Construction Engineering and Management Commons^™

E-Construction Technologies For Efficient Highway Construction Inspections, Dhaivat Patel

Theses and Dissertations--Civil Engineering

Over recent years, organizations such as the Federal Highway Administration and Departments of Transportation across the United States have showed interest in automating highway construction processes. The addition of e-Construction and other advanced technologies can significantly improve the efficiency and safety of highway paving operations, specifically paving inspections. Activities such as collecting load tickets, tracking pavement lay-down temperatures, and monitoring roller movement are antiquated practices that DOT inspectors perform during paving operations. E-Ticketing, Paver Mounted Thermal Profiling, and Intelligent Compaction were proposed to automate paving inspections and were recently tested in two resurfacing pilot projects in the state of Kentucky. …

Redefining Construction “As-Built” Plans To Meet Current Kentucky Transportation Cabinet Needs, Victoria Lynn Lasley

Theses and Dissertations--Civil Engineering

As-built drawings are the traditional method used by the construction industry to record changes made during construction. As-builts provide valuable information for new design projects as well as rehabilitation and remediation projects. The completeness and accuracy of these plans are essential for transportation industries and their success. While the importance of as-builts is widely recognized, the process of creating them has proven to be difficult. It is a time consuming process and entities often lack the resources necessary to complete accurate and detailed as-builts. After an investigation of current as-built operations within State Transportation Agencies, recommendations have been made to …

Assessing Impact And Blast Resilience Of Polymer Coated Cementitious Materials, Murtaza Nalwala, Gabriel Nsengiyumva, Yong-Rak Kim

UCARE: Research Products

RESEARCH MOTIVATION The bridge piers are highly vulnerable to the impact and blast loads. The position in which they are constructed makes it difficult to install protective devices around them. By the current AASHTO standard, it is possible to under-design bridge piers for commercial vehicle impacts and other events such as blast.

OBJECTIVE To improve impact and blast resilience of bridge piers using polymeric coatings.

CONCLUSION Polymer coating of Portland cement concrete can be achieved with a good bonding. ü The polymeric coating seem to improve impact resilience of Portland cement concrete by increasing absorbed impact energy (i.e., area underneath …

In-Situ Mechanical Characterization For Compacted Aggregates, Douglas Cortes, Paola Bandini

Publications

The evaluation of compacted unbound aggregate layers is perhaps the most common undertaking in transportation-related projects. The assessment of compaction compliance in engineered fills, subgrades, subbases, and bases in roadways and railways is central to ensure longevity of ground transportation infrastructure. In many cases, premature failures in roadways that originate in the unbound aggregate layers can be traced back to inadequate compaction. These failures are preventable, provided the problem areas can be identified by a suitable field test during construction. The most widely used method for compaction assessment during construction is the nuclear density gauge (NDG) test. While the device …

Rheological Performance Of Bio-Char Modified Asphalt With Different Particle Sizes, Ran Zhang, Qingli Dai, Zhanping You, Hainian Wang, Chao Peng

Michigan Tech Publications, Part 1

To improve the performance of petroleum asphalt, bio-char was used as a modifier for a petroleum asphalt binder, in this study. The rheological properties of bio-char modified asphalt binders were compared with different particle sizes and contents, with one control and one flake graphite modified asphalt binder. Specifically, the bio-char modifiers with two particle sizes (ranging from 75 μm–150 μm and less than 75 μm) and three contents of 2%, 4%, and 8% were added into the asphalt binder. A flake graphite powder with particle sizes less than 75 μm was used as a comparison modifier. The Scanning Electron Microscopy …

Development Of Self-Healing Mechanisms For Asphalt Pavements, Max Abelardo Aguirre Deras

LSU Doctoral Dissertations

Self-healing mechanisms, such as microcapsules or hollow-fibers, filled with an asphalt rejuvenator present an emerging technology that would enhance an asphalt mixture’s resistance to cracking damage caused by vehicular and environmental loading. The objectives of this study were to: (a) Evaluate the effects of asphalt rejuvenators on hot-mix asphalt mixtures in order to test its effects on the fundamental engineering properties of the mixtures at high and intermediate temperatures; (b) Develop a synthesis procedure for production of microcapsules and hollow-fibers containing an asphalt rejuvenator; (c) Evaluate the self-healing efficiency of double-walled microcapsules and hollow-fibers filled with an asphalt rejuvenator, through …

Evaluation And Development Of Cpt Based Pile Design In Nebraska Soils, Alex Silvey

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Cone penetration testing (CPT) is a well established geotechnical subsurface investigation technique commonly used for site characterization and soil classification. The CPT gives real time end resistance, side friction, and pore pressure readings. Axially loaded piles also share these two resistance mechanisms, suggesting the cone can be considered similar to a miniature pile. This study focused on evaluating eight CPT methods prediction of pile bearing capacity. The Nebraska Department of Roads (NDOR) conducts dynamic load tests (PDA) of driven pile to verify pile capacity for bridge foundations. 91 comparisons of CPT logs and PDA data were evaluated. CPT prediction methods …

Utah Salt Storage Facilities Guidelines And Best Management Practices, Weston Bellon

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

An environmental analysis was conducted at the Utah Water Research Laboratory of samples gathered from Utah Department of Transportation (UDOT) salt storage facilities retention ponds across the state. The analysis indicated high levels of TSS largely made up of minerals directly associated with the deicing solution currently used by UDOT in roadway applications. As a companion to that analysis, best management practices have been identified and compiled to provide a resource for the proper management of salt storage facilities in the state of Utah. Topics included as best management practices include locating new storage facilities, proper salt storage, proper salt …

When To Use Midwest Guardrail System (Mgs) W-Beam Guardrail, Katherine Smutzer

Purdue Road School

In this session we will discuss when MGS w-beam guardrail should be placed on state and local projects and review pertinent INDOT Design Memos released over the past year.

Spot-R By Triax, Purdue Ect Team

ECT Fact Sheets Archive

Triax’s Spot-r system was developed to tackle the construction industry’s unique safety and productivity challenges, stemming from a demonstrated lack of total jobsite visibility and automatically collected, easily accessible field data. Spot-r by Triax combines a proprietary mesh network with sensor technology to record and transmit previously unattainable workforce and equipment location, activity and safety data within a defined area – all in real-time.

The Spot-r network is installed around the site and operates in a 900 MHz network, with a subset using a cellular connection to forward Spot-r sensor data to Triax’s custom, cloud dashboard. In the hazardous construction …

Purdue’S Biowall, Purdue Ect Team

ECT Fact Sheets Archive

Mechanical ventilation, energy recovery ventilation, and infiltration (air that leaks into a building) are commonly used to introduce fresh air. These are all valid approaches, but a living plant-based filter is an innovative complement to these traditional technologies. A Biowall has the potential to improve indoor air quality while reducing the quantity of air needed for ventilation, creating the potential for energy savings. Figure 1 shows a Biowall prototype being evaluated in the ReNEWW House, a research home located near the Purdue University campus (http://www.renewwhouse.com/).

Mdp (Machine Drive Power) Intelligent Compaction Technology, Purdue Ect Team

ECT Fact Sheets Archive

Caterpillar developed MDP (Machine Drive Power) technology to fill this gap. Rather than an accelerometer and vibratory drum, it uses the principle of rolling resistance to provide indications of soil stiffness. This allows it to perform more reliably on cohesive and granular soils with less variability than accelerometer systems. It also means that the technology can be used on both vibratory and static drum compactors, which are often used on larger sites. While the technology is quite useful on its own, it is even better as a complementary technology to the existing accelerometer-based systems. Contractors who use vibratory soil compactors …

Risk Management And Practice Alignment For Utility Coordination On Transportation Projects, Roy E. Sturgill Jr.

Theses and Dissertations--Civil Engineering

Utility coordination is an exceedingly complex effort of managing, communicating, and facilitating the avoidance and relocation of utility facilities as needed for highway projects. Utility coordination occurs throughout the design and delivery of a project and best practices are used to make sure this occurs efficiently and in the best interest of the public, who are not only the taxpayers but also the ratepayers. Recent research has attempted to enhance utility location technology and procedures, instill frameworks and tools for utility coordination, and proceduralize risk management relative to utility coordination. However, research attempting to improve various aspects of utility coordination …

Methodology For Load Rating Double-Tee Girder Bridges, Sandip Rimal

Electronic Theses and Dissertations

The most common type of bridge on South Dakota (SD) local roads is precast prestressed double-tee (DT) girders. More than 700 DT bridges are currently in-service in SD. Structural detailing, aging, traffic volume, and environmental conditions affect the structural performance, integrity, and capacity of DT bridges. When a bridge is affected by one or more of the aforementioned parameters, the estimation of the bridge safe live loads is necessary to ensure the safety of the traveling public and to prevent excessive bridge damage and collapse. Load rating of damaged bridges is challenging mainly because of a lack of information regarding …

Advanced Technologies For Efficient Transportation Construction Inspection, Clyde Wesley Newcomer Iv

Theses and Dissertations--Civil Engineering

Collecting load tickets is an example of an antiquated practice that puts inspectors in harm’s way either adjacent to traffic, in close proximity to moving or backing equipment, or at times requires climbing onto trucks to reach tickets. Technology exists to collect this information electronically allowing for safer, efficient inspection methods. Departments of Transportation are charged with inspecting an increasing work load with a diminishing number of inspection staff. Recently, doing more with less has led to the prioritization of inspection activities and resulted in less collection of data and visual inspection on projects. Technology advancements are available to improve …

Tire-Derived Geo-Cylinders And Polymer Products For Enhancing The Properties Of Base/Sub Base Materials In Pavement Systems, Justin Scott Smith

Graduate Theses, Dissertations, and Problem Reports (ETD)

As a critical part of the transportation network, pavements offer a safe means for vehicular traffic. Pavements are subjected to many forms of stress during their service life, and they are susceptible to environment related cracking and failures. Failures can be attributed to poor subgrade, freeze-thaw variations, and fatigue under repetitive axle loadings. Reinforcement products such as tire-derived geo-cylinders (TDGC) which make-up mechanical concrete and geo-polymers have been utilized in civil engineering practice, and this research aims to understand the potential life of tested pavement system components set at displacement limitations when reinforced with TDGCs and geo-polymers from exposure to …

Basic Highway Workzone Safety, Collin Shamberger

Williams Honors College, Honors Research Projects

The purpose of this essay will be to examine, and provide information detailing work zone safety practices, and maximizing safety in construction zones. This report will examine the functionality of components of a work zone and how they work together, the use of standard construction drawings of work zones, personal protective equipment of workers, possible hazards of work zones, minimizing risks and ultimately work zone safety training. Also this report will provide a spreadsheet which can be used to calculate and layout a construction work zone based on a GPS location.

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

College of Graduate Studies: Theses & Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

Manufacturing Applications Of The One-Dimensional Cutting Stock Problem As A Team Project, Hüseyin Sarper, Nebojsa I. Jaksic

Electrical & Computer Engineering Faculty Publications

This paper explains the beneficial and practical impact of operations research in two real manufacturing settings. Two manufacturing examples used in student projects were (1) cutting rails (80‘ or 40‘) to manufacture railroad frogs of many sizes and (2) cutting round metal rolls (12‘ to 20‘) to meet customer demands for various lengths of cuts. Student teams in Engineering of Manufacturing Processes and Operations Research courses wrote computer programs. The program first identified all possible patterns that can be cut out of a given stock length. Next, the program created a mathematical model (a text file) as an output. This …

Datumate, Purdue Ect Team

ECT Fact Sheets Archive

Datumate is digitally transforming civil engineering processes used in construction, surveying and infrastructure inspection markets with fully automated, highly precise, cost effective and safe tools. It utilizes state-of-the-art image processing and advanced drones and camera technologies dramatically reducing the amount of time surveying crews spend in the field, speeding up construction progress checks and shortening infrastructure inspection duration, while maintaining survey grade accuracy. The intuitive, simple and automated solutions increase productivity by saving field and office time in civil engineering and inspection projects of roads, intersections, stockpile volumes, topography, piping, industrial facilities, bridges, property surveys, building facades, railways, cellular infrastructure …

Technology To Manufacture Oriented Pvc (Pvc-O) Pipes, Purdue Ect Team

ECT Fact Sheets Archive

The development of Molecor´s technology, which is based on the application of a Molecular Orientation process, has delivered a significant turning point in the pipelines sector. With this technological development, the company has begun to manufacture TOM® PVC-O pipes, the most eco-friendly pipes on the market. The Molecor technology enabled eradicating many of the existing disadvantages of thermoplastic pipes.

This technology delivers a clear objective; to provide the water industry with a solution for pipes carrying pressurized water in an environmentally friendly, yet cost efficient manner. This also extends a service life compared to pipeline materials currently in use.

The …

Schedule And Cost Performance Analysis And Prediction In Louisiana Dotd, Mahmoud Hamide

LSU New Orleans Theses and Dissertations

Many construction projects in the United States are facing the risk of cost overrun and schedule delays. This is also happening here in the State of Louisiana. When these things happen, it causes cost overrun which can then be passed on to the tax payers and may also cause the state to take on less projects than they normal. Many researchers have studied the reasons behind both the cost overrun and the delays resulting in private firms, developing project management tools and best practices to prevent this risk. In this research, I aim to study the historical trend in 2912 …

Fluid Isolator, Purdue Ect Team

ECT Fact Sheets Archive

The reliability of concrete infrastructure is vital to ensuring daily life, as well as commerce, can progress without interruption. From the pavement of interstate highways to the driveways and sidewalks in a local neighborhood, concrete is expensive to install and often even more expensive, and intrusive, when it needs to be replaced. Unfortunately, to maintain functionality in winter climates concrete is heavily exposed to deicing salts. This not only affects the roads, driveways, and sidewalks where salt is applied directly, but many other areas such as parking and residential garages where vehicles (and people) will track salt along with water …

Netpoint®, Purdue Ect Team

ECT Fact Sheets Archive

The vast majority of construction scheduling software uses a combination of spreadsheets and Gantt charts for developing and depicting Critical Path Method (CPM) schedules. While this paradigm works for the expert scheduler, it is not conducive to collaboration, and it is prohibitively difficult for non-scheduling experts to understand.

NetPoint® provides a dynamic, visual interface conducive to touch and gestural input. Activities are drawn directly on a time-scale and may be placed on the same row or arranged automatically using codes or the WBS. Such control of the presentation makes it easier to communicate the plan to any type of audience. …

A Tool To Evaluate Sustainability Of Pavement Maintenance Projects., Yibo Zhang

Electronic Theses and Dissertations

Pavement maintenance activities are widely regarded to be critical elements during pavement life cycle, different maintenance techniques have been used to restore or extend the service lives of pavements. However, the existing maintenance practices on pavement system have problems that impair the economic benefits, disturb the natural environment, and somewhat ignore the needs from stakeholders. To minimize these negative impacts, sustainability is an ideal way because it addresses the problems under Triple Bottom Line (TBL, refers to economy, environment, and society). Sustainability analysis within transportation or pavement industry has been studied in different countries, but the concept of sustainable pavement …

Smartvid.Io, Purdue Ect Team

ECT Fact Sheets Archive

The collection, organization, and retrieval of industrial media is a pervasive challenge that is especially glaring for companies in the AEC industry. Construction projects often generate large volumes of pictures & videos from the field for tracking progress and communicating between engineers, contractors, and subcontractors. It is not uncommon for field personnel to capture hundreds of photos per week on any given jobsite.

Smartvid.io is a cloud-based software solution designed for the specific needs of industrial media. The application’s internal deep-learning engines, collectively nicknamed VINNIE (for ‘Very Intelligent Neural Network for Insight and Evaluation’), use speech and image recognition to …

Hillman Composite Beam (Hcb®), Purdue Ect Team

ECT Fact Sheets Archive

The Hillman-Composite Beam (HCB®), is an innovative structural member for use in highway and railroad bridges as well as marine facilities. The HCB is essentially a lightweight reinforced concrete beam strengthened and protected by a corrosion-resistant and resilient Fiberglass Reinforced Polymer (FRP) shell.

The beam is comprised of three main components, a concrete arch (compression reinforcement), an FRP bottom flange encapsulating steel strands tying the ends of the arch together (tension reinforcement) and the FRP shell. Galvanized Rebar “shear connectors” are used to make the beam composite with the concrete deck in the same manner as pre-stressed concrete beams.

The …

Industrial-Grade Monitoring Solution: Hoistcam, Purdue Ect Team

ECT Fact Sheets Archive

Safety and productivity are top priorities for contractors and industrial operations. Improving either makes a company more profitable and competitive. Technology advancements that can do both are important for every company to consider. HoistCam^TM industrial-grade video monitoring solutions can improve employees’ productivity and workplace safety in the construction industries. HoistCam also improves efficiency of operations and reduces job site accidents resulting in substantial cost savings to a contractor.

HoistCam™ is an integrated, wireless video system. The use of HoistCam eliminates blind lifts, blind spots and can share the live video with anyone, anywhere with solid security and easy control. …

Optimizing Steel Railway Truss Bridge Health Monitoring, Ahmed Rageh, Daniel Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Problems - Steel Railway Trusses • Aging • Large system – bridge AND railway • Labor intensive condition eval • Reported conditions: Stringer-to-floor beam connections [Haghani 2012] Stringer flange clip angle cracks [Haghani 2012] Unequal eyebars stress distribution [DelGrego 2008] Displaced eyebar pins [DelGrego 2008

Problems – Condition Evaluation • Visual inspection: Prescribed frequency Costly Subjected to human interpretation • Sensors: Focused on a single bridge Extensive array Costly

Influence Of Skew And Nonlinear Deck On Elastic Versus Inelastic Distribution Behavior And Ultimate Capacity Of Steel Girder Bridges, Fayaz Sofi, Joshua Steelman

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Research Objectives

• Assessment of alternative load distribution methodologies for potential discrepancies that arise when evaluating distribution behavior of skewed steel girder bridges.

• Investigate the influence of skew and material nonlinearities (concrete cracking and steel yielding) on

• Load distribution behavior (elastic versus inelastic).

• System capacities (yielding and ultimate).

Summary and Conclusions • Influence of skew was examined on load distribution behavior, and nonlinear system-based capacities (yielding and ultimate) of composite steel girder bridges in presence of full material nonlinearities. In addition, assessment of two general definitions (beam-line and response fraction approaches) for quantifying load distribution behavior was …