Structural Engineering Commons^™

Benchmark For Country-Level Earthquake Strong-Motion Instrumentation Program, Widjojo Adi Prakoso, I Nyoman Sukanta

Makara Journal of Technology

An empirical study to develop benchmark models at country-level to assess the suggested number of earthquake strongmotion stations based on a framework encompassing geographic, demographic, and socio-economic parameters is reported. The models are to provide a working estimate of the required number of stations for improving the strongmotion instrumentation program of Indonesia. National earthquake strong-motion networks of New Zealand, Japan, Taiwan, Iran, Turkey, and Italy were used as the references. The parameter proposed is the number of stations in land area of 1,000 km2, and three models based on the exponential regression analysis are presented as functions of population density, …

Worst Case Of Relative Disturbance Gain Array For Uncertain Distillation System, Rudy Agustriyanto, Jie Zhang

Makara Journal of Technology

This article discusses the constrained nonlinear optimization formulation for calculating the worst case of lower and upper bounds of relative disturbance gain array (RDGA) for uncertain process models. The proposed approach seeks the minimum and maximum values of the relative disturbance gains subject to the constraints in which the process and disturbance gains are within their uncertainty ranges. RDGA ranges are useful for control structure determination and the related robustness, as they provide information regarding the sensitivity to gain uncertainties. The proposed method is demonstrated by ternary distillation column case study. Closed loop simulation results support the analysis based on …

Biodiesel Production From Waste Cooking Oil Using Hydrodinamic Cavitation, Muhammad Dani Supardan, Satriana Satriana, Mahlinda Mahlinda

Makara Journal of Technology

The aim of this research was to study biodiesel production from low cost feedstock of waste cooking oil (WCO) using hydrodynamic cavitation apparatus. A two-step processes esterification process and transesterification process using hydrodynamic cavitation for the production of biodiesel from WCO is presented. The first step is acid-catalyzed esterification process for reducing free fatty acid (FFA) content of WCO and followed by base-catalyzed transesterification process for converting WCO to biodiesel as the second step. The result of esterification process with methanol to oil molar ratio of 5 and temperature of 60 oC showed that the initial acid value of WCO …

Knowledge Dictionary For Information Extraction On The Arabic Text Data, Wahyu Syaifullah Jauharis Saputra, Agus Zainal Arifin, Anny Yuniarti

Makara Journal of Technology

Information extraction is an early stage of a process of textual data analysis. Information extraction is required to get information from textual data that can be used for process analysis, such as classification and categorization. A textual data is strongly influenced by the language. Arabic is gaining a significant attention in many studies because Arabic language is very different from others, and in contrast to other languages, tools and research on the Arabic language is still lacking. The information extracted using the knowledge dictionary is a concept of expression. A knowledge dictionary is usually constructed manually by an expert and …

Effects Of Deposition Parameters And Oxygen Addition On Properties Of Sputtered Indium Tin Oxide Films, Badrul Munir, Rachmat Adhi Wibowo, Kim Kyoo Ho

Makara Journal of Technology

Indium tin oxide (ITO) films were sputtered on corning glass substrate. Oxygen admixture and sputtering deposition parameters were optimized to obtain the highest transparency as well as lowest resistivity. Structural, electrical and optical properties of the films were then examined. Increasing deposition rate and film thickness changed the crystallographic orientation from (222) to (400) and (440), as well as higher surface roughness. It was necessary to apply substrate heating during reposition to get films with better crystallinity. The lowest resistivity of 5.36 x 10-4 Ω•cm was obtained at 750 nm film thickness. The films’ resistivity was increased by addition of …

The Effect Of Rubber Mixing Process On The Curing Characteristics Of Natural Rubber, Abu Hasan, Rochmadi Rochmadi, Hary Sulistyo, Suharto Honggokusumo

Makara Journal of Technology

This research is aimed at studying the relationship between rubber mixing processes and curing characteristics of natural rubber. The curing characteristic analysis was carried out through a natural rubber formula having been masticated and mixed, followed by curing. As many as four mastication methods were finely applied; each respected four sequences of rubber mixing process. In the first method, rubber was masticated for 5 minutes and then rubber chemicals and carbon black N 330 were simultaneously added. In the second and the third methods, rubber was masticated for 1 minute and then carbon blacks and rubber chemicals were also simultaneously …

Improved Optical Probe For Measuring Phytoplankton Suspension Concentrations Based On Optical Fluoresensce And Absorption, Retno Wigajatri Purnamaningsih, Nining Betawati Prihantini

Makara Journal of Technology

This paper discusses the results of improved optical probe that works according to optical fluorescence and absorption phenomena for measuring the phytoplankton suspension concentrations. Measurements are made on the Scenedesmus sp. culture. The laboratory test has shown that range of concentration from 104 up to around 1 x 106 cells/mL; fluorescence intensity at λ = 685 nm; and logarithmic of transmission intensity at λ = 405 nm are proportional to the cell concentration linear with proportional constant γ = 4 × 10-5 and β = –2 × 10-7 mL/cell respectively.

Mechanical And Thermal Properties Of Polypropylene Reinforced By Calcined And Uncalcined Zeolite, Nurdin Bukit

Makara Journal of Technology

This study was carried out to compare mechanical and thermal properties of polypropylene (PP) reinforced with uncalcined and calcined zeolites. The PP samples were reinforced with zeolites at various quantities of 2, 4, and 6 (wt %). The comparison of the two types of zeolite was based on mechanical properties, including tensile strength, elongation at break, and Young’s modulus, and thermal characteristics analyzed using DSC, and DTA/TGA technique. The results obtained clearly revealed that both zeolites were able to significantly increase tensile strength and Young’s modulus of the samples, with calcined zeolite was found to work better. Addition of calcined …

Observation Of Center Disaster Damage On Pariaman And Wasior Using Differential Sar Interferometry (Dinsar), Dodi Sudiana, Mia Rizkinia

Makara Journal of Technology

This study focuses on disaster observations in Pariaman (West Sumatera) and Wasior (Papua) using remote sensing techniques (differential SAR interferometry). Differential interferometry (DInSAR) method was performed on two PALSAR data sets with different acquisition months, i.e. about a month after and before disaster, respectively. The center damage of Pariaman earthquake and Wasior flood can be determined by deriving Land Subsidence using DInSAR method.

Physico-Chemical, And Sensory Properties Of Soy Based Gouda Cheese Analog Made From Different Concentration Of Fat, Sodium Citrate And Various Cheese Starter Cultures, Abu Amar, Ingrid Suryanti Surono

Makara Journal of Technology

Gouda cheese analog (GCA) was made using soy protein isolate (SPI), skim milk powder (SMP), fat (palm fat and butter fat), and water (W) at optimal ratio of SPI : SMP : F : W = 14 : 6 : 20 : 60. The effects of butter fat, sodium citrate, and cheese starter culture on the sensory properties of ripened product were assessed by preference test, hedonic test, and the texture profile analysis (TPA) of GCA. The free fatty acids, water-soluble nitrogen, and reduction in pH value of progel were also measured. The use of 100% butter fat (BF) produced …

Development Of Local-Economic-Development Small And Medium Industries (Led-Sme) In East Java, Rachmad Hidayat, Sabarudin Akhmad

Makara Journal of Technology

This paper presents the effects of Indonesian government’s developmental efforts of assistance and training performed on the growth of LED-SME business units and business performance. Both parameters of the government’s assistance and training were used to analyze the impact to the growth and performance of business unit. To achieve a comprehensive result, samples acquired in this research were about 190 entrepreneurs and managers of LED-SME from East Java. Based on the parameters above, there are five hypotheses made to prove the relationship of the assistance and training to the growth and performance of business units. The structural equation modeling (SEM) …

Probabilistic Analysis Of Indeterminate Highway Bridges Considering Material Nonlinearity, Liam Mccarthy

Masters

With ever-reducing maintenance budgets and ever-deteriorating bridge infrastructure, th assessment of existing bridges is vital. Reliability analysis techniques are becomin increasingly popular in the structural safety assessment of existing bridge structures Commonly, a component based approach is used in reliability analysis techniques Traditional reliability procedures often employ a conservative definition of failure, in that th component is deemed to have failed when the strength capacity has been exceeded at a singl cross section. As a result, the component's degree of redundancy and ductility is ignored giving an often conservative estimate of the load carrying capacity of the bridge component Therefore, …

Structural Performance And Economics Of High-Rise Buildings Under Seismic And Wind Loads, Nadeem Hussain

Theses

High-rise buildings have a priority when considering the potential consequences from natural hazards since they represent concentrated human and monetary assets. The use of high strength materials is promoted in this class of structures to effectively use floor areas, control vibrations and expedite construction. There is a pressing need to investigate the relationship between structural performance and economics of high-rise buildings with different material strengths under lateral loads, particularly seismic loads that control the design of a wide range of buildings.

To realistically represent the modern high-rise construction, five 60-story reinforced concrete (RC) buildings with varying material strengths, ranging from …

The Effects Of Bolt Pretension, In-Plane Eccentricity, And Friction On The Ductility Of Block Shear Connections, Kevin M. Zmetra

Master's Theses

Block shear is a complex failure mechanism in bolted and welded steel components such as gusset plates, webs of coped beams, angles and tees. It presumes a combination of tension rupture and shear yield. Multiple variables affect the block shear capacity and ductility of a connection. This study investigates the effects of bolt pretension, connection eccentricity and friction force transfer through a series of destructive experiments followed by refined finite element simulation. Clamping forces create a complex triaxial stress field compounded by the stress concentration at the bolt holes. In-plane load eccentricity with respect to the centerline of the connection …

Laboratory Performance Of Highway Bridge Girder Anchorages Under Simulated Hurricane-Induced Wave Loading, Jora Lehrman, Christopher Higgins, Daniel Cox

TREC Final Reports

Many bridges along the Gulf Coast of the United States were damaged by recent hurricanes, and many more are susceptible to similar damage. This research examines the structural performance of common connection details used to anchor prestressed concrete girders to the substructure. Full-scale specimens were fabricated and tested under static and dynamic cyclic load histories. Dynamic load histories were developed from previously conducted hydraulic tests of a 1/5 scale model of a highway bridge under hurricane wave loads. The load effects considered included the pseudo-statically applied vertical uplift force, horizontal force, combined horizontal and vertical forces, and dynamically applied combined …

Development Of System Reliability Models For Railway Bridges, Anna Maria Rakoczy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Performance of the railway transportation network depends on the reliability of railway bridges, which can be affected by various forms of deterioration and extreme environmental conditions. More than half of the railway bridges in US were built before 1950 and many show signs of distress. There is a need for efficient methods to evaluate the safety reserve in the railway bridges by identification of the most sensitive parts of the bridge.

An accurate estimation of remaining fatigue life of a structural component is very important in prioritizing bridge rehabilitation and replacement. However, existing procedures to evaluate the fatigue behavior of …

Effects Of Alternate Cementitious Materials On Compressive Strength And Environmental Impacts Of Cement Mix Designs., Mitchell R. Bush

Materials Engineering

Specific proportions of Portland cement, fly ash, and blast furnace slag cement mixtures where chosen by a ternary phase diagram to be investigated. By experimental testing and company data history fly ash was limited to not exceed 30% and contribution of Portland cement must be over 50%. Ten chosen mix designs were batched by following ASTM C305-94 and cured for twenty-eight and forty-two days, the extended cure length allows the reaction of pozzolanic material with calcium hydroxide to complete. Compressive strength testing at forty-two days yielded low strength for mix designs with 20% or less Portland cement compared to our …

Seismic Hazard Assessment Of Oregon Highway Truck Routes, Peter Dusicka, Selamawit Tesfayesus Mehary

TREC Final Reports

This research project developed a seismic risk assessment model along the major truck routes in Oregon. The study had adopted federally developed software tools called Risk for Earthquake Damage to Roadway Systems (REDARS2) and HAZUS-MH. The model was the first time REDARS2 has been adopted and used in research outside of the original development team, presenting a number of unique challenges. The development of the model was a complex, intensive process that required a significant research effort, manipulation and adjustment of data. Furthermore, limitations of the software tools themselves had been identified that prevented the inclusion of important aspects such …

Short Term Monitoring Of Suspender Cables On An In-Service Highway Bridge, Gannon Stromquist-Levoir

Master's Theses

No abstract provided.

Computer-Aided Engineering Tools For Structural Health Monitoring Under Operational Conditions, Priscilla O. Mensah-Bonsu

Master's Theses

This thesis presents two different applications of computer-aided non-destructive approaches for structures monitored under operational conditions. The first part of the thesis is the development of a graphical user interface (GUI) software for real-time autonomous assessment of structural health condition based on the signature vibration properties of the structure under study. The program, called ConImote2, operates on the wireless sensor network platform called imote2. ConImote2 is created in the Matlab platform for accessibility and to enable extension of its capabilities by the user. The primary goal of creating the program is to overcome the issue of data inundation from SHM …

Developing A Family Of Curves For The Hec-18 Scour Equation, Timothy Calappi, Carol J. Miller, Donald Carpenter, Travis Dahl

Civil and Environmental Engineering Faculty Research Publications

Accurate pier scour predictions are essential to the safe and efficient design of bridge crossings. Current practice uses empirical formulas largely derived from laboratory experiments to predict local scour depth around single-bridge piers. The resulting formulas are hindered by insufficient consideration of scaling effects and hydrodynamic forces. When applied to full-scale designs, these formula deficiencies lead to excessive over prediction of scour depths and increased construction costs. In an effort to improve the predictive capabilities of the HEC-18 scour model, this work uses field-scale data and nonlinear regression to develop a family of equations optimized for various non-cohesive soil conditions. …

Safety Investigation And Guidance For Retrofitting Existing Approach Guardrail Transitions, Eric R. Jowza

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Throughout the United States, various approach guardrail transition systems are routinely implemented by State Highway Departments to connect standard strong-post, W-beam guardrail systems to the blunt end of concrete bridge rails and roadside median barriers. When installed correctly, approach guardrail transitions shield the hazardous exposed ends of rigid parapets as well as significantly reduce the propensity for wheel snag and vehicle pocketing throughout the transition region. Unfortunately, approach guardrail transitions that are installed in the field may not always resemble that of the as-tested configuration, thus reducing the desired lateral stiffness and strength of the transition system. A recent survey …

Transversely Post-Tensioned Box-Beam System For Precast Parking Structures, Jenna Hansen

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Parking structures are essential to any growing commercial district, yet little thought is given to their longevity and appearance. This is particularly the case with precast parking structures. Typical issues include poor joint performance and the impact of stemmed members on interior building aesthetics. Research provided in this report proposes an alternate design that improves long term joint performance and optimizes the perspective spacing between deck members. These benefits (along with the others) are incorporated to reflect the benefits of parking structures designed using cast-in-place concrete and structural steel with concrete decking. Other benefits include: flexible column spacing, reduced / …

Efficient Precast/Prestressed Floor System For Building Construction, Eliya E. A. Henin

Department of Construction Engineering and Management: Dissertations, Theses, and Student Research

Precast floor systems provide a rapidly constructed solution to multi-story buildings that is economical, high quality, fire-resistant, and with excellent deflection and vibration characteristics. Conventional precast concrete floor system cannot compete with cast-in-place post tensioning flat slab floor systems when high span-to-depth ratio and flat soffit are required. This is due to the significant depth of standard precast beams, and use of column corbels and beam ledges. This research presents the development of a new precast concrete floor system that eliminates the limitations of conventional precast floor system and provides a competitive precast alternative to cast-in-place flat slab floor systems. …

Monitoring And Modeling Of The Hydraulic And Sediment Processes At In-Stream Restoration Structures In The Vicinity Of A Bridge Crossing, Brian P. Schultz

Master’s Theses

The long-term performance of infrastructure depends on reliable and sustainable designs. Many of Pennsylvania’s streams experience sediment transport problems that increase maintenance costs and lower structural integrity of bridge crossings. A stream restoration project is one common mitigation measure used to correct such problems at bridge crossings. Specifically, in an attempt to alleviate aggradation problems with the Old Route 15 Bridge crossing on White Deer Creek, in White Deer, PA, two in-stream structures (rock cross vanes) and several bank stabilization features were installed along with a complete channel redevelopment. The objectives of this research were to characterize the hydraulic and …

Bond Performance Of Lightweight Self-Consolidating Concrete, Michael Howland

Civil Engineering Undergraduate Honors Theses

Self-consolidating concrete (SCC) allows for the placement of concrete without consolidation. The use of lightweight (LW) concrete reduces dead loads and lowers transportation costs. LWSCC is a recent combination of the two types of concrete; therefore there is little information on the performance of prestressed members cast with LWSCC. This project examines transfer length of LWSCC beams and compares the measured values to control-mixture members cast with normal weight SCC. Eight prestressed beams were cast. Of the eight, four conventional were cast with SCC and the remaining four with LWSCC. The lightweight mixtures contained expanded clay aggregate and had an …

Full Depth Reclamation: Compaction And Moisture Content, Alexander Jackson

Civil Engineering Undergraduate Honors Theses

Many times a road will fail and will be in need of both a structural increase and a repair. Full Depth Reclamation (FDR) is a road rehabilitation technique able to offer both. This method also has a lower total cost and significantly lower material usage than traditional overlaying repair methods. FDR is a road repair method which mills up the current road down into the subgrade, and then stabilizes and compacts the milled material. This is also useful for correcting deeper problems in the road structure which are not addressed by traditional methods. In this study, three different suggestions of …

Structural Performance Of Reinforced Concrete Flat Plat Buildings Subjected To Fire, Sara Jean George

UNLV Theses, Dissertations, Professional Papers, and Capstones

Reinforced concrete structures are typically considered to have inherent resistance to fire. However, several concrete structures around the world have experienced partial or total collapse under fire. Reinforced concrete flat-plate is a type of structural system widely used for office and residential buildings. Flat plate construction is prone to punching shear failure at slab-column connections which may lead to a catastrophic progressive collapse. The slabs of flat-plates generally have very thin concrete cover leaving steel reinforcement more sensitive to thermal loads. Little is known in the engineering community about the structural performance of flat-plate structures subjected to fire. Through a …

Smart Home Prototype, Logistics & Planning, David G. Guzman^, Virgilio Gonzalez*

COURI Symposium Abstracts, Spring 2012

No abstract provided.

Tolerance Limit For Trucks With Excess Load In Transport Regulation In Indonesia, Sigit Pranowo Hadiwardoyo, Raden Jachrizal Sumabrata, Mohammed Ali Berawi

Makara Journal of Technology

Reliability of a road is mandatory since damaged will impede the traffic. Destruction is caused by various factors; one of the most important factors is excess load. Overload may give the load of each axle of a vehicle exceeds the determined standard. This condition occurs in trucks exceeding the load limit. In designing the structure of a road based on the method of Directorate General of Highways Ministry of Public Works of the Republic of Indonesia, axle load calculated in equivalent-number, or known as equivalent axle load (EAL), of 8.16 tons of standard axle. Total equivalent-number over the service life …