Construction Engineering and Management Commons^™

Application Of Computational Tools To Spaghetti-Based Truss Bridge Design, Jin Xu, Jiliang Li, Nuri Zeytinoglu, Jinyuan Zhai

ASEE IL-IN Section Conference

Application of Computational Tools to Spaghetti-Based Truss Design

Statics and Strength of Materials are two foundational courses for Mechanical/Civil Engineering. In order to assist students in better understanding and applying concepts to a meaningful design task, SolidWorks and theoretical calculation were used for a spaghetti-bridge design contest with the constraints of given maximum weight and allowable support-material weight. As the first step of this iterative designing process, both extrude feature and structural member were introduced to model planar bridge trusses. Then SolidWorks’ Statics module was used to run FEA analysis of the structural performance in efforts to optimize the …

Optimal Placement Of Distributed Energy Storage Systems In Distribution Networks Using Artificial Bee Colony Algorithm, Choton K. Das, Octavian Bass, Ganesh Kothapalli, Thair S. Mahmoud, Daryoush Habibi

Research outputs 2014 to 2021

The deployment of utility-scale energy storage systems (ESSs) can be a significant avenue for improving the performance of distribution networks. An optimally placed ESS can reduce power losses and line loading, mitigate peak network demand, improve voltage profile, and in some cases contribute to the network fault level diagnosis. This paper proposes a strategy for optimal placement of distributed ESSs in distribution networks to minimize voltage deviation, line loading, and power losses. The optimal placement of distributed ESSs is investigated in a medium voltage IEEE-33 bus distribution system, which is influenced by a high penetration of renewable (solar and wind) …

Toward Building Resilient, Sustainable, And Smart Infrastructure In The 21st Century, Aly Mousaad Aly

Faculty Publications

In recent years, as a result of significant climate change, stringent windstorms are becoming more frequent than before. Given the threat that windstorms bring to people and property, wind/structural engineering research is imperative to improve the resilience of existing and new infrastructure, for community safety and assets protection. The Windstorm Impact, Science and Engineering (WISE) research program at Louisiana State University (LSU) focuses on creating new knowledge applicable to the mitigation of existing and new infrastructure, to survive and perform optimally under natural hazards. To achieve our research goals, we address two imperious challenges: (i) characterization of realistic wind forces …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …

My Catalyst, Gabrielle Gambino Lyon

Celebration of Learning

Over the course of my internship and shadow program with Pepper Lawson Construction and Ziegler Cooper Architects, I was able to explore the various career paths involved in the design, construction, and civil engineering fields. My work on the construction site of a high-rise apartment building located in the heart of Houston, TX allowed me first-hand experience working and learning alongside project engineers, contractors, building developers, and the construction team.

This project was the perfect confluence of my main areas of interest: structural, mechanical, civil, and environmental engineering, as well as architecture. My daily work consisted of on-site walk throughs, …

Effects Of Tension On Resonant Frequencies Of Strings, Blake Burnett

Senior Theses

This project tests and explores resonance of strings. Since all materials and mechanisms are affected by vibrations, it is important to know the frequencies at which resonance occurs. To explore this subject, strings were used as a model material to test the effect tension has on resonance. The fundamental frequencies and the corresponding modes of resonance were used to analyze the data. The results of this experiment show that increasing tension on a string increases its resonance frequency. Understanding the physics behind resonance frequency allows systems to be designed to take advantage of resonance properties, or to avoid resonance where …

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

College of Graduate Studies: Theses & Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

The Subject Librarian Newsletter, Engineering And Computer Science, Fall 2017, Buenaventura "Ven" Basco

Libraries' Newsletters

No abstract provided.

On The Ramberg-Osgood Stress-Strain Model And Large Deformations Of Cantilever Beams, Ronald J. Giardina Jr

LSU New Orleans Theses and Dissertations

In this thesis the Ramberg-Osgood nonlinear model for describing the behavior of many different materials is investigated. A brief overview of the model as it is currently used in the literature is undertaken and several misunderstandings and possible pitfalls in its application is pointed out, especially as it pertains to more recent approaches to finding solutions involving the model. There is an investigation of the displacement of a cantilever beam under a combined loading consisting of a distributed load across the entire length of the beam and a point load at its end and new solutions to this problem are …

Audio-Based Productivity Forecasting Of Construction Cyclic Activities, Chris A. Sabillon

College of Graduate Studies: Theses & Dissertations

Due to its high cost, project managers must be able to monitor the performance of construction heavy equipment promptly. This cannot be achieved through traditional management techniques, which are based on direct observation or on estimations from historical data. Some manufacturers have started to integrate their proprietary technologies, but construction contractors are unlikely to have a fleet of entirely new and single manufacturer equipment for this to represent a solution. Third party automated approaches include the use of active sensors such as accelerometers and gyroscopes, passive technologies such as computer vision and image processing, and audio signal processing. Hitherto, most …

Modeling Atypical Building Use With Commercially Available Building Simulation Software, Sarah E. Schanck

Theses and Dissertations

National Guard armories are audited to provide recommendations for future energy reduction measures. The annual energy consumption of a New Jersey National Guard Armories cannot be modeled directly with commercially available building simulation software, due to discrepancies between the modeling capabilities of the software and the reality of the armory. A building simulation software, eQUEST, was chosen for use in this project. Discrepancies between eQUEST inputs and reality were identified and correction factors developed to minimize the effect of each discrepancy on predicted energy consumption, with the end goal of accuracy between predicted and actual energy consumption. In addition, an …

Computing Research In Academia: Classifications, Keywords, Perceptions, And Connections, Sung Han Kim

Theses and Dissertations

The Association for Computing Machinery (ACM) recognizes five computing disciplines: Computer Science (CS), Computer Engineering (CE), Information Technology (IT), Information Systems (IS), and Software Engineering (SE). Founded in 1947 the ACM is the world's largest society for computing educators, researchers, and professionals. While Computer Science has been a degree program since 1962, the other four are relatively new. This research focuses on understanding the graduate research in four of the five ACM disciplines (CS, CE, IT, and IS) using a large body of thesis and dissertation metadata. SE is not found in the metadata and graduate work in SE is …

Enhancing Project Management With Lean World Class Manufacturing In Construction, Jacob Randles

College of Graduate Studies: Theses & Dissertations

In construction, the goal of commercial projects is to turn a profit. This is achieved by minimizing inputs and maximizing outputs while building a product that meets the customer’s perception of value. Value is determined through pre-negotiated specifications, plans, and material quality. Even in U.S. military construction, the unit executing the construction wants to complete the task on time and on budget, which can be difficult to do. Studies on project completion showcase a surprisingly high rate of failure in reaching the aforementioned “on time, on budget” goal. It is important to understand the nuances and details of U.S. Army …

Color Removal From Pulp Mill Effluent Using Coal Ash Produced From Georgia Power Coal Combustion Plants, Christopher B. Willett

College of Graduate Studies: Theses & Dissertations

Two environmental concerns currently face Georgia: coal fly ash (CFA) waste from coal power plants, and the effluent generated by pulp mills. Pulp mill effluent discolors surface waters into which it is discharged, and has been proven to negatively impact the dissolved oxygen and carbon necessary for aquatic life. The proposed solution is a cost-effective adsorption treatment using an inexpensive but abundantly available waste material: CFA. CFA possesses beneficial properties that allow it to effectively remove contaminants, and is available at significantly reduced cost. The primary research objective was to define treatment parameters that would result in the maximum removal …

A Comparative Analysis Of Energy Modelingmethods For Commercial Buildings, Spencer Mark Salmon

Theses and Dissertations

This thesis researched the accuracy of measured energy data in comparison to estimated hand calculation data and estimated building energy performance simulation data. In the facility management industry, there is minimal evidence that building energy performance software is being used as a benchmark against measured energy usage within a building. Research was conducted to find examples of measured energy data compared to simulated data. The study examined the accuracy of a simulation software and hand calculations to measured energy data. Data suggests that comparisons may be made between building energy performance simulated data and measured data, though comparisons are solely …

Vulnerability Of Progressive Collapse In Reinforced Concrete Flat-Plate Buildings, Jinrong Liu

College of Engineering: Graduate Celebration Programs

• Progressive collapse is the spread of initial local failure, causing partial or
  even total collapse of a building.
• Flat plate structure is widely used for office and residential buildings.
• There is a large inventory of older flat plate building without continuous slab bottom reinforcement through columns.
• Limited knowledge exists regarding the risk of disproportionate collapse in
  older flat-plates under sudden column removal during abnormal events.
• Reliable mechanical model is needed for structural evaluation.

Starch Resin Moisture Level Effect On Injection Molding Processability And Molded Part Mechanical Properties With Pure Starch Resin And Polymer Blends, Jordan M. Ellingson

Theses and Dissertations

The current and forecasted global consumption of plastic packaging and products through the 21st century combined with the already reported and growing negative impact of plastics on the environment due to plastics being synthesized from nonrenewable resources that do not biodegrade is of serious concern. However, recent advances in starch technology including the development of thermoplastic starch (TPS) materials —polymers that are both renewable and biodegradable—have brought hope to reducing this impact. The mechanical properties of thermoplastic starch have often been improved by blending with synthetic polymers. One issue that arises with blending is volatilization of the melt from moisture …

Location-Allocation Optimization Of Supply Chain Distribution Networks: A Case Study, Mark Nicholas Helberg

Theses and Dissertations

The location of distribution centers is an important strategic decision in supply chain design, particularly as it relates to service quality, productivity, and profitability of the firm. There has been extensive research performed on distribution location models which require the use of complex algorithms and assumptions that make use of these models difficult in practice for small and medium enterprises (SMEs) that have limited capital and resources. Studies have also failed to capture and quantify potential business results of using more sophisticated methods. In this study, a deterministic and static location-allocation model is designed using a prototype software tool. The …

Best Practices Using Building Information Modeling In Commercial Construction, Simon Beveridge

Theses and Dissertations

There has been an increase in adoption of building information modeling (BIM) by commercial contractors over the past few years but there is not a clear indication of current application or the frequency of each use. This research was undertaken to determine the frequency and best practices of using BIM in commercial construction. Leading commercial contracting firms were contacted and employees were selected to complete a telephone survey that was designed to determine how they are using BIM. It was found that BIM is being used with more frequency on projects, with plans to continue to implement it even further …

A Comparative Study Of Strength And Stiffness Of Thin-Walled Specimens Fabricated By Fdm And 3d Printing Technologies, Miranda Rodrigo

Theses and Dissertations

Rapid Prototyped part failure constitutes a major issue for both RP providers and customers. When parts fail the reputation of the vendor is heavily deteriorated, customer dissatisfaction increase and replacement of the broken parts is often necessary to avoid the loss of future business. Product design teams often run into situations where Rapid Prototyped parts are not able to withstand shipping and handling and delivered broken or while demonstrating and examining the parts. When done in the face of customers this builds a perception of poor quality and lack of aptitude on the design group as well as the RP …

Combined Heat, Air Moisture And Pollutant Simulations (Champs) For Buildings, Jianshun Zhang, Menghao Qin

Mechanical and Aerospace Engineering - All Scholarship

No abstract provided.

Seamless Bridge And Roadway System For The U.S. Practice, Nima Ala

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Expansion joints are one of the main causes for high maintenance costs in bridges. The search for ideal expansion joints has proven fruitless. That is why it has been said that “the best joint is no joint”. A seamless bridge system is envisioned that results in bridges with long service lives by eliminating the joints over the entire length of the bridge, approach slab and a segment of the roadway called transition. All bridge thermal movements are dissipated to zero in the transition. The system is similar to a system developed in Australia but modifications had to be made to …

Performance Analysis Of Solar Walls In Minnesota: Final Project Report, Patrick A. Tebbe, Saeed Moaveni, Louis Schwartzkopf

Mechanical and Civil Engineering Department Publications

A study of unglazed transpired solar collectors (referred to as solar walls for this report), has been undertaken. Several installations in the Twin Cities, MN region have been identified, researched, and studied. A combination of weather stations, data logging systems, and building energy management systems were used to collect experimental data on four buildings. Performance calculations were then performed for these buildings and compared with various performance/modeling tools.

How Much Do U.S. University Students Know, And Want To Know, About Sustainability And Green Building? The Findings Of A Survey, And Possible Implications For General Elective Curricula., Jeremy R. Farner

Purdue Polytechnic Masters Theses

Using the survey approach, this investigation examined the attitudes and interest of college students at two universities in different geographic locations within the United States.  Approximately 24,000 students from all disciplines and majors at Weber State University (WSU) in Utah, and 4,000 at Purdue University in Indiana, were invited to participate in a study to determine current knowledge, familiarity, and interest in topics within the sustainability and Green Building educational arena. The goal of this study was to determine what students already know, would like to know, and how much interest there would be in developing …

A Study Of The Cause Of Failure Of Rotationally Molded, High-Density Polyethylene, Sodium Hypochlorite Storage Tanks, Dixon Harold Abell

Theses and Dissertations

The topic of chemical oxidative degradation in rotational molded polyethylene (high-density cross-linked) chemical (sodium hypochlorite) storage tanks is an industry problem that ranks at the top of current business issues for manufacturers of chemical storage tanks. The degradation of these tanks not only compromises the physical and mechanical properties of the tank material, but reduces the life expectancy of the tank, eventually resulting in catastrophic tank failure. Premature tank failure comes at a hefty cost. The reputation of the manufacturer is questioned often resulting in immediate loss of customer satisfaction and future business. The leaking of the chemical from the …

Design Of A Smart System For Monitoring Concrete Curing And Structural Health, William Quinn

Theses

Structural Health Monitoring (SHM) is a rapidly growing sector of the construction industry. Automated monitoring methods arc mainly limited to global monitoring and the application of local monitoring methods has not gained widespread application due to the fact that currently technology requires that the systems are wired to data acquisition devices. This thesis presents a fully embeddable wireless sensor node for the local monitoring of structural concrete. It presents the first reported wireless embedded system implementation of the electromechanical impedance method using both resonant and antiresonant sensors for this purpose.

The first section of this thesis examines the feasibility of …

An Experimental Investigation Of Friction Bit Joining In Az31 Magnesium And Advanced High-Strength Automotive Sheet Steel, Rebecca Gardner

Theses and Dissertations

Friction Bit Joining (FBJ) is a recently developed spot joining technology capable of joining dissimilar metals. A consumable bit cuts through the upper layer of metal to be joined, then friction welds to the lower layer. The bit then snaps off, leaving a flange. This research focuses on FBJ using DP980 or DP590 steel as the lower layer, AZ31 magnesium alloy as the top layer, and 4140 or 4130 steel as the bit material. In order to determine optimal settings for the magnesium/steel joints, experimentation was performed using a purpose-built computer controlled welding machine, varying factors such as rotational speeds, …

Natural Fibers And Fiberglass: A Technical And Economic Comparison, Justin Andrew Zsiros

Theses and Dissertations

Natural fibers have received attention in recent years because of their minimal environmental impact, reasonably good properties, and low cost. There is a wide variety of natural fibers suitable for composite applications, the most common of which is flax. Flax has advantages in tensile strength, light weight, and low cost over other natural fibers. As with other natural and synthetic fibers, flax is used to reinforce both thermoset and thermoplastic matrices. When flax is used in thermoplastic matrices, polypropylene and polyethylene are the main resins used. Although at first glance flax may seem to be a cheaper alternative to fiberglass, …

Investigation Of Rf Curing Parameters In Resin Infusion Molding, Christopher K. Love

Theses and Dissertations

The purpose of this study is to investigate RF or Radio Frequency energy as a viable alternative to traditional heating methods for the purpose of curing resins used in resin infusion molding, a molding system for polymeric composites. Traditional heating/curing methods include technologies such as room temperature, oven, microwave, infrared, and ultraviolet. Although RF curing provides far more advantages than disadvantages, its implementation into a manufacturing process can be challenging. Specifically, three critical elements must be present in order for RF to function in a manner that is profitable to the manufacturer. Those elements are: (1) the proper generator (voltage …

Development Of A Particle Flow Test For Rotational Molding, Russell B. Whatcott

Theses and Dissertations

One of the current testing method (the Dry Flow test) to qualify resin for use in production in the rotomolding process has been shown to have many flaws in both equipment and procedure. Research was done here to investigate a possible alternative that could eliminate some of these testing deficiencies. By reducing equipment and operator errors, the testing of materials becomes more valuable of an exercise. The Angular Flow test developed in this research can increase repeatability. By coming to understand the rotational molding process better, an evaluation that can give more valid information was devised.