Structural Engineering Commons^™

Crack Control And Bond Performance Of Alternative Coated Reinforcements In Concrete, Sachin Sreedhara

All Dissertations

Concrete cracking in structures is a ubiquitous problem which can lead to the deterioration of the structure. Other than affecting the strength aspect of a structure, cracking impacts the serviceability criteria as well. Although cracking phenomenon in any structure is highly inevitable, it has to be minimized in order to maintain a structure’s life effectively. Cracking in reinforced concrete structures is related to the bond strength developed between the bar and the concrete. It also depends on an ability of the bar to resist the stresses due to shrinkage to minimize the crack. Another important aspect is the resistance offered …

The Evacuation Simulation Of Wheelchair Users In A Building Fire: An Initial Dynamic Characterization Of Structural Egress Components, Haley Hostetter

All Theses

People with disabilities are one of the most vulnerable groups involved in building fires. According to the U.S. Fire Administration, in the United States alone, an estimated 700 home fires involve people with physical disabilities each year while over 1700 involve those with mental health disorders. Despite this, the current body of literature shows few studies focused on the evacuation of disabled people. This is a direct result of past and present social injustice on people with disabilities and has resulted in high injury and death rates during fires. To combat this, enrich the literature, and improve their experiences in …

Increasing Strength Of Plywood Shear Walls, Elizabeth Claypool, Michelle Dennin

Architectural Engineering

In a recent iteration of an upper-division engineering design lab course at Cal Poly SLO, students were challenged to identify and understand the probable failure mechanism of conventionally built plywood shear walls and hypothesize how they could delay or prevent common failure mechanisms to increase the overall lateral load capacity. After observing the results of a test on a conventional, code specified wall, a solution to integrate metal gauge strapping into edge nailing was developed to address the common failure mechanisms of nail head pull through and panel edge tear out. A shear wall with metal strapping installed between the …

A Review Of Current Construction Guidelines To Inform The Design Of Rammed Earth Houses In Seismically Active Zones, David Thompson, Charles Augarde, Juan Pablo Osorio

Articles

Sustainability in the materials we use for construction is a prime concern, focusing on reducing the embodied energy and carbon footprints of the materials used. The cement used in concrete products is responsible for a significant proportion of Man's CO2 emissions and its production requires substantial energy input, as do fired clay products. For this reason, products formed from unfired earthen materials are of increasing interest and the current challenges include devising means of robust design for strength and to address durability concerns. One form of earthen construction that employs an in-situ method is rammed earth, and it is a …

The Living Breakwaters Pdr Efforts: Conceptual Scheduling, Calvin O. Walters Jr.

Publications and Research

On October 29, 2012, Superstorm Sandy caused nearly $19 billion in damages in New York City including 69,000 residential units across the five boroughs. This disaster precipitated a post-disaster-rebuilding (PDR) project including roughly $4.2 billion in a Community Development Block Grant allocated towards PDR projects. A portion of the grant was used to construct a living breakwater in Tottenville, Staten Island, consisting of a resiliency approach to risk reduction through erosion prevention, wave energy attenuation, and enhancement of ecosystems and social resiliency to improve resistance to storms for the community of Tottenville. The ridges of each breakwater are designed with …

Port Infrastructure Resilience Through Combined Wind-Surge Demand Characterization, Kaley Callaway

Graduate Theses and Dissertations

The United States economy is reliant on maritime transportation for 70% of imports and exports. Structures that are integral to the operation of ports, such as cranes, are jeopardized when tropical storms approach land. While wind is the only environmental load used to design dockside container cranes, storm surge often accompanies severe wind events and can create large structural loads. This study focuses on determining coupled storm-surge demands and the effect of waves on dockside container cranes. A damage index prediction tool that considers both maximum wind speed and storm surge height is developed and applied to historical hurricane data …

Refining Particle Size Specification For Asphalt Emulsion, Pedro Luis Diaz Romero

Graduate Theses and Dissertations

Pavements begin to deteriorate as soon as they are constructed, and traffic is released. The rate at which a pavement deteriorates depends on the material quality, the environment, and the loads carried. To properly preserve pavements and extend their life, various pavement preservation treatments are used. For flexible pavements, a considerable number of these treatments use asphalt emulsion (which are refer to simply emulsions from here on). Emulsions are classified based on their particle charge and reactivity. Emulsions used in chip seals are usually of rapid set reactivity and are classified based on tests over fifty years old.

It has …

Cyclic Behavior Of Laterally Skewed Special Moment Frame Connections: Experimental Testing And System-Level Analyses, Mohammad Hossein Kashefizadeh

Graduate Theses and Dissertations

Special moment frames (SMFs) are frequently used in high seismic areas for architecturally constrained designs. SMFs provide lateral system stiffness without the use of braces that often obstruct views and architectural features. Current American Institute of Steel Construction (ASIC) provisions (AISC 341-16) provide prequalified SMF connection details; however, all prequalified details only consider orthogonal connections between the beam and column. This dissertation investigates the effect of adding skew within SMF beam-to-column connections. The study presented herein involves system-level dynamic time-history analyses of skewed SMF connections, the analytical component-level investigation into the effect of the concrete slab on behavior of the …

Validation Of Cfd Tornado Pressure On Building And Wind Field With Ttu Vortex Chamber Measurements, Sumit Verma

Graduate Theses and Dissertations

Structural failure of low-rise buildings is the root cause of higher number of casualties, death tolls and economic losses at the place of occurrence of tornadoes. Proper design of low-rise buildings in tornado-prone areas require accurate estimation of tornado-induced wind loads; however, exhaustive research to estimate the wind loads reliably on buildings during tornadic events is still lacking. Several studies have been carried out to investigate the magnitude of forces induced by tornado winds on buildings from experimental as well as computational side. However, the wind pressures obtained on the building from different experimental studies have shown significant variation from …

Wave Interactions And Energy Cascade, Bailey Downing

Civil Engineering Undergraduate Honors Theses

Structural engineers design buildings and their components to withstand code-specified wind loads. The ASCE 7-16 manual sets the standards for calculating wind loads in the U.S. Depending on the velocity of wind, deflections may occur as wind passes through the building. The pressure reported from ASCE are based on wind tunnel measurements. The peak pressure from ASCE 7 is much less than what is measured from the field for a low-rise building. As an alternative economic tool, Computer modeling has been developed to help with this dilemma. Methods based on computational fluid dynamics (CFD) are used to calculate velocities and …

Strain Measurements In Skewed Reduced Beam Section Special Moment Frame Connections, Elizabeth Moriconi

Civil Engineering Undergraduate Honors Theses

A series of experimental tests were conducted in the Civil Engineering Research and Education Center (CEREC) at the University of Arkansas to evaluate the effect of beam skew on a reduced beam section. Various degrees of skew on deep and shallow column depths were tested following a cyclical loading protocol, established by the AISC Seismic Provisions, to analyze the capacity of the out-of-plane skew connection [1]. Using the prequalified cyclical loading protocol allows for the evaluation of SMF connections in skew configurations against seismic events. Strain distributions throughout the RBS section, the welded beam-column connection, and the column flange were …

Comparing The Stiffness Of Cold In-Place Recycled Asphalt Pavement To Hot Mix Asphalt: Determining The Reproducibility Of The Stiffness Rebound Test, Tanner Turben

Civil Engineering Undergraduate Honors Theses

The Stiffness Raveling Mechanism Test (SRMT) was originally developed as an indirect measure of pavement stiffness to determine a pavement’s tendency to ravel, a type of damage. Regarding rehabilitation of existing roadways by Full Depth Reclamation (FDR) Cold In-Place Recycling (CIR), concern of field repeatability was expressed (Hill & Braham, 2016).

An analysis of lab-compacted samples of CIR and Hot Mix Asphalt (HMA) was performed to determine if the results could be reproduced between CIR and HMA. Additionally, the experiment observed the effects of percent air voids, temperature, and moisture conditioning on CIR and HMA. Three samples were prepared for …

Evaluating The Effects Of Curing Methods On Bcsa Cement Concrete, Hannah Allen

Civil Engineering Undergraduate Honors Theses

BCSA cement is a type of cement that makes concrete set up much quicker than typical portland cement concrete. BCSA cement concrete also has a much higher compressive strength than that of portland cement concrete. This study was conducted to determine the effect of different curing conditions on the compressive strength of BCSA cement concrete.

Control Strategy For Solar Energy-Saving Lamps For Optimized Energy Utilization And Sustainability Of Operation Durability: Indonesia Case, Burhanuddin Halimi, Agus Purwadi, Nana Heryana

Makara Journal of Technology

To solve the electrification ratio issue, the Indonesian government has promoted the use of solar energy-saving lamps. This study proposes a control strategy that adopts current reference time-based profiling for solar energy-saving lamps. For optimal energy consumption, the current reference profile is determined according to users’ daily energy requirements. From the aspect of user comfort, a gradual step reference profile is also introduced to provide a subtle change in lighting intensity level. The proposed control strategy can minimize energy consumption and optimize the operation durability of the system. The concept is verified by simulating four scenarios, the results of which …

Mechanical Behavior Of Clay Soil Stabilized With Fly Ash And Bottom Ash, Soewignjo Agus Nugroho, Azra Zulnasari, Ferry Fatnanta, Andius Dasa Putra

Makara Journal of Technology

Soil is one of the most important aspects of an infrastructure given its functions of receiving and holding structural loads. However, not all soils have good physical and mechanical properties. To overcome those conditions, stabilization of the soil is practiced to meet the technical requirements. This study aims to determine the behavior of high plasticity clay stabilized with lime, fly ash, and bottom ash. These additives can be used as a stabilizing agent to increase soil strength. The percentage of additives varied from 5%–25% then mixed with clay and were tested through the (Unconfined Compression Strength (UCS) test. The UCS …

Enhancement Of Biogas Production Through Solid-State Anaerobic Co-Digestion Of Food Waste And Corn Cobs, Lukhi Mulia Shitophyta, Anisa Salsabila, Firanita Angraini Putri, Siti Jamilatun

Makara Journal of Technology

Although biogas has been primarily produced through liquid anaerobic digestion, this method leads to the floating and stratification of fibers and non-homogeneous mixing, which can reduce the biogas yield. Alternatively, biogas can be produced by the solid-state anaerobic digestion (SS-AD) of organic material with a high solid content, such as corn cobs. We investigated the co-digestion of food waste and corn cobs as a biomass feedstock for SS-AD in biogas production. We measured the effects of the total solid (TS) content, percentage of food waste, and reduction in volatile solids (VS), from which we determined its appropriate kinetic model. We …

A Case Study Of Protecting Bridges Against Overheight Vehicles, Aly Mousaad Aly, Marc Hoffmann

Faculty Publications

Most transportation departments have recognized and developed procedures to address the ever-increasing weights of trucks traveling on bridges in service today. Transportation agencies also recognize the issues with overheight vehicles’ collisions with bridges, but few stakeholders have definitive countermeasures. Bridges are becoming more vulnerable to collisions from overheight vehicles. The exact response under lateral impact force is difficult to predict. In this paper, nonlinear impact analysis shows that the degree of deformation recorded through the modeling of the unprotected vehicle-girder model provides realistic results compared to the observation from the US-61 bridge overheight vehicle impact. The predicted displacements are 0.229 …

Optimizing The Self-Healing Efficiency Of Hydrogel Encapsulated Bacteria In Concrete, Ricardo Hungria

LSU Master's Theses

Calcium carbonate precipitation through microbial means is a promising pathway for concrete self-healing technologies, mainly for its microcrack sealing attributes. The main goal of this project was to study and optimize the crack healing efficiency of hydrogel encapsulated bacteria in concrete. To achieve this purpose, Bacillus pseudiformus was implemented as the bacteria strain at a concentration of 10⁸ cells/ml. This bacterium strain along with yeast extract was combined along with three different mineral precursors corresponding to magnesium acetate, calcium lactate, and sodium lactate. All these three precursors were evaluated at two concentrations (67.76 mM/l and 75 mM/l). For each …

Cost-Efficient Bridge Scour Health Monitoring Using Commercial Sensors, Connor Embleau, Tien Yee, Metin Oguzmert, Mahyar Amirgholy, Alan Akazemi, Dale Goff

Symposium of Student Scholars

Bridge scouring has been a major international issue regarding bridge health and the overall longevity of a bridge. A common bridge health concern such as scouring accounts for close to 60% of bridge failures in the United States and is a leading cause to a bridge being in critical condition. Traditional methods to combat this failure is to measure the scour depth to assess a bridge health. Due to safety concerns of the traditional method, this study proposes to monitor a bridge’s health using a vibration-based technique. At present, vibration-based techniques have yet to be utilized reliably in the field. …

Reducing Early-Age Shrinkage Cracks Of Bridge Decks And Rails, Soumitra Das, George Morcous, Jiong Hu

UNL Student Research Days Posters, Graduate

Early-age shrinkage cracking of concrete bridge decks and rails accelerates the penetration of water and chemicals which leads to reinforcement corrosion, delamination, and eventually spalling. All this results in shorter service life, road closure, and costly repair. Development of Low-cement concrete(LCC) mix to reduce early age shrinkage crack through aggregate grading optimization was done in this research work. This approach also reduces concrete cost ($15-$20/cyd) (15–25%) and its carbon footprint (≈15%).

Blast Analysis Of Steel-Plate Composite Slabs: Sdof And Fem Analyses, Joshua R. Harmon, Amit H. Varma

Bowen Laboratory Research Reports

Steel-plate composite (SC) members have emerged as competitive construction methods for tall buildings and nuclear power plants. Detailed design guidance has been created for these functions and design of these members is now covered in AISC 341-16 and ASIC N690-18. However, SC members are emerging for use in protective structures to withstand blast and impact loads. Although experimental tests of SC members for blast resistant design have been conducted, design of SC members for blast loads has not been addressed in existing design references for blast loadings (UFC 3-340-02). This report details a general design philosophy for blast loaded SC …

North 14th Street Corridor Improvements Project, Ashley Nguyen, Samantha Corey, Maricela Paramo Reyes, Pooja Rajeev

Honors Program: Senior Projects (Public)

The following project report was a study of the North 14^th Street corridor ranging from Adams Street to Virginia Street conducted by University of Nebraska-Lincoln students for a senior design capstone project. Main focuses of the project were the intersection of Adams and 14^th Street and the 14^th Street bridges over Cornhusker Highway and Oak Creek. Study of this area included work in transportation, traffic, structural, geotechnical, water resources, and environmental engineering. However, this report done by students should not take the place of work done by licensed professional engineers.

This project was done in collaboration with …

Analysis Of Shear Failure In Ultra-High Performance Concrete Beams, Kevin Conway

Electronic Theses and Dissertations, 2020-2023

Ultra-high performance concrete (UHPC) is an emerging cementitious material type currently undergoing research in different structural applications. This material is characterized by a compressive strength of 150 MPa (22 ksi), according to the Association Francaise de Genie Civil and the Federal Highway Administration, high tension strength, and high durability. Additionally, UHPC consists of secondary reinforcement in the form of steel or polymeric fibers, which enable UHPC to exhibit tension hardening behavior and tension ductility previously ignored in conventional concrete mixes. Previous research has focused on applications in the transportation and bridge design industries; however, applications in buildings and other heavy …

Finite Element Method Calculation Of A Prestressed Self Consolidating Concrete Beam, Vladyslav Machulsky

Graduate Theses, Dissertations, and Problem Reports (ETD)

In this study, a prestressed concrete box beam produced for the Stalnaker Run Bridge (SRB) replacement project using self-consolidating concrete (SCC) was simulated using finite element method (FEM) numerical technique. ANSYS, a commercial FEM software, was used to build the prestressed SCC box beam model. The FEM model was developed to understand the behavior of concrete and steel under prestressing loads, long-term effects, and superimposed loads. The SOLID65 and REINF264 element types were chosen to simulate the behavior of concrete and steel materials. Experimentally measured mechanical properties of concrete from the SRB project were used in the analysis allowing for …

Expanding The Applicability Of Press-Brake-Formed Tub Girders Through The Extension Of The Maximum Span Length And The Evaluation Of Pier Continuity, Robert M. Tennant

Graduate Theses, Dissertations, and Problem Reports (ETD)

The Short Span Steel Bridge Alliance (SSSBA) is a group of bridge and buried soil steel structure industry leaders who provide educational information on the design and construction of short-span steel bridges in installations up to 140 feet in length. Within the SSSBA technical working group, a modular, shallow press-brake-formed tub girder (PBFTG) was developed to address the demand in the short-span steel bridge market for rapid infrastructure replacement solutions. PBFTGs consist of modular, shallow, trapezoidal boxes fabricated from cold-bent structural steel plate. A concrete deck, or other deck option, may be placed on the girder, and the modular unit …

Comparative Analysis Of Bridge Abutment Types, David Fell

Williams Honors College, Honors Research Projects

This project was developed to serve as a brief overview of design practices and considerations in the selection of highway bridge abutment types. This involved a review of literature in the form of reviewing national design guides and department of transportation (DOT) requirements from both US DOTs and international DOTs. The abutment types covered in this research included conventional reinforced concrete abutments with bearings, integral abutments, and semi-integral abutments. This research focused solely on highway bridge abutments, particularly on Ohio Department of Transportation design requirements due to their extensive use of semi-integral abutments. Superstructure elements and geometric requirements are primary …

Sustainability And Environmentally Friendly Methods To Travel Over Waterways, Kendall Kubus

Williams Honors College, Honors Research Projects

Throughout daily traveling, the main structures used are bridges and tunnels. Bridges are used as overpasses over valleys, canyons, and areas that require a large amount of dirt fill to bring the roadway up to the proper grade. Tunnels are underpasses through mountains, under city limits and waterways. The benefits of building a bridge structure is little preparation goes into earth-work and the transportation of aggregate materials. There is some time spent testing surrounding soil to determine the process that will need to occur for foundation preparations in bridge columns. Options for foundation include different types of drilled shafts, caissons, …

Review Of Innovative Rehabilitation Techniques For Reinforced Concrete Buildings, Demetrius Karoubas

Graduate Theses, Dissertations, and Problem Reports (ETD)

Building rehabilitation encompasses the act of repairing damaged structural elements, as well as the upgrading of older buildings to bring them up to modern standards. In recent years, due to the extreme economic and environmental cost of new construction, building rehabilitation is gaining ground as the most viable solution to the problem posed by damaged or substandard buildings. With the constant development of new materials with favorable properties and the improvement of our understanding of earthquakes, new rehabilitation techniques are being developed, improving on the efficiency and effectiveness of older ones. Reinforced Concrete (RC) buildings are a type of building …

Experimental And Design Evaluation Of Multi-Bolted Gfrp Joints, Amir Hossein Houshmandyar

Graduate Theses, Dissertations, and Problem Reports (ETD)

For infrastructure system implementation, high strength/stiffness to self-weight ratio, corrosion resistance and ease of fabrication are just a few of the many advantages of pultruded fiber reinforced polymer (PFRP) composites over traditional construction materials. However, challenges of engineered FRP materials are addressed via continuous updating of design codes. For example, the anisotropic nature of FRP composite materials includes different mechanical properties in different directions (pull or longitudinal direction vs. transverse to pull direction) of a structural member, resulting in design complexities over isotropic materials. Typically, infrastructure systems are built by bolting FRP structural members because of certain advantages of bolted …

Numerical Assessment Of Post-Tensioned Slabs Due To Seismic Column Collapse, Mariam Ehab, Aya Elhozayen

Civil Engineering

In our recent catastrophes, Progressive collapse become an essential behavior that should be researched widely and to be considered by engineers through the design process. The main vertical loss can be caused by different reasons, either blast due to terrorist attack, failure of columns due to extreme earthquake application, or finally, losing a structural element due to high impact resulted from a vehicle or any other moving object. Losing main vertical element due to extreme earthquake excitation is an important and repeated occurrence, However, it didn’t take much attention in progressive collapse recent studies. Unified Facilities Criteria (UFC) and General …