Environmental Engineering Commons^™

Tsunamigenic Potential Of The Baiyun Slide Complex In The South China Sea, Linlin Li, Fengyan Shi, Gangfeng Ma, Qiang Qiu

Civil & Environmental Engineering Faculty Publications

The Baiyun slide complex contains geological evidence for some of the largest landslide ever discovered in the continental slopes of the South China Sea. High-resolution seismic data suggest that a variety of landslides with varied scales have occurred repeatedly in this area. The largest landslide reconstructed from bathymetric and seismic data has an estimated spatial coverage of ~5,500 km² and a conservative volume of ~1,035 km³. Here, using geomorphological and geotechnical data, we construct a series of probable landslide scenarios and assess their tsunamigenic capacity. By treating the slides as deformable mudflows, we simulate the dynamics of …

Geophysical Delineation Of Megaporosity And Fluid Migration Pathways For Geohazard Characterization Within The Delaware Basin, Culberson County, Texas, Jonathan David Woodard

Electronic Theses and Dissertations

ABSTRACT

Differential dissolution of gypsum karst within the Delaware Basin poses a significant threat to infrastructure that society depends on. The study area is located in Culberson County, Texas and traverses a distance of approximately 54 kilometers along RM 652 within the Gypsum Plain which is situated on the northern margin of the Chihuahua Desert and includes outcrops of Castile and Rustler strata that host karst geohazards. Regions of karst geohazard potential have been physically surveyed proximal to the study area in evaporites throughout the Castile Formation outcrop; minimal hazards, in comparison to the Castile Formation, have been documented in …

Characterization And Delineation Of Karst Geohazards Along Rm652 Using Electrical Resistivity Tomography, Culberson County, Texas, Adam F. Majzoub

Electronic Theses and Dissertations

The Delaware Basin of West Texas and southeastern New Mexico is the major western subdivision of the Permian Basin and a northern extension of the Chihuahuan Desert. The major evaporite unit within the Delaware Basin is the Castile Formation, which consists of gypsum/anhydrite and is highly susceptible to dissolution and karsting. Manifestations of karst within the Castile outcrop are abundant and include sinkholes, subsidence features and caves, both epigene and hypogene in origin.

Land reconnaissance surveys conducted during the summer of 2015 documented abundant karst landforms in close proximity to a major thoroughfare, RM 652, in Culberson County, Texas. 2D …

Imaging Reinforced Concrete: A Comparative Study Of Ground Penetration Radar And Rebarscope, Abhishek Kodi

Masters Theses

"Geophysical techniques have been playing a very vital role in subsurface imaging in the recent past. Technology has been making it both reliable and convenient to utilize non-destructive geophysics techniques like Ground Penetration Radar, Induction current based Rebarscope, Seismic methods, ERT, etc. The applications range from shallow subsurface investigation of Bridge decks to old tunnels, mapping of rabars in a pre-existing construction and analyzing the concrete strength.

The thesis constitutes of a comparative study and analysis of a Ground Penetration Radar system and a Rebarscope. Individual parameters obtained directly from the study and obtained indirectly from the study shall be …

Hydrogeological And Thermal Sustainability Of Geothermal Borehole Heat Exchangers, S. Emad Dehkordi

Electronic Thesis and Dissertation Repository

Assessment of the current approach taken by guidelines and design methods of vertical closed loop heat exchangers shows that often groundwater flow is either disregarded or is not methodically incorporated. The state of scientific research in this arena reveals that overlooking the groundwater flow in the design procedure may not always be a correct assumption. The significance of advective heat transport compared to conduction is defined by the groundwater flux or Darcy velocity which heavily depends on the hydraulic conductivity of the ground, followed by the hydraulic gradient which has a relatively limited range. A sensitivity analysis on ground and …

The Reduction Of Storm Surge By Vegetation Canopies: Three-Dimensional Simulations, Y. Peter Sheng, Andrew Lapetina, Gangfeng Ma

Civil & Environmental Engineering Faculty Publications

Significant buffering of storm surges by vegetation canopies has been suggested by limited observations and simple numerical studies, particularly following recent Hurricanes Katrina, Rita, and Wilma. Here we simulate storm surge and inundation over idealized topographies using a three-dimensional vegetation-resolving storm surge model coupled to a shallow water wave model and show that a sufficiently wide and tall vegetation canopy reduces inundation on land by 5 to 40 percent, depending upon various storm and canopy parameters. Effectiveness of the vegetation in dissipating storm surge and inundation depends on the intensity and forward speed of the hurricane, as well as the …

Role Of Forward Model In Surface-Wave Studies To Delineate A Buried High-Velocity Layer, Xiaohui Jin, Barbara Luke, Carlos Calderon-Macias

Civil and Environmental Engineering and Construction Faculty Research

Procedures are tested and compared for processing Rayleigh surface wave data to obtain one-dimensional shear wave velocity profiles for a hypothetical site that contains a buried high-velocity layer (HVL). The main purpose of such an investigation would be to discriminate and characterize the HVL. When target dispersion curves are derived from synthetic time histories, for the most part, the HVL is better identified when profiles are inverted using only the fundamental mode of Rayleigh wave propagation, rather than a more compatible but more complex forward model. The outcomes imply that in practice, a simple forward model might be more successful …

Interpreting Surface-Wave Data For A Site With Shallow Bedrock, Daniel W. Casto, Barbara Luke, Carlos Calderon-Macias, Ronald Kaufmann

Civil and Environmental Engineering and Construction Faculty Research

The inversion of dispersive Rayleigh-wave data has been shown to be successful in providing reliable estimated shear-wave velocities within unconsolidated materials in the near surface. However, in a case where the multi-channel analysis of surface waves method was applied to a site consisting of clay residuum overlying basalt bedrock, inversion for the fundamental-mode Rayleigh wave resulted in shear-wave velocities within the rock that are less than half of expected values. Forward modeling reveals that the fundamental-mode dispersion curve is hardly sensitive to bedrock velocity perturbations over a practical range of wavelengths, leading to poorly constrained solutions. Standard surface-wave methods can …

Studies In Modulation Of Interfacial Reactions For Certain Sulphide Minerals, Robert Owen Beyaert

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Production Of Standard-Grade Ferromanganese In An Electric Arc Furnace, Force F. Baney Jr.

Bachelors Theses and Reports, 1928 - 1970

The investigations conducted in this project were essentially concerned with the effects of various compositions of two different slag systems upon the increased recovery of manganese in a standard-grade ferromanganese.

Investigation Of The Ternary System Silver-Aluminum-Indium (Ag-Al-In), Elvin H. Beardslee

Bachelors Theses and Reports, 1928 - 1970

This thesis paper contains material pertaining to & preliminary investigation of the ternary system Ag-Al-In. Procedures in this preliminary investigation are discussed in detail.

Preliminary Examination Of The Aluminum Corner Of The Ternary System Aluminum-Silver-Indium (A1-Ag-In), Jerome J. Blake

Bachelors Theses and Reports, 1928 - 1970

In this paper the author attempts to lay the groundwork for future work on the Al-Ag-In system.

Crystal Habit Modification Of Sodium Chlorate, Michael R. Keegan

Bachelors Theses and Reports, 1928 - 1970

All single crystals have a particular habit or morphology. The crystal habit refers to the relative degree of development of crystallographic planes into surfaces which make up the external appearance of the single crystal.

In this paper, NaClO3 is used as a parent crystal. Its simple cubic habit is modified to tetrahedral by the use of impurities of SO4=, S2O3=, Cr2O7=, and NO3-. The degree of habit change is studied as a function of impurity concentration and temperature. The problem and phenomena are explained in terms of surface chemistry and thermodynamics.

Physico-Chemical Principles Of Sixteenth Century Metallurgy, Robert E. Johnson

Bachelors Theses and Reports, 1928 - 1970

Following a review of sixteenth century metallurgical literature and a discussion of Gibbs free energy, this thesis discusses thermodynamic considerations of galena (PbS) reduction by iron from a lead assay of this period. The importance of fluxes in this assay is emphasized. The discussion covers both equilibrium and non-equilibrium conditions at 1100 degrees Celsius. Possible substitutes for iron are also covered.

Information from twenty-one small controlled lead assays is correlated with the thermodynamic discussion to determine the purpose of each constituent in the assay.

The Beneficiation Of Titaniferous-Magnetite Sands, Ronald Lloyd Nordwick

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation of beneficiation methods is to develop and study possible economic methods for recovering an iron-titanium concentrate of sufficient purity to meet metallurgical requirements for subsequent direct reduction to pig iron and a high titanium slag.

Stress-Corrosion Cracking Of Brass, Paul A. Fossey

Bachelors Theses and Reports, 1928 - 1970

the mechanism of stress-corrosion cracking of brass has been sought for many years. Investigators have proposed many mechanisms, but each of these mechanisms has always had several drawbacks. This paper presents an account of experimental work done in the laboratory on this subject and compares it to the work of previous investigations. It evaluates the mechanisms presented by investigators and shows the failures of these mechanisms. A theory of Nitrogen Embrittlement is presented and an evaluation of this theory with experimental work follows.

Experimental Arc Furnace Smelting Of Titaniferous Iron Sands From The Northern Oregon Coast, Allan P. Herring

Bachelors Theses and Reports, 1928 - 1970

This investigation is an attempt to experimentally smelt titaniferous iron sands from the Northern Oregon Coast in a laboratory arc furnace.

The Effect Of Ph Upon Chelation Reactions In Montmorillonite Clays, Joseph Michael Keane

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to investigate several chelation reactions and determine the effect of variable pH upon these reactions.

An Investigation Of The Sintering Of Iron-Wire Compacts, George L. Vivian

Bachelors Theses and Reports, 1928 - 1970

A study of the sintering of iron has been made by observing the rate of bonding of iron wires wound on iron spools. The specimens were sintered at a constant temperature of 850c in vacuum furnaces capable of producing pressures of 10-5 to 10-4 mm of mercury, and the growth of the bond between wires was observed as a function of time.

It has been concluded that the volume-diffusion mechanism is strongly operating in the sintering of iron at 850c, but in an evacuated system, the evaporation-condensation mechanism also contributes to the sintering process.

The Identification Of Montana Clays By X-Ray Analysis, David Stephen Malyevac

Bachelors Theses and Reports, 1928 - 1970

The purpose of this study is to identify the various Montana clay minerals by means of X-ray diffraction. The ultimate aim of this investigation is to identify the different clay mixtures through an analysis of their respective diffraction patterns, and diffraction patterns obtained after various chemical and thermal treatments.

Effect Of Recovery On The Recrystallized Grain-Size Of High Purity Aluminum, Rodney L. Helterline

Bachelors Theses and Reports, 1928 - 1970

When a cold-worked metal is annealed, it’s physical properties hange as a result of a new grain structure. The annealing treatment is divided into three stages according to the changes that occur in the distorted metal: (1) recovery, (2) recrystallization, and (3) grain growth.

Investigation Of Inclusions In Armco Ingot Iron, Edwin J. Duncan

Bachelors Theses and Reports, 1928 - 1970

Various chemical and electrolytic separation methods were investigated in an attempt to separate the in­clusions in Armco ingot iron. Residues obtained were X-rayed for identification purposes. The microstruc­tures of this iron were studied with the object of de­termining the relative sizes, locations, and possible compositions of the inclusions.

The Design And Construction Of An Electrolytic Cell For Aluminum Reduction, Thomas H. Melrose

Bachelors Theses and Reports, 1928 - 1970

The purpose of this investigation was to design and construct a laboratory size electrolytic cell in which to reduce alumina, using the same basic materials that are used in a commercial size cell. The cell was designed to have a capacity of approxi­mately 100 grams of metallic aluminum produced every 8 hours. The cell was constructed so it could be operated continuously.

Polarography Of Indium, John Jackson

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to study the various aspects of the polarography of indium. The eventual goal would be to develop a method of analyzing indium in unknowns. The investigation is approached by studying the indium ions in various electrolytes and in various concentrations.

Geology Of The Ragged Point Oil Field Musselshell County, Montana, David M. Amos

Bachelors Theses and Reports, 1928 - 1970

The Ragged Point oil field is located in Northwest Musselshell County, in the Lake Basin field of central Mon­tana, and on the western border of the Great Plains region. The surface topography is that of a plain marked by erosion and moderate folding. The stratigraphy of central Montana shows periodic marine invasions from the Cordilleran trough, with normal marine limestones interbedded with sandstone sand shales. These sediments are over 12,000 feet thick, with the Creta­ceous Eagle and Colorado formations exposed at the surface on the Ragged Point anticline. Undifferentiated Cambrian lime­stones and shales are the oldest rocks encountered in drilling.

The Application Of Electric Energy To The Metallurgy Plants In Montana, Edwin J. Duncan

Bachelors Theses and Reports, 1928 - 1970

Since the year 1800, metallurgy has been affiliated with electricity. In fact, the two industries have grown side by side, being naturally dependent upon each other and having a parallel growth.

The Construction And Operation Of A Universal Specimen Mount With Protective Lead Shield For The Purpose Of Determining Pole Figures Using The Schulz-Decker Transmission Technique, Richard L. Fausner

Bachelors Theses and Reports, 1928 - 1970

It was the purpose of this study to construct a universal mount, to construct a protective lead shield, to operate the instrument, and to provide a pole figure using the transmission method of Schulz and Decker. There are at present several lengthy x-ray methods of determining the grain orientation of metals. These methods are mainly photographic. In order to provide a rapid means of obtaining the necessary information concerning the grain orientation of a metal, a universal mount was constructed.

The Lucky Hit Mine Of Jefferson County, Montana, Bruce B. Goddard

Bachelors Theses and Reports, 1928 - 1970

Many mines in the Cardwell Mining District have been more or less steady producers of gold, silver, lead and zinc since 18SO. The area first came into prominence with the discovery of gold at the Mayflower Mine in 1896. Soon after the Mayflower discovery, many claims were located in the nearby Saint Paul Gulch area, northeast of Whitehall. The Lucky Hit Mine is located in Saint Paul Gulch area of the Cardwell Mining District.

Nonmetallic Mineral Resources Of Montana (Except Fuels), F. L. Rytlewski

Bachelors Theses and Reports, 1928 - 1970

Essentially, the paper is composed of seven parts, each of which concerns a group of related nonmetallic minerals such as ceramic materials, gemstones, or abra­sives. Following the data pertaining to the minerals of each group are index mars locating the major mineral deposits which are known to date. Production and reserve figures are listed by tables in cases where such information is available.

The Flotation Concentration Of A Complex Low-Grade Lead Zinc Ore, Edward James Fong

Bachelors Theses and Reports, 1928 - 1970

This report is concerned primarily with the beneficiation of a low-grade complex lead-zinc ore. The depletion of high grade veins has caused the mineral engineer to seek deposits deeper in the earth's crust or to find lower grade deposits. The other alternative has placed more research problems on Mineral Dressing Engineers in particularly the iron, copper, lead and zinc fields.