Structural Engineering Commons^™

Data-Driven Methods To Address Truck Parking Shortages For Long-Haul Commercial Truck Drivers, Sharif Mahmud

Graduate Theses and Dissertations

Truck parking is a critical concern for both the trucking industry and the truck drivers. Long-haul commercial truck drivers rely on safe and adequate parking to support interstate commerce, which has become a challenge due to parking shortages. The recent electronic logging device (ELD) mandate, forcing a strict compliance to hours of service (HOS) regulations, are leading to higher demand for parking. A number of federal, regional, and local studies reveal that truck activity will increase and truck parking demand will outpace parking supply in the coming years. Such parking shortages likely disrupt freight flows and pose risks to truck …

Mitigating Calcium Oxychloride Damage In Cementitious Paste And Concrete Utilizing Supplementary Cementitious Materials, Casey Jones

Graduate Theses and Dissertations

It is understood among engineers in the United States (U.S.) that improvement is needed throughout the transportation infrastructure. In the 2021 Infrastructure Report Card produced by the American Society of Civil Engineers, the roadways of this nation merit a D. This leaves room for improvement in order to provide durable pavements throughout this nation. Areas with significant winter weather may have exacerbated effects in decreased roadway longevity due to freezing/thawing cycles and the use of chemical deicers to mitigate gelid roadway conditions. Much research focuses on surface scaling and reinforcement corrosion using these materials; however, joint deterioration, due to chemical …

Response Modification And Seismic Protection Of Yielding Structures Equipped With Inerters And Hysteretic Dampers, Gholamreza Moghimi

Civil and Environmental Engineering Theses and Dissertations

This study investigates the seismic response of structures with sustainable, long-stroke response modification devices. The main thrust of the dissertation is the investigation of the seismic response of yielding structures equipped with supplemental rotational inertia, or inerters. The last chapter of this dissertation investigates the seismic response of multistory yielding steel structures equipped with pressurized sand dampers.

Inerters are mechanical devices with resisting force proportional to the relative acceleration of their end nodes. This class of response modification devices complements the traditional fluid viscous damping devices with resisting force proportional to the relative velocity at their end-nodes. Mass-amplification is the …

Fragility Functions Of Manufactured Houses Under Earthquake Loads, Shuyah Tani Aurore Ouoba

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Manufactured homes are factory-built homes made of wooden structural members, then transported and installed on a given site. Manufactured housing is used in many countries, such as in Australia, and in New Zealand but remain mostly popular in the United States. In 2020, nearly 22 million people were estimated to live in manufactured homes in the United States, with an increase of more than fifty percent in the shipment over the past seven years. However, performance observations from the last decades have shown the vulnerability of manufactured homes to extreme events, like windstorms and earthquakes. Damage assessments and post-event evaluations …

Analysis Of Laminated Beams: A Bibliometric Review, Arati Waghmare, Sanjay Kulkarni

Library Philosophy and Practice (e-journal)

In this paper statistical analysis of literature on “Analysis of Laminated Beams” using Scopus and Web of Science database is done. Reason behind bibliometric study of literature is to understand the extent of research in this particular area. Since Scopus and Web of Science indexing are known as the most reliable sources amongst all the peer reviewed journals, literature from Scopus and Web of Science database only is taken into consideration. Benchmarks used for the analysis are publications in a year, published articles of different authors, citations of authors etc. Considered period is from 2000 to 2020. It is found …

A Novel Probabilistic Framework Of Rc Corroded Structures Under Dynamic Loading, Rawan Mouin Mashmoushy Eng., Wael Slika, Adel Elkordi

BAU Journal - Science and Technology

Steel corrosion in reinforced concrete structures can lead to severe deterioration damage under static and seismic loads. In practice, it is essential to mitigate failure risk by quantifying the extent of damage and simulating the structural response of damaged structures. However, numerical modeling of the dynamic behavior of corroded structure is challenging due to high nonlinearity of the problem and its multidisciplinary nature. In addition, corrosion damage exhibits various sources of uncertainty that impede accurate deterministic modeling of the dynamic response of RC structures. Therefore, this study presents a simplified framework, to simulate the non-linear response of corroded structures under …

Torsional Behaviours And Crack Localization In Palm Oil Clinker Concrete, Safdar Khan

Student Works (2020-2029)

The utilization of a Palm oil clinker for the production of sustainable lightweight concrete has environmental, economic, and social benefits. This study presents the investigation of the torsional behavior and localization of cracks in concrete at different substitution levels of POC coarse aggregate with granite. The DOE method was used for the design of the control mix, and all other mixes were prepared with the substitution of granite with the increasing amounts of POC at replacement levels of 20%, 40%, 60%, 80%, and 100%. The maximum reduction in the hard density, compression strength, splitting tensile strength, and flexural strength was …

Engineering Students' Perceptions Of Their Development Of Professional Skills, Caitriona Depaor, Una Beagon, Aimee Byrne, Darren Carthy, Patrick Crean, Louise Lynch, Dervilla Niall

Conference Papers

No abstract provided.

Journeyman International: Dwell Being Jonestown, Mississippi, Autumn Wagner

Architectural Engineering

Journeyman International is a non-profit organization that works with countries all over the world to support humanitarian projects by pairing clients with design professionals and volunteers to oversee the design and construction of projects. This specific project partners with Third Lens Ministries and But God Ministries, two organizations that are hoping to empower the community in Jonestown, Mississippi. Dwell Being promotes sustainability and affordable housing in a new housing community in Jonestown that is designed for healthy living and community interaction. Jonestown is a very small 0.4 square acre town that has roots in systemic racism and oppression. A once …

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Context-Aware Sensing And Fusion For Structural Health Monitoring And Night Time Traffic Surveillance, Xinxiang Zhang

Electrical Engineering Theses and Dissertations

Rapid developments in computer vision technologies have been transforming many traditional fields in engineering and science in the last few decades, especially in terms of diagnosing problems from visual images. Leveraging computer vision technologies to inspect, monitor, assess infrastructure conditions, and analyze traffic dynamics, has gained significant increase in both effectiveness and efficiency, compared to the cost of traditional instrumentation arrays to monitor, and manually inspect civil infrastructures and traffic conditions. Therefore, to construct the next-generation intelligent civil and transportation infrastructures, this dissertation develops a comprehensive computer-vision based sensing and fusion framework for structural health monitoring and intelligent transportation systems. …

Reliability Of Sfrp-Strengthened Rc Bridge Columns Subjected To Blast Loads, Ahmad Alsendi, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

The reliability of reinforced concrete bridge columns strengthened with externally bonded, steel-fiber reinforced polymer fabric subjected to blast loads was investigated. Columns were modeled with a nonlinear finite element approach that considers material damage, fracture, and separation. Different concrete strengths, longitudinal reinforcement ratios, and gravity and blast load levels were considered, while uncertainties in material strength and stiffness parameters, as well as load characteristics, were incorporated in the probabilistic analysis. It was found that the use of SFRP can allow significant increases in blast load while maintaining the same level of column reliability.

Comparison Of The Resistance Of Belitic Calcium Sulfoaluminate Cement And Portland Cement To Sulfate Attack And Sulfuric Acid, Rilye Dillard

Graduate Theses and Dissertations

Microbially induced corrosion (MIC) is a fairly common concrete deterioration mechanism with many negative effects. MIC is a complex chemical and biological process that occurs in sewage systems and is nearly impossible to replicate in a laboratory setting. For this study, sulfate and sulfuric acid attack on concrete were studied to mimic two stages of the MIC process. The ASTM C1012, Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution and a modified ASTM C1012 accelerated method were used to compare the sulfate resistance of belitic calcium sulfoaluminate (BCSA) cement, portland cement (PC), and PC-fly …

Experimental Design And Preliminary Testing For Skewed Special Moment Frame Prequalification, Sara Alimirzaei

Graduate Theses and Dissertations

Special moment frames having specially detailed connections are common in high seismic regions, providing architectural flexibility for passageways and views without brace obstructions. In situations where the building framing layout requires deviation from typical rectangular framing, skew in the moment frame connections may be required. Currently, the AISC prequalified connections only include testing of orthogonal moment frame connections and it is unclear whether the existing design methods can accommodate skew at the beam-to- column connections. To investigate the effect of out-of-plane skew on the performance of reduced beam section special moment frame connections, an experimental test is designed and a …

Development Of An Ultraviolet Absorbance Assay To Estimate Air Entrainer Dosing For Concrete Containing Fly Ash, James Spencer

Graduate Theses and Dissertations

Fly ash is a coal combustion byproduct that can be used as a supplementary cementitious material (SCM) in concrete, offering benefits such as increased workability, durability, and strength. Fly ash can be used as a partial replacement to cement, reducing concrete productions costs and decreasing disposal in landfills. However, variability of fly ash properties (e.g., carbon content, adsorption site density) confounds estimates of the air entraining admixture (AEA) dose needed to achieve a specified air content in concrete. Air entrainment is needed to improve freeze-thaw resistance and limit concrete cracking. The foam index (FI) test is currently used to estimate …

On The Computational Efficiency Of Les And Hybrid Rans-Les Models In Building Aerodynamics, Aly Mousaad Aly, Faiaz Khaled

Faculty Publications

Large-eddy simulation (LES) has proven to offer superior accuracy in regards to predicting surface pressures compared to the Reynolds-averaged Navier Stokes (RANS) models. However, the primary impediment is the high computational cost associated with LES. The authors attempt to investigate the computational cost and accuracy by employing different sub-grid scale (SGS) models in LES and hybrid RANS-LES models. One of the prerequisites of accurate pressure estimations is to ensure a horizontally homogeneous empty computational domain. This study aims to compare the computational competence qualitatively and quantitatively using an empty domain in regards to the ability to maintain horizontal homogeneity. The …

Analysis Of Shear-Strength In Weathered Shale Strata Along A Highway Slope Failure Site In Northwest Arkansas, Olivia Overton

Civil Engineering Undergraduate Honors Theses

Slope failures cost millions of dollars per year to repair and can be deadly. Accurate modeling of slope conditions, including soil parameters, water table locations, and depth to bedrock, are essential to determining the overall stability of a slope. This project is a continuation of the work completed in 2019 by a former University of Arkansas researcher, Vanessa LeBow. LeBow RocScience used Slide2 modeling software to model two highway embankment slopes in Northwest Arkansas that experienced slope movement to determine whether increased use of geophysical data could increase the accuracy of slope stability models. A parametric study of shear strengths …

On The Computational Efficiency Of Les And Hybrid Rans-Les Models In Building Aerodynamics, Faiaz Khaled, Aly Mousaad Aly

Faculty Publications

No abstract provided.

Design Of Load Bearing Wall For Low Rise Building With Partially Grouted Reinforced Masonry, Anil Bhatt

Honors Theses

The seismic and wind load acting on the 2-storeyed building of dimension 120 ft x 98 ft located in Oxford, MS, were calculated and the seismic load was considered for the design of the 120 ft long and 24 ft high load-bearing wall because it being critical. The maximum loading was computed using different load combinations. The masonry behavior and masonry specifications were considered to select the masonry unit, grout, and mortar for the load-bearing wall. The seismic design requirement for the shear and slender wall was fulfilled for the special reinforced masonry wall. The in-plane and out-of-plane loading scenarios …

Modeling Considerations For Built-Up Compression Members In Communication Towers, Ghada M. El-Mahdy P.Eng., Ceng, Amro A. Alawamry

Civil Engineering

It is a well-established fact that built-up compression members exhibit extra flexibility than their equivalent solid members due to the shear action which effects the overall stability. This is usually taken into consideration by using a modified slenderness ratio for buckling modes that involve relative deformation of the interconnectors. Built-up members are often used as space truss members in communication towers. When modeling communication towers in structural analysis programs like SAP2000, the built-up member is usually defined as a single member element with a double section cross section. This does not catch the increase in deflection in the member due …

Evaluation Of Permanent Concrete Barriers To Mash 2016, Samuel Elias Hovde

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The objective of this research project was to develop evaluation criteria for permanent concrete barriers to MASH 2016 TL-3 and TL-4 without crash testing and then to evaluate permanent concrete barrier standards provided by the sponsoring agencies of the Midwest Pooled Fund Program. A literature review was conducted to determine evaluation criteria for stability, shape, strength, and anchorage, and a database of permanent concrete barrier crash tests was compiled. A survey was conducted to collect barrier standards from the members of the Midwest Pooled Fund Program, and barriers were selected and evaluated according to the determined methodology. A total of …

Improving The Intellectual And Social Development Of Children With Autism: Design Of A Training Center For Autism, Hasti Jalalian

Makara Journal of Technology

Research on the relationship between the role of architecture and the psychology of children with autism, which indicates that appropriate environments for these children can have a significant effect on their healthcare process, has been recently conducted. However, statistics show that autism spectrum disorders are pervasive, and its extent in Iran has been increasing. Moreover, centers that are specifically designed for children with autism are limited, and paradigms are made without considering the mood of these children. Given the role of architecture in designing a suitable space for these children, an investigation that can identify the specific requirements of these …

Analysis Of The Interfacial Reaction Between Bulk Metallic Glass Coated Copper, Nickel, And Titanium With Lead-Free Solders, Andromeda Dwi Laksono, Yee-Wen Yen, Rifqi Aulia Tanjung, Teodoro A. Amatosa, Ruki Harwahyu

Makara Journal of Technology

Bulk metallic glass (BMG) has good mechanical strength, high hardness, wear resistance, and corrosion resistance with promising application in various industries. However, for the industrial production of BMG, the main issue is how to overcome limitations of joining with other materials. The present study focuses on solder processing at low operating temperature to avoid exceeding the recrystallization temperature. A feasible joining process for BMG was developed using lead-free solders. The BMG surface is pre-plated with copper, nickel, or titanium as a wetting layer. The reaction temperature is set between the glass transition temperature of BMG and the melting point of …

Design Of Ac Microgrid Topology With Photovoltaic Uncertainties In A Rural Village, Vannak Vai

Makara Journal of Technology

Energy needs are increasing day by day, especially for developing countries, due to population growth and changing lifestyles. A suitable microgrid topology with renewable energy integration is considered to fulfill the people and society’s needs. This paper focuses on the design of AC microgrid topology for a nonelectrified village with the integration of PV uncertainties in both sitting and sizing. The development of an optimal algorithm based on the conductor use minimization and unbalanced load improvement is proposed. The shortest path is proposed to search for the minimum conductor use. Then, the algorithm for improving the unbalanced load with two …

Mean-Shift Object Tracking Algorithm With Systematic Sampling Technique, Yoanes Bandung, Aris Ardiansyah

Makara Journal of Technology

Mean shift is a fast object tracking algorithm that only considers pixels in an object area, hence its relatively small computational load. This algorithm is suitable for use in real-time conditions in terms of execution time. The use of histograms causes this algorithm to be relatively resistant to rotation and changes in object size. However, its resistance to lighting changes is not optimal. This study aims to improve the performance of the algorithm under lighting changes and reduce its processing time. The proposed technique involves the use of sampling techniques to reduce the number of iterations, optimization of candidate search …

Analysis Of Correlation And Mapping Of Chlorophyll-A Concentrations And Sea Surface Temperatures In Coastal Areas Based On Terra Modis Satellite Image Data, Hendrata Wibisana, Bangun Muljo Sukotjo, Umboro Lasminto

Makara Journal of Technology

Ecosystems in aquatic environments are distinct from ecosystems on land. Changes that occur in ecosystems in aquatic environments affect the lives of biota in these waters, including the fish used as a food source in fishing communities in coastal areas. This study aims to determine the role of remote sensing in mapping and analyzing the relationship between the parameters of sea surface temperature and chlorophyll-a concentrations on the coast. The correlation of sea surface temperature with chlorophyll-a concentrations is modeled via linear regression. An analysis of variance test is performed to establish the suitability of the temperature data for the …

Artificial Intelligence Driven Infrastructure Management And Maintenance Plan, Julian Jesso

Doctoral Dissertations and Master's Theses

Rapid development in trucking technology and increasing demands in freight transportation has led to longer and heavier vehicles traveling on Florida’s highway system. Vehicles with gross vehicle weight (GVW) over 80,000 pounds, or permit vehicles, have significant effects on infrastructure, thus requiring an approved permit prior to departure. The combination of these increasing loads and harsh environmental conditions that Florida is subject to requires an enhanced infrastructure management program. Additionally, there is a need to eliminate inconsistencies in permit applications and derive a uniform maintenance practice for Florida’s infrastructure. In this research, the focus was to develop an analytical procedure …

Experimental Study Of Hollow-Core Slab Containing Waste Pet Bottles, Mulia Orientilize, Josia Irwan Rastandi, R. M. Dimas Aries C., Marsha Niken P., Krisna Adi S.S., Abimantrana Abimantrana

Makara Journal of Technology

This study investigated the utilization of plastic-waste concrete as an effort to reduce urban waste problems. The waste plastic bottles were utilized to form the hollows of the hollow-core slabs (HCSs). The bottles were made of polyethylene terephthalate (PET). As a part of green research to reuse waste material, shredded PET was also added to the concrete mixture to improve the HCS strength. The cast-in-site HCS could be constructed without any difficulties. Three parameters were investigated: the effects of void content, shredded PET content, and steel-fiber (SF) content on the HCS ultimate bending capacity (Mu). Fifteen specimens were tested under …

Numerical Study Of A Buckling Restrained Brace (Brb) In Steel Structures And Comparison With A Convergent Ordinary Brace (Ocb) Under Static And Dynamic Loading, Fatemeh Habibpour

Makara Journal of Technology

Bulk metallic glass (BMG) has good mechanical strength, high hardness, wear resistance, and corrosion resistance with promising application in various industries. However, for the industrial production of BMG, the main issue is how to overcome limitations of joining with other materials. The present study focuses on solder processing at low operating temperature to avoid exceeding the recrystallization temperature. A feasible joining process for BMG was developed using lead-free solders. The BMG surface is pre-plated with copper, nickel, or titanium as a wetting layer. The reaction temperature is set between the glass transition temperature of BMG and the melting point of …

Advanced Concrete Composites For Improved Performance: A Bibliometric Survey, Dhruv Patel, Aryan Tiwari, Nishnat Nikhare, Rohit Shinde, Ashutosh Dubey, Manan Shah, Shalaka Hire, Sayali Sandbhor

Library Philosophy and Practice (e-journal)

Concrete is the core component of any civil engineering construction. Conventional concrete can be modified depending upon the needs and requirements of the construction. Such concrete is called advanced concrete and this report aims to study advanced concrete and its composites. The main objective of this report is to perform a bibliographic survey on the latest research literature available under the domain of advanced concrete composites for improved performance. Timespan considered for the survey is from the year 2015 to 2020. The bibliographic survey consists of literature from online platforms such as the Web of Science (WoS) and Scopus database. …