Structural Engineering Commons^™

Mechanical And Transport Properties Of Alkali-Activated Natural Pozzolans As Sustainable Binders, Brittany Radke

Calvert Undergraduate Research Awards

OPC production accounts for 5 to 7% of the global carbon dioxide (CO₂) emissions, contributing to global warming. The desire to reduce CO₂ emissions and produce more durable concrete has given impetus to search for new binders. It is suggested that alkali-activated natural pozzolans have the potential for use as a sustainable replacement for OPC in concrete.

The current study presented herein evaluated fresh, mechanical, and transport properties of alkali-activated natural pozzolan mortars containing various concentrations of sodium hydroxide solutions as an alkaline activator. To this aim, alkali-activated natural pozzolan mortars were made with concentrations of sodium …

Synthesis Of Tungsten Oxide Nanowires Onto Ito Glass Using T-Cvd, Tomy Abuzairi, Bohr-Ran Huang, Tzu-Ching Lin

Makara Journal of Technology

Tungsten oxide is an n-type semiconductor with interesting physical and chemical properties that make it suitable for various technological applications. Tungsten oxide nanowires were synthesized not only at low temperature but also without the use of any catalysts. The tungsten oxide nanowires were synthesized at 550 °C with tungsten layers onto the ITO glass using thermal chemical vapor deposition (T-CVD). The SEM image shows that the tungsten oxide nanowires are effectively grown with the 200 nm tungsten film. The Raman spectra shoulder at ~690 cm-1 proves the synthesized of tungsten oxide nanowires.

Radiation Characteristics Of A Planar Strip Dipole Antenna And A Slot Dipole Antenna For Thz Applications, Catur Apriono, Eko Tjipto Rahardjo

Makara Journal of Technology

The development of a THz system often requires a device that is used to radiate or detect THz waves. One way to fulfill this requirement is to use an antenna. Therefore, we need to consider the radiation characteristics of an antenna working in the THz region. In this paper, we present simulation study of two dipole antennas, i.e. a planar strip dipole antenna and a slot dipole antenna. The simulation results show that a planar strip dipole antenna has a better radiation efficiency (more than 95%) compared to the slot dipole. It also shows that an efficiency of more than …

The Effect Of Pressing Temperature And Time On The Quality Of Particle Board Made From Jatropha Fruit Hulls Treated In Acidic Condition, Apri Heri Iswanto, Fauzi Febrianto, Yusuf Sudo Hadi, Surdiding Ruhendi, Dede Hermawan

Makara Journal of Technology

The high of pH of jatropha fruit hulls causes the negative properties of particleboard made from this material. Adjusting the particle acidity and pressing conditions (temperature and time) is among the technical modifications available to improve this particleboard’s properties. Particle acidity has been adjusted in a previous research project, and immersing the particles in acetic acid was found to be the best treatment in this preliminary research. In order to improve the particleboard’s properties, an experiment was conducted to determine the best pressing temperature and time. The objective of the research was to evaluate the influence of pressing temperature and …

Microgrid Development Using A Grid Tie Inverter, Hartono Budi Santoso, Budiyanto Budiyanto

Makara Journal of Technology

The use of renewable energy sources (RES), especially photovoltaic (PV), to meet the demand of electrical energy has been getting a great deal of attention as an alternative solution to electrical energy deficit problems. RES are being applied in power systems in a variety of configurations including microgrid systems. One of the characteristics of a microgrid is capability to supplying power to grid when there is an excess power to supply local load. This research examines the chances of saving power consumption from grid using power converters grid tie inverter (GTI) in a microgrid configuration. The test is done by …

Surface Treatment Of Fly Ash For Improving The Tensile Strength Of Fly Ash/Unsaturated Polyester Composites, Sugiman Sugiman, Paryanto Dwi Setyawan

Makara Journal of Technology

The paper presents the surface treatment of fly ashes using acid and alkali solution on the tensile strength of the fly ash/unsaturated polyester (UP) composites. Sulfuric acid (H2SO4), hydrofluoric acid (HF) and sodium hydroxide (NaOH) solution with concentration of 0%, 5%, 10%, 15%, and 20% (by weight) were used for surface treatment of fly ashes. Generally, the tensile strength of the treated fly-ash/UP composites shows a significant increase compared to the untreated fly ash. Of all surface treatments studied, the optimum tensile strength was obtained at a concentration of 10%. At this concentration, at a fly ash content of 30% …

Recycling Roof Tile Waste Material For Wall Cover Tiles, Ambar Mulyono, Silfia Mona Aryani, Joko Lulut

Makara Journal of Technology

Prior research on roof tile waste treatment has attempted to find the appropriate technology to reuse old roof tile waste by create wall cladding materials from it. Through exploration and experimentation, a treatment method has been discovered to transform the tile fragments into artificial stone that resembles the shape of coral. This baked clay artificial stone material is then processed as a decorative element for vertical surfaces that are not load-bearing, such as on the interior and exterior walls of a building. Before applying the fragments as wall tiles, several steps must be taken: 1) Blunting, which changes the look …

Semiconductor Thermal Neutron Detector, Toru Aoki, Aki Miyake, Takayuki Nakano, Akifumi Koike, Hisashi Morii, Hidenori Mimura

Makara Journal of Technology

The CdTe and GaN detector with a Gd converter have been developed and investigated as a neutron detector for neutron imaging. The fabricated Gd/CdTe detector with the 25 mm thick Gd was designed on the basis of simulation results of thermal neutron detection efficiency and spatial resolution. The Gd/CdTe detector shows the detection of neutron capture gamma ray emission in the 155Gd(n, g)156Gd, 157Gd(n, g)158Gd and 113Cd(n, g)114Cd reactions and characteristic X-ray emissions due to conversion-electrons generated inside the Gd film. The observed efficient thermal neutron detection with the Gd/CdTe detector shows its promise in neutron radiography application. Moreover, a …

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …

Compression Testing And Failure Modes Of Steel-Concrete Composite (Sc) Structures For Nuclear Containment, Patrick Michael Wanamaker, Amit H. Varma

The Summer Undergraduate Research Fellowship (SURF) Symposium

Although being able to provide much cleaner power than burning coal and other fossil fuels, nuclear power plants are still a tough sell to the general public due to their history of being spontaneously dangerous. The containment structures surrounding these nuclear plants, however, can play a huge role in reducing the risks associated with them. Relatively new designs for these containment assemblies, known as SC (steel-concrete composite) structures, aim to increase the strength and durability of the containment facilities while keeping costs down. By varying the spacing between shear studs, the ratio of concrete to steel, and the ratio of …

The Effect Zeolite Addition In Natural Rubber Polypropylene Composite On Mechanical, Structure, And Thermal Characteristics, Nurdin Bukit, Erna Frida

Makara Journal of Technology

This study was conducted to determine the effect of zeolite as filler on mechanical properties, and thermal structure blends of natural rubber and polypropylene (NR/PP). In this study, NR/PP/PP-g-MA blends was filled uncalcined zeolite and calcined zeolite at different weight percent of the 2, 4, and 6%. Samples were characterized to determine the tensile strength, fracture elongation and Young's modulus. Structure of the samples was investigated using XRD method and thermal characteristics were analyzed using DTA/TGA technique. The results obtained for tensile strength showed a significant influence with the addition zeolite of the NR/PP blends at 2% by weight of …

The Plasma Electrolysis Phenomenon In A Two-Compartment Reactor For Chlor-Alkali Production, Nelson Saksono, Fakhrian Abqari, Setijo Bismo

Makara Journal of Technology

Chlor-alkali is one of the most important processes in the chemical industry. It produces chlorine and caustic soda, which become the main feedstock of daily products. The aim of this study is to report the phenomenon of plasma electrolysis and how it can be used in chlor-alkali production for more efficient energy consumption. When the plasma is formed, the current fluctuates and gradually declines. Plasma electrolysis begins with the process of electrolysis itself. Due to Joule heating, gas bubbles are formed and a sheath is made on both electrodes, resulting in the plasma field. Plasma electrolysis can be identified by …

Determining The Air Gap Length Of An Axial Flux Wound Rotor Synchronous Generator, Abdul Multi, Iwa Garniwa, Uno Bintang Sudibyo

Makara Journal of Technology

The air gap length of the designed axial flux wound rotor (AFWR) synchronous generator is determined properly according to the design parameters. One of the distinct advantages of an axial flux (AF) machine is its adjustable air gap. An AF generator’s performance might be controlled by adjusting its air gap. The designed generator has a smallscale capacity that has 1 kW, 380 V, and 50 Hz. The windings are laid into slots made from laminated core. The slots are carved in the face of the stator and rotors. The generator has a single-double-sided slotted wound stator sandwiched between twin rotors. …

Characteristics Of Vacuum Freeze Drying With Utilization Of Internal Cooling And Condenser Waste Heat For Sublimation, Muhammad Idrus Alhamid, Nasruddin Yusuf, Indra Teuku Meurah Mahlia, Engkos Ahmad Kosasih, Muhamad Yulianto, Rio Ricardi

Makara Journal of Technology

Vacuum freeze drying is an excellent drying method, but it is very energy-intensive because a relatively long drying time is required. This research investigates the utilization of condenser waste heat for sublimation as a way of accelerating the drying rate. In addition, it also investigates the effect of internal cooling combined with vacuum cooling in the pressure reduction process. Jelly fish tentacles were used as the specimen, with different configurations for condenser heat waste and internal cooling valve opening. The results show that heating with condenser heat waste can accelerate the drying rate up to 0.0035 kg/m2.s. In addition, pre-freezing …

A New Experimental Approach To Evaluate Plasma-Induced Damage In Microcantilever, Yuki Nishimori, Shinji Ueki, Masakazu Sugiyama, Seiji Samukawa, Gen Hashiguchi

Makara Journal of Technology

Plasma etching, during micro-fabrication processing is indispensable for fabricating MEMS structures. During the plasma processes, two major matters, charged ions and vacuum–ultraviolet (VUV) irradiation damage, take charge of reliability degradation. The charged ions induce unwanted sidewall etching, generally called as “notching”, which causes degradation in brittle strength. Furthermore, the VUV irradiation gives rise to crystal defects on the etching surface. To overcome the problem, neutral beam etching (NBE), which use neutral particles without the VUV irradiation, has been developed. In order to evaluate the effect of the NBE quantitatively, we measured the resonance property of a micro-cantilever before and after …

Observation Of Photovoltaic Effect And Single-Photon Detection In Nanowire Silicon Pn-Junction, Arief Udhiarto, Sri Purwiyanti, Daniel Moraru, Takeshi Mizuno, Michiharu Tabe

Makara Journal of Technology

We study nanowire silicon pin and pn-junctions at room and low temperature. Photovoltaic effects are observed for both devices at room temperature. At low temperature, nanowire pn-junction devices show their ability to detect single photon. This ability was not been observed for pin devices. Phosphorus-boron dopant cluster in the depletion region is considered to have the main role for single-photon detection capability. Fundamental mechanism of dopant-based single-photon detection in nanowire pn-junction is described in details.

Improvement In Performance Of Zno Based Dsc Prepared By Spraying Method, Rangga Winantyo, Devinda Liyanage, Kenji Murakami

Makara Journal of Technology

This paper reports the effect of TiCl4 on the performance of ZnO based DSC. ZnO was used due to its stability against photo-corrosion and photochemical properties similar to TiO2. Thin films of nanocrystalline ZnO were deposited on transparent conducting oxide glass using spray method. The ZnO films were treated using TiCl4. The cell’s efficiency was found to be 2.5% with TiCl4 post-treatment and 1.9% without TiCl4 post-treatment.

Influences Of Surface Morphology Of Nanostructured Rutile Tio2 Nanorods/Nanoflowers As Photoelectrode On The Performance Of Dye-Sensitized Solar Cell, Mohd Khairul Bin Ahmad, Kenji Murakami

Makara Journal of Technology

Aligned Rutile TiO2 nanorods (r-TNRs) and TiO2 nanoflowers (r-TNFs) were successfully prepared by hydrothermal method. Using hydrochloric acid (HCl) as chelating agent and titanium butoxide (TBOT) as precursor, aligned r-TNRs with r-TNFs were successfully growth onto fluorine-doped tin oxide (FTO) with different morphologies. The influences of surface morphologies to the rutile based Dye-sensitized solar cell (DSC) efficiency are discussed. The highest lightto- electric energy conversion efficiency, 1.80% is achieved using different concentration under simulated solar light illumination of 100 mWcm-2 (1.5 AM).

Fatigue Life Prediction Of The Keel Structure Of A Tsunami Buoy Using Spectral Fatigue Analysis Method, Angga Yustiawan, Ketut Suastika, Wibowo Harso Nugroho

Makara Journal of Technology

One of the components of the Indonesia Tsunami Early Warning System (InaTEWS) is a surface buoy. The surface buoy is exposed to dynamic and random loadings while operating at sea, particularly due to waves. Because of the cyclic nature of the wave load, this may result in a fatigue damage of the keel structure, which connects the mooring line with the buoy hull. The operating location of the buoy is off the Java South Coast at the coordinate (10.3998 S, 108.3417 E). To determine the stress transfer function, model tests were performed, measuring the buoy motions and the stress at …

Production Optimization For Plan Of Gas Field Development Using Marginal Cost Analysis, Suprapto Soemardan, Widodo Wahyu Purwanto, Arsegianto Arsegianto

Makara Journal of Technology

Gas production rate is one of the most important variables affecting the feasibility plan of gas field development. It take into account reservoir characteristics, gas reserves, number of wells, production facilities, government take and market conditions. In this research, a mathematical model of gas production optimization has been developed using marginal cost analysis in determining the optimum gas production rate for economic profit, by employing the case study of Matindok Field. The results show that the optimum gas production rate is mainly affected by gas price duration and time of gas delivery. When the price of gas increases, the optimum …

Structural Reliability Analysis Of Corroded Steel Girder Bridge, Mohammed Shaalan Al Badran

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The natural aging, environmental impact, and appropriate design are certainly playing a serious role in safety of the bridges function. The functional safety of bridge constitutes a prime element of the transportation system serving commuters, passengers and freight. According to Federal Highway Administration, the steel bridges share represents a large amount of the United States’ bridges. In last century, the collapse of both the Silver Bridge at Point Pleasant, West Virginia over the Ohio River on December 15, 1967 and over the Mianus River Bridge in Connecticut on June 28, 1983 showed that steel corrosion has been the leading reason …

Fatigue Testing And Data Analysis Of Welded Steel Cruciform Joints, Alina Shrestha

LSU New Orleans Theses and Dissertations

In this study, ABS Publication 115, “Guidance on Fatigue Assessment of Offshore Structures” is briefly reviewed. Emphasis is on the S-N curves based fatigue assessment approach of non-tubular joints, and both size and environment effects are also considered. Further, fatigue tests are performed to study the fatigue strength of load-carrying and non-load-carrying steel cruciform joints that represent typical joint types in marine structures. The experimental results are then compared against ABS fatigue assessment methods, based on nominal stress approach, which demonstrates a need for better fatigue evaluation parameter. A good fatigue parameter by definition should be consistent and should correlate …

Creep, Fatigue And Creep-Fatigue Interactions In Modified 9% Cr - 1% Mo (P91) Steels, Valliappa Kalyanasundaram

Graduate Theses and Dissertations

Grade P91 steel, from the class of advanced high-chrome ferritic steels, is one of the preferred materials for many elevated temperature structural components. Creep-fatigue (C-F) interactions, along with oxidation, can accelerate the kinetics of damage accumulation and consequently reduce such components' life. Hence, reliable C-F test data is required for meticulous consideration of C-F interactions and oxidation, which in turn is vital for sound design practices. It is also imperative to develop analytical constitutive models that can simulate and predict material response under various long-term in-service conditions using experimental data from short-term laboratory experiments. Consequently, the major objectives of the …

Full Depth Reclamation: Bringing Developing Countries' Transportation Up To Speed, Sadie Smith

Civil Engineering Undergraduate Honors Theses

Often, a direct correlation is observed between a country’s transportation network and economic development. Evidence of this is observed all over the world. Full Depth Reclamation (FDR) is a roadway recycling technique that mills and mixes the existing roadway with a stabilizing agent and then re-compacts the mixture to create a thicker, stabilized pavement layer. This method is both cost effective and environmentally friendly, making it a very appealing option as the need to rehabilitate or increase the structural capacity of existing roads grows. In this study, the material characterization of FDR was examined as a composite material of both …

Plastic Deformation Of Astm A36 Steel Using Two-Stage Light Gas Gun, Shawoon Kumar Roy

College of Engineering: Graduate Celebration Programs

To characterize material deformation in high velocity impact. To validate material models for computation simulation purposes.

This ongoing research is an attempt to study the plastic deformation of A36 steel plate (0.5” thick) under hypervelocity impact. Plastic deformation of the target plate was simulated using finite element software LS-DYNA.

Analysis Of Hole Lifetime In Soi Mosfet Single-Photon Detector, Dedy Septono Catur Putranto, Wei Du, Hiroaki Satoh, Atsushi Ono, Purnomo Sidi Priambodo, Djoko Hartanto, Hiroshi Inokawa

Makara Journal of Technology

Hole lifetime in the silicon-on-insulator (SOI) metal-oxide-semiconductor field-effect transistor (MOSFET) singlephoton detector was evaluated by the analysis of drain current histograms for different light intensities and substrate voltages. It was found that the peaks in the histogram corresponding to the larger number of stored holes grew as the gate bias decreased. This was attributed not to the increased light absorption efficiency or collection efficiency of the photo-generated holes, but to the prolonged hole lifetime presumably caused by the higher transverse electric field inside the body of SOI MOSFET.

Biodiesel Reactor Design With Glycerol Separation To Increase Biodiesel Production Yield, Budy Rahmat, Imas Siti Setiasih, Roni Kastaman

Makara Journal of Technology

The study consisted of reactor design used for transesterification process, effect of glycerol separation on transesterification reaction, determination of biodiesel quality, and mass balance analysis. The reactor was designed by integrating circulated pump/stirrer, static mixer, and sprayer that intensify the reaction in the outer tank reactor. The objective was to reduce the use of methanol in excess and to shorten the processing time. The results showed that the reactor that applied the glycerol separation was able to compensate for the decreased use of the reactant methanol from 6:1 to 5:1 molar ratio, and changed the mass balance in the product, …

Development Of Seebeck-Coefficient Measurement Systems Using Kelvin-Probe Force Microscopy, Kazutoshi Miwa, Faiz Salleh, Hiroya Ikeda

Makara Journal of Technology

Thermoelectric device is investigated by a number of researchers in order to enhance the thermoelectric efficiency. It is known that the efficiency can be improved by quantum effect. However, it is difficult to measure the thermoelectric characteristics of nanometer-scale structures. Thus a new measurement method is expected to be developed. We propose to apply Kelvin-probe force microscopy (KFM) to characterization of thermoelectric materials. KFM can locally observe surface potential of Fermi energy of a sample without touching the sample surface. In the present paper, we estimate the Seebeck coefficient of thin Si-on-insulator layers using KFM.

Recognition System Of Indonesia Sign Language Based On Sensor And Artificial Neural Network, Endang Supriyati, Mohammad Iqbal

Makara Journal of Technology

Sign language as a kind of gestures is one of the most natural ways of communication for most people in deaf community. The aim of the sign language recognition is to provide a translation for sign gestures into meaningful text or speech so that communication between deaf and hearing society can easily be made. In this research, the Indonesian sign language recognition system based on flex sensors and an accelerometer is developed. This recognition system uses a sensory glove to capture data. The sensor data that are processed into feature vector are the 5-fingers bending and the palm acceleration when …

Growth Of Crsi2 Nanostructures Using Crcl2 Powder On Si Substrates, Wen Li, Meng Erchao, Tomoji Matsushita, Shingo Oda, Daisuke Ishikawa, Kaito Nakane, Hirokazu Tatsuoka

Makara Journal of Technology

Chromium disilicide (CrSi2) nanostructures were grown by the exposure of Si (111) substrates to CrCl2 vapor in an argon gas flow at atmospheric pressure without using any metal catalyst. Dependence of the growth condition on the structural property was investigated. Hexagonal-shaped CrSi2 microrods were grown at 750 °C with 0.05 g of CrCl2. As the quantity of CrCl2 increased to 0.1 g, the bundle of CrSi2 nanowires with microrods and web-liked CrSi2 nanostructure with turning angles were grown at 750 °C and 700 °C, respectively. The preliminary discussion on the growth mechanism of CrSi2 micro- and nanostructures was carried out.