected from the mixing plants and from the pavement construction sites. The loose asphalt mixtures were then compacted, …

Using Historic Pavement Performance Data To Identify And Select Sites For Asphalt Mixture Design Studies, Allyson Richey

Civil Engineering Undergraduate Honors Theses

Since 1997 Arkansas asphalt mixtures have been designed using a procedure commonly known as ‘Superpave’. In a traditional Superpave mix design, the design considers only traditional volumetric parameters; however, recent advances in mix design technology emphasize mixture’s ability to perform in its environment. There are numerous factors which affect the performance characteristics of an asphalt mix. Certainly, the asphalt binder’s performance is a critical variable in this system. Asphalt binders are sensitive to temperature, so much so that their primary parameter on which they are recommended is a function of both temperature and the geographic latitude in which the pavement …

Bridge Build, Andrew Little

Student Scholarship

Bridge build design that includes not only a building process, but a research paper to make the best build possible as well.

An Enhanced Bridge Weigh-In-Motion Methodology And A Bayesian Framework For Predicting Extreme Traffic Load Effects Of Bridges, Yang Yu

LSU Doctoral Dissertations

In the past few decades, the rapid growth of traffic volume and weight, and the aging of transportation infrastructures have raised serious concerns over transportation safety. Under these circumstances, vehicle overweight enforcement and bridge condition assessment through structural health monitoring (SHM) have become critical to the protection of the safety of the public and transportation infrastructures. The main objectives of this dissertation are to: (1) develop an enhanced bridge weigh-in-motion (BWIM) methodology that can be integrated into the SHM system for overweight enforcement and monitoring traffic loading; (2) present a Bayesian framework to predict the extreme traffic load effects (LEs) …

Schedule And Cost Performance Analysis And Prediction In Louisiana Dotd, Mahmoud Hamide

LSU New Orleans Theses and Dissertations

Many construction projects in the United States are facing the risk of cost overrun and schedule delays. This is also happening here in the State of Louisiana. When these things happen, it causes cost overrun which can then be passed on to the tax payers and may also cause the state to take on less projects than they normal. Many researchers have studied the reasons behind both the cost overrun and the delays resulting in private firms, developing project management tools and best practices to prevent this risk. In this research, I aim to study the historical trend in 2912 …

Evaluating The Impact Of Different Types Of Stabilized Bases On The Overall Performance Of Flexible Pavements, Andrae Anthony Francois

Theses and Dissertations

This study was initiated with the aim of evaluating the impact of stabilized and untreated base layers on the performance (i.e., fatigue and rutting) of flexible pavements. Four field sections constructed using stabilized base layers (i.e., bituminous (asphalt emulsion), calcium chloride (CaCl-2), Portland cement, and geogrid stabilized base layers) and a control section constructed using untreated RAP aggregates were analyzed in this study. Falling Weight Deflectometer (FWD) tests were conducted on all the field sections and the collected data was used to backcalculate the elastic moduli for all layers. The influence of the stabilized bases and the untreated RAP base …

Optimizing Steel Railway Truss Bridge Health Monitoring, Ahmed Rageh, Daniel Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Problems - Steel Railway Trusses • Aging • Large system – bridge AND railway • Labor intensive condition eval • Reported conditions: Stringer-to-floor beam connections [Haghani 2012] Stringer flange clip angle cracks [Haghani 2012] Unequal eyebars stress distribution [DelGrego 2008] Displaced eyebar pins [DelGrego 2008

Problems – Condition Evaluation • Visual inspection: Prescribed frequency Costly Subjected to human interpretation • Sensors: Focused on a single bridge Extensive array Costly

Evaluation Of Protection Of Frp Wrap On Bridge Piers From Corrosive Effects Of Snow And Ice Chemicals, Lizzie Miller

Honors Theses

Highway bridge components, such as decks and piers, are structures that are often exposed to chlorine-heavy chemicals. Corrosion of rebar, one of the main contributors to structural deficiencies in highway bridges, is largely caused by chloride contamination from exposure to deicing salts and chemicals. Current forms of external protection to highway bridge piers include paint coatings, shells, and wraps. This thesis will focus on the protective capabilities that Fiber Reinforced Polymer (FRP) wraps could provide to bridge piers. ASTM C666 was utilized to recreate environmental conditions, during which concrete samples were exposed to calcium chloride. ASTM C1760-12 was utilized to …

Influence Of Skew And Nonlinear Deck On Elastic Versus Inelastic Distribution Behavior And Ultimate Capacity Of Steel Girder Bridges, Fayaz Sofi, Joshua Steelman

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Research Objectives

• Assessment of alternative load distribution methodologies for potential discrepancies that arise when evaluating distribution behavior of skewed steel girder bridges.

• Investigate the influence of skew and material nonlinearities (concrete cracking and steel yielding) on

• Load distribution behavior (elastic versus inelastic).

• System capacities (yielding and ultimate).

Summary and Conclusions • Influence of skew was examined on load distribution behavior, and nonlinear system-based capacities (yielding and ultimate) of composite steel girder bridges in presence of full material nonlinearities. In addition, assessment of two general definitions (beam-line and response fraction approaches) for quantifying load distribution behavior was …

Practical Considerations In Determining Timber Pile Depth Using The Sonic Echo Method, Ali F. Jwary

Civil Engineering ETDs

The Federal Highway Administration indicates that about 85,000 bridges in the United States have no original contract documents with information about the type, depth, geometry and material of their foundations (FHWA, 2010). Furthermore, the National Bridge Inventory (NBI) provides information about 86,133 bridges nationwide that are rated as scour critical because of unknown foundation condition. In New Mexico, there are more than 281 bridges with unknown foundations, which are owned by the New Mexico Department of Transportation; 71 of these are timber bridges. These data indicate a serious problem that needs decisive action to assess the unknown bridge foundation characteristics …

Bicp Global Bim Study - Lessons For Ireland’S Bim Programme, Barry Mcauley, Alan Hore, Roger West

Reports

The Construction IT Alliance (CitA) has been promoting the benefits of digitisation in the construction and engineering industry in Ireland since its formation back in 2002. Whilst the Alliance has always strived to ensure that its members are exposed to a wide spectrum of contemporary digital tools and processes, the concept of Building Information Modelling (BIM) has dominated the focus of its activities over the past five years.

BIM can be described as a digital tool that facilitates everybody to better understand a building or structure through the use of a digital model which draws on a range of data …

Air Injection As A Scour Countermeasure At Bridge Piers, Ravi Teja Reddy Tippireddy

Dissertations, Master's Theses and Master's Reports

Local scour is a major cause of concern for the stability of bridge piers and the safety of the public using the bridges. Structural countermeasures and flow-altering devices have been developed to deal with local scour. Many armoring structural countermeasures are very effective and efficient in clear water conditions but are susceptible to moving bed forms and leaching. The flow-altering devices are effective in both clear water conditions and moving bed forms, but are prone to clogging, less efficient in changing flow direction, etc. This study aims to reduce the local scour by injecting air in order to reduce the …

Uav-Based Bridge Inspection And Computational Simulations, Luis Duque

Electronic Theses and Dissertations

The use of Unmanned Aerial Vehicles (UAV), commonly known as drones, has significantly increased in the field of civil engineering due to the poor condition of the United States’ infrastructure. The American Society of Civil Engineers (ASCE) recently reported that more than 9.1% of the United States’ bridges were structurally deficient and required attention and maintenance to ensure appropriate structural performance. Meanwhile, current practices are expensive and unsafe for bridge inspectors, requiring innovative and safer methods for the study of bridges. The goal of this paper was to identify better techniques to not only inspect, quantify, and determine the effect …

Condition Factor Calibration For Load And Resistance Factor Rating Of Steel Girder Bridges, Pranav M. Shakya

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The Load and Resistance Factor Rating (LRFR) is a reliability-based rating procedure complementary to the Load and Resistance Factor Design (LRFD). The intent of LRFR is to provide consistent reliability for all bridges regardless of in-situ condition. The primary difference between design and rating is the uncertain severity and location of deterioration, including the potential future loss of strength for an element already evidencing deterioration. Ostensibly, these uncertainties are accounted for by applying an additional strength reduction factor: the condition factor, ϕ_c. Currently, condition factors are nominally correlated to the condition of the member, which can be Good, …

Chloride Contamination Remediation On Steel Bridges, Bobby W. Meade, Christopher Goff, Sudhir Palle, Theodore Hopwood Ii

Kentucky Transportation Center Research Report

Researchers evaluated 32 steel surface preparation methods to determine how effectively they remove chloride from corroded chloride-contaminated steel panels. Wet methods proved more effective than dry methods. The three most effective wet methods injected mineral slag abrasives in a water stream and resulted in less than 1% chlorides remaining. Most dry surface preparation methods left significantly more chloride contamination after surface preparation. The three most effective dry methods used multiple blast cleaning cycles. These methods approached the effectiveness of the best wet methods, with 1.6 to 2.0% chlorides remaining. The least effective surface preparation was a single abrasive blast cleaning …

Efficient Domain Decomposition Algorithms And Applications In Transportation And Structural Engineering, Paul W. Johnson Iii

Civil & Environmental Engineering Theses & Dissertations

Domain decomposition is a divide-and-conquer strategy. In the first part of this dissertation, a new/simple/efficient domain decomposition partitioning algorithm is proposed to break a large domain into smaller sub-domains, in such a way as to minimize the number of system boundary nodes and to balance the work load for each sub-domain. This new domain decomposition algorithm is based on the network’s shortest path solution. Numerical results indicate that the new Shortest Distance Decomposition Algorithm outperformed the most widely used METIS algorithm in 21 out of 27 tested (transportation) examples. In the second part of this dissertation, another new/simple and highly …

Evaluation Of The Use Of Painted And Unpainted Weathering Steel On Bridges, Theodore Hopwood Ii, Sudhir Palle, Bobby W. Meade, Rick Younce

Kentucky Transportation Center Research Report

KTC researchers studied the use of unpainted weathering steel on bridges, using findings of inspections performed on Kentucky Transportation Cabinet (KYTC) bridges constructed with both painted and unpainted weathering steel as well as laboratory testing. Laboratory tests were conducted on test panels of conventional and weathering grades of steel to determine the performance of barrier and zinc-based coatings over abrasive-blasted substrates of those steel types in both the new and corroded conditions. The report provides the following recommendations for the use of painted and unpainted weathering steel on Kentucky bridges based upon both the field and laboratory findings:

• KYTC should …

Wildcat Bridge - I-65 Artesion Well/Geotechnical/Structural, Anne Rearick, Jeremy Hunter, Silas Nichols, Mir Zaheer

Purdue Road School

In this session we will discuss the emergency design and repair of the I-65 bridge over Wildcat Creek in Tippecanoe County during the summer of 2015 that closed I-65 northbound.

Storm Damage - Floating Culverts, Dale Sedler, Mark Bailey

Purdue Road School

A review of buoyancy issues culverts experience due to blockage. Includes discussion of blockage due to floating debris and issues with multiple culverts. Provides information on characteristics that help to determine if a culvert has "floated."

State-Of-The-Art Review Of Cathodic Protection For Reinforced Concrete Structures, Aimee Byrne, Niall Holmes, Brian Norton

Articles

Cathodic protection (CP) limits the corrosion of a metal surface by making it the cathode of an electrochemical cell. This can be achieved either by using a more active sacrificial anode to create a driving current, or by using inert anodes and impressing a current onto the cathode surface using an external direct current (DC) source. Impressed current cathodic protection (ICCP) is preferred where widespread protection is required, particularly in reinforced concrete structures. ICCP needs a constant DC power supply that is usually provided through a grid connection or independent generators. This paper presents the currently available CP systems for …

Precast Full-Depth Deck Panels Supported On Inverted Bulb-Tee Bridge Girders, Michael James Mingo

Electronic Theses and Dissertations

The South Dakota Department of Transportation (SDDOT) currently uses precast double-tee bridge deck systems for many of its county bridges because they are economical and fast in construction. Current bridges are designed for a service life of 75 years. However, many double-tee girder bridges are deteriorating and some need total replacement after 40 years in service. Furthermore, the double-tee bridge system only has one supplier in South Dakota. Alternative durable precast or prefabricated bridge systems are needed to provide more options to local governments when designing a new bridge. Different alternatives will also give local governments more flexibility to select …

Role Of Soil Parameters On Loading Of Buried Structures, Xiao Zhang, Mark D. Bowman, Rafael R. Armendariz Briones

The Summer Undergraduate Research Fellowship (SURF) Symposium

Load rating is the process to evaluate and explore the structural capacity of bridges as much as possible within safety range. As a balance between economy and safety, proper load ratings save money and keep public safe. Knowing the contribution and interaction of each different soil parameter on the loading can significantly reduce the amount of work when load rating those structures. However, for buried structures without plans, such contribution or interaction is never known. This parametric study explores how much each soil parameter of three types of soils can affect the loading of buried structures without plans. An existing …

Bulbous Pier: Alternative To Bridge Pier Extensions, Amilcar Chavez

UNLV Theses, Dissertations, Professional Papers, and Capstones

Bridge deck splashing causes deterioration to the bridge structure and renders the bridge unsafe for motorist and pedestrians. The traditional countermeasure for bridge deck splashing is pier extension, the pier extension moves the pier wave away from the bridge deck, but retrofitting existing bridges with pier extensions is costly. This research proposes the bulbous pier concept as an alternative to pier extension.

The decrease in the pier wave produced by the bulb is due to energy subtracted by the bulb via two forces, the viscous resistance, and the wave-making resistance. The proposed mathematical model for the bulbous pier design follows …

Senior Design: Proposed Stem Academic Building, Middlesex Community College, Senior Design Class

Civil Engineering Student Work

2015 Civil Engineering Senior Design Project.

A proposal for a new STEM building to be constructed on the Middlesex Community College.

Completed by:

• Abdullah Al Bakri
• Ryan Benoit
• Brittany Brown
• Michael Buraczynski
• Samuel Colangelo
• Joseph Connolly
• Kyle Elmy
• Michael Fischer
• Victor Goitia Jurado
• Michael Hanley
• Andrew Malian
• Michael Mathews
• Dionys Quezada
• Katie Rougeot
• Jacob Santos
• Isadora Sartor
• Vega Yerko

Influence Of Spatial Variations Of Railroad Track Stiffness And Material Inclusions On Fatigue Life, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Railroad transportation is very important for economic growth and effective maintenance is one critical factor for its economic sustainability. The high repetitive forces from a moving railcar induce cyclic stresses that lead to rail bending and potential deterioration due to fatigue crack initiation and propagation. Previous research for prediction of fatigue life has been done under the assumptions of a uniform track bed and a homogeneous rail. However the spatial variation of the track stiffness is expected to increase the maximum stresses in the rail and, therefore, accelerate the fatigue process. The research described in this dissertation is focused on …

Effect Of Lateral Stiffness On Bridge Deck Performance, Andrea Del Pilar Toro

UNF Graduate Theses and Dissertations

The use of the empirical deck design method has increased its acceptance due to the economic advantages that it presents when compared to its counterpart, the traditional method. This can be attributed to the fact that the empirical method provides an appropriate design where the deck withstands stress not only due to the steel reinforcement but to an implicit arching membrane stress set-up as an effect of the lateral restraint surrounding the deck slab known as Compressive Membrane Action (CMA).

It has been proved through research that most design codes underestimate the strength of laterally restrained slabs. However, there is …

Testing And Strengthening Bridge Connections, Christopher Higgins, Peter Dusicka, Michael Scott

TREC Project Briefs

Researchers evaluate and improve the strength of gusset plate connections, essential pieces in bridge design that can fail due to buckling.

Heavy Vehicle Performance During Recovery From Forced-Flow Urban Freeway Conditions Due To Incidents, Work Zones And Recurring Congestion, Alexander Drakopoulos, Yue Liu, Alan Horowitz

Civil and Environmental Engineering Faculty Research and Publications

Information contained in the Highway Capacity Manual on the influence heavy vehicles have on freeway traffic operations has been based on few field data collection efforts and relied mostly on traffic simulation efforts. In the 2010 Manual heavy vehicle impact is evaluated based on “passenger car equivalent” values for buses, recreational vehicles and trucks. These values were calibrated for relatively uncongested freeway conditions (levels of service A through C) since inadequate field data on heavy vehicle behavior under congested conditions were available. A number of field data collection efforts, that were not included in deriving the passenger car equivalent values …

Structural Reliability Analysis Of Corroded Steel Girder Bridge, Mohammed Shaalan Al Badran

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The natural aging, environmental impact, and appropriate design are certainly playing a serious role in safety of the bridges function. The functional safety of bridge constitutes a prime element of the transportation system serving commuters, passengers and freight. According to Federal Highway Administration, the steel bridges share represents a large amount of the United States’ bridges. In last century, the collapse of both the Silver Bridge at Point Pleasant, West Virginia over the Ohio River on December 15, 1967 and over the Mianus River Bridge in Connecticut on June 28, 1983 showed that steel corrosion has been the leading reason …