Civil and Environmental Engineering Commons^™

Evaluation Of Deterioration Of Structural Concrete Due To Chloride Intrusion And Other Damaging Mechanisms, Sudhir Palle, Brian K. Howell, Theodore Hopwood Ii, Bobby W. Meade

Kentucky Transportation Center Research Report

Kentucky's bridges continue to age and experience distress. The intrusion of chlorides into concrete remains the primary mechanism for deterioration. It leads to reinforcing steel corrosion that damages the adjoining concrete structure. This study found problematic chloride concentrations in Kentucky concrete bridge elements (decks, pier caps, abutments). Chloride levels have been found at concentrations sufficient to initiate reinforcing steel corrosion. In some cases, chloride concentrations were sufficient to cause accelerated corrosion and produce major section loss of reinforcing steel. Advanced stages of corrosion such as these typically require costly repairs and maintenance to extend the service life of bridges.

Field …

Weak Magnetic Field Accelerates Chromate Removal By Zero-Valent Iron, Pian Feng, Xiaohong Guan, Yuankui Sun, Wonyong Choi, Hejie Qin, Jianmin Wang, Junlian Qiao, Lina Li

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Weak magnetic field (WMF) was employed to improve the removal of Cr(VI) by zero-valent iron (ZVI) for the first time. The removal rate of Cr(VI) was elevated by a factor of 1.12-5.89 due to the application of a WMF, and the WMF-induced improvement was more remarkable at higher Cr(VI) concentration and higher pH. Fe2+ was not detected until Cr(VI) was exhausted, and there was a positive correlation between the WMF-induced promotion factor of Cr(VI) removal rate and that of Fe²⁺ release rate in the absence of Cr(VI) at pH 4.0-5.5. These phenomena imply that ZVI corrosion with Fe^{2+ …}

Friction Bit Joining Of Dissimilar Combinations Of Advanced High-Strength Steel And Aluminum Alloys, Lile P. Squires

Theses and Dissertations

Friction bit joining (FBJ) is a new method that enables lightweight metal to be joined to advanced high-strength steels. Weight reduction through the use of advanced high-strength materials is necessary in the automotive industry, as well as other markets, where weight savings are increasingly emphasized in pursuit of fuel efficiency. The purpose of this research is twofold: (1) to understand the influence that process parameters such as bit design, material type and machine commands have on the consistency and strength of friction bit joints in dissimilar metal alloys; and (2) to pioneer machine and bit configurations that would aid commercial, …

Electrochemical-Mechanistic Model For Concrete Cover Cracking Due To Corrosion Initiated By Chloride Diffusion, Goli Nossoni, Ronald S. Harichandran

Civil Engineering Faculty Publications

A holistic electrochemical-mechanistic model of the corrosion of steel reinforcing bars inside concrete that accounts for the diffusion of oxygen and moisture into the concrete and rust layers, the densification of rust due to confinement, the flow of rust into the concrete pores, the development of internal pressure due to rust buildup, and cracking of the concrete cover is presented. The relationship between the corrosion current and the pressure buildup due to the corrosion products for different concrete cover thicknesses and concrete quality was calibrated through experiments using an accelerated corrosion test with an applied current. Results from finite-element analysis …

Flexural Behavior Of Reinforced Concrete T-Beams Strengthened With Nsm Composite System Under Accelerated Corrosion., Anes Bouchair

Theses

This research work aims at evaluating the effects of corrosion on flexural response of simply supported reinforced concrete (RC) T-Beams strengthened with near-surface-mounted carbon fiber-reinforced polymer (NSM-CFRP) strips. The research comprised experimental testing and analytical modelling. Test parameters included concrete grade, amount of NSM-CFRP strips, presence of U-wraps along the beam span, and time of corrosion exposure. A total of eighteen reinforced concrete beams with a T-shaped cross section were tested. Fourteen beams were strengthened in flexure and four beams were not strengthened to act as benchmarks. The strengthening regime included installation of either two or four NSM-CFRP strips into …

Sensitivity Of Electrochemical Impedance Spectroscopy Measurements To Concrete Bridge Deck Properties, Hillary Mckenna Argyle

Theses and Dissertations

Numerous methods have been developed to measure corrosion potential relating to chloride infiltration in concrete, including an emerging application of electrochemical impedance spectroscopy (EIS). EIS involves measurements of electrical impedance to evaluate the corrosion potential of steel reinforcement in concrete. With EIS, current is injected vertically into the concrete bridge deck between the surface and the embedded reinforcing steel, usually the top mat, to evaluate the degree to which the reinforcing steel is protected from chloride infiltration by the entire bridge deck system. The objectives of this research were to 1) investigate the sensitivity of EIS measurements obtained at various …

Development Of A Chloride Concentration Sampling Protocol For Concrete Bridge Decks, Sharlan Renae Montgomery

Theses and Dissertations

As the primary cause of concrete bridge deck deterioration in the United States is corrosion of the steel reinforcement as a result of the application of chloride-based deicing salts, chloride concentration testing is among the most common techniques for evaluating the condition of a concrete bridge deck. The objectives of this research were to 1) compare concrete drilling and powder collection techniques to develop a sampling protocol for accurately measuring chloride concentrations and 2) determine the number of chloride concentration test locations necessary for adequately characterizing the chloride concentration of a given bridge deck. Laboratory experiments on concrete drilling and …

Corrosion Activity In Precast Concrete Elements And Cementitious Closure Pours, Shabi Abbas Udaipurwala

All Theses

The use of prefabricated elements in the construction of highway bridges has been a common practice in the United States since 1950s. Precast concrete adjacent box beam girder bridges are quite popular given that the precast elements not only have structural capacity to span across the supports, but also form the bridge deck. These bridges have generally performed well during the initial years after construction, but recent failures in Pennsylvania and Indiana have aroused a nationwide alarm to investigate the causes of failure and find solutions to repair these bridges or develop design for new replacement bridges. It was found …

Structural Reliability Analysis Of Corroded Steel Girder Bridge, Mohammed Shaalan Al Badran

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The natural aging, environmental impact, and appropriate design are certainly playing a serious role in safety of the bridges function. The functional safety of bridge constitutes a prime element of the transportation system serving commuters, passengers and freight. According to Federal Highway Administration, the steel bridges share represents a large amount of the United States’ bridges. In last century, the collapse of both the Silver Bridge at Point Pleasant, West Virginia over the Ohio River on December 15, 1967 and over the Mianus River Bridge in Connecticut on June 28, 1983 showed that steel corrosion has been the leading reason …

Performance Of Reinforced Concrete Beams Strengthened With Mechanically-Fastened Composite System Under Corrosive Environment, Amna Zaid Suwaid Al Nassibi

Theses

This study examines the effects of corrosion exposure on the flexural response of reinforced concrete (RC) beams strengthened with a powder-actuated fastened (PAF) composite system. Twenty-one RC beams were constructed and tested to failure under four-point bending. The corroded beams were subjected to 30, 60, and 100 days of accelerated corrosion that corresponded to measure tensile steel mass losses of 6, 11 and 18% respectively. Other test parameters included width of fiber reinforced polymer (FRP) composite strip, fastener length, and number of fasteners rows.

For the non-corroded beams, the PAF-FRP system resulted in up to 24% increase in beam flexural …

In-Plant And Distribution System Corrosion Control For Reverse Osmosis, Nanofiltration, And Anion Exchange Process Blends, Samantha Jeffery

Electronic Theses and Dissertations

The integration of advanced technologies into existing water treatment facilities (WTFs) can improve and enhance water quality; however, these same modifications or improvements may adversely affect finished water provided to the consumer by public water systems (PWSs) that embrace these advanced technologies. Process modification or improvements may unintentionally impact compliance with the provisions of the United States Environmental Protection Agency’s (USEPA’s) Safe Drinking Water Act (SDWA). This is especially true with respect to corrosion control, since minor changes in water quality can affect metal release. Changes in metal release can have a direct impact on a water purveyor’s compliance with …

Assessment Of Damage In Concrete Structures Using Acoustic Emission, Marwa Abdelrahman

Theses and Dissertations

Evaluating the integrity of concrete structures is an essential procedure to ensure structural safety and durability. Non-destructive testing (NDT) is needed for localizing and characterizing the growing damage in existing structures and also for quality control of new structures. Visual inspection is a commonly used method; however it is not suitable for early detection of damage and very dependent on the experience of the inspector. More research is needed to establish advanced methods for structural health diagnosis such as acoustic emission (AE). Acoustic emission is notably sensitive to active damage in concrete structures. This thesis includes three studies that mainly …

Assessing Corrosion Damage In Post -Tensioned Concrete Structures Using Acoustic Emission & A Preliminary Investigation Of Biopolymer Doped Cement Mortar For Use In Structural Restoration, Aditya Appalla

Theses and Dissertations

A sizeable portion of the civil infrastructure is made from concrete. An estimate shows that about 7 billion cubic meters of concrete is made annually worldwide. With the deterioration of the infrastructure due to aging or external factors, significant monetary and technological investment is needed for condition evaluation, maintenance and repair. Two areas that account for a considerable portion of this investment are condition evaluation for maintenance of corroded concrete structures and mortar patching for repair and rehabilitation.

The primary method of evaluation of a structure is by visual inspection. But this method is limited as some crucial areas in …

Kelvin Probe Electrode For Contactless Potential Measurement On Concrete-Properties And Applications, Michael Thomas Walsh

USF Tampa Graduate Theses and Dissertations

The practical feasibility of using a Kelvin Probe as a novel reference electrode in the measurement of both potential and polarization pulse response of reinforcing steel in concrete is demonstrated. Potential values measured using a KP reflect greater stability and repeatability than can typically be attained with conventional reference electrodes. Duplicate reinforced concrete beam test specimens with well-differentiated centrally corroding rebar segments were analyzed using both the Kelvin Probe (KP) and a conventional Saturated Calomel Electrode (SCE). Potential profile maps were developed using potential values recorded under static conditions with both the SCE and the KP. Nominal polarization resistance was …

Durability Of Reinforced Concrete Incorporating Crushed Waste Brick As Coarse Aggregate, Matthew Adamson

All Theses

Using crushed bricks as aggregates in concrete is of particular interest to preserve natural aggregate sources as well as to reduce waste, as it has been estimated that 10% to 30% of all waste in landfills in the united States comes from construction and demolition wastes. By recycling some of these wastes, the sustainability of a project can be improved. However, it is important concrete incorporating these wastes is as durable or more durable then conventional concrete, or will it have a shorter service life. Durability of concrete is its ability to resist deterioration from its external environment such as …

New Coatings For Bridges (Over-Coat Systems), Sudhir Palle, Theodore Hopwood Ii, Bobby W. Meade

Kentucky Transportation Center Research Report

KYTC sought to identify new coatings technologies consistent with overcoating that offer enhancements in terms of ease of application and performance. KYTC contacted paint manufacturers to obtain sample coating systems for characterization by the KYTC Division of Materials and accelerated performance testing by Kentucky Transportation Center (KTC). A total of 14 coating systems from five manufacturers underwent performance testing according to ASTM D5894.

Safety Stock Estimation Of Unit Load Devices For International Airline Operations, Hua-An Lu, Chien-Yi Chen

Journal of Marine Science and Technology–Taiwan

Unit load devices (ULDs) are used to load air cargo and passengers’ checked baggage for wide-bodied aircraft operations. Since ULDs are reusable at the destination, airlines can invest in an appropriate fleet size for their requirements. The estimation of safety stock levels for every operating airport is a premeditated task because airlines must prepare enough devices for the outbound consignments of each flight. The variance of the number of used devices for each arrival and departure flight will influence the stock level of an airport. For scheduled international services, this study proposes an analytic method based on a cyclically time-sequenced …

Evaluating Corrosion Control Alternatives For A Reverse Osmosis, Nanofiltration And Anion-Exchange Blended Water Supply, Rebecca J. Wilder

Electronic Theses and Dissertations

The research reported herein describes the study activities performed by University of Central Florida (UCF) on behalf of the Town of Jupiter Water Utilities (Town). The Town recently changed its water treatment operations from a combination of reverse osmosis (RO), lime softening (LS) and anion-exchange (IX) to a combination of RO, IX and nanofiltration (NF). Although this treatment change provided enhanced water to the surrounding community in terms of better contaminant removal and reduced DBP formation potential, integration of the NF process altered finished water quality parameters including pH, alkalinity and hardness. There was concern that these changes could result …

Strengthening Of Reinforced Concrete Beams Pre-Damaged In Shear, Yousef Mohammed Bachar Chekfeh

Theses

Repair and strengthening of existing reinforced concrete (RC) structures has increased drastically in recent years. Shear reinforcement in RC beams is typically of a small bar diameter, and hence any shear-damage would result in a severe safety hazard and a catastrophic mode of failure especially under extreme loading events. The present work was initiated to the effectiveness of different composite strengthening systems; namely externally bonded carbon fiber reinforced polymer (EB-CFRP), and near surface mounted glass fiber reinforced polymer (NSM-GFRP) to prolong the functional service life of RC beams pre-damaged in shear. It comprised experimental testing and analytical investigation.

The experimental …

Modern Protection Systems To Prevent Corrosion Of Structural Steel Elements Due To Deicing And Roadway Salts, John J. Myers, Wei Zheng

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The effectiveness of innovative polymeric coatings, polyurea and Poly aspartic polyurea, to protect structural steel from corrosion was investigated through standard laboratory tests. the coating evaluation tests included salt fog test, QUV weathering test, adhesion test, and freeze-thaw stability test. These tests were used to assess the long-term performance of coating technologies compared to the conventional polyurethane type coatings, i.e. coating systems with inorganic zinc primer, epoxy intermediate coat and polyurethane topcoat. This paper presents part of results in the aforementioned evaluation tests. the results illustrate that Poly aspartic coating systems are very promising for corrosion mitigation and can provide …

Oxygen Diffusion Characterization Of Frp Composites Used In Concrete Repair And Rehabilitation, Chandra K. Khoe

USF Tampa Graduate Theses and Dissertations

Many independent studies have conclusively demonstrated that fiber reinforced polymers (FRP) slow down chloride-induced corrosion of steel in concrete. The mechanism for this slow down is not well understood but it has been hypothesized that FRP serves as a barrier to the ingress of chloride, moisture, and oxygen that sustain electrochemical corrosion of steel.

This dissertation presents results from an experimental study that determined the oxygen permeation rates of materials used in infrastructure repair. In the study, the oxygen permeation constants for epoxy, carbon and glass fiber laminates, concrete, epoxy-concrete and FRP-concrete systems were determined and a method developed to …

Elimination Of Deck Joints Using A Corrosion Resistant Frp Approach, Ashok Reddy Aleti

Doctoral Dissertations

The research presented herein describes the development of durable link slabs for jointless bridge decks based on using FRP grid for reinforcement. Specifically, the ductility of the FRP material was utilized to accommodate bridge deck deformations imposed by girder deflection, temperature variations, and concrete shrinkage. It would also provide a solution to a number of deterioration problems associated with bridge deck joints.

The design concept of the link slabs was then examined to form the basis of design for FRP grid link slabs. Improved design of FRP grid link slab/concrete deck slab interface was confirmed in the numerical analysis. The …

Mitigation Of Chloride And Sulfate Based Corrosion In Reinforced Concrete Via Electrokinetic Nanoparticle Treatment, Kunal Kupwade-Patil

Doctoral Dissertations

Concrete is a porous material which is susceptible to the migration of highly deleterious species such as chlorides and sulfates. Various external sources, including sea salt spray, direct seawater wetting, deicing salts and chlorides can contaminate reinforced concrete. Chlorides diffuse into the capillary pores of concrete and come into contact with the reinforcement. When chloride concentration at the reinforcement exceeds a threshold level it breaks down the passive oxide layer, leading to chloride induced corrosion. The application of electrokinetics using positively charged nanoparticles for corrosion protection in reinforced concrete structures is an emerging technology. This technique involves the principle of …

Service Life Prediction Of Pier For The Existing Reinforced Concete Bridges In Chloride-Laden Environment, Ming-Te Liang, Ran Huang, Shen-An Feng, Chi-Jang Yeh

Journal of Marine Science and Technology–Taiwan

The prediction method of service life for bridge structures is played an important role of bridge management system. In this paper, the mathematical modeling was to study the servise life prediction of pier for existing reinforced concrete (RC) bridge exposed to chloride environment. The corrosion process has three stages, the initiation time (tc), the depassivation time (tp), and the corrosion (propagation) time (tcorr). The total service life of pier for the existing RC bridge can be expressed as t = tc + tp + tcorr. Many mathematical models were applied to predicting each value of the tc, tp, and tcorr. …

Applications Of Electricity In The Rehabilitation And Health Monitoring Of Concrete Structures, Saiprasad Vaidya

Doctoral Dissertations

The dissertation research work presented herein consists of two separate findings: one investigates a potential new coating technique that could be used to rehabilitate deteriorated concrete sewer pipes, and the other researches inducing electrical conductivity into geopolymer concrete to serve as smart material by being able to sense stress changes. Both applications utilize electricity to enhance the performance and/or functionality of hardened cementitious materials.

Microbiologically induced corrosion (MIC) in concrete wastewater conveyance systems is a leading deterioration mechanism in such structures. This work focuses on breaking the MIC cycle by preventing colonization of the bacteria responsible for converting hydrogen sulfide …

Simulation And Behavior Of Corrosion Deteriorated Reinforced Concrete Members, M. A. Shayanfar, Amir Safiey

Publications

Several reinforced concrete (RC) infrastructures are now crumbling from corrosion of steel bars in concrete. The paper presents the recent advancements in analytical simulation of corrosion aftereffects on behavior of RC members. The model juxtaposes the experimental findings with analytical relationships. The implementation of the model into a nonlinear finite element formulation as well as the experimental and analytical backgrounds are discussed. The abilities of the resulted program have been studied by modeling some experimental specimens showing a reasonable agreement between the analytical and experimental findings.

Nondestructive Method To Detect Corrosion Of Steel Elements In Concrete, Saeed Javidi Niroumand, Aaron Jon Yakel, Atorod Azizinamini, Marcelo Dasilva

Nebraska Department of Transportation: Research Reports

No abstract provided.

A New Approach For Nonlinear Finite Element Analysis Of Reinforced Concrete Structures With Corroded Reinforcements, Mohsen A. Shayanfar, Amir Safiey

Publications

A new approach for nonlinear finite element analysis of corroded reinforcements in reinforced concrete (RC) structures is elaborated in the article. An algorithmic procedure for producing the tension-stiffening curve of

RC elements taking into consideration most of effective parameters, e.g.: the rate of steel bar corrosion, bond-slip behavior, concrete cover and amount of reinforcement, is illustrated. This has been established on both experimental and analytical bases. This algorithm is implemented into a nonlinear finite element analysis program. The abilities of the resulted program have been studied by modeling some experimental specimens showing a reasonable agreement between the analytical and experimental …

Impact Of Corrosion Inhibitor Blended Orthophosphate On Water Quality In Water Distribution Systems, Abdulrahman Alshehri

Electronic Theses and Dissertations

The impact of blended orthophosphate (BOP) inhibitor addition on the corrosion of iron, copper, and lead in drinking water distribution systems was studied under changing water quality environment. Release of iron, copper, and lead were monitored at varying inhibitor doses and changing blends of source waters (groundwater, surface water, and desalinated water). Solid corrosion products on pipe surfaces under BOP treatment were evaluated with surface characterization techniques. Performance of the BOP inhibitor was compared to other corrosion control strategies. Iron scales for iron and galvanized steel coupons incubated in different blended waters in the presence of BOP inhibitor were analyzed …

Sensitivity Of Half-Cell Potential Measurements To Properties Of Concrete Bridge Decks, Thad Marshall Pinkerton

Theses and Dissertations

Half-cell potential testing has been recommended as a non-destructive method for assessing the corrosion potential of reinforcing steel in concrete bridge decks. The technique is particularly useful because it can be utilized to evaluate the probability of corrosion before damage is evident at the surface of a bridge deck. The specific objective of this research was to quantify the effects of age, chloride concentration, concrete cover thickness, spatial position, temperature, and presence or condition of epoxy coating on half-cell potential measurements of concrete bridge decks typical of those in Utah. The laboratory testing associated with this research followed a full-factorial …