Construction Engineering and Management Commons^™

An Analysis Of The Effectiveness Of Bitumen Additives On The Performance Of Pavement Surface Dressings, Alan Anderson, John Casserly, Alan Kavanagh, Jim Campbell

Civil Engineering Research in Ireland 2020

Surface dressing is a maintenance technique that uses thin layers of bitumen emulsion and single sized aggregates. The surface dressing process seals and binds the surface of a road to protect its substructure from water ingress. It also provides increased skid resistance, which improves safety for road users. Early life chip-loss can occur if there is an insufficient degree of adhesion between the emulsion and aggregate used. The range of additives used in bitumen can have an effect on their adhesion properties. The focus of this research project was to investigate if the use of these additives in surface dressing …

An Experimental Investigation Of The Optimum Properties And Conditions For Use Of Anionic Emulsions In Road Maintenance Applications, Simonas Ignatavicius, Alan Kavanagh, David Colleran, Michael J. Brennan, Shane Newell

Civil Engineering Research in Ireland 2020

Bitumen emulsions are used for a range of road maintenance applications, including surface dressing, gravel seals, slurry seals, tack coating, cold-mix asphalt and in situ pavement recycling. The emulsions used can be classified as being either cationic (i.e. possessing a positive electrostatic surface charge) or anionic (i.e. carrying a negative electrostatic surface charge). The vast majority of emulsions used for such applications in Europe are cationic, while anionic bitumen emulsions are used widely throughout North America and Africa. The aims of the experimental study described in this paper were (a) to investigate why one or the other emulsion type is …

Analysis And Optimisation Of Tii’S Pams Reset Values And Deterioration Models For Irish Pavement Conditions, James Quinn, Raymond Mcgowan, Tomas O'Flaherty

Civil Engineering Research in Ireland 2020

Ireland has a national road network of approximately 5300km that is managed by Transport Infrastructure Ireland (TII). TII create yearly pavement maintenance and renewal programs from the operation of a Pavement Asset Management System (PAMS). Accurate pavement deterioration models and reset values are an essential part of PAMS and are required for life cycle cost analysis (LCCA). Pavement maintenance and renewal schemes are prioritised based on the LCCA's largest benefit to cost ratio, and therefore optimise the annual pavement maintenance and renewal budget. Currently, TII implement pavement deterioration models and reset values from Austria's and Belgium's PAMS, and are not …

An Analysis Of The Effectiveness Of Bitumen Additives On The Performance Of Pavement Surface Dressings, Alan Anderson, John Casserly, Alan Kavanagh, Jim Campbell

Civil Engineering Research in Ireland 2020

Surface dressing is a maintenance technique that uses thin layers of bitumen emulsion and single sized aggregates. The surface dressing process seals and binds the surface of a road to protect its substructure from water ingress. It also provides increased skid resistance, which improves safety for road users. Early life chip-loss can occur if there is an insufficient degree of adhesion between the emulsion and aggregate used. The range of additives used in bitumen can have an effect on their adhesion properties. The focus of this research project was to investigate if the use of these additives in surface dressing …

Towards Automated Uav Assisted Bridge Inspections Using Photogrammetry And Image Processing Techniques, Habeene Habeenzu, Patrick Mcgetrick, David Hester, Su Taylor, Louie Wong

Civil Engineering Research in Ireland 2020

At the heart of addressing bridge condition challenges are bridge inspections. The main activity during a bridge inspection is close, arm’s length visual inspection of the entire bridge structure. During this process, all defects such as cracks, spalls and material degradation are manually recorded on the bridge itself and on inspection forms. Where access is difficult such as where a safe working platform cannot be mounted under bridge decks, or on high bridges, expensive underbridge equipment is required which when used results in expensive lane closures. Furthermore, visual inspections have been shown to lack consistency from inspector to inspector and …

Acceleration Based Bridge Weigh In Motion Using Moving Force, Shou Wang, Daniel Mccrum, Eugene O'Brien

Civil Engineering Research in Ireland 2020

Measuring vehicle axles weights is an important method to control traffic and monitor infrastructure. Traditional methods of measuring the static weight of vehicles at a weigh station is disruptive and time consuming. It is more cost effective and efficient to indirectly measure moving vehicle weights crossing a bridge. The weigh-in-motion concept, first proposed by Moses (1979) is an algorithm that uses measured bridge structural response (deflection, strain, …) due to passing vehicles to and a theoretical response. Moving Force identification (MFI) is a variation of the dynamic WIM algorithm that gives a force time history as a vehicle passes the …

Wind Power Prediction And Early Downtime Detection For Ireland, Vikram Pakrashi, Basuraj Bhowmik, Juan Manuel González-Sopeña, Paul Mucchielli, Bidisha Ghosh

Civil Engineering Research in Ireland 2020

Wind energy must be commercially competitive to be economically sustainable. Existing wind farms in Ireland must be more efficient to meet the 2009 EU Renewable Energy Directive target of 7% of total energy demand from onshore wind energy farms, which is 45% of the total national renewable energy target of 16%. WindPearl - a Sustainable EnergyAuthority of Ireland (SEAI) funded project is currently looking into improvin operations & maintenance (O&M) of onshore wind turbine farms in Ireland.

Application Of The Iec Technical Specification For Assessment Of Wave Energy Resource: A Case Study From The West Coast Of Ireland, Iulia Anton, Stephen Nash

Civil Engineering Research in Ireland 2020

There is significant interest globally in harnessing our ocean wave energy resource, estimated at approximately 30,000 TWh/year. The key to this is understanding the resource. The International Electrotechnical Commission (IEC) has developed a technical specification for the evaluation of wave energy resource, IEC-TS 62600- 101: Wave energy resource assessment and characterization. This research applies the IEC standard for a resource characterization study of the Atlantic Marine Energy Test Site on the west coast of Ireland. A key focus is the comparison of the detailed IEC validation approach using scatter diagrams with the traditional timeseries validation approach. Coarse (0.005°) and fine …

A Review Of Vision Based Methods For Pothole Detection And Road Profile Analysis, Darragh Lydon, Su Taylor, Myra Lydon, Julia Early

Civil Engineering Research in Ireland 2020

This paper is an overview of the development and application of Computer Vision for the detection of pothole, pavement distress and road profile analysis and categorisation. A brief explanation of the traditional methods for determining these factors is given, followed by a chronological description of the evolution and the challenges of using Computer Vision (CV) approaches to determine these conditions. The paper is separated into sections aligned to image capture and analysis methodologies. Qualitative evaluations and comparison of these methods have been provided along with the proposal of guidelines for new computer vision-based road analysis systems.

Analysis And Optimisation Of Tii’S Pams Reset Values And Deterioration Models For Irish Pavement Conditions, James Quinn, Raymond Mcgowan, Tomas O'Flaherty

Civil Engineering Research in Ireland 2020

Ireland has a national road network of approximately 5300km that is managed by Transport Infrastructure Ireland (TII). TII create yearly pavement maintenance and renewal programs from the operation of a Pavement Asset Management System (PAMS). Accurate pavement deterioration models and reset values are an essential part of PAMS and are required for life cycle cost analysis (LCCA). Pavement maintenance and renewal schemes are prioritised based on the LCCA's largest benefit to cost ratio, and therefore optimise the annual pavement maintenance and renewal budget. Currently, TII implement pavement deterioration models and reset values from Austria's and Belgium's PAMS, and are not …

Winter Maintenance On The Irish Road Network, Hugh Mcconnell, Brian Mccann

Civil Engineering Research in Ireland 2020

Winter maintenance relates to those activities undertaken where the objective is to minimise the impact of frost, ice or snow on the travelling public. The responsibility for winter maintenance of all roads in Ireland currently rests with local authorities and Transport Infrastructure Ireland (TII) (Formerly the NRA) on behalf of the Department of Transport, Tourism and Sport (DTTaS), (DTTaS, 2017). The aim of the study was to examine current winter maintenance practices undertaken in Ireland by local authorities and the Motorway Maintenance and Renewals Contracts (MMaRC) contractors and examine the potential financial, operational and environmental benefits if pre-wet and brine …

A Review Of Vision Based Methods For Pothole Detection And Road Profile Analysis, Darragh Lydon, S. E. Taylor, Myra Lydon, Julia Early

Civil Engineering Research in Ireland 2020

This paper is an overview of the development and application of Computer Vision for the detection of pothole, pavement distress and road profile analysis and categorisation. A brief explanation of the traditional methods for determining these factors is given, followed by a chronological description of the evolution and the challenges of using Computer Vision (CV) approaches to determine these conditions. The paper is separated into sections aligned to image capture and analysis methodologies. Qualitative evaluations and comparison of these methods have been provided along with the proposal of guidelines for new computer vision-based road analysis systems.

Winter Maintenance On The Irish Road Network, Hugh Mcconnell, Brian Mccann

Civil Engineering Research in Ireland 2020

Winter maintenance relates to those activities undertaken where the objective is to minimise the impact of frost, ice or snow on the travelling public. The responsibility for winter maintenance of all roads in Ireland currently rests with local authorities and Transport Infrastructure Ireland (TII) (Formerly the NRA) on behalf of the Department of Transport, Tourism and Sport (DTTaS), (DTTaS, 2017). The aim of the study was to examine current winter maintenance practices undertaken in Ireland by local authorities and the Motorway Maintenance and Renewals Contracts (MMaRC) contractors and examine the potential financial, operational and environmental benefits if pre-wet and brine …

Modelling The Thermal Behaviour Of A Precast Pcm Enhanced Concrete Cladding Panel, Dervilla Niall, Roger P. West, Oliver Kinnane, Richard Hegarty

Civil Engineering Research in Ireland 2020

According to the World Business Council for Sustainable Development there is currently a stock of more than 80 million buildings in Europe built between 1950 and 1975, a period during which energy performance was not considered in building design. To enable governments to comply with the European Directive 2010/31/EU on the energy performance of buildings, strategies are required to improve the energy efficiency of these buildings. Using the mass of a building to store or dissipate heat can reduce the demand on the auxiliary heating and/or cooling systems and hence reduce the overall energy demand of the building.

Previous research …

Analysis And Design Of A Novel Heavy-Duty Precast Element, Daniel Naughton, Michael Naughton, Michael O'Sullivan, Suhaib Salawdeh

Civil Engineering Research in Ireland 2020

Window sills are common to most buildings. In Ireland, concrete is the most popular material used for external sills. A standard one-metre concrete window sill weighs about 70kg. While external window sills are required to have sufficient capacity to resist damage during transportation and loading, they are non-structural elements. Therefore, there is no need for their high selfweight. This project looks to redesign concrete window sills to make them lighter. Decreasing the amount of concrete used in each sill would significantly reduce their self-weight. This would make concrete window sills more manageable in terms of transportation and installation. Two design …

Development And Localisation Of Ultra High Performance Concrete Using A Particle Packing Model, William Wilson, Tomas O'Flaherty

Civil Engineering Research in Ireland 2020

Ultra-high performance fibre reinforced concrete (UHPFRC) is used worldwide to improve the structural performance of infrastructure such as bridges, extend their working life and reduce environmental impact. As a result thinner structures are constructed leading to reductions in the structure’s self-weight and the volume of concrete and natural raw aggregates used in their construction. A drawback to UHPFRC is that it results in a significant rise in initial costs over normal and even high performance concretes, and it has very high binder contents, which in some cases is greater than 1100kg/m³. Therefore, the cost-efficiency and sustainability of this …

Composite Behaviour Of Wide Sandwich Panels With High Performance Concrete Thin Wythes With And Without Thermomass Shear Connectors, Jagoda Lipczynska, Roger P. West, Michael Grimes, Dervilla Niall, Oliver Kinnane, Richard Hegarty

Civil Engineering Research in Ireland 2020

To partly address the future sustainability of energy use in buildings, there is a program in Europe to retrofit domestic and commercial buildings with non-load bearing insulated re-cladding and over-cladding panels. Recent research work has shown that limited composite action is possible depending on the type of non-conductive shear connector and the stiffness of the insulation between the inner and outer wythes. This paper reports on the mix design development to develop high strength 20mm thick wythes and the manufacture of sandwich panels with five silicone-bonded layers of XPS insulation, making up a panel which is 220mm thick. These model …

Study The Effect Of Damping Change During The Dynamic Analysis Of A Reinforced Concrete Bridge With Neoprene Cushions, Mais Ghassoun

Emirates Journal for Engineering Research

The damping ratio has a important effect on the dynamic behavior of the bridges. and it is customary when designing to assume it as a predetermined fixed value independent of the response amplitude and frequency of the structure . A lot of experimental research worked on identifying them, but the dependence of damping and other dynamic characteristics of vibration amplitudes and their impact on responses and the results of the analysis need more scrutiny and simulation due to the difficulty of conducting vibration experiments for structures of realistic dimensions and large weights such as a RC bridge, which necessitated a …

Performance Testing Of Hot Mix Asphalt Containing Biochar, Shadi Saadeh, Yazan Al-Zubi, Basel Zaatarah

Mineta Transportation Institute

In recent years, researchers have been able to identify asphalt binder additives, such as polymers and bio-binder, that can enhance the rheological and mechanical properties of asphalt binders. Earlier studies show that utilizing bio-binder as a partial replacement for asphalt binder has shown promising results in both mechanical and sustainability aspects. Biochar additions improved binder viscosity and low-temperature characteristics. Biochar, which is a byproduct of producing bio-binder, has shown enhanced rheological and mechanical properties when used as an additive to the asphalt binder. In this study, the mechanical properties of asphalt mixtures containing Biochar were investigated. In addition, its color …

Examining The Effects Of Reducing The Cement Content Of Portland Cement Concrete Pavement, Bryan Casillas

Graduate Theses and Dissertations

Portland cement is a significant component in a concrete mixture. For concrete used in portland cement concrete pavement (PCCP), the Arkansas Department of Transportation (ARDOT) specifies a minimum cementitious material content of 564 lb/yd3 and a maximum water-cementitious material ratio of 0.45. Prior research conducted at the University of Arkansas, TRC 0603, indicated concrete mixtures used in five bridge decks throughout Arkansas achieved the required 28-day strength at seven days, and the measured compressive strength at 28 days was 30% greater than required. The use of high strength concrete in pavements throughout the state can increase cracking and consequently reduce …

Quantifying Workability, Compactability, And Cohesion Gain Of Asphalt Emulsion Cold In-Place Recycling, Sadie Casillas

Graduate Theses and Dissertations

To maximize the life and quality of a pavement, proper maintenance and rehabilitation are essential. Strategies for pavement rehabilitation with many sustainable benefits are pavement recycling. This dissertation focuses on two types of in-situ pavement recycling: Cold in-place recycling (CIR) stabilized with asphalt emulsion and full depth reclamation (FDR) stabilized with asphalt emulsion or foamed asphalt. One white paper (Chapter 2), two accepted peer reviewed journal articles (Chapters 3 and 4), and one submitted peer reviewed journal article (Chapter 5) are presented in this document to create better understanding of the unique material characterization of asphalt emulsion cold recycled materials, …

Verifying The Calcium Oxychloride Threshold In Cementitious Pastes, Fatoumata Traore

Graduate Theses and Dissertations

Calcium oxychloride (CAOXY) formation is a serious deterioration mechanism known to cause joint damage in concrete pavements. CAOXY is the product of a chemical reaction between calcium chloride (CaCl2) or magnesium chloride (MgCl) deicing salts and calcium hydroxide in the cementitious matrix. Currently, the accepted CAOXY threshold at which deterioration is mitigated in cementitious paste is 15 g/100 g paste (15 oz/100 oz paste); however, this limit was developed using flexural strength testing. For this investigation, the current threshold was evaluated using compressive strength and mass change over time in paste specimens exposed to CaCl2. Fly ash is used to …

Case Study: Diesel-Powered Loaders Compared To Hybrid Loaders In Heavy Civil Construction, Jesus O. Pena

Construction Management

With the construction industry constantly changing, the environmental impacts of greenhouses gases have become a huge concern. Many contractors are adapting and switching over to hybrid powered systems to allow for more energy saving methods for heavy equipment, an increase in productivity, and efficient construction equipment that comply with emission regulations. The goal for this paper is to analyze the feasibility of heavy civil construction companies switching over from conventional diesel-powered wheel loaders to hybrid wheel loaders. Due to the competitive and saturated market in roadwork construction, many contractors have already begun to invest into hybrid systems. This provides cost …

Bs News July/August

Building Services Engineering

No abstract provided.

Enhancing Facility Management For Existing Facilities With Building Information Modeling, Ryan Loeh

Theses and Dissertations

Building information modeling (BIM) refers to the process of creating a comprehensive three-dimensional (3D) model that allows for a seamless transition from design and construction to operation & maintenance during a building's lifecycle. While a majority of past research for building information modelling was focused on design and construction, research has shifted to operation, maintenance and renovation. This study investigates the feasibility of integrating BIM (Autodesk Revit) and facility management (BUILDER SMS). BUILDER SMS is currently used at the sponsor's facilities to encourage proactive maintenance and provide updated condition assessments. While both datasets have their own benefits, this study investigates …

On The Seismic Performance Of Skewed Special Moment Frame Reduced Beam Section Connections, Damaso Daniel Dominguez

Graduate Theses and Dissertations

Special Moment Frames (SMFs) are frequently used in high seismic areas for architecturally constrained designs, as they provide lateral system stiffness without the use of braces which often obstruct views and architectural features. Reduced beam section (RBS) connections are popular SMF connection details developed following the Northridge earthquake to limit brittle fractures within connection welds. Current American Institute of Steel Construction (ASIC) provisions (i.e. AISC 341-16) provide prequalified SMF RBS connection details (including welding requirements); however, all prequalified details only consider orthogonal connections between the beam and column. This dissertation investigates the effect of adding skew within SMF RBS connections …

Numerically Modeling Steel Continuous Bridges For Early Age Concrete Deck Cracking, Abdul Aziz Nabil Salah

Graduate Theses and Dissertations

Early age bridge deck cracking is a common problem throughout the United States. Early age cracking develops shortly after the deck is poured. It reduces the serviceability and lifespan of bridges. Early age cracking can be typically attributed to either of two factors, 1) construction practices, and 2) shrinkage. The Arkansas Department of Transportation (ARDOT) has experienced early age bridge deck cracking. ARDOT currently specifies a sequence deck pour on most of their bridges; however, contractors prefer continuous deck pours because of ease and construction time. During the period of this TRC1903 research project, ARDOT has only approved a few …

Numerical Simulations Of Spread Foundations Supported On Stone Columns Using The Discrete Element Method, Anibal Enrique Santos Marin

Graduate Theses and Dissertations

The implementation of stone columns as a ground improvement technique has become more popular in geotechnical construction practice as a result of their ability to improve strength, stiffness and permeability characteristics of weak clayey soil deposits. There are several analytical and empirical approaches to estimate the bearing capacity of stone column foundation systems; however, there is notable variation in the performance of these existing methods when compared with full-scale experimental results. For very weak cohesive soils (i.e., undrained shear strength less than 15 kPa), the use of conventional stone columns becomes restricted because of the insufficient confinement that these types …

Best Practices For Asphalt Emulsion Particle Size Analyses Using A Coulter Counter, Logan P. Kiihnl

Graduate Theses and Dissertations

As asphalt pavements develop distresses, pavement preservation, maintenance, and rehabilitation treatments are used to mitigate distresses and extend the life of the pavement. Many of these treatments utilize asphalt emulsion. Previous research has linked particle size to material properties including viscosity and storage stability. General statements have also been made about particle size influencing emulsion performance while other researchers have identified a trend between particle size and prime coat penetration. Even though literature discusses the importance of particle size, there is little guidance on the best practices of asphalt emulsion particle size analyses, specifically with a Coulter counter.

Data collected …

Development Of Multi-Axial Fatigue Retrofits For Lock Gate Components, Logan Verkamp

Graduate Theses and Dissertations

Lock gates are essential infrastructure components to the United State (US) supply chain. They create large cost savings and environmental benefits when compared with traditional methods of transport (freight and rail). Because of the large quantity of goods and dependence on these shipping chains, the US economy can be drastically affected by an unexpected gate closure. Unfortunately, many lock gates within the US have reached or exceeded their designed life. Due to the intensity of cyclic loads and the environment, fatigue cracks have become a prominent issue. Developed cracks near the pintle region (a joint which the gate rotates and …