Structural Engineering Commons^™

Winter Maintenance On The Irish Road Network, Hugh Mcconnell, Brian Mccann

Civil Engineering Research in Ireland 2020

Winter maintenance relates to those activities undertaken where the objective is to minimise the impact of frost, ice or snow on the travelling public. The responsibility for winter maintenance of all roads in Ireland currently rests with local authorities and Transport Infrastructure Ireland (TII) (Formerly the NRA) on behalf of the Department of Transport, Tourism and Sport (DTTaS), (DTTaS, 2017). The aim of the study was to examine current winter maintenance practices undertaken in Ireland by local authorities and the Motorway Maintenance and Renewals Contracts (MMaRC) contractors and examine the potential financial, operational and environmental benefits if pre-wet and brine …

Modelling The Thermal Behaviour Of A Precast Pcm Enhanced Concrete Cladding Panel, Dervilla Niall, Roger P. West, Oliver Kinnane, Richard Hegarty

Civil Engineering Research in Ireland 2020

According to the World Business Council for Sustainable Development there is currently a stock of more than 80 million buildings in Europe built between 1950 and 1975, a period during which energy performance was not considered in building design. To enable governments to comply with the European Directive 2010/31/EU on the energy performance of buildings, strategies are required to improve the energy efficiency of these buildings. Using the mass of a building to store or dissipate heat can reduce the demand on the auxiliary heating and/or cooling systems and hence reduce the overall energy demand of the building.

Previous research …

Analysis And Design Of A Novel Heavy-Duty Precast Element, Daniel Naughton, Michael Naughton, Michael O'Sullivan, Suhaib Salawdeh

Civil Engineering Research in Ireland 2020

Window sills are common to most buildings. In Ireland, concrete is the most popular material used for external sills. A standard one-metre concrete window sill weighs about 70kg. While external window sills are required to have sufficient capacity to resist damage during transportation and loading, they are non-structural elements. Therefore, there is no need for their high selfweight. This project looks to redesign concrete window sills to make them lighter. Decreasing the amount of concrete used in each sill would significantly reduce their self-weight. This would make concrete window sills more manageable in terms of transportation and installation. Two design …

Development And Localisation Of Ultra High Performance Concrete Using A Particle Packing Model, William Wilson, Tomas O'Flaherty

Civil Engineering Research in Ireland 2020

Ultra-high performance fibre reinforced concrete (UHPFRC) is used worldwide to improve the structural performance of infrastructure such as bridges, extend their working life and reduce environmental impact. As a result thinner structures are constructed leading to reductions in the structure’s self-weight and the volume of concrete and natural raw aggregates used in their construction. A drawback to UHPFRC is that it results in a significant rise in initial costs over normal and even high performance concretes, and it has very high binder contents, which in some cases is greater than 1100kg/m³. Therefore, the cost-efficiency and sustainability of this …

Composite Behaviour Of Wide Sandwich Panels With High Performance Concrete Thin Wythes With And Without Thermomass Shear Connectors, Jagoda Lipczynska, Roger P. West, Michael Grimes, Dervilla Niall, Oliver Kinnane, Richard Hegarty

Civil Engineering Research in Ireland 2020

To partly address the future sustainability of energy use in buildings, there is a program in Europe to retrofit domestic and commercial buildings with non-load bearing insulated re-cladding and over-cladding panels. Recent research work has shown that limited composite action is possible depending on the type of non-conductive shear connector and the stiffness of the insulation between the inner and outer wythes. This paper reports on the mix design development to develop high strength 20mm thick wythes and the manufacture of sandwich panels with five silicone-bonded layers of XPS insulation, making up a panel which is 220mm thick. These model …

Examining The Effects Of Reducing The Cement Content Of Portland Cement Concrete Pavement, Bryan Casillas

Graduate Theses and Dissertations

Portland cement is a significant component in a concrete mixture. For concrete used in portland cement concrete pavement (PCCP), the Arkansas Department of Transportation (ARDOT) specifies a minimum cementitious material content of 564 lb/yd3 and a maximum water-cementitious material ratio of 0.45. Prior research conducted at the University of Arkansas, TRC 0603, indicated concrete mixtures used in five bridge decks throughout Arkansas achieved the required 28-day strength at seven days, and the measured compressive strength at 28 days was 30% greater than required. The use of high strength concrete in pavements throughout the state can increase cracking and consequently reduce …

Verifying The Calcium Oxychloride Threshold In Cementitious Pastes, Fatoumata Traore

Graduate Theses and Dissertations

Calcium oxychloride (CAOXY) formation is a serious deterioration mechanism known to cause joint damage in concrete pavements. CAOXY is the product of a chemical reaction between calcium chloride (CaCl2) or magnesium chloride (MgCl) deicing salts and calcium hydroxide in the cementitious matrix. Currently, the accepted CAOXY threshold at which deterioration is mitigated in cementitious paste is 15 g/100 g paste (15 oz/100 oz paste); however, this limit was developed using flexural strength testing. For this investigation, the current threshold was evaluated using compressive strength and mass change over time in paste specimens exposed to CaCl2. Fly ash is used to …

Commodity-Based Freight Activity On Inland Waterways Through The Fusion Of Public Datasets For Multimodal Transportation Planning, Magdalena I. Asborno

Graduate Theses and Dissertations

Within the U.S., the 18.6 billion tons of goods currently moved along the multimodal transportation system are expected to grow 51% by 2045. Most of those goods are transported by roadways. However, several benefits can be realized by shippers and consumers by shifting freight to more efficient modes, such as inland waterways, or adopting a multimodal scheme. To support such freight growth sustainably and efficiently, federal legislation calls for the development of plans, methods, and tools to identify and prioritize future multimodal transportation infrastructure needs. However, given the historical mode-specific approach to freight data collection, analysis, and modeling, challenges remain …

2-D Non-Linear Finite Element Analysis Of Folsom Dam: Seismically Induced Separation And Pore Pressure Along The Soil-Concrete Interface, Grace Amoussou

Master of Science in Civil Engineering Theses

The seismic soil-concrete interface stability of composite dams has been an area of interest to many researchers. However, the true interface behavior during a seismic event has not been well understood. During a ground shaking, bonding and de-bonding action along the interface may cause significant separation of soil and concrete surfaces, and such a separation may take place at any depth along the interface creating a stability concern for the overall dam. Moreover, the repetitive nature of bonding/debonding behavior may induce excess pore pressure along the interface, which in turn, may trigger a liquefaction failure or a hydraulic fracture in …

Understanding Workability In Belitic Calcium Sulfoaluminate Concrete Mixtures, Caleb W. Chesnut

Civil Engineering Undergraduate Honors Theses

Belitic Calcium Sulfoaluminate cement (BCSA) is an emerging technology in the concrete industry. BCSA has similar hardened properties to portland cement (PC) but can set in under 20 minutes and reach 4,000 psi in less than 2 hours. Portland cement accounts for 8% of the world’s CO2 emissions, BCSA cements require less energy to produce. Studies have shown that 40% less CO2 is emitted during the production of BCSA cement than portland cement. This environmental benefit also makes it a very promising PC alternative. Before a new material can be used, designers need to understand the material’s properties. The goal …

Quantitative Resistance Assessment Of Sfrp-Strengthened Rc Bridge Columns Subjected To Blast Loads, Ahmad Alsendi, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

The blast resistance of a typical reinforced concrete bridge pier column design was modeled with a nonlinear finite element approach that considers material damage, fracture, and separation. While varying concrete strength, amount of longitudinal reinforcing steel, and gravity load, the effect of applying an externally bonded steel fiber reinforced polymer (SFRP) wrapping was assessed. The presented approach uniquely quantifies column blast resistance in terms of charge weight. It was found that blast capacity was roughly linearly related to concrete strength and steel reinforcement ratio, the former of which is most influential. It was further found that a single layer of …

Correction To: Recommendations Of Rilem Tc 260-Rsc For Using Superabsorbent Polymers (Sap) For Improving Freeze–Thaw Resistance Of Cement-Based Materials (Materials And Structures, (2019), 52, 4, (75), 10.1617/S11527-019-1375-4), Viktor Mechtcherine, Christof Schröfl, Michaela Reichardt, Agnieszka J. Klemm, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Agnieszka J. Klemm is affiliated to Glasgow Caledonian University, Glasgow, UK.

Railway Bridges Up-To-Date, Stephen Dick

Purdue Road School

Railroad bridges are not foremost on people’s minds, but they are still a critical item in our nation’s infrastructure. The railroads have a major investment in their bridges, and with many beyond 100 years old, maintenance and replacement of them is still a major cost item. This presentation describes the current state of railroad bridges, discusses older and new bridges, and addresses the current regulatory environment.

Bim For Bridges And Structures Pooled Fund Initiative, Julie Rivera, Connor Christian

Purdue Road School

The BIM for Bridges and Structures initiative, also known as TPF-5(372), is a transportation pooled fund project that is a collaborative effort of 20 states, FHWA, and the AASHTO Committee on Bridges and Structures. The pooled fund objective is to develop an open, national standard for exchanging information necessary for the design, fabrication, and construction of bridges and structures in the United States. The presentation will provide an overview of the project and explain ways in which stakeholders can get involved.

Load Rating Of Bridges Without Plans, Rafael Armendariz, Mark Bowman

Purdue Road School

The presentation will address the challenges of load rating bridges without plans and how a four-step procedure can be used to guide the engineer in determining bridge ratings for poorly documented bridges. The procedure is illustrated through the assessment of an earth-en-filled reinforced concrete arch bridge with no available bridge information.

A Look At Indot's Overhead Sign Structures, David Boruff

Purdue Road School

This presentation highlights results of sign sheeting field review and associated changes in policy and standards, as well as how we’re implementing the findings from our overhead sign structure inspection program through the first statewide overhead sign structure repair and replacement contract.

Over Height Impact Avoidance And Incident Detection System, Suvash Chapain, Aly Mousaad Aly

Faculty Publications

During the construction and repair of bridges, work platforms or construction-related containment may result in restricted vertical clearances at a work location. Some tractor-trailer combinations are prone to over-height collisions at these locations. Collisions are a hazard to all drivers, and repair of the damage typically causes traffic delays. Appropriate solutions to this problem will focus on the prevention of collisions by detecting over-height vehicles and directing the drivers to take an alternate safe route. This presentation addresses the design and functionality of smart detection/alert systems that can be set up well in advance of a known vertical clearance restriction …

On-Site Measurement Of The Water-Cementitious Ratio And Heat Of Hydration Of Delivered Concrete, Seyednavid Mardmomen

Graduate Theses, Dissertations, and Problem Reports (ETD)

In this study, AASHTO T318-15 was adopted to estimate the water content of fresh concrete mixes and then revised to have better precision. The additional step required sieving out the coarse aggregate after drying the sample in a microwave oven, and it was then used in the calculation of the absorbed water and cementitious material content. Several laboratory batches, as well as on-site water-cementitious (w/cm) ratio tests, were performed on concrete mixes containing ordinary Portland cement, ground granulated blast furnace slag, and Class F fly ash. The results of the experiments indicated that the accuracy of the revised method was …

Field Evaluation Of A Modular Press-Brake-Formed Steel Tub Girder In An Application That Includes Skew And Superelevation, Adam D. Roh

Graduate Theses, Dissertations, and Problem Reports (ETD)

The Short Span Steel Bridge Alliance (SSSBA) is a group of bridge and culvert industry leaders (including steel manufacturers, fabricators, service centers, coaters, researchers, and representatives of related associations and government organizations) who have joined together to provide educational information on the design and construction of short span steel bridges in installations up to 140’-0” in length. A technical working group from within the SSSBA developed the notion for the modular shallow press-brake-formed steel tub girder as a solution for the short span steel bridge market.

After extensive testing at West Virginia University and multiple successful field demonstrations, members of …

Civil Engineering Research In Ireland 2020: Conference Proceedings, Kieran Ruane, Vesna Jaksic, Bidisha Ghosh, Magdalena Hajdukiewicz, Ciaran Hanley, Niall Holmes, Jennifer Keenahan, Zili Li, Patrick Mcgetrick, Ted Mckenna, Mary Moloney, Vikram Pakrashi, Niamh Power

Publications

Civil Engineering Research in Ireland 2020: Conference Proceedings.

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Evaluation Of Concrete Deck Curing Regimens Using Capillary Pressure Sensing System, Samuel Spann

Graduate Theses and Dissertations

Early-age plastic shrinkage cracking is a common problem with the construction of concrete bridge decks due to the high surface area-to-volume ratio and exposure to potentially detrimental environmental effects. Curing regimens are utilized to mitigate cracking risk during the plastic stage of the concrete; the curing regimens evaluated for this study were wet burlap-polyethylene sheeting, two acrylic curing compounds, and one lithium compound. Capillary pressure in the water filled pores has been shown to correlate to the plastic shrinkage cracking risk of concrete. A new portable system has been developed to measure the capillary pressure that could potentially be used …

Truck Activity Pattern Classification Using Anonymous Mobile Sensor Data, Taslima Akter

Graduate Theses and Dissertations

To construct, operate, and maintain a transportation system that supports the efficient movement of freight, transportation agencies must understand economic drivers of freight flow. This is a challenge since freight movement data available to transportation agencies is typically void of commodity and industry information, factors that tie freight movements to underlying economic conditions. With recent advances in the resolution and availability of big data from Global Positioning Systems (GPS), it may be possible to fill this critical freight data gap. However, there is a need for methodological approaches to enable usage of this data for freight planning and operations.

To …

Study Of Internal Strains Developed In Concrete Decks At Early Ages In Steel Continuous Bridges, Fernando R. Benitez Ortiz

Graduate Theses and Dissertations

The Arkansas Department of Transportation (ARDOT) has identified bridge deck cracking shortly after concrete decks are placed and prior to applying traffic loads. Previous researchers have confirmed improper construction practices and design methods can lead to deck cracking. Currently, many contractors throughout Arkansas are using continuous deck pours. This construction approach may restrict the concrete slab from movement during early age shrinkage, causing tensile stresses to develop. The final stresses at the end of construction must be lower than the concrete tensile strength, if not cracking issues will develop. Eventually, these cracks may enlarge due to service load stresses and …

Evaluation Of Fracture Principles In Asphalt Concrete Utilizing The Sc(B) Geometry, Airam Marlee Morales Vega

Graduate Theses and Dissertations

Since cracking is one of the principal distresses to be considered in asphalt concrete, multiple fracture tests and geometries have been used to quantify cracking resistance. One of the most popular geometries that have been used in fracture tests is the Semi-Circular bend (SC(B)). However, for this geometry, most of the fracture test methods use different parameters such as thickness, testing temperatures, and loading rates. Thus, the purpose of this research was first to evaluate fracture energy by performing a ruggedness test based on ASTM E1169. Then, to apply fracture mechanics concepts to evaluate three specimen thicknesses (25, 50, and …

The Application Of Gray-Scale Level-Set Method In Segmentation Of Concrete Deck Delamination Using Infrared Images, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Conventional nondestructive delamination detection of concrete pavements through thermography is often based on temperature contrasts between delaminated and sound areas. Non-uniform backgrounds caused by the environmental conditions are often challenging for contrast-based methods to robustly differentiate the delaminated areas from the sound areas. Instead of focusing on the temperature contrast, this study proposes a temperature gradient-based level set method (LSM) to detect boundaries for delamination segmentations. A modified edge indicator function is developed to represent the normalized temperature gradient of a thermal image. The experimental study was conducted to evaluate its applicability and stability for boundary detection in terms of …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Data

Corresponding data set for Tran-SET Project No. 18GTLSU10. Abstract of the final report is stated below for reference:

"This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Data

Corresponding data set for Tran-SET Project No. 18STUTA01. Abstract of the final report is stated below for reference:

"This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth …

Performance Of Drilled Shaft Under Combination Of Complicated Loads Under Hurricane Event, Jie Huang, Sazzad Bin-Shafique

Publications

This project includes experimental and numerical studies to investigate and assess the impact of vertical loads on a laterally loaded drilled shaft under various conditions. The experimental study includes lab testing and lab-scale load test to examine a drilled shaft subjected to vertical and lateral loads at a reduced scale. With the data obtained from the lab-scale testing, a numerical model was calibrated, which was used to perform a parametric study to scrutinize the effect of many possible factors such as soil stiffness, soil friction angle, and drilled shaft geometry. With all the factors considered in this study, the vertical …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Publications

This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth specimen. One specimen with ASTM A1035 MMFX high-strength steel rebars, one with high-strength glass fiber reinforced polymer (GFRP) …