Construction Engineering and Management Commons^™

Service Life And Life-Cycle Assessment Of Reinforced Concrete With Fly Ash And Limestone Calcined Clay Cement, Ravindra Gettu, Radhakrishna G. Pillai, Manu Santhanam, Sundar Rathnarajan, Anusha Basavaraj, Sripriya Raju, Yuvaraj Dhandapani

International Conference on Durability of Concrete Structures

Environmental impact due to the emission of carbon dioxide during concrete production can be taken care by reducing the clinker content in the cement. The clinker content can be reduced by replacing it with fly ash and limestone calcined clay. Such systems can have a potential to exhibit enhanced durability/service life when exposed to chloride and carbon dioxide. However, estimating probabilistic service life of concretes with such alternative binder systems is difficult due to the lack of quantitative estimates of the input parameters such as chloride diffusion coefficient (D_Cl), ageing coefficient (m), carbonation coefficient (K_CO2), and …

Transport Properties And Strength Development Of Blended Cement Mortars Containing Nano-Silica, Ali Akbar Ramezanianpour, Sajjad Mirvalad, Mehrdad Mortezaei

International Conference on Durability of Concrete Structures

In the present study, the mechanical properties and durability of blended cement mortars containing nanosilica and natural pozzolans is investigated. Trass and pumice, two different Iranian natural pozzolan, are used in the experiments. For cement blends preparation, nano-silica replacement levels of 2, 3 and 4% by mass of cement was considered; each mixture contained one of the natural pozzolans with a fixed replacement percentage of 15. The Standard mortar samples were made with w/cm ratio of 0.485; the flow of all mortars ranged from 14 to 16 cm. All prepared mortars’ samples were cured in saturated limewater until the test …

A Co-Optimal Coverage Path Planning Method For Aerial Scanning Of Complex Structures, Zhexiong Shang, Justin Bradley, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

The utilization of unmanned aerial vehicles (UAVs) in survey and inspection of civil infrastructure has been growing rapidly. However, computationally efficient solvers that find optimal flight paths while ensuring high-quality data acquisition of the complete 3D structure remains a difficult problem. Existing solvers typically prioritize efficient flight paths, or coverage, or reducing computational complexity of the algorithm – but these objectives are not co-optimized holistically. In this work we introduce a co-optimal coverage path planning (CCPP) method that simultaneously co-optimizes the UAV path, the quality of the captured images, and reducing computational complexity of the solver all while adhering to …

Participatory Sensing-Based Geospatial Localization Of Distant Objects For Disaster Preparedness In Urban Built Environments, Hongjo Kim, Youngjib Ham

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Although the benefit of participatory sensing for collecting local data over large areas has long been recognized, it has not been widely used for various applications such as disaster preparation due to a lack of geospatial localization capability with respect to a distant object. In such applications, objects of interest need to be ro- bustly localized and documented for supporting data-driven decision-making in site inspection and resource mobilization. However, participatory sensing is inappropriate to localize a distant object due to the absence of ranging sensors in citizens' mobile devices; thus, the localization accuracy varies to a large extent. To address …

Bs News November/December

Building Services Engineering

No abstract provided.

Exploring Occupant Behavioral Intentions In Immersive Virtual Environment To Enhance The Design And Engineering Of Sustainable Buildings, Sanaz Saeidi

LSU Doctoral Dissertations

Accurately simulating occupant behavior is essential to improve our understanding about the future energy performance of the buildings. To date, most of the information related to the occupancy behaviors has been gathered through field observations and/or performing experiments within the lab environments. Even though these common data collection methods are effective and reliable for the existing buildings, using such data to project occupant behaviors in other contexts is likely to lead to uncertainties. The most significant theoretical achievement of this dissertation was to provide the future building occupants with thermal experience of non-physically existent environments. In this dissertation occupant behavior …

Organizational Criteria To Assess Adaptive Capacity In Complex Systems, Abdulrahman Alfaqiri

October 11, 2019: Measuring and Evaluating Resilience

No abstract provided.

Effect Of Light Activated Self-Healing Polymers On The Performance Of Asphalt Pavement Containing Recycled Asphalt Materials (Rap/Ras), Sharareh Shirzad

LSU Doctoral Dissertations

A new generation of Ultraviolet (UV) light-induced self-healing polymers was introduced for the asphalt pavement application with the aim to enhance pavements durability while increasing its service life. The developed self-healing polymer was mixed with asphalt binder using two different methods, passive and reactive. For the passive method, the cured self-healing polymer was ground to smaller particle size and then it was mixed with asphalt binder using a high shear stirrer and at a high temperature. For the reactive method, self-healing polyurethane pre-polymer was added to the asphalt binder at a lower temperature and lower shear rate compare to the …

Vu Villa Structural Design And Rehabilitation, Kolby Sukut

Graduate Theses & Non-Theses

The Vu Villa is a bar and pizzeria which has operated out of the first floor of the Campana building in Butte, Montana since 1967. Construction of the Campana building started in 1894 and was completed before the end of the 19^th century. The Campana building is a two-story building which primarily consists of exterior brick masonry walls and wood framing on the interior. Within the last several decades significant sag has been identified in the second-floor of the building as well as an adjacent staircase. In addition, renovation activities have been discussed for the upstairs which would involve …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Data

Corresponding data set for Tran-SET Project No. 18STTAM01. Abstract of the final report is stated below for reference:

"This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs …

Simulation Of The Impact Of Connected And Automated Vehicles At A Signalized Intersection, Hamad Bader Almobayedh, Deogratias Eustace, Philip Appiah-Kubi

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Intersections are locations with higher likelihood of crash occurences and sources of traffic congestion as they act as bottlenecks compared with other parts of the roadway networks. Consequently, connected and automated vehicles (CAVs) can help to improve the efficiency of the roadways by reducing traffic congestion and traffic delays. Since CAVs are expected to take control from drivers (human control) in making many important decisions, thus they are expected to minimize driver (human) errors in driving tasks. Therefore, CAVs potential benefits of eliminating driver error include an increase in safety (crash reduction), smooth vehicle flow to reduce emissions, and reduce …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Publications

This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs and other multifunctional materials can be considered as a replacement for components made of steel (e.g., in reinforced …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Publications

This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The results of the testing showed that for the selected Soil-RAG-Geopolymer mixtures the strength, stiffness, permanent deformation, and durability …

The Professional Constructor, Full Issue, Volume 44, Number 02

The Professional Constructor

No abstract provided.

An Investigation Into Current Procurement Strategies That Promote Collaboration Through Early Contractor Involvement With Regards To Their Suitability For Irish Public Work Projects, Barry Mcauley, Frederic Lefebvre

Conference papers

Previous research has established that multi-disciplinary collaboration will benefit a construction project throughout its lifecycle. While Lean Construction, Building Information Modelling (BIM), and Integrated Project Delivery (IPD) can all be viewed as separate processes which add independent value to a project, they are more effective when used in partnership with each other. In order to ensure the high levels of collaboration expected for these processes to work in unison, the early involvement of the Contractor is paramount. Early contractor involvement within the design process can ensure a more focused integrated project team, improvement of both constructability and cost certainty, as …

Improving The Sustainability Of The Built Environment By Training Its Workforce In More Efficient And Greener Ways Of Designing And Constructing Through The Horizon2020 Bimcert Project, Barry Mcauley, Avril Behan

Conference papers

The construction industry consumes up to 50% of mineral resources excavated from nature, generates about 33% of CO2 present in the atmosphere and is responsible for 40% of total global energy through both construction and operation of buildings. The realisation that current pervasive construction practices now face globalization, sustainability, and environmental concerns, as well as ever-changing legislation requirements and new skills needed for the information age has resulted in technologies such as Building Information Modelling (BIM) becoming a key enabler in navigating these barriers. To assist in overcoming these barriers, a number of funding initiatives have been put in place …

From Roadmap To Implementation: Lessons For Ireland’S Digital Construction Programme, Barry Mcauley, Alan Hore, Roger West

Conference papers

As part of their Future of Construction initiative in 2018 the World Economic Forum published an action plan to accelerate Building Information Modelling adoption. The WEF report highlighted actions that companies, industry organisations and governments are advised to implement to accelerate BIM adoption and better capitalise on delivering better project outcomes. According the authors of the report BIM is seen as the centrepiece of the construction industry’s digital transformation, however they acknowledged that BIM adoption globally remain slow. Anecdotal experience would suggest that BIM usage in Ireland is also very low and that a similar initiative or an adaptation of …

Bim In Ireland 2019: A Study Of Bim Maturity And Diffusion In Ireland, Barry Mcauley, Alan Hore, Roger West

Conference papers

In 2017, the BIM Innovation Capability Programme team applied five macro BIM maturity conceptual models to capture the capability of the Irish construction industry and assess its BIM maturity. The results found that while Ireland is mature for modelling processes, it is less developed with regards to collaboration processes and policies. Ireland also ranked poorly when it came to regulatory frameworks, measurements and benchmarks compared to a number of countries which also applied the same conceptual models. At the time, the findings highlighted that Ireland’s diffusion dynamic was middle out, meaning that larger organisations or industry associations were pushing the …

Centres Of Excellence And Roadmaps For Digital Transition: Lessons For Ireland’S Construction Industry, Barry Mcauley, Alan Hore, Roger West

Conference papers

Like most sectors in today’s working world, construction businesses are challenged to work in an increasingly digitised world with sophisticated demands from intelligent clients. So much has been written about the inefficiencies of the construction industry, its fragmentation, lack of collaboration, low margins, adversarial pricing, poor productivity, financial fragility, lack of research and development, poor industry image and relatively weak use of digital solutions. The Irish government recognises the importance of digital innovation to address many of the challenges the construction industry faces. With recent high profile reports of escalating spend on signature public sector projects and weak productivity performance …

Delivering Energy Savings For The Supply Chain Through Building Information Modelling As A Result Of The Horizon 2020 Energy Bimcert Project, Barry Mcauley, Avril Behan

Conference papers

The global buildings sector is now responsible for 40% of final energy consumption as well as accounting for 33% of energy-related carbon dioxide emissions. This has resulted in a growing urgency to address energy and emissions from buildings and construction, to meet restrictive 2020 targets as specified by the European Union (EU). To achieve these targets a number of funding initiatives have been put in place through Horizon 2020 with a focus on BIM, due to it having the potential to rapidly produce energy outputs that enable design teams to analyse and compare the most cost-effective, energy-efficient options. However, despite …

Competitive Strategies In Small And Medium Sized Enterprises (Sme's): A Cross- Case Analysis Of Irish Construction Professional Service Firms, Oluwasegun O. Seriki, Roisin Murphy

Conference papers

Strategy formulation aims to attain strategic fit between an organisation and its business environment in pursuit of competitive advantage. Although competitive strategy research is long established within industries such as manufacturing, financial services and IT, strategy within construction is still under-investigated by comparison. For construction professional service firms (CPSFs), the dearth of academic inquiry is even more apparent, partly due to the intangible nature of their service offerings, highly customised nature of their services and reliance on intellectual capital. The Irish construction sector is experiencing stable growth since following a prolonged recession, thus understanding the strategy process within professional service …

Effects Of Organizational Trust And Project Delivery Variables On Bim User Confidence, Jason D. Lucas, Saw Sri Neeharika Vijayarao

The Professional Constructor

The use of Building Information Models (BIM) for construction planning has increased in all areas except for automated processes such as quantity take-off. Many model users lack confidence that a model, typically created by a third party, has accurate enough information in it to rely on the data for planning the project. This research is looking at how factors of organization trust and variables related to project delivery can raise user confidence in these situations. Factors of organizational trust were identified through a literature review. Two surveys were utilized to identify which factors were significant in raising user confidence. Finally, …

Accuracy Of Drone Based Surveys To Measure Stockpile Volume, Joseph M. Burgett, Scott Shaffer, Eric Stuckey

The Professional Constructor

This paper outlines a two phase experiment evaluating the accuracy of volumetric calculations using a commercially available drone and structure-from-motion (SfM) software. In the first phase, a large cardboard pyramid with a known volume was used to simulate a stockpile. Using georeferenced images collected by a Phantom 4 Pro drone and the SfM software ContextCapture, the computed volumes ranged between 1.5% and 3.3% of the actual volume. In the second phase of the experiment, a photometric survey was created of a large SCDOT borrow pit. The volumetric calculations were computed using conventional survey practices and with drone collected images. There …

Mitigating Reflective Cracking Through The Use Of A Ductile Concrete Interlayer, Qian Zhang, Mohammad Khattak, Adway Das

Data

Corresponding data set for Tran-SET Project No. 18PLSU13. Abstract of the final report is stated below for reference:

"Reflective cracking is considered one of the most important issues that causes premature deterioration of composite pavements. Many types of mitigation methods have been studied in the past. However, they are either not effective in delaying the reflective cracking, or they only extend the service life by a few years. To address this critical issue and significantly extend the service life of the composite pavement, in this research, a ductile interlayer made of engineered cementitious composites (ECC) was proposed. It was hypothesized …

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Data

Corresponding data set for Tran-SET Project No. 18CTAM03. Abstract of the final report is stated below for reference:

"Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and …

Performance Of Drilled Shaft Under Combination Of Complicated Loads Under Hurricane Event, Jie Huang, Sazzad Bin-Shafique

Data

Corresponding data set for Tran-SET Project No. 18GTTSA02. Abstract of the final report is stated below for reference:

"This project includes experimental and numerical studies to investigate and assess the impact of vertical loads on a laterally loaded drilled shaft under various conditions. The experimental study includes lab testing and lab-scale load test to examine a drilled shaft subjected to vertical and lateral loads at a reduced scale. With the data obtained from the lab-scale testing, a numerical model was calibrated, which was used to perform a parametric study to scrutinize the effect of many possible factors such as soil …

Strategies For Prioritizing Needs For Accelerated Construction After Hazard Events, Fernando Moreu, Chao Wang, Xinxing Yuan, Laleh Ghanbari, Claudia Garrido

Data

Corresponding data set for Tran-SET Project No. 18PPLSU04. Abstract of the final report is stated below for reference:

"There is a need for rapid and responsive infrastructure repair and construction after natural disaster events such as hurricanes, wildfires, and tornadoes. These natural disasters often shut down basic infrastructure systems, as experienced recently in several Region 6 states as well as in other states around the country. Accelerated construction practices are often used in these situations to speed up the traditional, and often slow, project delivery process. However, after a natural disaster, several and different types of transportation infrastructure components are …

Mitigating Reflective Cracking Through The Use Of A Ductile Concrete Interlayer, Qian Zhang, Mohammad Khattak, Adway Das

Publications

Reflective cracking is considered one of the most important issues that causes premature deterioration of composite pavements. Many types of mitigation methods have been studied in the past. However, they are either not effective in delaying the reflective cracking, or they only extend the service life by a few years. To address this critical issue and significantly extend the service life of the composite pavement, in this research, a ductile interlayer made of engineered cementitious composites (ECC) was proposed. It was hypothesized that by adding a thin layer of highly ductile ECC material between the existing pavement and overlay, reflective …

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Publications

Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and environmentally friendly alternative than OPC. This research explores methods to develop GPC with desired properties and evaluate their …

Commercial Construction Schedule Collaborators And Current Scheduling Practices, Evan D. Bingham, Jay P. Christofferson, Mark Hutchings

The Professional Constructor

Construction mangers use the project schedule to communicate aspects of construction timing critical to project success. These schedules may be created using the collaboration of multiple project stakeholders or be the creation of a single manager. The tools used to create and communicate the schedule could range from hand drawn to critical path computer software. Because these practices may vary from company to company, commercial construction mangers can benefit from an understanding of common scheduling practices in the industry. This paper is a report of findings for commercial contractors working in the western United States. Construction managers working for 23 …