Structural Engineering Commons^™

Heterogeneous Thermal Effects On Structural-Grade Steel, Eric Wickersham

Williams Honors College, Honors Research Projects

The AISC Steel Construction Manual covers structural steel design while at atmospheric and elevated temperatures. The manual does not, though, cover what happens to the steel after it has cooled from elevated temperatures. To fill in this knowledge gap, A36 steel was studied with respect to three main criteria: time, temperature, and cooling. Time was sub-divided into a standard burn (17-20min) and a prolonged burn (90min). Temperature was sub-divided into an average burn (600-800⁰F) and an extreme burn (>1200⁰F). To reach such temperatures, a forge was constructed and used during the burning process. Cooling was sub-divided into standard (air …

An Overview Of The Development Of Cement-Based Batteries For The Cathodic Protection Of Embedded Steel In Concrete, Aimee Byrne, Niall Holmes, Brian Norton

Conference papers

This paper presents an overview of the cement-based batteries developed in DIT for use in the cathodic protection of embedded steel in reinforced concrete undergoing chloride-induced corrosion. Cathodic protection delivers an external current (approximately 20mA per m2 of embedded steel) which effectively polarises the internal current generated during corrosion. The batteries developed in DIT comprise of a cement-based electrolyte containing different additives including sand, aggregate, salts, carbon black and plasticiser with protruding anode and cathode metal plates. These batteries produced an initial electrical output of 1.5V and 23mA through a 10 resistor as measured using data acquisition units and a …

Influence Of The Substrate Characteristics On The Bond Behavior Of Pbo Frcm-Concrete Joints, Tommaso D'Antino, Lesley H. Sneed, Christian Carloni, Carlo Pellegrino

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Fiber Reinforced Cementitious Matrix (FRCM) composites can be employed as a valid alternative to Fiber Reinforced Polymers (FRP) composites for strengthening existing reinforced concrete (RC) structures. The weakness of FRCM-concrete joints has been reported to be at the matrix-fiber interface rather than within the concrete substrate, as is usually reported in the case of FRP-concrete joints. The experimental investigations regarding FRCM strengthening available in the literature have been performed by applying the FRCM composite onto a surface that was treated before the application, usually by grinding or sandblasting. However, the role of the substrate characteristics on the failure mechanism of …

Improving Renewable Energy Transition Acceptance: A Simulation Gaming Approach On A Multi Actor Setting In The Netherlands, Aziiz Sutrisno, Jac A. M. Vennix, Noor Syaifudin

Makara Journal of Technology

The Netherlands have tried very hard to increase their renewable energy sources (RES) shares to fulfill the European Union target in 2050. However, RES performance did not show the expected result as the performance declined in 2009 producing even wider gap compare to the target. The Dutch government’s tried to incorporate all interested stakeholders by forming the Dutch energy transition task force. Nevertheless, the task force’s result is also not showing a desirable trend. Key reasons behind the Dutch low RES performance are the lack of shared understanding and positive attitude toward RES development among interested actors. This research uses …

Dual-Band Singly-Fed Proximity-Coupled Tip-Truncated Triangular Patch Array For Land Vehicle Mobile System, Basari Basari, Josaphat Tetuko Sri Sumantyo

Makara Journal of Technology

This paper proposes a dual-band left-handed circularly polarized triangular-patch array that is developed for land vehicle mobile system aimed at mobile satellite communications. The array consists of six tip-truncated triangular patches, which the first three patches are used for reception and the second three patches are used for transmission purpose. Each of three-patches has a beam pattern that can be switched in three different 120°-coverage beam in azimuth-cut plane at a minimum targeted gain at a desired elevation angle. The targeted minimum gain of the array is 5 dBic, in order for data communications with a large geostationary satellite can …

Improvement Of Quality Of Carica Papaya L. With Clove Oil As Preservative In Edible Coating Technology, Eny Kusrini, Anwar Usman, Chrispine Deksita Wisakanti, Rita Arbianti, Dedy Alharis Nasution

Makara Journal of Technology

We have studied utilization of essential clove oil, extracted from clove buds by hydrodistillation, as preservative in edible packaging technology. Preservative of essential clove oil was applied on chopped papaya fruits by using two methods, namely spray and brush. The effects of concentration of clove oil from 0.05 to 0.20% on the preservation of papaya fruits (Carica papaya L.) at room temperature (25 °C) were also evaluated. Physicochemical and in vitro microbiological activities on the papaya fruits that were stored at 25 oC and 85-90% relative humidity were investigated in details. The results indicate that the clove oil at concentration …

Calibration Of Numerical Model For Shoreline Change Prediction Using Satellite Imagery Data, Sigit Sutikno, Keisuke Murakami, Dwi Puspo Handoyo, Manyuk Fauzi

Makara Journal of Technology

This paper presents a method for calibration of numerical model for shoreline change prediction using satellite imagery data in muddy beach. Tanjung Motong beach, a muddy beach that is suffered high abrasion in Rangsang Island, Riau province, Indonesia was picked as study area. The primary numerical modeling tool used in this research was GENESIS (GENEralized Model for Simulating Shoreline change), which has been successfully applied in many case studies of shoreline change phenomena on a sandy beach.The model was calibrated using two extracted coastlines satellite imagery data, such as Landsat-5 TM and Landsat-8 OLI/TIRS. The extracted coastline data were analyzed …

Independency Of Elasticity On Residual Stress Of Room Temperature Rolled Stainless Steel 304 Plates For Structure Materials, Parikin Parikin, David Allen

Makara Journal of Technology

Mechanical strengths of materials are widely expected in general constructions of any building. These properties depend on its formation (cold/hot forming) during fabrication. This research was carried out on cold-rolled stainless steel (SS) 304 plates, which were deformed to 0, 34, 84, and 152% reduction in thickness. The tests were conducted using Vickers method. Ultra micro indentation system (UMIS) 2000 was used to determine the mechanical properties of the material, i.e.: hardness, modulus elasticity, and residual stresses. The microstructures showed lengthening outcropping due to stress corrosion cracking for all specimens. It was found that the tensile residual stress in a …

Oxidation Process Of H 2 O /Uv For Cod Reduction Of Wastewater From Soybean Tofu Production, Komala Pontas, Abrar Muslim

Makara Journal of Technology

Chemical Oxygen Demand (COD) reduction of wastewater from soybean tofu production was studied by conducting advanced oxidation process (AOP) using hydrogen peroxide with UV radiation catalysts in a closed cylindrical glass reactor. The hydroxyl radical (*OH) concentration from H2O2 decomposition was modeled, and exponential trends were found for the *OH concentration over radiation time and operation temperature. As a result, it was found that the maximal *OH concentration was 0.209 mol L-1 at 240 minutes and 50 °C. The *OH concentration exponentially increased following rise in operation temperature. The H2O2/UV AOP application reduced COD concentration to approximately 42.41% from 10,545 …

Uplift Of Shoreline Regions On Pagai Island Due To The September 12, 2007 Mw 8.4 Earthquake Captured By Sar Image, Ashar Muda Lubis

Makara Journal of Technology

At least 25 people were killed by the September 12, 2007 Mw 8.4 Bengkulu earthquake, and many buildings were destroyed in Bengkulu and West Sumatra provinces. It is very important to estimate the earth surface deformation due to the earthquake to understand the rupture size and its process. The aim of this research is to estimate the shoreline change and vertical displacement on Pagai Island associated with the September 12, 2007 Mw 8.4 Bengkulu earthquake. The intensity of ALOS-PALSAR satellite images is used to access the pattern of displacement. The result shows that Pagai Island demonstrated huge uplift due to …

Effect Of Fly Ash Fortification In The Manufacture Process Of Making Concrete Towards Characteristics Of Concrete In Sulfuric Acid Solution, Asep Handaya Saputra, Muhammad Shohibi, Masatoshi Kubouchi

Makara Journal of Technology

Fly ash is a silica or alumino silica material that can be used as a constituent of cement in the concrete manufacturing process. Utilization of fly ash aims to improve durability and minimize the reduction of concrete’s compressive strength exposed to an acidic environment, which can be achieved through the pozzolanic reaction of fly ash with Ca(OH)2 within concrete. The reduced content of Ca(OH)2 through pozzolanic reaction will minimize the tendency of ettringite formation (compounds that cause deterioration and decrease the compressive strength of concrete). In order to determine the relation between fly ash replenishment into concrete with concrete’s characteristics …

A Comparison Of The Bond Behavior Of Pbo-Frcm Composites Determined By Double-Lap And Single-Lap Shear Tests, Lesley Sneed, T. D'Antino, C. Carloni, C. Pellegrino

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents the results of an investigation on the bond behavior and stress-transfer mechanism of polyparaphenylene benzo isoxazole (PBO) fiber-reinforced cementitious matrix (FRCM) composites bonded to a concrete substrate using double-lap and single-lap shear tests. Results of double-lap shear tests with different composite bonded lengths and widths are presented and compared with those from single-lap shear tests previously reported by the authors. The idealized load response developed from single-lap shear tests is found to characterize the response of the composite in double-lap shear tests, although with a few key differences. With the double-lap shear test, load redistribution among the …

Pre-Construction Rock Treatment And Soil Modification Program Using Low Mobility Grout To Mitigate Future Sinkhole Development In A 2,787.1 Square Meter (30,000 Sf) Maintenance Facility, Steven W. Shifflett

Sinkhole Conference 2015

The US Army required construction of a 2,787.1 square meters (30,000 sf) maintenance facility supported on shallow foundations at the Fort Campbell Military Installation. During the subsurface investigation a seven foot air-filled void was encountered in the bedrock within the building footprint. Electrical Resistivity Imaging (ERI) was conducted in an attempt to determine the lateral extent of the encountered void and to establish the general prevalence of karst features at the site. Due to uncertainty in the subsurface conditions, a rock treatment and soil modification program was developed which consisted of a series of targeted exploratory grout holes advanced in …

Application Of Fiscal Incentives For Development Of East Natuna Gas Field For Long-Term National Natural Gas Demand, Marwan Batubara, Widodo Wahyu Purwanto, Akhmad Fauzi

Makara Journal of Technology

East Natuna gas field, which has proven reserves of 46 trillion cubic feet, is projected to meet long-term natural gas needs. However, CO2-content of the gas reserves reaches 71%, leading to expensive development costs. This research investigates the feasibility of the field based on several fiscal incentives. Firstly, gas supply-demand until year 2040 was analyzed. Then, based on the analysis, the field was developed using high CO2 gas separation technology to produce gas of 1300 MMSCFD in 2023, 2600 MMSCFD in 2031, and 3900 MMSCFD in 2039. Finally, the economic feasibility was assessed using cash flow analysis in accordance with …

Thermodynamic Analysis Of Irreversible Heat-Transformers, Niccolo` Giannetti, Arnas Arnas, Andrea Rocchetti, Kiyoshi Saito

Makara Journal of Technology

Absorption heat transformers extend the possibilities for efficient and environment-friendly energy conversion processes. Based on a general thermodynamic model of three-thermal cycles with finite thermal capacity of the heat sources, this paper is intent upon analyzing and optimizing the performance of absorption heat transformers, by including the influence of irreversibility in the analytical expression of the system efficiency. Dimensionless parameters for an overall optimization are defined and a first screening is performed to clarify their influence. Dependence on the main factors is highlighted to suggest how to change them in order to enhance the whole system performance. Under this point …

A New Method For Simulating Power Flow Density Focused By A Silicon Lens Antenna Irradiated With Linearly Polarized Thz Wave, Catur Apriono, Eko Tjipto Rahardjo, Norihisa Hiromoto

Makara Journal of Technology

A terahertz system uses dielectric lens antennas for focusing and collimating beams of terahertz wave radiation. Linearly polarized terahertz wave radiation has been widely applied in the terahertz system. Therefore, an accurate method for analyzing the power flow density in the dielectric lens antenna irradiated with the linearly polarized terahertz wave radiation is important to design the terahertz systems. In optics, ray-tracing method has been used to calculate the power flow density by a number density of rays. In this study, we propose a method of ray-tracing combined with Fresnel’s transmission, including transmittance and polarization of the terahertz wave radiation …

High Temperature Corrosion Of Aluminized Aisi 4130 Steel With The Different Composition Of Nacl/Na2so4 Deposits, Mohammad Badaruddin, Chaur Jeng Wang, Yudhistyra Saputra, Abu Khalid Rivai

Makara Journal of Technology

The high temperature corrosion of AISI 4130 steel can be increased by hot-dip aluminizing coating. The aluminized steel specimens with the deposit composition of 100/0, 30/70, 50/50, 70/30, and 0/100 (wt.%) NaCl/Na2SO4 were oxidized at 750 °C for 1-49 h periods. According to a parabolic rate constant (kp) value, the aluminized steel with deposit composition of 70/30 NaCl/Na2SO4 shows the highest kp value (3.71 × 10-11 g2cm- 4s-1), later followed by the kp value of 3.35 × 10-11 g2cm-4s-1 for 100/0 and the lowest kp value is 7.731 × 10-12 g2cm-4s-1 for 0/100. Whereas, the kp value for the aluminized …

Effects Of Supplier-Manufacturer Relationships On Supply-Chain Performance Of Manufacturing Industries In Indonesia, Rachmad Hidayat, Khisbullah Hudha, Sabarudin Akhmad

Makara Journal of Technology

The present study describes the relationships between commitment, communication, satisfaction, trust, relationship quality with suppliers, and supply-chain performance. The population of the study was manufacturing companies in Indonesia. Respondents were the chief executive officers or corporate secretaries or the designated managers involved in strategic decision making. Samples were taken by using a proportional area random sampling technique. Structural Equation Modeling (SEM) was used for analysis. Results of both direct and indirect testing of hypothesis indicated two hypotheses of positive and significant effects and nine hypotheses of positive but insignificant effects. Those hypotheses of positive and significant effects were the direct …

Stochastic Optimization Of Supply Chain Risk Measures –A Methodology For Improving Supply Security Of Subsidized Fuel Oil In Indonesia, Adinda Yuanita, Andi Noorsaman Sommeng, Anondho Wijonarko

Makara Journal of Technology

Monte Carlo simulation-based methods for stochastic optimization of risk measures is required to solve complex problems in supply security of subsidized fuel oil in Indonesia. In order to overcome constraints in distribution of subsidized fuel in Indonesia, which has the fourth largest population in the world—more than 250,000,000 people with 66.5% of productive population, and has more than 17,000 islands with its population centered around the nation's capital only—it is necessary to have a measurable and integrated risk analysis with monitoring system for the purpose of supply security of subsidized fuel. In consideration of this complex issue, uncertainty and probability …

Transmission Electron Microscopy Characterization Of High-Temperatur Oxidation Of Fe-20cr-5al Alloy Prepared By Focused Ion Beam Technique, Mohammad Dani, Pudji Untoro, Teguh Yulius Surya Panca Putra, Parikin Parikin, Joachim Mayer, Arbi Dimyati

Makara Journal of Technology

The Focused Ion Beam (FIB) technique was applied for cross section preparation of the oxidized alloy for Transmission Electron Microscopy (TEM) study. Prior to preparation, the specimens of Fe-20Cr-5Al alloy sheet were oxidized in air at 1200 oC for 2 minutes, 10 minutes, 2 hours, and 100 hours. The microstructure and elemental composition of the samples were characterized using TEM equipped with an Energy Dispersive X-Ray Spectroscopy (EDX). The Electron Energy Loss Spectroscopy (EELS) was used to determine of the light elements. The TEM investigation reveals remarkable microstructure evolution of the specimens during oxidation which generally exhibit a typical multi-layer …

Phonon-Drag Contribution To Seebeck Coefficient Of Ge-On-Insulator Substrate Fabricated By Wafer Bonding Process, Veerappan Manimuthu, Shoma Yoshida, Yuhei Suzuki, Faiz Salleh, Mukannan Arivanandhan, Yoshinari Kamakura, Yasuhiro Hayakawa, Hiroya Ikeda

Makara Journal of Technology

In order to build high-sensitivity infrared photodetectors using SiGe nanowires, we investigate the thermoelectric characteristics of Ge-on-insulator (GOI) layers as a reference for SiGe. We fabricate p-type GOI substrates with an impurity concentration of 1016-1018cm-3 by a wafer-bonding process using Ge and oxidized Si wafers. Annealing treatment is performed in order to further increase the bonding strength of Ge/SiO2 interface. We measure the Seebeck coefficient in the temperature range of 290-350 K. The Seebeck coefficient of the GOI layers is very close to the theoretical value for Ge, calculated on the basis of carrier transport. Hence, there is a small …

Group Decisions In Value Management, Christiono Utomo, Farida Murti, Arazi Idrus

Makara Journal of Technology

This research deals with a technique to expedite group decision making during the selection of technical solutions for value management process. Selection of a solution from a set of alternatives is facilitated by evaluating using multicriteria decision making techniques. During the process, every possible solution is rated on criteria of function and cost. Function deals more with quality than with quantity, and cost can be calculated based on the theoretical time value of money. Decision-making techniques based on satisfying games are applied to determine the relative function and cost of solutions and hence their relative value. The functions were determined …

Fiber Optic Ring Resonator Sensor Detection Technique Based On Spectral Intensity Integration, Purnomo Sidi Priambodo, Sasono Rahardjo, Gunawan Witjaksono, Djoko Hartanto

Makara Journal of Technology

Resonant field phenomenon in optical ring resonator has been a major theme for various studies and can be used for various sensor applications. The spectral response shape changes are subjects to be discussed and analyzed for detection in optical sensor system. The spectral response changes are caused by various factors ranging from refractive index of the surrounding medium, medium loss due to absorption and scattering, and coupling variation between waveguides. These optical phenomena are mostly used for bio-sensor applications, since it is free from electromagnetic interference (EMI) and non-physically destructive. In this paper, we discuss our current research in developing …

Seebeck Coefficient Of Soi Layer Induced By Phonon Transport, Faiz Salleh, Takuro Oda, Yuhei Suzuki, Yoshinari Kamakura, Hiroya Ikeda

Makara Journal of Technology

The Seebeck coefficient of a patterned Si wire on P-doped SOI (Si-on-insulator) layer with a carrier concentration of 1018 cm-3 was measured near room temperature. The Seebeck coefficient is found to be smaller than that in the SOI layer and to be closer to the calculated Seebeck coefficient including the electronic contribution. The decrease in the Seebeck coefficient of Si wire is likely to occur due to the elimination of the contribution of phonon drag part. From the theoretical calculation of scattering rates by considering the scattering processes in phonon system, it is considered that an increase in phonon-boundary scattering …

Hazard-Driven Drivers’ Behaviours Towards Vehicle-To-Median Safe Distances, Martha Leni Siregar

Makara Journal of Technology

A median is required for a two-way road to separate traffic from opposing lanes and to prevent head-on collisions. However, studies indicate that medians are also perceived as hazards which need to be avoided during driving. This hazard perception is manifested in drivers’ changing behavior towards various types of medians along the driving lanes inform of their tendency to allow various safe distances to the medians. The Indonesian Highway Capacity Manual (IHCM) does not differentiate between types of medians and the influence on the drivers’ choice of safe margin to the medians. Therefore, this study looks into how the existence …

Construction Of A Novel Method Of Measuring Thermal Conductivity For Nanostructures, Hiroya Ikeda, Shoma Yoshida, Yuhei Suzuki, Veerappan Manimuthu, Faiz Salleh, Fujio Kuwahara, Masaru Shimomura, Kenji Murakami

Makara Journal of Technology

With the aim of characterizing the thermal conduction in a nanometer-scaled materials, we have constructed a novel method on the basis of an ac calorimetric method. In this method, periodic sample heating is performed by light irradiation and the corresponding periodic temperature is detected by infrared irradiative thermometer. This makes us measure the thermal diffusivity out of contact with the objective sample. In the present study, we confirm to measure the thermal diffusivity of bulk Si and Cu by this non-contact method with halogen-lamp irradiation. In determining the thermal diffusivity from the relationship between distance deviation and delay time, the …

The Effects Of The Types Of Milk (Cow, Goat, Soya) And Enzymes (Rennet, Papain, Bromelain) Toward Cheddar Cheese Production, Ariestya Arlene, Anastasia Prima Kristijarti, Ivana Ardelia

Makara Journal of Technology

The objectives of this research are to study the effects of different types of milk and enzymes toward the yield and quality (moisture, ash, protein, fat content, and texture) of cheddar cheese and the interaction between those two variables during the process. The types of milk are cow, goat, and soya milk, while the types of enzymes are rennet, papain, and bromelain enzymes. Regarding the procedure, the milk is first pasteurized before CaCl2 and Lactobacillus lactis that acts as the acidifier starter as much as 0.2% (w/v) and 0.5% of the milk volume are added respectively. The amount of enzyme …

Energy And Exergy Analysis Of Kalina Cycle For The Utilization Of Waste Heat In Brine Water For Indonesian Geothermal Field, Nasruddin Nasruddin, Agus Noor Sidiq, Abdulmajeed Mohamad, Rama Usvika

Makara Journal of Technology

The utilization of waste heat in a power plant system—which would otherwise be released back to the environment—in order to produce additional power increases the efficiency of the system itself. The purpose of this study is to present an energy and exergy analysis of Kalina Cycle System (KCS) 11, which is proposed to be utilized to generate additional electric power from the waste heat contained in geothermal brine water available in the Lahendong Geothermal power plant site in North Sulawesi, Indonesia. A modeling application on energy and exergy system is used to study the design of thermal system which uses …

Influence Of Spatial Variations Of Railroad Track Stiffness And Material Inclusions On Fatigue Life, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Railroad transportation is very important for economic growth and effective maintenance is one critical factor for its economic sustainability. The high repetitive forces from a moving railcar induce cyclic stresses that lead to rail bending and potential deterioration due to fatigue crack initiation and propagation. Previous research for prediction of fatigue life has been done under the assumptions of a uniform track bed and a homogeneous rail. However the spatial variation of the track stiffness is expected to increase the maximum stresses in the rail and, therefore, accelerate the fatigue process. The research described in this dissertation is focused on …

Shape Memory Behavior Of Single Crystal And Polycrystalline Ni-Rich Nitihf High Temperature Shape Memory Alloys, Sayed M. Saghaian

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf shape memory alloys have been receiving considerable attention for high temperature and high strength applications since they could have transformation temperatures above 100 °C, shape memory effect under high stress (above 500 MPa) and superelasticity at high temperatures. Moreover, their shape memory properties can be tailored by microstructural engineering. However, NiTiHf alloys have some drawbacks such as low ductility and high work hardening in stress induced martensite transformation region. In order to overcome these limitations, studies have been focused on microstructural engineering by aging, alloying and processing.

Shape memory properties and microstructure of four Ni-rich NiTiHf alloys (Ni50.3Ti29.7Hf20, Ni50.7Ti29.3Hf20, …