Geotechnical Engineering Commons^™

Indot Qc/Qa Earthwork And Intelligent Compaction Us 31/Us 35 At Kokomo, Kurt Sommer

Purdue Road School

This presentation discusses a 2012 case study using QC/QA Earthwork Specifications and Intelligent Compaction Rollers for soils.

INDOT Contract IR-30111 in Greenfield District on US 31/ US 35 at Kokomo used this process in 2012 and continuing into 2013 for the control and acceptance of approximately 1 million cubic yards of earthwork.

Slope Stability Monitoring Using Remote Sensing Techniques, Omar Alberto Conte Robles

Graduate Theses and Dissertations

During the past six years the Arkansas State Highway and Transportation Department (AHTD) has spent over nine million dollars repairing slope failures that have occurred in the state of Arkansas. Specifically, higher than average precipitation in 2004 and 2008 led to large quantities of slides, all of which were repaired. Two highways, within the state of Arkansas, with known historical movements along or across the highways are being monitored using traditional surveying techniques and advanced remote sensing techniques. These slides, both of which are located in fill slopes. One a 500-foot long slide located north of Chester, Arkansas, within the …

Dimensional Stability Of Geosynthetic Clay Liners In Landfill Applications, Gregory R. Olsen

Master's Theses

An investigation was conducted related to the dimensional stability of geosynthetic clay liners (GCLs) in landfill applications. Multiple occurrences of panel separation of overlap seams in GCLs have been documented; however, explanation for the relative contribution of various mechanisms causing shrinkage has been limited. A systematic test program was conducted to determine the effects of a variety of conditions on GCL dimensional stability.

Effects of initial moisture content, permeant type, and overburden pressure were tested by subjecting various GCL products to wet-dry cycles and measuring the dimensional change with each cycle. Different GCL types were each tested under various combinations …

Seamless Bridge And Roadway System For The U.S. Practice, Nima Ala

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Expansion joints are one of the main causes for high maintenance costs in bridges. The search for ideal expansion joints has proven fruitless. That is why it has been said that “the best joint is no joint”. A seamless bridge system is envisioned that results in bridges with long service lives by eliminating the joints over the entire length of the bridge, approach slab and a segment of the roadway called transition. All bridge thermal movements are dissipated to zero in the transition. The system is similar to a system developed in Australia but modifications had to be made to …

Effects Of Warm-Mix Asphalt Additives On Asphalt Mixture Characteristics And Pavement Performance, Jun Zhang

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The primary objective of this research is to evaluate the feasibility of several WMA mixtures as potential asphalt paving mixtures for Nebraska pavements. To that end, three well-known WMA additives (i.e., Sasobit, Evotherm, and Advera synthetic zeolite) were evaluated. For a more realistic evaluation of the WMA approaches, trial pavement sections of the WMA mixtures and their HMA counterparts were implemented in Antelope County, Nebraska. More than one ton of field-mixed loose mixtures were collected at the time of paving and were transported to the NDOR and UNL laboratories to conduct comprehensive laboratory evaluations and pavement performance predictions of the …

A Life Cycle Cost Analysis Of Large-Scale Thermal Energy Storage Technologies For Buildings Using Combined Heat And Power, Kenneth Gaine, Aidan Duffy

Conference Papers

Buildings account for approximately 40% of energy consumption and greenhouse gas (GHG) emissions in developed economies, of which approximately 55% of building energy is used for heating and cooling. The reduction of building-related GHG emissions is a high international policy priority. For this reason and because there are many technical solutions for this, these polices should involve significant improvements in the uptake of small-scale energy efficient (EE) systems. However the widespread deployment of many technologies, must overcome a number of barriers, one of which is a temporal (diurnal or seasonal) mismatch between supply and demand. Costeffective thermal storage solutions have …

Influence Of Material Type, Aggregate Size, And Unconfined Compressive Strength On Water Jetting Of Cidh Pile Anomalies, Joseph Carl Heavin

Master's Theses

Water jetting as a means for removing anomalous materials from cast-in-drilled-hole (CIDH) piles was examined. The primary objective of this research was to establish empirical relationships between different jetting parameters and the removal of commonly occurring anomalous zone materials, including low-strength concrete, slurry mixed concrete, grout, and clay soil. Also investigated was the current standard-of-practice used by water jetting contractors within California. The testing specimens consisted of typical anomalous material with unconfined compressive strengths between 5 and 6,000 psi. The experimental work consisted of water blasting submerged specimens using rotary jets, nozzles, and pumping equipment typically used in construction practice. …

Performance Of A Stormwater Filter And Bacteria Inactivation Using Biocidal Media, Alexander Scott Bowerman

Master's Theses

There are many possible ways to mitigate stormwater pollution, but this study focused on the DrainPacTM catchment basin insert and the feasibility of integrating N-halamine biocidal brominated beads into the filter system. This study was divided into three sections. The first section involved testing a DrainPacTM filter for treatable flow rates, head loss, and removal of solids, oil, and bacteria. The DrainPacTM filter is designed to be installed in a stormwater catch basin. The filter is composed of a 12 x 41 inch metal frame with textile filter media attached to it in a basket shape. The upper portion of …

Site Response Zones And Short-Period Earthquake Ground Motion Projections For The Las Vegas Basin, Barbara Luke, Ying Liu

Civil and Environmental Engineering and Construction Faculty Research

A deterministic seismic hazard analysis was conducted to address the effect of local soil conditions on earthquake-induced strong ground motion in the Las Vegas Basin, Nevada (US). Using a large geological and geotechnical database, two response units were defined: a fine-grained unit, predominantly clay; and a coarse-grained unit, predominantly gravel. A moderate number of high-quality shallow shear wave velocity measurements were collected from which characteristic shear wave velocity profiles were developed for each response unit. An equivalent-linear one-dimensional site response model was used. The model was calibrated using a basin-wide, small-strain ground motion database. Calibration tests showed that ground motion …

Detecting Anomalous Inclusions In Soil Profiles: Encouraging The Use Of Geophysics To Solve Engineering Problems, Barbara Luke, Carlos Calderon-Macias

Civil and Environmental Engineering and Construction Faculty Research

Geotechnical site investigations often do not take full advantage of geophysical methods. As examples, when delineating cemented strata and when detecting shallow cavities, investigations can be enhanced greatly for low additional cost by incorporating seismic surface-based measurements.

Understanding Manufacturing Energy Use Through Statistical Analysis, J. Kelly Kissock, John Seryak

Mechanical and Aerospace Engineering Faculty Publications

Energy in manufacturing facilities is used for direct production of goods, space conditioning, and general facility support such as lighting. This paper presents a methodology for statistically analyzing plant energy use in terms of these major end uses. The methodology uses as few as 60 data points that are relatively easy for most plants to obtain. Multivariable change-point models of electricity and natural gas use as functions of outdoor air temperature and production data are then developed. The statistical models can be used to predict energy use for energy budgeting, measure savings, determine cost structures, and diagnostic purposes. Moreover, in …

Scientific And Engineering Studies Of Systems, Structures, And Components Important To Safety For A Potential Repository At Yucca Mountain, Nevada, Ian Buckle, E. Manos Maragakis

Publications (YM)

TASK 26: Upgrade of Earthquake Simulation Facilities in the Large-Scale Structures Laboratory at University of Nevada Reno The objective of this Task was to purchase, install and commission the equipment necessary to upgrade two existing shake tables in the Structures Laboratory at UNR, from uniaxial to biaxial motion. It was recognized that a parallel effort, funded by NSF and HUD, to add a third biaxial table with identical properties to the upgraded existing tables, would be undertaken at the same time.

Performance Comparison Of A Roundabout Versus Two-Way Stop Controlled (Twsc) Intersections, Deogratias Eustace

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

The superior safety record of modern roundabouts is well known in Western Europe, Australia and in most British-influenced countries around the world. The experience from a single modern roundabout installed in the City of Manhattan, Kansas, some three years ago, also shares the same experience. A major study of the performance of Manhattan, Kansas, modern roundabout was conducted at Kansas State University (KSU) and was co-sponsored by Mac-Blackwell National Rural Transportation Study Center, Kansas State University, and the City of Manhattan. The study examined three intersections, one modern roundabout and two Two-Way Stop Controlled (TWSC) intersections with similar traffic conditions. …

A Plane Coordinate System For Bernalillo County, Karl V. Morin

Civil Engineering ETDs

The first purpose of this thesis is to frame an enabling act that could be submitted to legislature for adoption. Such an act would authorize the use of plane coordinate system, but not make it mandatory. Twenty-four states have passed laws establishing state coordinate systems.

A second purpose of this thesis is to provide practicing engineers with all the necessary information and explanatory material in one manuscript to permit them to apply the system to their work. An example is worked out in detail using local points known to local men and fully explained step by step.

In addition to …