Geotechnical Engineering Commons^™

Liquefaction-Induced Dragload And/Or Downdrag On Deep Foundations Within The New Madrid Seismic Zone, Ishimwe Elvis

Graduate Theses and Dissertations

Deep foundation elements are typically used to transfer structural loads for multi-story buildings and large-span bridges to a competent soil layer when 1) the soil close to the ground surface has no sufficient bearing capacity, and when 2) liquefiable soils are encountered. The majority of the bridges constructed within seismic zones rely upon the stability of earthen embankments and deep foundation that are installed above or within liquefiable soil deposits. Despite large factor of safety values or different load and resistance factors being used to adequately design deep foundations within seismic areas, soil liquefaction may cause extensive damage to the …

The Intrinsic Properties Of Reconstituted Soils, Nabeel Shaker Mahmood

Graduate Theses and Dissertations

Reconstituted specimens are often utilized to characterize engineering properties of cohesive soils. A series of undrained triaxial tests were conducted on reconstituted soil specimens to evaluate 1) the influence of stress path, 2) the intrinsic shear strength behavior, and 3) the small-strain characteristics. The stress path tests were conducted on kaolinite specimens reconstituted from slurries with water content values of one and one-half times the liquid limit of the soil (1.5LL). To evaluate the intrinsic undrained shear strength and the intrinsic small-strain properties, the triaxial tests were performed on kaolinite and illite specimens that were reconstituted at two levels of …

Development Of A Hydraulic Conductivity Placement Window Using Centrifuge Techniques, Greg Thomas

Civil Engineering Undergraduate Honors Theses

A centrifuge soil testing device, currently operated by researchers at the University of Arkansas, was used to develop a technique to determine a hydraulic conductivity placement window. The purpose of this research was to develop a placement window by means of a centrifuge instead of by means of a panel board. Soil specimens were created at standard PRcotor energy and at 50 percent of Standard Proctor energy at -3 percent of optimum, -1.5 percent of optimum, two specimens at optimum, +1.5 percent of optimum, and +3 percent of optimum water content. Values of hydraulic conductivity for the respective specimens were …

Development Of An Internal Camera-Based Volume Determination System For Triaxial Testing, Sean Elliott Salazar

Graduate Theses and Dissertations

Accurate measurement of axial, radial, and volumetric strain parameters are critical to the understanding of phase relationships and the constitutive behavior for saturated and unsaturated soils. The use of photographic monitoring techniques for laboratory-based measurement of these parameters have become common. A novel technique that utilized camera instrumentation located within the triaxial testing cell was developed and validated. By placing the instrumentation inside of the cell, instead of the instrumentation being located outside of the cell, the technique eliminated cumbersome corrections required to account for optical distortions due to 1) the refraction of light at the confining fluid-cell wall-atmosphere interfaces, …

Cost-Savings Of Implementing Site-Specific Ground Motion Response Analysis In Design Of Mississippi Embayment Bridges, Ethan Ryan Benton Baker

Graduate Theses and Dissertations

Deep dynamic site characterization and a site-specific ground motion response analysis (SSGMRA) were conducted for a bridge site in Monette, Arkansas. The SSGMRA indicated the design acceleration response spectrum determined using the American Association of State Highway and Transportation Officials (AASHTO) general seismic procedure could be reduced by 1/3 for the short period range due to attenuation of the short-period ground motions. The steel girder pile-bent bridge, originally designed using the AASHTO general seismic design procedure, was redesigned using the updated seismic demands estimated from SSGMRA. A cost-savings analysis was then conducted to determine the potential savings associated with conducting …

An Evaluation Of Borehole Hydraulic Conductivity Equations And Field Determined Soil Water Characteristic Curves, Johnathan Dale Blanchard

Graduate Theses and Dissertations

The methods utilized to determine the hydraulic conductivity of compacted clay liners (CCLs) are of importance for safe guarding the environment from landfill leachate. Therefore, the methods utilized in the analysis of the Two Stage Borehole (TSB) test, as described in the ASTM D6391-11 (Method A, B, and C) standard, were evaluated. Data from hydraulic conductivity tests, as performed on three test pads, were utilized to review the ASTM D6391-11 equations. Additionally, two test pads were instrumented with volumetric water content and soil water matric potential sensors to facilitate the determination of field-obtained soil water characteristic curves (SWCCs) and hydraulic …

Dem Study Of A Single Stone Column In A Clayey Stratum, Anibal Enrique Santos

Graduate Theses and Dissertations

Aggregate piers are an alternative ground improvement technique used for improving the bearing capacity and reducing the total and differential settlement of foundations supported on compressible soils. The piers are composed of a series of vibrationally compacted aggregate lifts from a desired depth up to the finished foundation level. The shear strength of the coarse-grained material comprising an aggregate pier is defined by its internal friction angle. There are several factors affecting the friction angle of the granular material that include: confining stress, particle shape, relative density and particle distribution (gradation). These factors are not directly considered in the design …

Soil-Structure Interaction Effects On The Seismic Response Of Low-Rise Eccentrically Braced Frames, Luis Gerardo Buitrago Goyez

Graduate Theses and Dissertations

The importance of soil-structure interaction (SSI) effects on the seismic response of buildings has been long recognized and has been researched for over 40 years. However, SSI analysis has only been applied in a few building projects because the fixed base condition is considered to provide a conservative estimation for the response of buildings under seismic loads. This assumption of a fixed base condition adopted by practitioners is not always conservative or cost-effective, especially for rigid buildings over soft soils. Additionally, for the case of ductile steel frames with eccentric configurations, the influence of SSI on their seismic performance has …

Laboratory Resistivity Measurements For Soil Characterization, Behdad Mofarraj Kouchaki

Graduate Theses and Dissertations

Field based electrical resistivity measurements, such as electrical resistivity tomography (ERT) and capacitively coupled resistivity (CCR), are geophysical methods that offer a non-destructive and rapid means to collect continuous data. As such, ERT and CCR are becoming increasingly popular tools for geotechnical engineers; however, it is challenging to derive geotechnical information such as soil type, density, and water content from the data. A laboratory geophysical investigation was carried out to gain a better understanding of the parameters that affect the electrical resistivity of soils and devise a relationship between resistivity and soil type or classification. In this study, a soil …

Development Of Deep Site Specific And Reference Shear Wave Velocity Profiles In The Canterbury Plains, New Zealand, Michael Ryan Deschenes

Graduate Theses and Dissertations

Deep (typically >1000 m) shear wave velocity profiles were developed across the Canterbury basin at nine strong motion stations using a combination of active and passive surface wave methods and horizontal to vertical spectral ratio measurements. A multi-mode, multi-method joint inversion process, which included Rayleigh and Love wave dispersion and horizontal to vertical spectral ratio data, was used to estimate the shear wave velocity profiles at each site. A-priori geologic information was utilized in defining preliminary constraints on the complex geologic layering of the Canterbury basin. At sites where interbedded layers were present, velocity reversals were considered in the inversion. …

Geophysical Assessment Of Kinion Lake Dam, Tim Allen Moody

Graduate Theses and Dissertations

Geophysical methods including Capacitively-Coupled Resistivity (CCR), Electrical Resistivity Tomography/Imaging (ERT/ERI), Multichannel Analysis of Surface Waves (MASW) with Love and Rayleigh waves and a Full-Waveform Inversion (FWI) were performed on Kinion Lake Dam, an earth-filled embankment dam that has historically experienced significant seepage and internal erosion issues. Surveys were completed along the crest and downstream toe of the dam. Results from the surveys indicate that each method is capable of resolving the bedrock depth within 1-2 m of locations shown on previous drilling logs, though some discrepancies between the methods exist. A weathered bedrock layer is believed to have led to …

Feasibility Of Additive Manufactured Materials For Use In Geotechnical Laboratory Testing Applications, Matthew P. Watters

Graduate Theses and Dissertations

The factors affecting the positive volumetric strain, or dilatancy, typically observed in response to shearing of a dense granular material have long been investigated; however, there still lacks a direct relationship between particle shapes and the resulting dilatant response. The typical Mohr-Coulomb strength parameter associated with granular material is known as the effective friction angle (φ’). For a dense granular assemblage, the peak friction angle has been described as being comprised of a dilatant friction angle (φ’d) component and a critical state friction angle (φ’cv) component. While the topic of dilatancy and factors (both inherent and extrinsic) affecting its behavior …

Development Of A Multiband Remote Sensing System For Determination Of Unsaturated Soil Properties, Cyrus D. Garner

Graduate Theses and Dissertations

A multiband system including active microwave sensing and visible-near infrared reflectance spectroscopy was developed to measure unsaturated soil properties in both field and laboratory environments. Remote measurements of soil volumetric water content (θv), soil water matric potential (ψ), and soil index properties (liquid limit [LL], plastic limit [PL], and clay fraction [CF]) were conducted. Field-based measurement of θv was conducted using a ground-based radar system and field measurements within 10 percentage points of measurements acquired with traditional sampling techniques were obtained. Laboratory-based, visible and near infrared spectroscopy was found to be capable of obtaining empirical, soil specific regression functions (partial …

Induced Earthquakes And Public Safety, Lyndsey L. Dickson

Civil Engineering Undergraduate Honors Theses

Like the number of earthquakes felt in Oklahoma, the number of media reports regarding large-magnitude earthquakes in Oklahoma has increased in recent years. News headlines that mention property damage and question who is responsible have sparked heated debated. In this document, a discussion is presented over the responsibility of engineers for the public’s safety in relation to earthquakes. Input from various groups is discussed, the action taken in Oklahoma is outlined, and ethical obligations presented by the American Society of Civil Engineers are considered. The United States Geological Survey (USGS) has reported a major grievance against building-code committees, but many …

Effectiveness Of Small Strain Shear Wave Velocity As A Property For Assessing Damage Associated With Alkali-Silica Reaction In Concrete, Dillon K. Self

Civil Engineering Undergraduate Honors Theses

This research paper details the monitoring of expansion and shear wave velocity for fifteen concrete prisms cast in accordance with ASTM C1293 utilizing five mix designs with varying levels of ASR reactivity. Jobe sand and sodium hydroxide pellets were added in various quantities to increase the reactivity of the prisms. Strain measurements of the prisms were taken according to ASTM C129 and the shear wave velocity of the prisms was measured using ASTM C215. These measurements were taken weekly, then monthly for over a year. It was determined that shear wave velocity of the prisms decrease linearly as strain in …

Soil Moduli Obtained From A Back Pressure Constant Rate Of Strain Bender Element Consolidation Apparatus, Yi Zhao

Graduate Theses and Dissertations

A back-pressure saturated, constant-rate-of-strain consolidation device was modified to incorporate bender elements (BP-CRS-BE) and thus allowed for shear wave measurements during consolidation tests. This newly fabricated system has many advantages over other previous or current devices: 1) it can be utilized not only for laboratory prepared soil samples but also for field sampled soils such as Shelby tube samples, and 2) continuous compression curves, and continuous values of vertical hydraulic conductivity and coefficient of consolidation can be acquired with a significant reduction in testing time. Soil modulus values such as shear modulus and constrained modulus are also able to be …

Validation Of An Internal Camera Based Volume Determination System For Triaxial Testing, Leah D. Miramontes

Civil Engineering Undergraduate Honors Theses

Accurate strain and volume measurements are critical to phase relationships and strength determination for saturated and unsaturated soils. In recent years, laboratory-based photographic techniques of monitoring soil specimens have become more common. These techniques have been used to reconstruct 3D models and to determine strain and volumetric changes of triaxial specimens. A new technique that utilized digital photographs of the soil specimen, captured from within a triaxial testing cell, was utilized. Photographs were processed using photogrammetry software to reconstruct 3D models of the soil specimens. By placing camera equipment within the cell, the technique eliminated the need to account for …

Comparative Analysis Of Buckling-Restrained Braced Frames In Eccentric Configuration (Brbf-Es) And Eccentrically Braced Frames (Ebfs), Peter T. Vayda

Civil Engineering Undergraduate Honors Theses

Continuing on the findings of “Using Buckling-Restrained Braced Frames in Eccentric Configuration,” by Dr. Gary S. Prinz, P.E., which determined that, from a performance standpoint, BRBF-Es could be a viable alternative for EBFs. A comparative analysis was conducted on the design procedures and initial cost estimates of BRBF-Es and EBFs. Upon designing four 12-Story buildings (two BRBF-Es and two EBFs), it was determined that BRBF-Es were easier to design due to the statically determinant system. The initial costs estimates of BRBF-Es; however, ranged upwards of 30% more cost than EBFs. Therefore, the initial investment of more intensive structural engineering design …

Amount Of Uncertainty In The Methods Utilized To Design Drilled Shaft Foundations, Morgan Race

Graduate Theses and Dissertations

In 2001, load and resistance factor design (LRFD) for deep foundations was required by the American Association of State Highway and Transportation Officials (AASHTO). Following implementation of LRFD, localized calibration of resistance factors using data from the states of Colorado, Florida, Kansas, Louisiana/Mississippi, Missouri allowed these states to utilize higher resistance factors during design. However, characterizing the uncertainty in the design of DSF, regarding the geotechnical investigation methods and the utilized software programs, higher values of resistance factors may be calibrated to more efficiently design DSF with the same level of reliability.

Three test sites within the state of Arkansas, …

Alkali-Silica Reaction Mitigation Using High Volume Class C Fly Ash, Sydney Marie Dickson

Civil Engineering Undergraduate Honors Theses

Fly ash is the residue produced from coal combustion in electric generating plants. There are two types of fly ash, Class C and Class F. Approximately 40 percent of fly ash generated from coal combustion can be used as a partial replacement of cement in concrete. Incorporating fly ash improves concrete properties and extends its service life. Alkali-silica reaction (ASR) is an expansive reaction between reactive silica typically found in aggregates (rock and sand) and alkalis in cement. This reaction results in the formation of a gel that absorbs water and swells, which exerts an internal pressure in concrete. This …

A Study Of The Influence Of Particle Gradation In Bonded Assemblies, Matthew P. Watters

Civil Engineering Undergraduate Honors Theses

The discrete element method (DEM) has been used extensively to study soil, rock, and masonry behavior because of its ability to model the materials as individual particles or bonded clumps of particles. DEM allows for examination of the macro- and micro-scale response and provides a means to study the fundamental material behavior, but it is still considered computationally expensive in relation to other methods. To lower computational costs, the smallest particle sizes are often considered negligible and are left out of the model. Additionally, rock or intact materials are often modeled as a bonded assembly of uniform spheres. To date, …

Reliability-Based Design And Acceptance Protocol For Driven Piles, Joseph Jabo

Graduate Theses and Dissertations

The current use of the Arkansas Standard Specifications for Highway Construction Manuals (2003, 2014) for driven pile foundations faces various limitations which result in designs of questionable reliability. These specifications are based on the Allowable Stress Design method (ASD), cover a wide range of uncertainties, do not take into account pile and soil types, and were developed for general use. To overcome these challenges it is deemed necessary to develop a new design and acceptance protocol for driven piles. This new protocol incorporates locally calibrated RLFD resistance factors for accounting for local design and construction experiences and practices, as well …

Calibration Of Resistance Factors For Driven Piles Using Static And Dynamic Tests, Deshinka A. Bostwick

Graduate Theses and Dissertations

The field of geotechnical engineering has evolved from Allowable Stress Design (ASD) to Load Factor and Resistance Design (LRFD) which has led to a need to quantify the measures of uncertainty and the level of reliability associated with a project. The measures of uncertainty are quantified by load and resistance factors, while the level of reliability is driven by the amount of risk an owner is willing to take and is quantified by the reliability index. The load factors are defined through structural design codes, but the resistance factors have uncertainties that can be mitigated through reliability based design. The …

Field-Obtained Soil Water Characteristic Curves And Hydraulic Conductivity Functions, Elvis Ishimwe

Graduate Theses and Dissertations

A compacted clay liner (test pad) was constructed and instrumented with volumetric water content and soil matric potential sensors to determine soil water characteristic curves (SWCC) and hydraulic conductivity (k) functions. Specifically, the compacted clay liner was subjected to an infiltration cycle during a sealed double ring infiltrometer (SDRI) test followed by a drying cycle. After the drying cycle, Shelby tube samples were collected from the compacted clay liner and flexible wall permeability (FWP) tests were conducted on sub-samples to determine the saturated hydraulic conductivity. Moreover, two computer programs (RETC and UNSAT-H) were utilized to model the SWCCs and k-functions …

One-Dimensional Compressibility Of Intermediate Non-Plastic Soil Mixtures, Sean E. Salazar

Civil Engineering Undergraduate Honors Theses

The results of high stress, one-dimensional compression testing on intermediate soils are presented. Nevada Sand and silica silt mixtures were subjected to very high vertical stresses (140 MPa) in one-dimensional, monotonic compression. Each soil mixture was tested in a nominally loose condition. A specially designed mold with an integrated sensor array was fabricated to contain the soil during pre-consolidation and loading. The 1-D compression curve was plotted for each mixture in the double-logarithmic void ratio (e), and vertical effective stress (σ’v) space and characteristics of the Limiting Compression Curve (LCC) were identified. Initial and post test grain size distribution curves …

Analysis Of Aggregate Distribution In Self-Consolidating Concrete, Brendan Ho

Civil Engineering Undergraduate Honors Theses

Concrete consists of several key ingredients: cement, water, and coarse and fine aggregate. Depending on the proportions of these ingredients, the strength and workability of a concrete mix can be affected adversely. Segregation is the separation of aggregate and cement paste, resulting in a lack of homogeneity. Self-consolidating concrete (SCC) does not require traditional consolidation; however, it can be affected by segregation. This project examines different SCC mixtures and establishes ranges of values for slump flow, T20 , Visual Stability Index (VSI), J-ring flow and J-ring flow spread that ensures proper aggregate distribution and therefore reduces the potential of segregation. …

Slope Stability Monitoring Using Remote Sensing Techniques, Omar Alberto Conte Robles

Graduate Theses and Dissertations

During the past six years the Arkansas State Highway and Transportation Department (AHTD) has spent over nine million dollars repairing slope failures that have occurred in the state of Arkansas. Specifically, higher than average precipitation in 2004 and 2008 led to large quantities of slides, all of which were repaired. Two highways, within the state of Arkansas, with known historical movements along or across the highways are being monitored using traditional surveying techniques and advanced remote sensing techniques. These slides, both of which are located in fill slopes. One a 500-foot long slide located north of Chester, Arkansas, within the …

Efficacy Of Geosynthetic Separators And Filters: An Evaluation Of Test Sections In Marked Tree, Arkansas, Ashique Ali Boga

Graduate Theses and Dissertations

Field and laboratory tests were conducted on 18 full-scale, geosynthetic reinforced, roadway test sections located in Marked Tree, Arkansas. Base course, geosynthetic, and subgrade samples were collected, and pavement depth, in-situ density and in-situ hydraulic conductivity measurements were obtained during a geotechnical site investigation. The performance of sections containing geotextile products being used for separation and filtration (Carthage Mills FX-66, Mirafi 570, Propex 2006, Propex 2044, and Propex 4553) was investigated.

Moisture content, sieve analysis, Atterberg limits, modified proctor, specific gravity, and hydraulic conductivity tests were performed on the acquired soil samples. Transmissivity and permittivity testing was conducted on the …

The Marked Tree Site: Evaluation Of Geosynthetic Reinforcements In Flexible Pavements, Taylor Mitchell Goldman

Graduate Theses and Dissertations

This document presents findings from a three-year, full-scale, field research project aimed at determining the benefits of using geosynthetic reinforcements to improve the performance of flexible pavements constructed over poor subgrade soils. The test site, known as the Marked Tree site, is an 850-ft (258-m) long segment of low-volume frontage road along Highway 63 in the town of Marked Tree, Arkansas. The site, constructed in 2005, consists of seventeen 50-ft (15.2-m) long flexible pavement test sections with various types of geosynthetic reinforcements (woven and nonwoven geotextiles, and geogrids), which were all positioned at the base-subgrade interface, and two different nominal …

Hydraulic Conductivity Of Environmentally Controlled Landfill Liner Test Pad, Camila Maldonado Soria Galvarro

Civil Engineering Undergraduate Honors Theses

Laboratory and field hydraulic conductivity tests have been conducted on soil samples to develop and verify the zone of acceptance for liner placement. Compaction testing and flexible wall hydraulic conductivity tests were performed on fifteen (15) samples to determine the dry unit weight, molding water content, and laboratory permeability. Five of the fifteen samples were compacted at Standard proctor energy, five were compacted at 75 percent of Standard proctor energy, and five were compacted at 50 percent of Standard proctor energy. The results obtained from the laboratory portion of the testing program (the zone of acceptance) are presented. A ten …