Geotechnical Engineering Commons^™

Karst Sinkhole Detecting And Mapping Using Airborne Lidar, Su Zhang, Shirley Baros, Susan Bogus

Data

Corresponding data set for Tran-SET Project No. 18GTUNM01. Abstract of the final report is stated below for reference:

"The focus of this study is to detect sinkhole hazards using airborne light detection and ranging (LiDAR) data. The premise is sinkholes, particularly those close to transportation infrastructure assets, could cause substantial damages to infrastructure assets, and therefore, being able to accurately and rapidly detect them is essential. However, it is expensive, time-consuming, labor-intensive, and unsafe to survey sinkholes using conventional ground observation methods. This research project was focused on developing accurate and rapid airborne LiDAR-based sinkhole detection and mapping methods, and …

Development Of Metals Corrosion Maps Of Arkansas And Maintenance Of Cross-Drains, Zahid Hossain, Ashraf Elsayed, Mdariful Hasan

Data

Corresponding data set for Tran-SET Project No. 18GTASU01. Abstract of the final report is stated below for reference:

"Corrosion potential of metallic structures in alluvial soils is governed by chemical and electromagnetic properties of the soils. Geotechnical engineers are generally more concerned about different types of soils and their physical and mechanical properties than the chemical aspects. The main objective of this study is to analyze the geotechnical, electrochemical and electromagnetic properties of soils in Arkansas. Important parameters (e.g., soil resistivity) related to corrosion potential of metal culverts have been predicted through neural network (NN) models. The developed NN models …

Karst Sinkhole Detecting And Mapping Using Airborne Lidar, Su Zhang, Shirley Baros, Susan Bogus

Publications

The focus of this study is to detect sinkhole hazards using airborne light detection and ranging (LiDAR) data. The premise is sinkholes, particularly those close to transportation infrastructure assets, could cause substantial damages to infrastructure assets, and therefore, being able to accurately and rapidly detect them is essential. However, it is expensive, time-consuming, labor-intensive, and unsafe to survey sinkholes using conventional ground observation methods. This research project was focused on developing accurate and rapid airborne LiDAR-based sinkhole detection and mapping methods, and transfer the technologies to transportation engineers for implementation and workforce development. The project team also identified best practices …

Development Of Metals Corrosion Maps Of Arkansas And Maintenance Of Cross-Drains, Zahid Hossain, Ashraf Elsayed, Mdariful Hasan

Publications

Corrosion potential of metallic structures in alluvial soils is governed by chemical and electromagnetic properties of the soils. Geotechnical engineers are generally more concerned about different types of soils and their physical and mechanical properties than the chemical aspects. The main objective of this study is to analyze the geotechnical, electrochemical and electromagnetic properties of soils in Arkansas. Important parameters (e.g., soil resistivity) related to corrosion potential of metal culverts have been predicted through neural network (NN) models. The developed NN models have been trained and verified by using laboratory test results of soil samples collected from Arkansas Department of …

Developing Implementable Climatic Input Data And Moisture Boundary Conditions For Pavement Analysis And Design, Rifat Bulut, Amir Hossein Javid

Publications

The main objective of this study is to develop a practical and implementable numerical model for predicting the moisture (suction) regime within the pavement subgrade system. The research quality and uniformly-dispersed climate data over short distances from Oklahoma Mesonet and the Mitchell based moisture (suction) prediction methods establish the main background of the research study. The study involved numerical modeling and statistical analysis of climatic weather data. The proposed moisture variation model predicts the suction distribution throughout the soil subgrade by solving the diffusion equation and incorporates the measured suction from the Oklahoma Mesonet to estimate the diffusion coefficient. The …

Data Sheet For Cone Penetration Test In Soil-Bentonite Cutoff Wall, Jeffrey C. Evans

NSF Soil-Bentonite Slurry Trench Cutoff Wall Datasets

This data sheet shows the measurements taken using a cone penetration test in a soil-bentonite slurry trench cutoff wall. The testing was done following ASTM D 3441.

Field Performance And Cost Effectiveness Of Crack Sealing In Flexible And Composite Pavements, Momen Ragab Mousa

LSU Doctoral Dissertations

Surface cracking is one of the major surface distresses in asphalt concrete (AC) pavement, allowing water infiltration through the cracks, causing stripping in asphalt pavement layers, and weakening and deteriorating the base and/or subgrade. Its treatment, therefore, is one of the major activities in pavement preservation for many state DOTs. Among the various treatment methods currently available to preserve AC pavement with existing surface cracking are various forms of crack sealing. Crack sealing is not a common practice to Louisiana highways since the benefit of such treatment appears to be affected by the elevation of the ground water table. Studies …

Case Study: Using Geofoam On A School Project In Encinitas, Ca, Matthew D. Gaebe

Construction Management

This paper is a case study that identifies why Geofoam was used as in-fill material for a construction project located at a high school in Encinitas, CA. The Geofoam was installed under a stairway that connects to a structural retaining wall. The concrete formwork was connected directly to the foam and the stairs were poured in place onsite. The foam acted as the on-grade material, so the concrete stairs did not have to be self-supporting. The purpose of this study is to understand the benefits of using Geofoam, as the in-fill material, as opposed to other traditional materials. An analysis …

Point Cloud Technology For Analysis Of Existing Structures, Jacob Cano

Electronic Theses and Dissertations

For this thesis, a study was completed on two different structures on the UCF Orlando campus through the use of both structural plans and point cloud technology. The results sought to understand the viability of point cloud technology as an accurate tool for the static and dynamic modal analysis of existing structures. For static analysis, a portion of the framing of Spectrum Stadium was rendered, modeled, analyzed and compared to a previous case study. The results emphasized how different users can render dissimilar member sizes and lengths due to human judgment on point cloud visuals. The study also found that …

Tension Splitting Strength Of Bcsa Concrete Cylinders, Andrew Steven Deschenes

Civil Engineering Undergraduate Honors Theses

The focus of this research was to compare the tension splitting strength (TSS) of belitic calcium sufloaluminate (BCSA) cement concrete to tensile strength predicted by the American Concrete Institute (ACI) and to similarly proportioned portland cement (PC) concrete. BCSA is a rapid-setting cement with higher early strength, higher ettringite content, and lower calcium silicate hydrate (C-S-H) content than PC. PC and BCSA cement concrete cylinders were broken at different ages in both uniaxial compression and TSS. It was found that BCSA had a similar TSS to both the ACI prediction and PC TSS, but the results require further testing for …

A Unified Risk-Based Framework For Assessing Sustainability And Resiliency Of Civil Infrastructure, Thomas Adam Robbins

Boise State University Theses and Dissertations

As of February 2019, the National Aeronautics and Space Administration (NASA) has reported since 1880 the average global temperature has increased 1°C, with the warmest year on record being 2016. As the years continue to pass, it is becoming more evident that climate change is occurring, which is known to be a catalyst for climatic weather events. Statistically speaking, these events are more prevalent, and catastrophic exemplified as hurricanes, earthquakes, flooding, and fires. In addition to the increase of potentially catastrophic events, society as a whole has become more conscientious in the use and preservation of natural resources, waste generation, …

Urban Underground Infrastructure Monitoring Iot: The Path Loss Analysis, Abdul Salam, Syed Shah

Faculty Publications

The extra quantities of wastewater entering the pipes can cause backups that result in sanitary sewer overflows. Urban underground infrastructure monitoring is important for controlling the flow of extraneous water into the pipelines. By combining the wireless underground communications and sensor solutions, the urban underground IoT applications such as real time wastewater and storm water overflow monitoring can be developed. In this paper, the path loss analysis of wireless underground communications in urban underground IoT for wastewater monitoring has been presented. It has been shown that the communication range of up to 4 kilometers can be achieved from an underground …

Unl-Cc Outdoor Education Center Master Plan, Marie Wagner

Honors Program: Senior Projects (Public)

The following report contains the work done by the group Griswold Engineering in completion of the Senior Design requirements for Civil Engineering and the Honors Requirements of the Project Manager. As the project manager, my job was to organize the project as a whole and to work alongside the Structural Engineer on the project. One of the main problems to overcome was the division of labor amongst the group. The project was originally conceived as a group project with one project manager and five other students to serve as the project engineers in each subdiscipline. Since this group only had …

Seismic Performance Of Earth Slopes Subjected To Earthquake Mainshock – Aftershock Sequences, Alisha Khanal

Civil Engineering Theses

Mainshocks are usually followed by aftershocks. Aftershocks continue over a period of time with a decreasing frequency and there is not sufficient time for repair and retrofit between a mainshock – aftershock sequence. Typically, aftershocks are smaller in magnitude; however, aftershock ground motion characteristics such as the intensity and duration can be greater than the mainshock due to the changes in the earthquake mechanism and location with respect to the site. The seismic performance of slopes is typically evaluated based on the sliding displacement predicted to occur along a critical sliding surface. Various empirical models are available that predict sliding …

Behavior Of Geothermal Energy Piles Embedded In Rock, Ehab Sabi

Civil and Environmental Engineering Theses and Dissertations

Geothermal energy piles are categorized as closed systems. Energy piles are a relatively new technology which couples the structural role of traditional pile foundations to that of heat exchangers to fulfill the required energy demand of buildings and infrastructures. These foundations are equipped with pipes embedded in the concrete forming the pile. While connected to a heat pump, the fluid circulating inside these pipes provides the exchange of heat with the ground for heating and cooling purposes. As the undisturbed temperature at the shallower depths of the ground stays comparatively constant the whole year, being warmer than the surrounding temperature …

Civil Engineering Design Of Cornhusker Council's Outdoor Education Center, Kelly Weiler

Honors Program: Senior Projects (Public)

A team of geotechnical, structural, hydraulic, environmental, and transportation experts collaborated to provide engineering solutions to the Cornhusker Council in an effort to solve the current problems facing their Outdoor Education Center. This results of this project provided the structural design of three bridges on the property, transportation plans for two parking lots and roadway design, geotechnical recommendations for soil testing and erosion prevention, and an environmental and hydraulic analysis of the property. A major challenge in the design of this project is the consideration of the dangers and regulations that accompany the floodway and floodplain regions on site. Various …

Modeling Of Fluid Injection For Hydraulic Fracturing Initiation In Porous Rock Formations, Krishna Adhikari

LSU Master's Theses

Hydraulic fracturing has been widely opted in recent times to simulate the unconventional reservoirs and thus, has become key a subject of interest in petroleum engineering. The stress concentration around the borehole affects the breakdown pressure and fracture reopening pressure during the hydraulic fracturing treatments. Thus, the state of stress around borehole wall and its surrounding rocks due to instantaneous drilling and a fluid injection at borehole surface needs to be determined accurately to initiate the hydraulic fractures. This research intends to derive the analytical stress solution of inclined borehole subjected to time-dependent fluid injection and in-situ stress, verify the …

Influence Of Limit Equilibrium Methods In The Design Of Contiguous Cantilever Sheet Pile Walls Through Reliability-Based Analysis, Alvaro J. Mattos, Juan Camilo Viviescas, Juan Pablo Osorio

Conference papers

In geotechnical engineering the design of bored- pile walls is commonly performed in terms of the embedment length (D) defined according to the limit equilibrium methods (also known as balance methods) formulated by Krey, Blum, Rowe, Hansen and the empirical method of Look in sandy soils. The limit equilibrium methods are calculations associated with the shape of the earth pressures distributions in the shaft, earth pressures theories, geotechnical properties and safety factors, while the empirical criteria establish that the relationship between embedment and the free height (H) is of the order of D/H = 1.5. These design methods are complemented …

Analysis Of The Pile Load Tests At The Us 68/Ky 80 Bridge Over Kentucky Lake, Edward Lawson

Theses and Dissertations--Civil Engineering

Large diameter piles are widely used as foundations to support buildings, bridges, and other structures. As a result, it is critical for the field to have an optimized approach for quality control and efficiency purposes to measure the suggested number of load tests and the required measured capacities driven piles. In this thesis, an analysis of a load test program designed for proposed bridge replacements at Kentucky Lake is performed. It includes a detailed site exploration study with in-situ and laboratory testing. The pile load test program included monitoring of a steel H-pile and steel open ended pipe pile during …

Synthesis Of Fault Traces In Se Louisiana Relative To Infrastructure, David Culpepper, Elizabeth Chinn Mcdade, Nancye Dawers, Mark Kulp, Rui Zhang

Data

Corresponding data set for Tran-SET Project No. 17GTLSU12. Abstract of the final report is stated below for reference:

"Geological faulting has been implicated as a contributor to subsidence, coastal land-loss and submergence of marshlands in southern Louisiana. This report reviews whether fault motion, either by slow creep or more sudden slip, can cause deformation of engineered structures resulting in increased infrastructure maintenance and repair costs. The impact of surface, or near-surface, geologic faulting on critical infrastructure is insufficiently documented in southeastern Louisiana, but the state has a vast amount of energy-sector subsurface data that to date has been under-utilized for …

Investigation Of Dredge Material Dewatering Through Hydraulic And Ground Improvement Methods, Monica Moody

Williams Honors College, Honors Research Projects

Every year almost 1.5 million tons of material is dredged from Lake Erie to allow passage for boat traffic. In the past, this material has been placed back into the open waters of the lake. However, starting July 2020 this will no long be permitted due to the passing of Senate Bill 1. Therefore, secondary uses of this dredging material are being investigated. To be used, the material needs to be quickly dewatered and stabilized. This project consists of literary reviews of two methods of rapid dewatering, hydraulic placement and ground improvement methods. Hydraulic placement dewatering requires the use of …

Stabilization Of Dredged Materials In Ohio: An Investigation Of Mechanical, Chemical And Biological Dewatering Techniques, Erika Howard

Williams Honors College, Honors Research Projects

Each year, materials are excavated from oceans and lakes in order to keep the waterways open so that ships can safely pass through. These excavated, or dredged, materials are then discarded, usually being returned to the body of water from which they were removed. Beginning in 2020, the Ohio Environmental Protection Agency (OEPA) will no longer allow this to occur. Therefore, the purpose of this project is to investigate beneficial uses for dredged materials in Lake Erie, and to address the best management practices for dewatering these materials, as set forth in the Lake Erie Protection and Restoration Plan created …

Finite Element Modeling Of Mechanically Stabilized Earth Walls Built With Welded Wire Wall Panels, Dejuan G. Solan

College of Graduate Studies: Theses & Dissertations

In this thesis, a finite element modeling of Mechanically Stabilized Earth (MSE) walls using welded wire wall panels was performed. The implementation of finite element modeling and analysis proved to be quite efficient in simulating the three-dimensional behavior of wall panels that are a part of MSE walls. The comprehensive finite element model included defined concrete and steel material properties in order to present both the realistic behaviors of each component in the model as well as better facilitating and increasing the accuracy of the simulation of numerous finite element analysis (FEA) cases. FEA was employed to simulate welded wire …

Synthesis Of Fault Traces In Se Louisiana Relative To Infrastructure, David Culpepper, Elizabeth Chinn Mcdade, Nancye Dawers, Mark Kulp, Rui Zhang

Publications

Geological faulting has been implicated as a contributor to subsidence, coastal land-loss and submergence of marshlands in southern Louisiana. This report reviews whether fault motion, either by slow creep or more sudden slip, can cause deformation of engineered structures resulting in increased infrastructure maintenance and repair costs. The impact of surface, or near-surface, geologic faulting on critical infrastructure is insufficiently documented in southeastern Louisiana, but the state has a vast amount of energy-sector subsurface data that to date has been under-utilized for transportation and other near-surface engineering applications. Recent and on-going work by research groups at Tulane University, University of …

Use Of Wicking Geotextile To Dehydrate Road Embankments, Chuang Lin

Doctoral Dissertations

“Excess water within a pavement structure is the major cause of pavement deteriorations. A roadway is often constructed with soils compacted at the optimum water contents to achieve the best performance. After construction, the soil water content variation is controlled by the ambient environment. The base course aggregate is very sensitive to water content variations. Unfortunately, conventional drainage system can only drain gravity water, but not capillary water, and it cannot work under unsaturated conditions. Consequently, no matter how well the road is constructed, the water content is expected to increase with time and the excess water will inevitably accelerate …

Laboratory Evaluation Of Recycled Crushed Glass Cullet For Use As An Aggregate In Beach Nourishment And Marsh Creation Projects In Southeastern Louisiana, John C. Wildman

LSU New Orleans Theses and Dissertations

To combat the rapid degradation of the Louisiana coast, the Louisiana Coastal Protection and Restoration Authority has planned strategic land building initiatives throughout the Louisiana Gulf coast, including beach nourishment and marsh creation projects. It is commonly agreed that the state lacks sufficient renewable sediment resources to maintain the planned CPRA land building program. However, Louisiana, the state that commonly ranks last in state recycling percentage, recycles an estimated 0.6% of the waste glass consumed in the state. Glass is predominantly silica sand. This thesis evaluates laboratory‑determined characteristics of recycled crushed glass cullet to assess its suitability as a renewable …

Evaluation Of A Centrifuge Consolidation Technique To Determine The Effects Of Temperature And Time On Kaolinite Properties, Esteban Miranda Pinzon

Civil Engineering Undergraduate Honors Theses

Abstract

The effects of time and temperature on the moisture content and unit weight profiles, as developed during a centrifuge consolidation process, were observed during the research program that is described herein. Specifically, a Beckman-Coulter Model J6-MI centrifuge with a six-place JS-4.2A swinging bucket rotor was utilized to consolidate kaolinite slurry samples. The consolidation procedure utilized specially designed slurry consolidometers, made from acrylic tubes with inside diameters of 2.63 inches (6.67 cm) and heights of 5.13 inches (13.04 cm). The tested kaolinite slurry samples were created by mixing 400 grams of dry kaolinite clay powder with 200 grams of de-aired …

Young’S Modulus As A Measurement To Estimate Damage Related With Alkali-Silica Reaction In Concrete., Anazaria J. Ortega Gonzalez

Civil Engineering Undergraduate Honors Theses

The main purpose of this research is to compare two nondestructive methods to assess Alkali-Silica reaction (ASR) in concrete. Fifteen concrete prisms were cast using aggregates with different Alkali-Silica reactivity such as Jobe sand and Van Buren sand. The change in strain, shear wave velocity and Young’s modulus were determined according to ASTM C129 and ASTM C215, respectively. This data was collected by Dillon K Self, who determined that the shear wave velocity and strain are inversely proportional. However, when single cracking in the concrete specimen transition to map cracking, the shear wave velocity dropped significantly, whereas the strain value …

Utilizing The Hvsr Second Peak For Surface Wave Inversions In The Mississippi Embayment, Ashraf Kamal Himel

Graduate Theses and Dissertations

Ambient noise data from 24 sites within the Mississippi Embayment were analyzed to estimate the fundamental frequency using the horizontal to vertical spectral ratio (HVSR) method. The fundamental frequency ranged from 0.17 to 3.43 Hz for the tested sites. At seventeen of the sites, a second higher frequency HVSR peak, which ranged from 0.617 Hz to 2.154 Hz, was observed in addition to the fundamental HVSR peak. The second peak frequency in the HVSR curve has been attributed by previous researchers as either an odd harmonic of the fundamental peak or a shallow impedance contrast from the Memphis sand layer …

Examining The Use Of Idealized Granular Material In Validated Dem Simulations, Anjana Thoroppady Kittu

Graduate Theses and Dissertations

Discrete element method (DEM) modeling, is becoming widely used for understanding the micro-mechanical behavior of granular materials at the particle level. This dissertation presents important considerations regarding the experimental boundary conditions and idealized granular materials used in DEM validations.

A common issue in DEM validation studies for direct shear and direct simple shear is selecting top and bottom cap boundary conditions that allow for shear transmission while also being efficiently modeled in the DEM simulations. While the traditional grid boundary types used in the laboratory can be replicated in the numerical models, researchers have also used fixed-particle boundaries, sawtooth boundaries, …