Structural Engineering Commons^™

A Review Of Current Construction Guidelines To Inform The Design Of Rammed Earth Houses In Seismically Active Zones, David Thompson, Charles Augarde, Juan Pablo Osorio

Articles

Sustainability in the materials we use for construction is a prime concern, focusing on reducing the embodied energy and carbon footprints of the materials used. The cement used in concrete products is responsible for a significant proportion of Man's CO2 emissions and its production requires substantial energy input, as do fired clay products. For this reason, products formed from unfired earthen materials are of increasing interest and the current challenges include devising means of robust design for strength and to address durability concerns. One form of earthen construction that employs an in-situ method is rammed earth, and it is a …

The Living Breakwaters Pdr Efforts: Conceptual Scheduling, Calvin O. Walters Jr.

Publications and Research

On October 29, 2012, Superstorm Sandy caused nearly $19 billion in damages in New York City including 69,000 residential units across the five boroughs. This disaster precipitated a post-disaster-rebuilding (PDR) project including roughly $4.2 billion in a Community Development Block Grant allocated towards PDR projects. A portion of the grant was used to construct a living breakwater in Tottenville, Staten Island, consisting of a resiliency approach to risk reduction through erosion prevention, wave energy attenuation, and enhancement of ecosystems and social resiliency to improve resistance to storms for the community of Tottenville. The ridges of each breakwater are designed with …

Evaluating The Effects Of Curing Methods On Bcsa Cement Concrete, Hannah Allen

Civil Engineering Undergraduate Honors Theses

BCSA cement is a type of cement that makes concrete set up much quicker than typical portland cement concrete. BCSA cement concrete also has a much higher compressive strength than that of portland cement concrete. This study was conducted to determine the effect of different curing conditions on the compressive strength of BCSA cement concrete.

Control Strategy For Solar Energy-Saving Lamps For Optimized Energy Utilization And Sustainability Of Operation Durability: Indonesia Case, Burhanuddin Halimi, Agus Purwadi, Nana Heryana

Makara Journal of Technology

To solve the electrification ratio issue, the Indonesian government has promoted the use of solar energy-saving lamps. This study proposes a control strategy that adopts current reference time-based profiling for solar energy-saving lamps. For optimal energy consumption, the current reference profile is determined according to users’ daily energy requirements. From the aspect of user comfort, a gradual step reference profile is also introduced to provide a subtle change in lighting intensity level. The proposed control strategy can minimize energy consumption and optimize the operation durability of the system. The concept is verified by simulating four scenarios, the results of which …

Mechanical Behavior Of Clay Soil Stabilized With Fly Ash And Bottom Ash, Soewignjo Agus Nugroho, Azra Zulnasari, Ferry Fatnanta, Andius Dasa Putra

Makara Journal of Technology

Soil is one of the most important aspects of an infrastructure given its functions of receiving and holding structural loads. However, not all soils have good physical and mechanical properties. To overcome those conditions, stabilization of the soil is practiced to meet the technical requirements. This study aims to determine the behavior of high plasticity clay stabilized with lime, fly ash, and bottom ash. These additives can be used as a stabilizing agent to increase soil strength. The percentage of additives varied from 5%–25% then mixed with clay and were tested through the (Unconfined Compression Strength (UCS) test. The UCS …

Enhancement Of Biogas Production Through Solid-State Anaerobic Co-Digestion Of Food Waste And Corn Cobs, Lukhi Mulia Shitophyta, Anisa Salsabila, Firanita Angraini Putri, Siti Jamilatun

Makara Journal of Technology

Although biogas has been primarily produced through liquid anaerobic digestion, this method leads to the floating and stratification of fibers and non-homogeneous mixing, which can reduce the biogas yield. Alternatively, biogas can be produced by the solid-state anaerobic digestion (SS-AD) of organic material with a high solid content, such as corn cobs. We investigated the co-digestion of food waste and corn cobs as a biomass feedstock for SS-AD in biogas production. We measured the effects of the total solid (TS) content, percentage of food waste, and reduction in volatile solids (VS), from which we determined its appropriate kinetic model. We …

Optimizing The Self-Healing Efficiency Of Hydrogel Encapsulated Bacteria In Concrete, Ricardo Hungria

LSU Master's Theses

Calcium carbonate precipitation through microbial means is a promising pathway for concrete self-healing technologies, mainly for its microcrack sealing attributes. The main goal of this project was to study and optimize the crack healing efficiency of hydrogel encapsulated bacteria in concrete. To achieve this purpose, Bacillus pseudiformus was implemented as the bacteria strain at a concentration of 10⁸ cells/ml. This bacterium strain along with yeast extract was combined along with three different mineral precursors corresponding to magnesium acetate, calcium lactate, and sodium lactate. All these three precursors were evaluated at two concentrations (67.76 mM/l and 75 mM/l). For each …

New Type Of Lightweight Aggregate For Use In Structural Concrete, Jamal Khatib, Ali Jahami, Oussama Baalbaki, Adel Elkordi

BAU Journal - Science and Technology

This research studied the utilization of municipal solid waste incineration bottom ash (MSWI-BA) in lightweight coarse aggregate (LWC) production. A special method was followed to prepare the new aggregate to fully replace the normal aggregates (NWA) in concrete. The mechanical properties such as compressive strength, tensile strength, and elasticity modulus were investigated for the LWC concrete. Then, two beams were prepared; one from LWC and the other from NWC. The structural performance of beams made up of lightweight aggregates compared to normal aggregates was investigated. The results showed that this type of aggregates led to a 20% reduction in concrete …

Effects Of Bonding Pressure And Lamina Thickness On Mechanical Properties Of Clt Composed Of Southern Yellow Pine, Cody S. Bates

Theses and Dissertations

This study produced cross-laminated timber panels at a range of four lamina thickness (5/8, 1, 1 1/8, and 1 1/4 inch) and three bonding pressures (50, 125, 200 psi), producing a total of 12 panels for mechanical testing. The goal of this study is to observe how the thickness and pressure trends affect the mechanical properties of CLT. Tests include flatwise bending, flatwise shear, internal-bond, and delamination. Results showed that bending MOE decreases as the panel thickness increases while bonding pressure had no significance. Bending MOR was less significant for the thickness and more significant for pressure compared to the …

Shear Strength Of Concrete Beams Made With Belitic Calcium Sulfoaluminate Cement, Caleb W. Chesnut

Graduate Theses and Dissertations

The need for a cleaner alternative to portland cement (PC) concrete has led to increasing interest in alternatives to PC. Structural properties of most of these alternative cements are still an open research topic. One promising alternative cement is belitic calcium sulfoaluminate (BCSA) cement. The study presented in this paper investigated the shear strength, long term compressive strength, and carbonation in BCSA cement and PC concrete beams. A total of twelve eight-foot long beams were made; eight BCSA cement concrete beams and four PC concrete beams to be tested at various ages depending on cement type. Two beams of each …

Development Of Lambda Factors For Masonry Design With Lightweight Grout, Rumi Shrestha

All Theses

Reduction in structural mass, improvement in thermal performance, and reduction in shrinkage cracking through internal curing are some of the reasons that lightweight (LW) aggregates have been used in structures and pavements for decades. However, lightweight grout is still not permitted for use in reinforced masonry construction by the TMS 402/602-16 code. In order to realize the benefits of lightweight grout in U.S. reinforced masonry construction, a codified procedure for its use is required which must be informed by experimental testing.

This research is a pilot project directed to characterize the performance of LW grout in comparison to normal weight …

Machine Learning For High-Fidelity Prediction Of Cement Hydration Kinetics In Blended Systems, Rachel Cook, Taihao Han, Alaina Childers, Cambria Ryckman, Kamal Khayat, Hongyan Ma, Jie Huang, Aditya Kumar

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The production of ordinary Portland cement (OPC), the most broadly utilized man-made material, has been scrutinized due to its contributions to global anthropogenic CO₂ emissions. Thus -- to mitigate CO₂ emissions -- mineral additives have been promulgated as partial replacements for OPC. However, additives -- depending on their physiochemical characteristics -- can exert varying effects on OPC's hydration kinetics. Therefore -- in regards to more complex systems -- it is infeasible for semi-empirical kinetic models to reveal the underlying nonlinear composition-property (i.e., reactivity) relationships. In the past decade or so, machine learning (ML) has arisen as a promising, …

Kinetic Modeling Study Of Laminar Burning Velocity Of Gasoline–Ethanol–Methanol Blends At Elevated Temperature And Pressure, Ahmad Syihan Auzani, Cahyo Setyo Wibowo, Riesta Anggarani, Yulianto Sulistyo Nugroho, Bambang Sugiarto

Makara Journal of Technology

Gasoline–ethanol–methanol (GEM) blends have been considered to replace pure gasoline as spark ignition engine fuel. Their physical and chemical properties and performance and emission measurements from real engines have been reported previously. However, a fundamental study that can explain the unique results of GEM compared with those of pure gasoline is lacking. This study aims to compare the laminar burning velocity of GEM blends at different mixtures, equivalence ratios, temperatures, and pressures with that of pure gasoline. A laminar flame propagation model and reaction mechanisms from the literature were were for a numerical simulation. In this study, the chemical components …

Music Information Retrieval Based On Active Frequency, Hardianto Wibowo, Wildan Suharso, Yufis Azhar, Galih Wasis Wicaksono, Agus Eko Minarno, Dani Harmanto

Makara Journal of Technology

Music is the art of combining frequencies. A balance of frequencies gives rise to a harmonious tone. Several features of music can be analyzed, and they include sociocultural background, lyrics, mood, tempo, rhythm, harmony, melody, timbre, and instrumentation. In this study, we use the frequency of instrumentation as a feature for classification because each instrument has a frequency range. To test this frequency range, we use five music genres and one music playing skill. The five genres are dangdut, electronic dance music (EDM), metal, pop/rock, and reggae. The music playing skill is acoustic. Active frequencies are tested using the k-nearest …

Predictive Delivery Man Assignment Problem Using Deep Learning, Rahmadini Payla Juarsa, Taufik Djatna

Makara Journal of Technology

Dispatching is a critical part in current online shopping. It relates to how the delivery man assignment should minimize cost along with the service from a source to an end customer with an appropriate scheduled time. The problem arises as neither enough products to deliver nor delivery men are available for dispatch, resulting in suboptimal service and a waste of money. The study aimed to formulate the cost of restaurant dispatching for inducing a deep learning-based solution with the gated recurrent unit recurrent neural network to receive hourly order data and to engage the result for near feature delivery man …

Effect Of Arc Plasma Sintering On The Structural And Microstructural Properties Of Fe-Cr-Ni Austenitic Stainless Steels, Parikin Parikin, M. Dani, A. Dimyati, N. D. Purnamasari, B. Sugeng, M. Panitra, A. Insani, T. H. Priyanto, S. Mustofa, Syahbuddin Syahbuddin, A. Huang

Makara Journal of Technology

X-ray diffraction techniques were performed to determine the actual crystal structure of A2 austenitic stainless steel (ASS) as-cast and A2 ASS after arc plasma sintering (APS) for 2 s. Computations were conducted on the basis of the Bragg arithmetic formula by comparing the S2 arithmetic with the interplanar spacing. The Bragg arithmetic formula is a simple series for the determination of the crystalline phase of materials based on the Miller indices of cubic shapes or other shapes. A2 ASS as-cast was identified to have a crystal structure of face-centered cubic with lattice parameter a = 3.58 Å. A similar crystal …

Comparison Of Concrete And Steel Jacket Methods For Reinforcing A Concrete Bridge Pier By Numerical And Experimental Studies, Hadi Faghihmaleki

Makara Journal of Technology

Various rehabilitation and strengthening procedures have been developed in recent decades. A study to determine which methods can be implemented to increase the useful life of the bridge before strengthening must be performed. In this study, the seismic behavior of a reinforced concrete bridge pier with dimension 3.5 × 3.5 m, which was reinforced by two steel and a concrete jacket, was investigated. Nonlinear geometric models and materials were analyzed to estimate the seismic parameters of the pier. Results show an increase in energy absorption, ultimate strength, and ductility for the steel jacket, as well as a greater increase in …

Trend Significance Levels Of Rain Onset And Cessation And Lengths Of The Wet And Dry Seasons In Epe, Lagos State, Nigeria, Adekunle Adedeji Alli, Olorunwa Eric Omofunmi

Makara Journal of Technology

This study aims to reduce crop failure resulting from a dry spell, which is the first occurrence of unsustainable rainfall that deceives farmers into planting. Thus, trends need to be tested using hypothesis, kurtosis, and other statistics to analyze the risks associated with unstable planting calendars and their possible mitigation strategies. The daily rainfall data from 1982 to 2018 were obtained from the archive of NASA/POWER SRB/FLASH, and the research location is Epe, Lagos State, Nigeria, which lies at latitude 6.585° N and longitude 3.962° E. Microsoft Excel was used to perform the tests. Results show that the null hypothesis …

Improvement Of Electrical Properties Of Cmc-Pva Doped With Various Contents Of Lino3 As An Application For Hybrid Polymer Electrolytes, Amalia Zulkifli, Norfatihah Mazuki, Ahmad Salihin Samsudin

Makara Journal of Technology

The present work was carried out with the development of hybrid polymer electrolytes (HPEs) by using carboxymethyl cellulose (CMC)–polyvinyl alcohol (PVA) doped with different contents of lithium nitrate (LiNO3) for the determination of their structural and conduction properties. The structural analysis was conducted by using Fourier transform infra-red spectroscopy and showed the interaction between the blend host polymer and ionic dopant, which formed via the coordinating site of CMC-PVA and Li+-NO3−. The complexes of CMC-PVA doped LiNO3 led to an increment in ionic conductivity, as observed by electrical impedance spectroscopy, and the sample containing 20 wt% LiNO3 obtained the highest …

Semi Real-Time Detection Of Subsurface Consolidation Defects During Concrete Curing Stage, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Subsurface consolidation defect is a common issue in concrete pavement construction, and the hidden defects often require costly repairs after project delivery. Therefore, being able to identify this type of defect during construction will enable contractor to conduct quick repairs to avoid costly post-construction rework. In this paper a semi real-time detection approach using infrared thermography is introduced. The developed approach utilizes the hydration heat during curing time to identify the subsurface voids based on the regional temperature contrast. Experimental studies were conducted using artificial void-defect in different sizes and depths. The thermographic analysis is employed to locate the void-defects …

Frequency Effect On Peak Pressure Coefficients Using The Narrowband Synthesis Random Flow Generator (Nsrfg) Method, Zayuris Del Carmen Atencio Mojica

Graduate Theses and Dissertations

The collapse of the Tacoma Narrows Bridge in Washington state in 1940 due to high wind forces gave structural engineers notice of the importance of understanding the behavior of wind forces on infrastructure. Wind forces play an important role in the design of buildings and other structures. ASCE 7-16 is the manual used for the design of these buildings and other structures throughout the country. These design criteria have been approved based on research projects involving experimental procedures. For the design of wind loads, ASCE 7-16 uses criteria based on wind tunnel (WT) tests. However, since the development of computing …

Torsional Behaviours And Crack Localization In Palm Oil Clinker Concrete, Safdar Khan

Student Works (2020-2029)

The utilization of a Palm oil clinker for the production of sustainable lightweight concrete has environmental, economic, and social benefits. This study presents the investigation of the torsional behavior and localization of cracks in concrete at different substitution levels of POC coarse aggregate with granite. The DOE method was used for the design of the control mix, and all other mixes were prepared with the substitution of granite with the increasing amounts of POC at replacement levels of 20%, 40%, 60%, 80%, and 100%. The maximum reduction in the hard density, compression strength, splitting tensile strength, and flexural strength was …

Use Of Biomimicry Design Approach In Constructing Sustainable Resilient Structures (Case Study: Port Of Beirut), Farouk Bader, Marwan Halabi, Hiba Mohsen, Maged Youssef

BAU Journal - Creative Sustainable Development

Resiliency is not the same as sustainability, nor its substitute, but definitely the two concepts complement each other’s. Sustainability is the avoidance of depletion of natural resources to maintain ecological balance whereas resiliency is to recover, adapt and keep going in the face of setbacks. While designing with green approach is important but what will happen to leed points if the building becomes uninhabitable due to disasters, that’s where resiliency comes into play. The 2019 statistics showed that natural disasters accounted for 133 billion dollars losses and manmade ones accounted for other 7 billion in addition to 11,755 people worldwide …

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Improving The Intellectual And Social Development Of Children With Autism: Design Of A Training Center For Autism, Hasti Jalalian

Makara Journal of Technology

Research on the relationship between the role of architecture and the psychology of children with autism, which indicates that appropriate environments for these children can have a significant effect on their healthcare process, has been recently conducted. However, statistics show that autism spectrum disorders are pervasive, and its extent in Iran has been increasing. Moreover, centers that are specifically designed for children with autism are limited, and paradigms are made without considering the mood of these children. Given the role of architecture in designing a suitable space for these children, an investigation that can identify the specific requirements of these …

Analysis Of The Interfacial Reaction Between Bulk Metallic Glass Coated Copper, Nickel, And Titanium With Lead-Free Solders, Andromeda Dwi Laksono, Yee-Wen Yen, Rifqi Aulia Tanjung, Teodoro A. Amatosa, Ruki Harwahyu

Makara Journal of Technology

Bulk metallic glass (BMG) has good mechanical strength, high hardness, wear resistance, and corrosion resistance with promising application in various industries. However, for the industrial production of BMG, the main issue is how to overcome limitations of joining with other materials. The present study focuses on solder processing at low operating temperature to avoid exceeding the recrystallization temperature. A feasible joining process for BMG was developed using lead-free solders. The BMG surface is pre-plated with copper, nickel, or titanium as a wetting layer. The reaction temperature is set between the glass transition temperature of BMG and the melting point of …

Design Of Ac Microgrid Topology With Photovoltaic Uncertainties In A Rural Village, Vannak Vai

Makara Journal of Technology

Energy needs are increasing day by day, especially for developing countries, due to population growth and changing lifestyles. A suitable microgrid topology with renewable energy integration is considered to fulfill the people and society’s needs. This paper focuses on the design of AC microgrid topology for a nonelectrified village with the integration of PV uncertainties in both sitting and sizing. The development of an optimal algorithm based on the conductor use minimization and unbalanced load improvement is proposed. The shortest path is proposed to search for the minimum conductor use. Then, the algorithm for improving the unbalanced load with two …

Mean-Shift Object Tracking Algorithm With Systematic Sampling Technique, Yoanes Bandung, Aris Ardiansyah

Makara Journal of Technology

Mean shift is a fast object tracking algorithm that only considers pixels in an object area, hence its relatively small computational load. This algorithm is suitable for use in real-time conditions in terms of execution time. The use of histograms causes this algorithm to be relatively resistant to rotation and changes in object size. However, its resistance to lighting changes is not optimal. This study aims to improve the performance of the algorithm under lighting changes and reduce its processing time. The proposed technique involves the use of sampling techniques to reduce the number of iterations, optimization of candidate search …

Analysis Of Correlation And Mapping Of Chlorophyll-A Concentrations And Sea Surface Temperatures In Coastal Areas Based On Terra Modis Satellite Image Data, Hendrata Wibisana, Bangun Muljo Sukotjo, Umboro Lasminto

Makara Journal of Technology

Ecosystems in aquatic environments are distinct from ecosystems on land. Changes that occur in ecosystems in aquatic environments affect the lives of biota in these waters, including the fish used as a food source in fishing communities in coastal areas. This study aims to determine the role of remote sensing in mapping and analyzing the relationship between the parameters of sea surface temperature and chlorophyll-a concentrations on the coast. The correlation of sea surface temperature with chlorophyll-a concentrations is modeled via linear regression. An analysis of variance test is performed to establish the suitability of the temperature data for the …

Experimental Study Of Hollow-Core Slab Containing Waste Pet Bottles, Mulia Orientilize, Josia Irwan Rastandi, R. M. Dimas Aries C., Marsha Niken P., Krisna Adi S.S., Abimantrana Abimantrana

Makara Journal of Technology

This study investigated the utilization of plastic-waste concrete as an effort to reduce urban waste problems. The waste plastic bottles were utilized to form the hollows of the hollow-core slabs (HCSs). The bottles were made of polyethylene terephthalate (PET). As a part of green research to reuse waste material, shredded PET was also added to the concrete mixture to improve the HCS strength. The cast-in-site HCS could be constructed without any difficulties. Three parameters were investigated: the effects of void content, shredded PET content, and steel-fiber (SF) content on the HCS ultimate bending capacity (Mu). Fifteen specimens were tested under …