Structural Engineering Commons^™

Dynamic Characteristic Identification Of Seismic-Excited Multi-Story Buildings Through Response-Only Technique, Agung Budipriyanto, Priyo Suprobo

Makara Journal of Technology

Identifying dynamic characteristics of civil engineering structures is still a challenging task. It intends to assess behavior of the structures under time-dependent loads. This paper discusses a methodology suitable for identifying the characteristics of multi-story buildings using only their measured response under earthquake ground excitations. Appropriateness of technique used for structural identification was corroborated through coherence of the structure’s responses. The methodology was applied for identifying the characteristics of 14-story and 20-story office buildings located in a high seismic region. Responses of these two buildings recorded during three different seismic ground motions were investigated. The buildings’ response spectral densities and …

Performance Evaluation Of An Optimized Floating Breakwater In Oblique Waves With A Higher-Order Boundary Element Method, Faisal Mahmuddin, Masashi Kashiwagi

Makara Journal of Technology

In the previous study, the optimal performance of a two-dimensional (2D) floating breakwater shape was obtained. The performance of this shape was also confirmed with a model experiment in a towing tank. Moreover, the shape’s performance in three dimensions (3D) was investigated in a subsequent study. However, to predict the shape’s performance in a real application more accurately, the shape’s characteristics in oblique waves must also be evaluated. In this study, the performance and characteristics of the model (hydrodynamic forces, body motions, wave elevations, and drift forces) are computed using a higher-order boundary element method (HOBEM). The HOBEM, which is …

Synthesis And Characterization Of Soy-Based Polyurethane Foam With Utilization Of Ethylene Glycol In Polyol, Flora Elvistia Firdaus

Makara Journal of Technology

The use of vegetable oils on replacing petroleum has attracted attention of many researchers. The chemical structure of vegetable oils are different from petrochemicals, so the structure of soybean oil has to be chemically modified through its unsaturated fatty acid chain in triglyceride. A two step process was conducted for the preparation of soy-polyol in designated temperatures; 50 °C, 60 °C, and 70 °C. Ethylene glycol (EG) as co-reagent was taking part in soy-polyol synthesis, and the soy-polyol was used as a sole polyol for polyurethane synthesis. Referred to the previous study, the existence of EG in polyurethane synthesis can …

Performances Of Free-Space Optical Communication System Over Strong Turbulence, Ucuk Darusalam, Purnomo Sidi Priambodo, Harry Sudibyo, Eko Tjipto Rahardjo

Makara Journal of Technology

We report an experimental of free-space optical communication (FSOC) system that use tube propagation simulator (TPS) as the turbulence medium. The FSOC system use wavelength of 1550 nm at the rate transmission of 1000 Mbps and amplified with EDFA at the output of +23 dBm. Index structure of 10-15–10-13 as the representation of atmosphere index turbulences are used for simulation of intensity distribution model or scintillation. The simulation use gammagamma and K model as well. The beam wave propagation models used in simulation are plane wave, spherical wave and Gaussian wave. Spherical wave achieves highest performance via gamma-gamma in strong …

Preparations Of Nanostructured Silicide Bundles And Oxide Arrays, Hirokazu Tatsuoka, Wen Li, Erchao Meng, Daisuke Ishikwa, Kaito Nakane, Shingo Oda, Tomoji Matsushita, Natsuki Kurebayashi

Makara Journal of Technology

A variety of nanostructured silicide bundles and oxide nanowire arrays with abundant, non-toxic materials we are prepared. The CrSi2 nanowire and Mg2Si/MgO composite nanowire bundles were synthesized using a Si substrate and a SiOx nanofiber bundle, respectively. The hexagonal MoSi2 nanosheet bundles were also synthesized using a MoS2 layered material as a template. In addition, ZnO, CuO/Cu2O and a-Fe2O3 nanowire arrays were prepared on semiconductor or metallic substrates. The growth phenomena and the structural properties of the nanostructured materials awere investigated. In addition, the preparations of axial and radial nanowire structures weare examined.

Bioethanol Production From Iles-Iles And Sorghum Starch As Raw Materials (Effect Of Cacl 2 Addition And Saccharification Time), Kusmiyati Kusmiyati, Ali Mahmudi

Makara Journal of Technology

Bioethanol produced from agricultural sources is one alternative energy that has been developed to substitute for petroleum. However, the use of food sources such as corn and cassava to produce bioethanol still face obstacles that lead to the scarcity of food and an increase in food prices. The aim of this study was to produce bioethanol from sorghum and iles-iles, which are not used by humans as food, especially in Indonesia. For both materials, the variables studied were saccharification time (4, 8, 24, and 48 h) and concentration of CaCl2 added to the liquefaction slurry (0, 100, 200, 300, and …

The Effect Of Zephyr Layer Orientation On Zephyrboard Made From Oil Palm Petiole, Lusita Wardani, Muhamad Yusram Massijaya, Yusuf Sudo Hadi, I Wayan Darmawan

Makara Journal of Technology

It is very important to utilize oil palm petiole for the production of zephyr boards. This study aimed to analyze the effect of layer orientation on zephyr board quality. Zephyr boards were made with three coating patterns (A = cross perpendicular, B= combine A and C, and C= paralell) and five zephyr layers using urea formaldehyde adhesive. They were pressed for 20 min at a pressure of 25 kgf/cm² and a temperature 120 ºC, to a target density of 0.80 g/cm³ and a size of 300 mm X 300 mm X 12 mm. Our results showed that the physical and …

2014 Road School, Kevin M. Hetrick

Purdue Road School

At the 2014 Road School, this presentation focused on the proposed sliding of the Milton-Madison Bridge, a 15000 ton truss superstructure intended to move laterally 55 feet from a temporary location onto permanent piers. The project was a joint procurement between INDOT and KYTC, with a Design/Build team consisting of Walsh Construction, Buckland and Taylor, and Burgess and Niple performing the slide. The presentation was in early March, with the slide scheduled for later in the month. The slide will be the largest of its kind.

Characterization Of Dynamic Structures Using Parametric And Non-Parametric System Identification Methods, Ayad Al Rumaithi

Electronic Theses and Dissertations

The effects of soil-foundation-structure (SFS) interaction and extreme loading on structural behaviors are important issues in structural dynamics. System identification is an important technique to characterize linear and nonlinear dynamic structures. The identification methods are usually classified into the parametric and non-parametric approaches based on how to model dynamic systems. The objective of this study is to characterize the dynamic behaviors of two realistic civil engineering structures in SFS configuration and subjected to impact loading by comparing different parametric and non-parametric identification results. First, SFS building models were studied to investigate the effects of the foundation types on the structural …

Mechanical And Transport Properties Of Alkali-Activated Natural Pozzolans As Sustainable Binders, Brittany Radke

Calvert Undergraduate Research Awards

OPC production accounts for 5 to 7% of the global carbon dioxide (CO₂) emissions, contributing to global warming. The desire to reduce CO₂ emissions and produce more durable concrete has given impetus to search for new binders. It is suggested that alkali-activated natural pozzolans have the potential for use as a sustainable replacement for OPC in concrete.

The current study presented herein evaluated fresh, mechanical, and transport properties of alkali-activated natural pozzolan mortars containing various concentrations of sodium hydroxide solutions as an alkaline activator. To this aim, alkali-activated natural pozzolan mortars were made with concentrations of sodium …

Role Of Force Resultants Interaction On Fiber Reinforced Concrete, Titchenda Chan

Electronic Theses and Dissertations

Ultra-high performance concrete (UHPC) is a recently developed concrete gaining a lot of interest worldwide, and a lot research has been conducted to determine its material properties. UHPC is known for its very high strength and high durability. Association Francaise de Genie Civil (AFGC) has defined UHPC as a concrete exhibiting compressive strength greater than 150 MPa (22 ksi). To utilize the full compressive strength of UHPC, complementary tension reinforcement is required. A recent research study to find light weight yet high strength alternative deck systems for Florida movable bridges demonstrated that a composite UHPC and high strength steel (HSS) …

Making Bridges Outlast Rising Waters, Daniel Cox

TREC Project Briefs

During Hurricanes Ivan in 2004 and Katrina in 2005, at least 11 highway and railroad bridges along the U.S. Gulf Coast were damaged by wave forces. The spans of these bridges typically rested on bent column supports, and were attached to the supports by a variety of connection methods. Failure of these connections caused bridge spans to be washed away when the water rose high enough to lift them off. To build bridges that can withstand such forces, engineers must be able to estimate the effects the forces will have.

Investigator Daniel Cox of Oregon State University has conducted wave …

Testing And Strengthening Bridge Connections, Christopher Higgins, Peter Dusicka, Michael Scott

TREC Project Briefs

Researchers evaluate and improve the strength of gusset plate connections, essential pieces in bridge design that can fail due to buckling.

A Technical And Economic Appraisal Of Insulation Retrofits, Niamh O'Brien

Theses

The main aim of this literature review is to further develop the project brief and to examine what research has previously been undertaken in the field of thermal conductivity and retrofitting insulation. The basis of this project is to determine the effect of moisture in domestic cavity walls on the effectiveness of retrofitted insulation. The research began by highlighting the reasoning behind the need for insulation within domestic dwellings within Ireland and the guiding legislation in place in relation to this. Carrying on from this, the current methods used to retrofit insulation were examined, along with the types of insulation …

Implementing Green Roofs On Movie Theaters And Shopping Centers: Business Cases In Profitable Sustainability, Ryan J. Miller

Pomona Senior Theses

This thesis presents the business case for installing green roofs on movie theaters and shopping centers. These businesses can then derive increased profits from the environmental benefits of reduced energy use and increased stormwater retention. After presenting the basic design and benefits of a green roof, the thesis develops stand-alone business plans for a movie theater and shopping center. The author finds that green roofs are a profitable sustainability solution for the commercial enterprise.

A Technical And Economic Appraisal Of Insulation Retrofits, Niamh O'Brien

Theses

The main aim of this literature review is to further develop the project brief and to examine what research has previously been undertaken in the field of thermal conductivity and retrofitting insulation. The basis of this project is to determine the effect of moisture in domestic cavity walls on the effectiveness of retrofitted insulation. The research began by highlighting the reasoning behind the need for insulation within domestic dwellings within Ireland and the guiding legislation in place in relation to this. Carrying on from this, the current methods used to retrofit insulation were examined, along with the types of insulation …

A Review Of The Hl-93 Bridge Traffic Load Model Using An Extensive Wim Database, Cathal Leahy, Eugene J. Obrien, Bernard Enright, Donya Hajializadeh

Articles

HL-93, the current bridge traffic load model used in the United States, is examined here. Weigh-in-motion from 17 sites in 16 states, and containing 74 million truck records, is used to assess the level of consistency in the characteristic load effects implied by the HL-93 model. The load effects of bending moment and shear force are considered on single-lane and two-lane same-direction slab and girder bridges with a range of spans. It is found that the ratio of WIM-implied to HL-93 load effect varies considerably from one load effect to another. An alternative model is proposed which achieves improvements in …

Numerical Evaluation Of The Extended Endplate Moment Connection Subjected To Cyclic Loading, Mehdi Ghassemieh, Mehdi Jalalpour, Ali Akbar Gholampour

Civil and Environmental Engineering Faculty Publications

In this paper, the seismic behaviour of extended endplate moment connection is analysed using finite element method (FEM). First, an existing test setup is modelled and analysed using ANSYS computer program. The model is validated by comparing the results from the finite element with the experimental ones. Afterwards, by changing the dimensions of members of the connection, their effect on the overall seismic performance of connection is investigated. The results show that by enlarging the column depth and stiffening the connection, the seismic performance is improved and the thickness of endplate should be chosen in a way that its moment …

Synthesis Of Tungsten Oxide Nanowires Onto Ito Glass Using T-Cvd, Tomy Abuzairi, Bohr-Ran Huang, Tzu-Ching Lin

Makara Journal of Technology

Tungsten oxide is an n-type semiconductor with interesting physical and chemical properties that make it suitable for various technological applications. Tungsten oxide nanowires were synthesized not only at low temperature but also without the use of any catalysts. The tungsten oxide nanowires were synthesized at 550 °C with tungsten layers onto the ITO glass using thermal chemical vapor deposition (T-CVD). The SEM image shows that the tungsten oxide nanowires are effectively grown with the 200 nm tungsten film. The Raman spectra shoulder at ~690 cm-1 proves the synthesized of tungsten oxide nanowires.

Radiation Characteristics Of A Planar Strip Dipole Antenna And A Slot Dipole Antenna For Thz Applications, Catur Apriono, Eko Tjipto Rahardjo

Makara Journal of Technology

The development of a THz system often requires a device that is used to radiate or detect THz waves. One way to fulfill this requirement is to use an antenna. Therefore, we need to consider the radiation characteristics of an antenna working in the THz region. In this paper, we present simulation study of two dipole antennas, i.e. a planar strip dipole antenna and a slot dipole antenna. The simulation results show that a planar strip dipole antenna has a better radiation efficiency (more than 95%) compared to the slot dipole. It also shows that an efficiency of more than …

The Effect Of Pressing Temperature And Time On The Quality Of Particle Board Made From Jatropha Fruit Hulls Treated In Acidic Condition, Apri Heri Iswanto, Fauzi Febrianto, Yusuf Sudo Hadi, Surdiding Ruhendi, Dede Hermawan

Makara Journal of Technology

The high of pH of jatropha fruit hulls causes the negative properties of particleboard made from this material. Adjusting the particle acidity and pressing conditions (temperature and time) is among the technical modifications available to improve this particleboard’s properties. Particle acidity has been adjusted in a previous research project, and immersing the particles in acetic acid was found to be the best treatment in this preliminary research. In order to improve the particleboard’s properties, an experiment was conducted to determine the best pressing temperature and time. The objective of the research was to evaluate the influence of pressing temperature and …

Microgrid Development Using A Grid Tie Inverter, Hartono Budi Santoso, Budiyanto Budiyanto

Makara Journal of Technology

The use of renewable energy sources (RES), especially photovoltaic (PV), to meet the demand of electrical energy has been getting a great deal of attention as an alternative solution to electrical energy deficit problems. RES are being applied in power systems in a variety of configurations including microgrid systems. One of the characteristics of a microgrid is capability to supplying power to grid when there is an excess power to supply local load. This research examines the chances of saving power consumption from grid using power converters grid tie inverter (GTI) in a microgrid configuration. The test is done by …

Surface Treatment Of Fly Ash For Improving The Tensile Strength Of Fly Ash/Unsaturated Polyester Composites, Sugiman Sugiman, Paryanto Dwi Setyawan

Makara Journal of Technology

The paper presents the surface treatment of fly ashes using acid and alkali solution on the tensile strength of the fly ash/unsaturated polyester (UP) composites. Sulfuric acid (H2SO4), hydrofluoric acid (HF) and sodium hydroxide (NaOH) solution with concentration of 0%, 5%, 10%, 15%, and 20% (by weight) were used for surface treatment of fly ashes. Generally, the tensile strength of the treated fly-ash/UP composites shows a significant increase compared to the untreated fly ash. Of all surface treatments studied, the optimum tensile strength was obtained at a concentration of 10%. At this concentration, at a fly ash content of 30% …

Recycling Roof Tile Waste Material For Wall Cover Tiles, Ambar Mulyono, Silfia Mona Aryani, Joko Lulut

Makara Journal of Technology

Prior research on roof tile waste treatment has attempted to find the appropriate technology to reuse old roof tile waste by create wall cladding materials from it. Through exploration and experimentation, a treatment method has been discovered to transform the tile fragments into artificial stone that resembles the shape of coral. This baked clay artificial stone material is then processed as a decorative element for vertical surfaces that are not load-bearing, such as on the interior and exterior walls of a building. Before applying the fragments as wall tiles, several steps must be taken: 1) Blunting, which changes the look …

Semiconductor Thermal Neutron Detector, Toru Aoki, Aki Miyake, Takayuki Nakano, Akifumi Koike, Hisashi Morii, Hidenori Mimura

Makara Journal of Technology

The CdTe and GaN detector with a Gd converter have been developed and investigated as a neutron detector for neutron imaging. The fabricated Gd/CdTe detector with the 25 mm thick Gd was designed on the basis of simulation results of thermal neutron detection efficiency and spatial resolution. The Gd/CdTe detector shows the detection of neutron capture gamma ray emission in the 155Gd(n, g)156Gd, 157Gd(n, g)158Gd and 113Cd(n, g)114Cd reactions and characteristic X-ray emissions due to conversion-electrons generated inside the Gd film. The observed efficient thermal neutron detection with the Gd/CdTe detector shows its promise in neutron radiography application. Moreover, a …

Heavy Vehicle Performance During Recovery From Forced-Flow Urban Freeway Conditions Due To Incidents, Work Zones And Recurring Congestion, Alexander Drakopoulos, Yue Liu, Alan Horowitz

Civil and Environmental Engineering Faculty Research and Publications

Information contained in the Highway Capacity Manual on the influence heavy vehicles have on freeway traffic operations has been based on few field data collection efforts and relied mostly on traffic simulation efforts. In the 2010 Manual heavy vehicle impact is evaluated based on “passenger car equivalent” values for buses, recreational vehicles and trucks. These values were calibrated for relatively uncongested freeway conditions (levels of service A through C) since inadequate field data on heavy vehicle behavior under congested conditions were available. A number of field data collection efforts, that were not included in deriving the passenger car equivalent values …

In-Plane Loading Of Brick Veneer Over Wood Shear Walls, Elias Anis Toubia, James M. Lintz

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

In the design of wood stud walls with brick veneer, current design building codes specify that the wood stud wall should resist all in-plane and out-of-plane loads (IBC 2009). For out-of-plane loads, this assumption is entirely justified as the brittle brick veneer will crack and lose its capacity to resist bending. For in-plane loads, the brick veneer is significantly stiffer than the wood shear wall, and the veneer is unlikely to crack before the wood shear wall reaches its allowable capacity. The assumption that the wood shear wall resists the entire load is based on the further assumption that the …

Research Project Work Plan For Impact Of Cascadia Subduction Zone Earthquake On The Seismic Evaluation Criteria Of Bridges, Peter Dusicka

Civil and Environmental Engineering Faculty Publications and Presentations

The goal of this project is to provide ODOT with the best rational estimate of ground acceleration values for designing new and retrofitting existing bridges. The objectives are to:

• evaluate the hazard by contrasting the acceleration values from individual CSZ events to PSHA values
• provide experimental evidence of damage difference under longer duration shaking expected from CSZ event

One-Dimensional Compressibility Of Intermediate Non-Plastic Soil Mixtures, Sean E. Salazar

Civil Engineering Undergraduate Honors Theses

The results of high stress, one-dimensional compression testing on intermediate soils are presented. Nevada Sand and silica silt mixtures were subjected to very high vertical stresses (140 MPa) in one-dimensional, monotonic compression. Each soil mixture was tested in a nominally loose condition. A specially designed mold with an integrated sensor array was fabricated to contain the soil during pre-consolidation and loading. The 1-D compression curve was plotted for each mixture in the double-logarithmic void ratio (e), and vertical effective stress (σ’v) space and characteristics of the Limiting Compression Curve (LCC) were identified. Initial and post test grain size distribution curves …

Approximating The Seismic Amplification Effects Experienced By Solar Towers Mounted On The Rooftops Of Low-Rise Industrial Buildings, Peter Luiz Balla

Master's Theses

This thesis investigates the acceleration amplification experienced by solar towers mounted on the rooftops of low-rise industrial buildings during a seismic event. Specifically, this thesis looks to assess the validity of using amplification factors adopted by the ASCE 7-05Minimum Design Loads for Buildings and Other Structures to approximate seismic acceleration amplification for roof-mounted solar towers. To investigate the validity of the ASCE 7-05 amplification factors, this thesis conducts timehistory analyses of three theoretical solar towers mounted on the roof of a case study building. The time history analyses are conducted in the finite element computer modeling program SAP 2000 using …