Structural Engineering Commons^™

Analysis Of Burning Wood In The Transient State And The Application To Structural Design, Roberta Veliz, Kimberly Guzman

Architectural Engineering

Determining the extent of the contribution of exposed timber on compartment fire dynamics in open floor plans is a complex process. Designers traditionally used compartmentalization design methods which create spaces where flashover is likely, given the fuel load and ventilation conditions. However, due to the large geometric dimensions and spread of fuel, fires in open floor plans are more likely to remain as localized or traveling fires. As such, an understanding of not only ignition potential but also flame spread is critical to characterizing the contribution of exposed timber. An integral step in characterizing the potential contribution is through an …

Effects Of Collision Damage On The Ultimate Strength Of Fpso Vessels, Muhammad Zubair Muis Alie, Dian Ramasari, Taufiqur Rachman, Ristiyanto Adiputra

Makara Journal of Technology

Floating production storage offloading (FPSO) vessels are movable offshore structures. These structures are designed with large dimensions, and their decks are loaded with several types of equipment. During collision damage, the hull and deck parts loaded with equipment are severely affected. Therefore, the ultimate strength of FPSO vessels should be thoroughly checked and evaluated. The objective of the present study is to analyze the ultimate strength of FPSO vessels against collision damage characterized by hogging and sagging under longitudinal bending. The cross section of an FPSO vessel is modeled with elements composed of stiffened and unstiffened plates. The vessel length …

Synthesis Of Epoxy Monoethanolamide From Bauhinia Monandra Seed Oil, Adewale Adewuyi, Rotimi A. Oderinde

Makara Journal of Technology

In this study, we synthesized epoxidised monoethanolamide (EMA) from Bauhinia monandra seed oil (BMO) via a simple reaction route. In this process, BMO was transesterified to obtain a mixture of methyl esters, which was subjected to a urea adduct complexation reaction. The unsaturated methyl esters (BME) from the urea adduct complexation reaction were then epoxidised using performic acid produced in situ in a one-pot reaction system. The epoxidised methyl esters were converted to EMA by reacting them with monoethanolamine (1:10). The progression of the reaction was monitored using Fourier transform infrared spectroscopy and proton nuclear magnetic resonance spectroscopy, and the …

Ethylene Carbonate And Polyethylene Glycol As Efficient Plasticizers In Cmc-Pva-Nh4no3-Based Polymer Electrolyte, Noor Saadiah Mohd Ali, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

This study investigated the influence of plasticizers (polyethylene glycol [PEG] and ethylene carbonate [EC]) on the ionic conduction of CMC-PVA-NH4NO3. Blended biopolymer electrolytes (BBEs) based on carboxymethyl cellulose–polyvinyl alcohol (CMC-PVA) doped with ammonium nitrate (NH4NO3) were obtained via casting solution technique incorporated with PEG and EC, which acted as plasticizers. Electrical impedance spectroscopy (EIS) was conducted to evaluate the effect of plasticization on the ionic conduction properties. The ionic conductivity improved from 1.70 × 10−3 S/cm for un-plasticized BBEs to 3.92 × 10−3 S/cm for plasticized BBEs with EC and 3.00 × 10−3 S/cm for plasticized BBEs with PEG. The …

Liquefaction Potential Analysis Based On Nonlinear Ground Response On The Coastline Of Bengkulu City, Indonesia, Lindung Zalbuin Mase

Makara Journal of Technology

This paper presents the study of the seismic response and liquefaction potential of the coastal area of Bengkulu City during the September 2007 Sumatra earthquake. The study is conducted by collecting site investigation data (standard penetration test) and applying input motion to observe soil response. Synthetic ground motion is generated by considering the important aspects of earthquakes, including focal depth, epicenter, earthquake source, and site classification. The synthetized ground motion is then used as the input motion in the seismic response analysis. The results of this analysis are spectral acceleration and peak ground acceleration at each depth. The resulting spectral …

Comparison Of Phytoremediation And Filtration For Diamond-Mine-Tailings Water Treatment, M. Hafidhuddin Noor, Mijani Rahman, Akhmad Gazali, Nia Kania, Aulia Rahma, Erdina L.A. Rampun, Amalia E. Pratiwi, Muthia Elma

Makara Journal of Technology

The water pollution caused by diamond mine activities can kill aquatic life. In this work, we used phytoremediation and filtration to treat pond water polluted by the tailings of a diamond mine located in South Kalimantan, Indonesia. Einchhornia crassipes (water hyacinth) was utilized as the biomass for the phytoremediation process. Gravel (10–15 mm) and sand (0.1–1 mm) were used as filter media in the simple filtration setup, using an up-flow system (bottom to top). In the experiment, 16 L of diamond tailing water was poured into five phytoremediation reactors (each 60 L in volume), which were then tested over seven …

Ionic Conductivity And Electrochemical Properties Of Alginate–Nn4no3-Based Biopolymer Electrolytes For Edlc Application, Norfatihah Binti Mazuki, Nur Muhitul Jalilah Rasali, Bouchta Sahraoui, Ahmad Salihin Samsudin

Makara Journal of Technology

In this work, alginate doped with various contents of ammonium nitrate (NH4NO3) as a solid biopolymer electrolyte (SBE) was prepared via casting by using distilled water as a solvent. Impedance studies on alginate–NH4NO3 SBE films were conducted via impedance spectroscopy. The lowest bulk resistance (Rb) showed that the maximum ionic conductivity of the sample containing 25 wt.% NH4NO3 at ambient temperature (303 K) was 5.56 × 10−5 S cm−1. The temperature dependence of ionic conductivity was evaluated, and results confirmed that electrolytes followed an Arrhenius behavior. The highest conducting sample was fabricated into an electrical double-layer capacitor and characterized in …

Current Status Of Hydrothermal Treatment For Energy And Material Recovery Toward A Sustainable Post-Consumer Material Cycle, Baskoro Lokahita, Muhammad Aziz, Fumitake Takahashi

Makara Journal of Technology

The demand for energy-efficient and environmentally friendly municipal solid waste (MSW) processing has increased in developing countries. The thermochemical process offers a fast and reliable solution to reutilize or reduce the volume of MSW. Hydrothermal treatment is a novel MSW treatment technology that is compatible with high-moisture-content feedstock. It involves the thermal degradation of MSW in pressurized water or steam, which promotes the disintegration of cellulosic and polymer materials. Recent advances have shown effective MSW conversion into homogenous solid hydrochar with higher energy density. Alkali and chlorine content, which causes issues in combustors, was successfully removed due to the washing …

Correction To: Recommendations Of Rilem Tc 260-Rsc For Using Superabsorbent Polymers (Sap) For Improving Freeze–Thaw Resistance Of Cement-Based Materials (Materials And Structures, (2019), 52, 4, (75), 10.1617/S11527-019-1375-4), Viktor Mechtcherine, Christof Schröfl, Michaela Reichardt, Agnieszka J. Klemm, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Agnieszka J. Klemm is affiliated to Glasgow Caledonian University, Glasgow, UK.

Performance Evaluation Of Lightweight Normal And Geopolymer Foamed Concrete Using Palm Oil Fuel Ash As Partial Replacement Of Binder, M .E. Alnahhal Ahmed

Student Works (2020-2029)

Carbon dioxide (CO2) emissions from Ordinary Portland Cement (OPC) have a detrimental effect on the environment and this had led many researchers to search for other alternatives in the form of sustainable cementitious materials. The depletion of natural resources and dumping the industrial by-products and waste materials are serious concern to our environment. This research focusses on the performance of using a palm oil industrial by-product, namely, palm oil fuel ash (POFA), as a partial replacement for OPC and fly ash (FA) in lightweight normal foamed concrete and lightweight geopolymer foamed concrete, respectively. Thus, using 10, 20, and 30% POFA …

Macro - And Microstructure Evaluation And Field Applications Of Concrete With Recycled Glass Pozzolan, Marija Krstic

Dissertations and Theses

Concrete is the most used material in the world, second only to water. Conventional concrete is produced with Portland cement (PC). The production of cement is an energy intensive operation that has raised significant environmental concerns, since one ton of cement generates an equal ton of CO₂. In the USA about 90 million tons of cement are used annually, with 3 million tons used in New York. Most contemporary concrete applications for buildings and infrastructure use high-performance concrete (HPC) mixtures which are produced by replacing a percentage of cement with supplementary cementitious materials (SCMs), consisting mainly of fly-ash …

Time-Dependent Reliability Framework For Durability Design Of Frp Composites, Rajneesh Kumar Bharil

Graduate Theses, Dissertations, and Problem Reports (ETD)

The life-cycle performance, durability, and aging characteristics of Fiber Reinforced Polymer (FRP or Structural Composites) have been of keen interest to the engineers engaged in the FRP design, construction, and manufacturing. Unlike conventional construction materials such as steel and concrete, the design guidelines to account for the aging of FRP are somewhat scattered or not available in an approved or consistent format. Loss of strength over time or aging of any structural material should be of concern to engineers as the in-service lifespan of many engineering structures is expected to exceed 100 years. Use of durability strength-reduction factors or factors …

Strengthening Of Corroded Steel Structures Using Cfrp – An Experimental Review, Ghada El-Mahdy Ph.D., P.Eng, Abdallah H. Yassin, Abdel El Rahman Khaled

Civil Engineering

Fibre reinforced polymers (FRP) have been widely used to strengthen reinforced concrete structures, however, nowadays their use to strengthen steel structures is under investigation. In particular, the need to strengthen corroded steel structures found in aggressive environments, such as marine environments, which have undergone a reduction in cross-sectional area and hence a reduction in their load-carrying capacity is in need of studying. The main problems that arise when using carbon fibre reinforced polymer (CFRP) sheets to strengthen steel structures is the weakness in the interfacial bond between the CFRP and the steel surface, the thinness of CFRP sheet, and the …

Retrofit Of Corroded Corrugated Metal Culverts Using Gfrp Slip-Liner, Rahulreddy Chennareddy

Civil Engineering ETDs

Culverts are water conveyance structures, typically used to allow water flow and maintain a balance between the flow streams without interrupting structures such as highways and bridges. Corrugated metal pipes (CMPs) have been used as culverts in North America since the 1950s because of their low cost and simple construction method. Today, the corrosion of CMPs is a major problem faced by all U.S. Departments of Transportation. There is an urgent need to provide an efficient solution, one that is corrosion-resistant, to retrofit thousands of corroded CMPs across the country. High specific strength, high strength to weight ratio, corrosion resistance, …

Influence Of Nh4f In Dextran Based Biopolymer Electrolytes: Conductivity And Electrical Analysis, Muhamad Hafiz Hamsan, Mohd Fakhrul Zamani Kadir, Shujahadeen Bakar Aziz, Muhammad Amirul Solihin Azha, Saifful Kamaluddin Muzakir

Makara Journal of Technology

Dextran polymer host was doped with different concentrations of ammonium fluoride (NH4F) via casting technique. In this present work, dextran-NH4F film has been employed to investigate the ionic conductivity using electrochemical impedance spectroscopy from 50 to 5 MHz. The highest room temperature conductivity is achieved at (2.33 ± 0.76) × 10-3 S cm-1 with 40 wt.% NH4F. The electrolyte is found to obey Arrhenius rule at high temperature with activation energy of 0.21 eV. Dielectric analysis has been performed to obtain better understanding on the conductivity pattern. The dielectric parameters e.g. ɛreal, ɛimag, Mreal, and Mimag have been tested as …

Neutron Diffraction Study Of Multiferroic 0.6nife2o4/0.4batio3 Composite, Engkir Sukirman, Yosef Sarwanto, Syahfandi Ahda, Andon Insani

Makara Journal of Technology

Neutron diffraction study on the 0.6NiFe2O4/0.4BaTiO3 multiferroic composite has been carried out. The 0.6NiFe2O4/0.4BaTiO3 multiferroic composites have been synthesized by solid reaction method. In this study, 20 g of BaTiO3 (BTO) and 20 g of NiFe2O4 (NFO) compounds were prepared from the powder raw materials of BaO3 and TiO2 for BTO, and NiO and Fe2O3 for NFO. Furthermore, both BTO and NFO were each crushed for 5 hours using High Energy Milling (HEM). Then the BTO and NFO were calcined in the furnace at 950 °C/5 hours and 900 °C/5 hours, respectively. Both NFO and BTO precursors were manually mixed …

Comprehensive Inspection On The Experimental Ferritic Stainless Steel By Means Of Transmission Electron Microscopy And Neutron Diffraction Techniques, Parikin Parikin, Mohammad Dani, Riza Iskandar, Aziz Khan Jahja, Andon Insani, Joachim Mayer

Makara Journal of Technology

The field of physical metallurgy is one of the primary beacons that guide alloy developments for multipurpose materials such as the in-core structure materials for pressure vessel components and heat exchangers. The surface microstructure of new ferritic steel with significant local constituent materials was characterized by high resolution powder neutron diffractometer (HRPD) and transmission electron microscope (TEM), combined with the energy dispersive X-ray spectroscopy (EDX). The alloy contains73% Fe, 24% Cr, 2% Si, 0.8% Mn, and 0.1% Ni, in %wt. The charge materials were melted by the casting techniques. The neutron diffractograms obtained shows five dominant diffraction peaks at (110), …

A New Synthesized Microalloys Steel Ods Of High Amplitude Ultrasonically Irradiation, Marzuki Silalahi, Hanif Abdurrahman Wicaksana, Ferhat Aziz, Syahfandi Ahda, Mohamad Riza Iskandar

Makara Journal of Technology

Micropowders of oxide-dispersion-strengthened (ODS) steel have been synthesized using the ultrasonic irradiation method with variations in amplitude. The ultrasonic irradiation process is performed for 50 h at a frequency of 20 kHz with 40%, 50%, and 60% amplitudes in toluene solution. The formation of Fe-Cr microalloys in the preparation of Fe- 15Cr-0.5Y2O3 powder was analyzed using SEM-EDS, X-ray diffraction (XRD), and TEM-EDS. The percentage of Fe- Cr phase mass fraction of ODS steel micropowder formed during ultrasonic irradiation with 40%:50%:60% amplitude was 12.2%:34.1%:22.1%, with 25.67:77.02:38.51 nm crystallite size. The crystallite size at 50% amplitude was the largest, and the diffusion …

Study On Antibacterial Of Chitosan/Hydroxyapatite Doped Magnesium Composite As A Material For Bone Graft Applications, Andromeda Dwi Laksono, Teodoro A. Amatosa, Jr., Hilda Pebrianti Octaviana Sitorus, Wentika Putri Kusuma Asih, Sulistijono Sulistijono

Makara Journal of Technology

Hydroxyapatite (HAp) is one of the constituent minerals of bone and teeth, that has been widely used for synthesizing bone graft. Due to the limitation on properties of the hydroxyapatite, it is doping with Magnesium (HAp-Mg). The addition of Chitosan (Chi) was expected to improve the antibacterial properties of HAp-Mg. The present research aims to study the influence of Chitosan with 0, 5, 15, and 25 wt% addition on biocompatibility properties of Chi/HAp-Mg composite. HAp-Mg was synthesized using the sol-gel method; meanwhile, Chi/HAp-Mg composite was manufactured by mixing Chitosan in acetic acid, and HAp-Mg was added into the mixture. The …

Evaluation Of Primal-Dual Splitting Algorithm For Mri Reconstruction Using Spatio-Temporal Structure Tensor And L1-2 Norm, Mia Rizkinia, Masahiro Okuda

Makara Journal of Technology

Magnetic resonance imaging (MRI) is an essential medical imaging technique which is widely used for medical research and diagnosis. Dynamic MRI provides the observed object visualization through time and results in a spatiotemporal signal. The image sequences often contain redundant information in both spatial and temporal domains. To utilize this characteristic, we propose a spatio-temporal reconstruction approach based on compressive sensing theory. We apply spatio-temporal structure tensor using nuclear norm, in addition to the wavelet sparsity regularization. The spatio-temporal structure tensor is a matrix that consists of gradient components of the MRI data w.r.t the spatial and temporal domains. For …

Acute Toxicitystudy Of Choline Based Ionic Liquids Towards Danio Rerio Fish And The Aggregation Behavior Of Their Binary Mixtures, Mansoor Ul Hassan Shah, Nasruddin Nasruddin, Suzana Bt Yusup, Muhammad Moniruzzaman

Makara Journal of Technology

Marine oil spills are effectively controlled by chemical dispersants. However, the toxicity associated with it reduce its employment in marine environment. To overcome this limitation, the acute toxicity of choline based ionic liquids was evaluated as a potential low toxic variant for oil spill remediation. Further, the aggregation behavior of the individual as well as their binary mixtures was also evaluated by employing tensiometry technique. The half-lethal concentration, LC50on zebrafish (Danio rerio) of three choline based ionic liquids showed that the studied ionic liquids (ILs) fall in the range of “practically nontoxic” ( 100-1000 mg L-1).Various micellar properties showed that …

Multifunctional Lightweight Aggregate Containing Phase Change Material And Water For Damage Mitigation Of Concrete, Wenyu Liao, Aditya Kumar, Kamal Khayat, Hongyan Ma

Materials Science and Engineering Faculty Research & Creative Works

This paper presents an innovative concept of multifunctional lightweight aggregate, which is produced by loading phase change material (PCM) into the interior of lightweight sand (LWS) and sealing the surface pores using water. The PCM loaded in the LWS functionalizes it as a temperature management agent in concrete, and the water in surface pores enables internal curing. It has been found that the particle shape and pore structure of crushed expanded shale LWS makes it an ideal carrier for PCM, loading sufficient PCM and maintaining better (compared to natural sand) mechanical interlocking. When coupled with the internal curing effect, the …

The Application Of Gray-Scale Level-Set Method In Segmentation Of Concrete Deck Delamination Using Infrared Images, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Conventional nondestructive delamination detection of concrete pavements through thermography is often based on temperature contrasts between delaminated and sound areas. Non-uniform backgrounds caused by the environmental conditions are often challenging for contrast-based methods to robustly differentiate the delaminated areas from the sound areas. Instead of focusing on the temperature contrast, this study proposes a temperature gradient-based level set method (LSM) to detect boundaries for delamination segmentations. A modified edge indicator function is developed to represent the normalized temperature gradient of a thermal image. The experimental study was conducted to evaluate its applicability and stability for boundary detection in terms of …

Development Of Engineered Cementitious Composites With Conductive Inclusions For Use In Self-Sensing Applications, Benny Suryanto Dr, Danah Saraireh Ms, Steven Walls Mr, Jaehwan Kim Dr, W John Mccarter Prof

International Conference on Durability of Concrete Structures

The mechanical and a.c. electrical properties of a new varietal of engineered cementitious composite (ECC) incorporating conductive inclusions are presented. Electrical measurements were undertaken over a wide frequency range while curing and when under uniaxial tensile loading to study the influence of ongoing hydration and multiple microcrack formation on the composite electrical impedance. When presented in Nyquist format, the work shows that conductive inclusions reduce the bulk resistance of the composite while enhancing its polarizability, transforming the classic, single-arc bulk response of typical cement-based materials to a two-arc response. The bulk resistance was shown to increase with time and damage, …

Mechanical And Microstructure Characteristics Of Concrete-Mixtures Designed For Durability Of Rc-Structures In Corrosive Environment, Saeid A. Alghamdi Dr., S. Ahmad, M. M. Khaled

International Conference on Durability of Concrete Structures

As exposures to chloride-salts are known as prime factors causing initiation and continuity of corrosion-process of steel reinforcement bars in reinforced concrete (RC) structures, it has always been a major concern for designers considering the requirements of structural-durability for targeted-service life of RC-structures in aggressively corrosive environments typically prevalent in coastal regions. Research works previously reported by the researchers have modeled corrosion-process in terms of corrosion-current density, and it was realized that concrete-mixtures design quality and characteristics, degree of exposures to corrosive-agents such as chloride salts, and protective-concrete cover-thickness are now known beyond doubt to be determinant factors as regards …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Data

Corresponding data set for Tran-SET Project No. 18GTLSU10. Abstract of the final report is stated below for reference:

"This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Data

Corresponding data set for Tran-SET Project No. 18STUTA01. Abstract of the final report is stated below for reference:

"This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Publications

This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth specimen. One specimen with ASTM A1035 MMFX high-strength steel rebars, one with high-strength glass fiber reinforced polymer (GFRP) …

Properties Of High Early-Strength Type V Cement Concrete For Rapid Repair, Nader Ghafoori, Matthew O. Maler, Meysam Najimi, Ariful Hasnat

Civil and Environmental Engineering and Construction Faculty Research

This study examines the suitability of ASTM Type V cement concrete for rapid repair applications. To this end, experimental results on transport and durability properties of high earlystrength concretes using ASTM Type V cement were compared with those of a more traditional cement used for rapid repair, i.e. Type III cement. A cement content of 445 kg/m3 (750 lb/yd3 ) was maintained for all studied concretes. The experimental program included compressive strength, absorption, rapid chloride migration, corrosion resistance, and mass loss due to freezing and thawing regimes. The results of this study revealed that use of Type III and V …

A Study Of The Electron Regeneration Efficiency Of Solar Cells Fabricated Using Cmc/Pva-, Alginate-, And Xanthan-Based Electrolytes, Nur Farha Shaafi, Saifful Kamaluddin Muzakir, Bouchta Sahraoui

Makara Journal of Technology

A photovoltaic (PV) mechanism consists of three important steps, i.e., (i) electron excitation upon absorption of photon with energy higher than the bandgap of fluorophore, (ii) excited-state electron injection from the fluorophore to the pho-toelectrode, and (iii) electron regeneration from the electrolyte to the fluorophore. An efficient electron regeneration could be achieved upon fulfillment of the requirements of energy alignment, i.e., lowest unoccupied molecular orbital of fluorophore (LUMOfluorophore) > redox potential of electrolyte > highest occupied molecular orbital of fluorophore (HOMOfluorophore). This study investigated the electron regeneration efficiency of excitonic solar cells fabricated using three polymer-based electrolytes, i.e., (i) 60% carboxymethyl cellulose …