Structural Engineering Commons^™

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: I. Swamp Water, Sulistyoweni Widanarko, Henki W. Ashadi, Andri Krisnadi Wicaksono

Makara Journal of Technology

Most of infrastructures using steel concrete to reinforce the strength of concrete. Steel concrete is so vulnerable to chemical compounds that can cause corrosion. It can happen due to the presence of chemical compounds in acid environment in low pH level. These chemical compounds are SO4 2-, Cl-, NO3 -. There are many swamp area in Indonesia. The acid contents and the concentration of ion sulphate, chlorides, and nitrate are higher in the swamp water than in the ground water .The objective of this research was to find out the influence of corrosive chemicals in the swamp water to the …

Biodiesel's Characteristics Preparation From Palm Oil, Tilani Hamid. S, Rachman Yusuf

Makara Journal of Technology

Biodiesel’s characteristics preparation from palm oil. Using vegetable oils directly as an alternative diesel fuel has presented engine problems. The problems have been attributed to high viscosity of vegetable oil that causes the poor atomization of fuel in the injector system and pruduces uncomplete combustion. Therefore, it is necessary to convert the vegetable oil into ester (metil ester) by tranesterification process to decrease its viscosity. In this research has made biodiesel by reaction of palm oil and methanol using lye (NaOH) as catalyst with operation conditions: constant temperature at 60 oC in atmosferic pressure, palm oil : methanol volume ratio …

Development Of Hardness Measurement Procedure For Nanocomposite Nc-Tin/A-Si3n4, Keba Moto

Makara Journal of Technology

Hardness of nc-TiN/a-Si3N4 nanocomposites which was determined by using two methods of measurements i. e. depth sensing method and remaining plastic indentation area that were magnified by using SEM (Scanning Electron Microscope) lie in the good agreement. The hardness value is not influenced by the biaxial and residual compressive stress. The measurement of the biaxial stress on the substrate shows a very small value of biaxial stress as well as the constant hardness and crystallite size against annealing temperature. Therefore, the reported hardness value here is the intrinsic value that depend on its microstructure properties.

Analogy Method Development For Cost Estimation Of Software Design, Riyanarto Sarno, Joko Lianto Buliali, Siti Maimunah

Makara Journal of Technology

The important aspect of planning and managing software development project is to estimate the cost of a project. There are several methods for estimating the cost of a software development project, and the Analogy method is a method which gives relatively better estimates. This paper shows that the modified Analogy method selects a closer project reference, estimates more accurate project effort and cost. This study enhances the cost estimate technique by including valid and complete cost parameters, therefore the estimate of a project cost is better than the result of the standard Analogy method.

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: Ii. Swamp Sludges, Henki W. Ashadi, Sulistyoweni Widanarko, Irma Gusniani

Makara Journal of Technology

A polluted environment will influence the building age. The objective of this research was to find out the influence of corrosive chemicals within the sludge swamp area with the corrosion rate of steel concrete. Corrosion in steel concrete usually occur in acid area which contain of SO4 2-, Cl- and NO3 -. The research treatment used by emerging ST 37 and ST 60 within 60 days in ‘polluted’ sludge swamp area. Three variation of ‘polluted’ swamp sludge were made by increasing the concentration a corrosive unsure up to 1X, 5X and 10X. The corrosion rate measured by using an Immersion …

Study Effect Of Salt Washing Process On Content And Iodium Stability Of Salt, Nelson Saksono

Makara Journal of Technology

Effect of Salt Washing Process on Content and Iodium Stability of Salt. Salt washing process should increase the salt quality. It should clean the salt from sludge or clay and also reduce the impurity compound such as Mg, Ca and the reductor content. The objective of these reseach is to assess the effect of washing process on the content og hygroscopic impurities compound (Ca and Mg), and reductor content of salt. The research also investigate the water absorbing, pH, KIO3 content as function of time to obtain effect of washing process on KIO3 stability in salt. The experiment result shows …

Making Alloys (Ti1 - Xalx) N Using Plasma Cvd Technique From Alcl3 Powder, H2 And N2 Gas ,With Solvent Ticl4, Keba Moto

Makara Journal of Technology

The substitution of Ti atoms by Al atoms in TiN lattice sites to form (Ti1-xAlx)N is clearly demonstrated by the coatings which were deposited on steel substrate and using plasma CVD technique. The presence of Al atoms in TiN lattice site is shown by means of XRD and EDX techniques: lattice parameters decreasing of TiN as the fraction of Al increases (XRD) and precipitation of hexagonal AlN phase (XRD) as the fraction of Al exceeding 0.8 (EDX). The hardness of these coating are just around 30 GPa, which is beyond the values reported in literatures.

Integrating Passenger And Modulo As Learning Tools For Collaborative Engineering Education, Kalamullah Ramli, Frank Schwarz, Stefan Werner, A Halim Shamsuddin, Axel Hunger

Makara Journal of Technology

The University of Indonesia (UI), Gerhard Mercator University (GMU), the Universiti Kebangsaan Malaysia (UKM) have agreed to cooperate as partners to develop a joint bachelor (3+1) and masters (1+1) degree, and collaborate in the research fi elds of multimedia- and internet-based learning and application level active networks. This paper describes the introduction of the Offshore Project and the extending of information technology applications to the partner institutions in this international cooperation which would very much enhance the operations of the new initiative in engineering education, which could provide students in far distance with more fl exible learning environment.

Effects Of 0.25 % Mo (Molybdenum) Which Is Contained In The Ductile Cast Iron On Mechanical Properties Of Austempered Ductile Iron (Adi)., Nukman Nukman, Bustanul Arifin, Bambang Sugiarto

Makara Journal of Technology

The aim of this research is to investigate the effects of 0.25 % Mo (Molybdenum) which is contained in the ductile cast iron on mechanical properties of Austempered Ductile Iron (ADI). The various temperatures and the holding times are used in the heat treatment processes. Using a given 0.25 % Mo in the ductile iron, ADI's alloyed developes a higher ultimate tensile stress value and decreases the elongation if we compare with the as cast (non alloy ductile iron). The higher impact energy value obtained at 9000 C austenization and 375o C austempering temperatures during 60 minutes holding times. The …

The Manufacturing Properties Of Galvanised Steel Sheet With Hexagonal And Tetragonal Network Of Circle Holes, Rahmat Saptono

Makara Journal of Technology

Galvanized steel sheet of 0.8 mm in thickness was drilled with circle holes of 2.5 mm diameter and spacing arranged in tetragonal and hexagonal pattern. The manufacturing properties of specimen were studied through drawing and stretching simulative test. It was concluded from the results that, at high ratio of punch to hole diameter (40/2.5), the drawing properties (LDR) of both square and hexagonal perforated sheet were slightly lower than that of solid sheet, while hexagonal perforated showing LDR somewhat higher than the square one. The stretching properties (LDH) of sheet, however, were much lower than that of solid sheet while …

Develops The Software Of Dsp Processor For The Cdma Circuitry, Arman Djohan D.

Makara Journal of Technology

This research develops the software of DSP Processor type TMS320C54X for the CDMA circuitry. This research apply two algorithms namely Mathematic Algorithm and table lookup Algorithm. From both algorithms, the research examine what algorithm have the fasted processing time and the smallest memory occupation. From the examination results the Mathematic Algorithm have 20.62 milliseconds processing time and the Table lookup algorithm have 14.08 milliseconds processing time. The Table lookup algorithm have the fastest processing time because the Matematic algorithm need the rounding process of the fi gure. Eventhough such processing time is not exceed from the 125 millisecond of delay …

Object Classfification In Computer Vision With Discriminant Analysis, Amir Hamzahan

Makara Journal of Technology

A robotic sensor system is always supported by a computer system called ‘computer vision’. The important concept of computer vision is object classfifi cation. In this study two algorithms for object classifi cation in this system will be compared. Firstly, A simple method that do not need complex computation and that considered as an informal method is called binary tree decision structure. This method is based on modest caracteristic decriptors of an object such as vertical line, horizontal line or ellipse line. Unfortunately this method has weakness in recognize an image that contaminated by a noise. Secondly, a more formal …

Reliability Indices For Bolted And Nailed Connections In Wood Structures, David Pollock, Donald A. Bender

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Recently published test data for bolted and nailed connections was evaluated to assess the structural reliability inherent in current allowable stress design procedures for connections in wood structures. Reliability indices were determined for timber connections using standard firstorder, second moment (FOSM) procedures. For the connections considered in this study, reliability indices range from 2.6 to5.1, generally providing higher levels of safety than the structural members in timber structures.

Stress And Thermal Analysis Of The Lotec Carrier, Scott Thomas

Honors Capstone Projects and Theses

No abstract provided.

Matrix Structural Analysis, 2nd Edition, William Mcguire, Richard H. Gallagher, Ronald D. Ziemian

Faculty Books

The aims of the first edition of Matrix Structural Analysis were to place proper emphasis on the methods of matrix structural analysis used in practice and to lay the groundwork for more advanced subject matter. This extensively revised Second Edition accounts for changes in practice that have taken place in the intervening twenty years. It incorporates advances in the science and art of analysis that are suitable for application now, and will be of increasing importance in the years ahead. It is written to meet the needs of both the present and the coming generation of structural engineers.

KEY FEATURES …

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Evaluation Of Extreme Wind Speeds In Relation To The Design Of Coastal Structures In Tanzania, Alfonse Dubi

Tanzania Journal of Engineering and Technology (TJET)

Five distribution functions, FT-I and Weibull with the exponent k = 0.75, 1.0, 1.4 and 2.0 respectively, have been applied to 25-year wind data collected between 1972 and 1996 at Tanga, Dar Es Salaam, Zanzibar and Mtwara Meteorological stations. One maximum value for every year from the full data record was drawn to constitute the annual maxima series for each station. For each of the stations, 2-, 50- and 100-year return wind speeds with corresponding 90% confidence intervals were computed. The distribution functions were fitted to the data by the Least Squares Method. Results from the study show that FT-I …

Bolt Bearing Behavior Of Engineered Wood Composites, Stephen J. Carstens, David Pollock

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

The goal of this research was to gain a better understanding of the bolt bearing behavior of engineered wood composites made from yellow poplar lumber. Lumber specimens included in this study were laminated veneer lumber, strandbased lumber, yellow poplar lumber, and Douglas-fir larch lumber. Testing followed the half-hole and full-hole configuration as set forth in ASTM Standard D5764 (1998).

In a previous study by Wilkinson (1991), a strong correlation was shown between bearing strength perpendicular to grain and bolt diameter. This study supports Wilkinson's finding for bearing strength perpendicular-to-grain based on the half hole test configuration. Other findings in this …

Maine Guide To Energy Efficient Residential Construction : A Manual Of Accepted Practices, State Of Maine Energy Conservation Division

Maine Collection

Maine Guide to Energy Efficient Residential Construction : A Manual of Accepted Practices

State of Maine Energy Conservation Division, Department of Economic and Community Development, 59 State House Station, Augusta, Maine 04333-0059

Second Edition - November, 1997

Contents: Dedication / Acknowledgements / Introduction / Part 1. Summary of Maine's Residential Energy Standards / Part 2. Siting and Initial Design Considerations / Part 3. Important Considerations for the Design Phase / Part 4. Recommended Construction Practices / Appendixes

Ultrasonic Detection Of A Plastic Hinge In Bolted Timber Connections, David Pollock, Donald A. Bender, Don E. Bray, James T P Yao

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Connections between structural members are critical elements that typically govern the performance of structural systems; hence, techniques for monitoring the condition of connections are needed to provide early warning of structural damage. Plastic hinge formation in fasteners frequently occurs in timber connections when the yield capacity is exceeded. An innovative pulse echo testing technique was developed for detecting the formation of a plastic hinge in bolted timber connections and estimating the associated magnitude of connection displacement. A shift in overall signal centroid proved to be the best flTedictor of plastic hinge formation, with a coefficient of determination (R2) of 0.9. …

Transport Matrices Of Finite Beams Resting On Elastic Foundations, M. W. Giger

Tanzania Journal of Engineering and Technology (TJET)

A method of derivation of the coefficients of the transport matrix for a finite element resting on one and two-parameter elastic foundation soils is outlined. The coefficients are summarized for both the Bernoulli–Euler and the Timoshenko beam model in tabular form, for general reference. In addition, bounds on the parameters describing beam/soil flexure, beam and soil shear, which govern the validity of the two-parameter elastic solutions are provided in graphical form.

Force Displacement Relationship For The Prediction Of Structural Fluttering, Ladislaus Lwambuka

Tanzania Journal of Engineering and Technology (TJET)

A new presentation of force displacement relationship for the prediction of structural fluttering is discussed in this paper. This topic is limited to a detailed discussion of the derivation of the equations of motion for the rigid streamlined airfoil/flat plate system of three degrees of freedom, which yields expressions for aerodynamic resultant forces due to a steady air flow. The equations of motion presented herein are derived from the conventional classical complex presentation transformed into real matrix equations. This new presentation of the equations of motion constitutes the foundation for the latest state-of-the-art of predicting critical wind loads on the …

Computer-Aided Analysis And Design Of Rectangular Buried Tank Walls And Its Safety Factor Evaluation Based On Yield Line Analysis, Rakiya J. Fatoohi

Civil & Environmental Engineering Theses & Dissertations

This thesis presents the results of a study that determines the true safety factor of underground square reinforced concrete tank walls.

The walls are analyzed and designed by elastic method. The amount and distribution of the reinforcement was determined by use of the alternate design method (working stress) in compliance with all ACI code requirements. The wall's ultimate moment was computed by use of yield line theory assuming non-isotropic reinforcement. The ultimate value of the earth pressure was computed and compared with the elastic analysis and design values to give the true safety factor.

The results of this study indicate …

Structural Sensitivity Analysis On A Parallel Computer, Niu Kian Teck

Civil & Environmental Engineering Theses & Dissertations

Substructuring formulation using adjoint variable approach has been developed for design sensitivity analysis and optimization of large scale structures. In this study, the procedure for statics and sensitivity analysis are re-examined to propose a programming scheme which can be implemented either in a sequential or parallel environment. The computational times of the substructuring formulation using a single processor versus multi-processors are compared to see the effectiveness of the formulation in the concurrent computing environment.

Experimental Determination Of Post-Buckling Performance Of Steel Angles, Rupasiri Purasinghe

Dissertations and Theses

An experimental testing program was conducted to determine the compression member performance in post-buckling region. These results are compared with an analytical computer program developed by Portland State University under Bonneville Power Administration Contract 79-80BP 24005. The paper presents the sensitivity of the performance of single angle compression members to various parameters such as length to radius of gyration ratio, eccentricity, end conditions and yield stress. The effect of local buckling on long member performance is also documented.

Direct Design Of A Portal Frame, Angel Fajardo Ugaz

Dissertations and Theses

This investigation was undertaken to develop plastic design aids to be used in the direct design of optimum frames. It uses the concept of minimum weight of plastically designed steel frames, and the concept of linear programming to obtain general solutions. Among the special characteristics of this study are: A. The integration of both gravity and combined loading conditions into one linear programming problem. B. The application of the revised simplex method to the dual of a parametric original problem. C. The application of A and B above in the development of design aids for the optimum design of symmetrical …