Geotechnical Engineering Commons^™

2-D Non-Linear Finite Element Analysis Of Folsom Dam: Seismically Induced Separation And Pore Pressure Along The Soil-Concrete Interface, Grace Amoussou

Master of Science in Civil Engineering Theses

The seismic soil-concrete interface stability of composite dams has been an area of interest to many researchers. However, the true interface behavior during a seismic event has not been well understood. During a ground shaking, bonding and de-bonding action along the interface may cause significant separation of soil and concrete surfaces, and such a separation may take place at any depth along the interface creating a stability concern for the overall dam. Moreover, the repetitive nature of bonding/debonding behavior may induce excess pore pressure along the interface, which in turn, may trigger a liquefaction failure or a hydraulic fracture in …

Preliminary Investigation Of Required Bsca Amount For Soil Cement Mixtures, Mariel Mayori Rivero

Civil Engineering Undergraduate Honors Theses

The recent increase of flooding in the United States and the high expenses related to the damage that these floods have caused to waterway structures suggests a potential interest in rapid setting soil cement to make effective repairs. For this thesis, mix designs of soil only at three different sand-clay proportions were prepared and tested for moisture content and maximum dry density. Due to the early closing of the laboratory and research activities, reliable results were collected from the 70% sand and 30% clay proportions. At those proportions of soil, the optimum moisture content was found to be 8.88% with …

Structural Design Of Pool House In The City Of Columbia, Nathan F. Gates

Senior Theses

This report presents a structural design for a one-story pool house in the City of Columbia. The most important part of the project was determining critical horizontal and vertical loads, and designing each member in accordance to those governing loads. The loads we analyzed were dynamic, dead, live and seismic. By means of the LRFD method, the greatest possible load combination was calculated, combining the previously mentioned loads. These load combinations were different for each analysis, as the loading pressures will change depending on what structural system is being analyzed. This comprises the large part of the report and of …

Civil Engineering Research In Ireland 2020: Conference Proceedings, Kieran Ruane, Vesna Jaksic, Bidisha Ghosh, Magdalena Hajdukiewicz, Ciaran Hanley, Niall Holmes, Jennifer Keenahan, Zili Li, Patrick Mcgetrick, Ted Mckenna, Mary Moloney, Vikram Pakrashi, Niamh Power

Publications

Civil Engineering Research in Ireland 2020: Conference Proceedings.

Compressibility Of Fine-Grained Soil In Central Florida, Andre Kruk

Electronic Theses and Dissertations, 2020-2023

Fine-grained soils are responsible for most site settlements through a time dependent process known as consolidation. The magnitude of consolidation is quantified with three terms: the recompression and compression indices, referred to as the soil's compressibility indices, and preconsolidation pressure. The ideal methods to estimate these parameters are direct measurements from lab or in-situ field tests, other method include estimation from experience or from correlations to soil parameters. This study refines correlations between compressibility indices and index properties as previously researchers and soil mechanics suggest a strong correlation exists. This study also suggests a correlation to CPT parameters as this …

Decision-Making In Reuse Of Highway Bridge Foundations, Ehssan Hoomaan

Dissertations and Theses

According to the 2019 National Bridge Inventory data from Federal Highway Administration, the average age of highway bridges in the U.S.A. is 45 years, with almost 43% of existing highway bridges being older than 50 years, and eight percent of all U.S. national highway bridges being in poor condition. Foundation and substructure of existing highway bridges (over land and water) may have significant functional values even after being under service for decades. Reusing an existing bridge foundation during the reconstruction of a bridge (e.g., major rehabilitation, retrofitting, replacement of superstructure and substructure, and addition/removal of a span) has the potential …

Internet Of Things For Sustainable Mining, Abdul Salam

Faculty Publications

The sustainable mining Internet of Things deals with the applications of IoT technology to the coupled needs of sustainable recovery of metals and a healthy environment for a thriving planet. In this chapter, the IoT architecture and technology is presented to support development of a digital mining platform emphasizing the exploration of rock–fluid–environment interactions to develop extraction methods with maximum economic benefit, while maintaining and preserving both water quantity and quality, soil, and, ultimately, human health. New perspectives are provided for IoT applications in developing new mineral resources, improved management of tailings, monitoring and mitigating contamination from mining. Moreover, tools …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Incorporating Geophysical Data In Slope Stability Modeling For Two Slopes In Arkansas, Vanessa Lebow

Graduate Theses and Dissertations

Slope failures in the United States alone cause millions of dollars in damage to infrastructure, threaten national monuments, create environmental hazards, and take an average of 25-50 lives a year. With the inevitable construction that occurs on slopes, it is imperative that the slopes be properly designed which requires a thorough understanding of slope grade, subsurface soil conditions, soil strength parameters, water table locations, and depth to bedrock across the entire site. The preferred method of data collection would be to use borings and other in-situ methods; however, sometimes due to cost constraints or site accessibility only a very limited …

Rehabilitation Of Low Rise Rcc Structure Along 9m High Retaining Wall, Aniruddha Nakhawa Er, Vivek Deshmukh Dr

International Conference on Durability of Concrete Structures

Mumbai is the financial, commercial and entertainment capital of India, facing bigger challenges in accommodating its over growing population day by day. The Mumbai City has population of 18.4 million over its 634 km2 area, ie. Almost 350 ft2/person. This enormous rise in population density has restricted the development to expand vertically. This also, results in growth of major slums, which is almost 62% of the population dwelling in slums. Subsequently, the authorities is in need of a large scaled Slum Sanitation Program, which utilize the scarcely available land for construction of Community Toilet Blocks with involvement of NGO’s and …

Performance Of Drilled Shaft Under Combination Of Complicated Loads Under Hurricane Event, Jie Huang, Sazzad Bin-Shafique

Publications

This project includes experimental and numerical studies to investigate and assess the impact of vertical loads on a laterally loaded drilled shaft under various conditions. The experimental study includes lab testing and lab-scale load test to examine a drilled shaft subjected to vertical and lateral loads at a reduced scale. With the data obtained from the lab-scale testing, a numerical model was calibrated, which was used to perform a parametric study to scrutinize the effect of many possible factors such as soil stiffness, soil friction angle, and drilled shaft geometry. With all the factors considered in this study, the vertical …

Point Cloud Technology For Analysis Of Existing Structures, Jacob Cano

Electronic Theses and Dissertations

For this thesis, a study was completed on two different structures on the UCF Orlando campus through the use of both structural plans and point cloud technology. The results sought to understand the viability of point cloud technology as an accurate tool for the static and dynamic modal analysis of existing structures. For static analysis, a portion of the framing of Spectrum Stadium was rendered, modeled, analyzed and compared to a previous case study. The results emphasized how different users can render dissimilar member sizes and lengths due to human judgment on point cloud visuals. The study also found that …

Tension Splitting Strength Of Bcsa Concrete Cylinders, Andrew Steven Deschenes

Civil Engineering Undergraduate Honors Theses

The focus of this research was to compare the tension splitting strength (TSS) of belitic calcium sufloaluminate (BCSA) cement concrete to tensile strength predicted by the American Concrete Institute (ACI) and to similarly proportioned portland cement (PC) concrete. BCSA is a rapid-setting cement with higher early strength, higher ettringite content, and lower calcium silicate hydrate (C-S-H) content than PC. PC and BCSA cement concrete cylinders were broken at different ages in both uniaxial compression and TSS. It was found that BCSA had a similar TSS to both the ACI prediction and PC TSS, but the results require further testing for …

Urban Underground Infrastructure Monitoring Iot: The Path Loss Analysis, Abdul Salam, Syed Shah

Faculty Publications

The extra quantities of wastewater entering the pipes can cause backups that result in sanitary sewer overflows. Urban underground infrastructure monitoring is important for controlling the flow of extraneous water into the pipelines. By combining the wireless underground communications and sensor solutions, the urban underground IoT applications such as real time wastewater and storm water overflow monitoring can be developed. In this paper, the path loss analysis of wireless underground communications in urban underground IoT for wastewater monitoring has been presented. It has been shown that the communication range of up to 4 kilometers can be achieved from an underground …

Unl-Cc Outdoor Education Center Master Plan, Marie Wagner

Honors Program: Senior Projects (Public)

The following report contains the work done by the group Griswold Engineering in completion of the Senior Design requirements for Civil Engineering and the Honors Requirements of the Project Manager. As the project manager, my job was to organize the project as a whole and to work alongside the Structural Engineer on the project. One of the main problems to overcome was the division of labor amongst the group. The project was originally conceived as a group project with one project manager and five other students to serve as the project engineers in each subdiscipline. Since this group only had …

Behavior Of Geothermal Energy Piles Embedded In Rock, Ehab Sabi

Civil and Environmental Engineering Theses and Dissertations

Geothermal energy piles are categorized as closed systems. Energy piles are a relatively new technology which couples the structural role of traditional pile foundations to that of heat exchangers to fulfill the required energy demand of buildings and infrastructures. These foundations are equipped with pipes embedded in the concrete forming the pile. While connected to a heat pump, the fluid circulating inside these pipes provides the exchange of heat with the ground for heating and cooling purposes. As the undisturbed temperature at the shallower depths of the ground stays comparatively constant the whole year, being warmer than the surrounding temperature …

Civil Engineering Design Of Cornhusker Council's Outdoor Education Center, Kelly Weiler

Honors Program: Senior Projects (Public)

A team of geotechnical, structural, hydraulic, environmental, and transportation experts collaborated to provide engineering solutions to the Cornhusker Council in an effort to solve the current problems facing their Outdoor Education Center. This results of this project provided the structural design of three bridges on the property, transportation plans for two parking lots and roadway design, geotechnical recommendations for soil testing and erosion prevention, and an environmental and hydraulic analysis of the property. A major challenge in the design of this project is the consideration of the dangers and regulations that accompany the floodway and floodplain regions on site. Various …

Finite Element Modeling Of Mechanically Stabilized Earth Walls Built With Welded Wire Wall Panels, Dejuan G. Solan

College of Graduate Studies: Theses & Dissertations

In this thesis, a finite element modeling of Mechanically Stabilized Earth (MSE) walls using welded wire wall panels was performed. The implementation of finite element modeling and analysis proved to be quite efficient in simulating the three-dimensional behavior of wall panels that are a part of MSE walls. The comprehensive finite element model included defined concrete and steel material properties in order to present both the realistic behaviors of each component in the model as well as better facilitating and increasing the accuracy of the simulation of numerous finite element analysis (FEA) cases. FEA was employed to simulate welded wire …

Young’S Modulus As A Measurement To Estimate Damage Related With Alkali-Silica Reaction In Concrete., Anazaria J. Ortega Gonzalez

Civil Engineering Undergraduate Honors Theses

The main purpose of this research is to compare two nondestructive methods to assess Alkali-Silica reaction (ASR) in concrete. Fifteen concrete prisms were cast using aggregates with different Alkali-Silica reactivity such as Jobe sand and Van Buren sand. The change in strain, shear wave velocity and Young’s modulus were determined according to ASTM C129 and ASTM C215, respectively. This data was collected by Dillon K Self, who determined that the shear wave velocity and strain are inversely proportional. However, when single cracking in the concrete specimen transition to map cracking, the shear wave velocity dropped significantly, whereas the strain value …

Utilizing The Hvsr Second Peak For Surface Wave Inversions In The Mississippi Embayment, Ashraf Kamal Himel

Graduate Theses and Dissertations

Ambient noise data from 24 sites within the Mississippi Embayment were analyzed to estimate the fundamental frequency using the horizontal to vertical spectral ratio (HVSR) method. The fundamental frequency ranged from 0.17 to 3.43 Hz for the tested sites. At seventeen of the sites, a second higher frequency HVSR peak, which ranged from 0.617 Hz to 2.154 Hz, was observed in addition to the fundamental HVSR peak. The second peak frequency in the HVSR curve has been attributed by previous researchers as either an odd harmonic of the fundamental peak or a shallow impedance contrast from the Memphis sand layer …

My Catalyst, Gabrielle Gambino Lyon

Celebration of Learning

Over the course of my internship and shadow program with Pepper Lawson Construction and Ziegler Cooper Architects, I was able to explore the various career paths involved in the design, construction, and civil engineering fields. My work on the construction site of a high-rise apartment building located in the heart of Houston, TX allowed me first-hand experience working and learning alongside project engineers, contractors, building developers, and the construction team.

This project was the perfect confluence of my main areas of interest: structural, mechanical, civil, and environmental engineering, as well as architecture. My daily work consisted of on-site walk throughs, …

Liquefaction-Induced Dragload And/Or Downdrag On Deep Foundations Within The New Madrid Seismic Zone, Ishimwe Elvis

Graduate Theses and Dissertations

Deep foundation elements are typically used to transfer structural loads for multi-story buildings and large-span bridges to a competent soil layer when 1) the soil close to the ground surface has no sufficient bearing capacity, and when 2) liquefiable soils are encountered. The majority of the bridges constructed within seismic zones rely upon the stability of earthen embankments and deep foundation that are installed above or within liquefiable soil deposits. Despite large factor of safety values or different load and resistance factors being used to adequately design deep foundations within seismic areas, soil liquefaction may cause extensive damage to the …

Introduction To Infrastructure - The Influence Of Natural Disasters On Infrastructure, Tri Tam Nguyen, Sean M. Raday, Daniel Leverick

STEM Student Research Symposium Posters

In this paper, three major hurricanes in 2017 were examined to determine the damage these hurricanes have done to the infrastructure. Infrastructure has an important role in the nation’s sustained economic development. Infrastructure consists of two main types which are “hard” infrastructure and “soft” infrastructure. Hard infrastructure is the physical networks which include transportation, power, etc. while soft infrastructure is institutions and human capital. Inadequate and inefficient performance of “hard” or “soft” infrastructure would prevent economy from achieving full growth. In the past decades, a significant increase in the number of natural disasters has had great impact on infrastructure systems. …

Tire-Derived Geo-Cylinders And Polymer Products For Enhancing The Properties Of Base/Sub Base Materials In Pavement Systems, Justin Scott Smith

Graduate Theses, Dissertations, and Problem Reports (ETD)

As a critical part of the transportation network, pavements offer a safe means for vehicular traffic. Pavements are subjected to many forms of stress during their service life, and they are susceptible to environment related cracking and failures. Failures can be attributed to poor subgrade, freeze-thaw variations, and fatigue under repetitive axle loadings. Reinforcement products such as tire-derived geo-cylinders (TDGC) which make-up mechanical concrete and geo-polymers have been utilized in civil engineering practice, and this research aims to understand the potential life of tested pavement system components set at displacement limitations when reinforced with TDGCs and geo-polymers from exposure to …

Characterization And Modeling Of Asphalt Concrete For Dynamic Properties And Performances, A S M A. Rahman

Civil Engineering ETDs

The recently developed mechanistic-empirical pavement design guide (MEPDG, also known as Pavement M-E design method) uses the nationally calibrated, binder viscosity-based dynamic modulus predictive model for the design and analysis of asphalt pavements. In this study, this model is assessed for its appropriateness for asphalt-aggregate mixtures typically used in New Mexico. In essence, this study investigates the predictability issue of complex modulus of New Mexico mixes. A total of 54 Superpave mixes with different aggregate gradations, air voids, and binder grades were collected from the mixing plants and from the pavement construction sites. The loose asphalt mixtures were then compacted, …

Numerical Evaluation Of The Lateral Behavior Of Vertical And Battered Pile Group Foundations Using 3-D Finite Element Modeling, Ahmad Souri

LSU Doctoral Dissertations

The design of pile foundations to resist lateral loads is essential in offshore structures and bridge foundations. The lateral behavior of piles has been studied in the past by experimental investigations coupled with analytical and numerical methods. The problem is complex due to the nonlinearities from soil behavior, gap formation, and pile-soil-pile interaction in pile groups (or the group effect). In this work, the finite element (FE) modeling was used to study the lateral behavior of pile groups. The FE method is robust and allows incorporating the necessary aspects for studying the behavior of pile groups. The nonlinear material behavior …

Soil-Structure Interaction Effects On The Seismic Response Of Low-Rise Eccentrically Braced Frames, Luis Gerardo Buitrago Goyez

Graduate Theses and Dissertations

The importance of soil-structure interaction (SSI) effects on the seismic response of buildings has been long recognized and has been researched for over 40 years. However, SSI analysis has only been applied in a few building projects because the fixed base condition is considered to provide a conservative estimation for the response of buildings under seismic loads. This assumption of a fixed base condition adopted by practitioners is not always conservative or cost-effective, especially for rigid buildings over soft soils. Additionally, for the case of ductile steel frames with eccentric configurations, the influence of SSI on their seismic performance has …

Characterization Of Unknown Bridge Foundations, Saman Rashidyan

Civil Engineering ETDs

The National Bridge Inventory (NBI) recognized 86,133 bridges in the United States have no foundation data on record in 2003. It is evident that an unknown percentage of the 86,133 bridges identified by NBI with missing foundation data could also be highly vulnerable to scouring induced by water flow coupled with erodible soils. Conventional excavation, coring and boring excavations to identify unknown bridge foundation depths and types are deemed to be expensive, destructive, and limited in their application to the unknown foundation problem. Many surface and borehole nondestructive testing (NDT) technologies have been developed for this purpose. Three economical proven …

Induced Earthquakes And Public Safety, Lyndsey L. Dickson

Civil Engineering Undergraduate Honors Theses

Like the number of earthquakes felt in Oklahoma, the number of media reports regarding large-magnitude earthquakes in Oklahoma has increased in recent years. News headlines that mention property damage and question who is responsible have sparked heated debated. In this document, a discussion is presented over the responsibility of engineers for the public’s safety in relation to earthquakes. Input from various groups is discussed, the action taken in Oklahoma is outlined, and ethical obligations presented by the American Society of Civil Engineers are considered. The United States Geological Survey (USGS) has reported a major grievance against building-code committees, but many …

Effectiveness Of Small Strain Shear Wave Velocity As A Property For Assessing Damage Associated With Alkali-Silica Reaction In Concrete, Dillon K. Self

Civil Engineering Undergraduate Honors Theses

This research paper details the monitoring of expansion and shear wave velocity for fifteen concrete prisms cast in accordance with ASTM C1293 utilizing five mix designs with varying levels of ASR reactivity. Jobe sand and sodium hydroxide pellets were added in various quantities to increase the reactivity of the prisms. Strain measurements of the prisms were taken according to ASTM C129 and the shear wave velocity of the prisms was measured using ASTM C215. These measurements were taken weekly, then monthly for over a year. It was determined that shear wave velocity of the prisms decrease linearly as strain in …