Civil and Environmental Engineering Commons^™

Estimation Of The Service Life Of Span Structures In Predicting The Durability Of Reinforced Concrete Bridges, Sh.B. Akhmedov, Kh. Almenov, Sh.Sh. Shojalilov, Sh.Sh. Safarov

The Scientific Journal of Vehicles and Roads

In recent years, on the roads of Uzbekistan and other countries, there has been a dangerous increase in various damages in the operated superstructures, caused by an increase in the service life and traffic intensity of vehicles and cargo tension.

Design And Detailing Of Cast-In-Place And Precast Concrete Approach Slabs, George Morcous, Mostafa Abo-Elkhier

Nebraska Department of Transportation: Research Reports

Approach slab is a structural concrete slab that spans from the backwall of the abutment (i.e. end of the bridge floor) to the beginning of the paving section. The purpose of the approach slab is to carry the traffic loads over the backfill behind the abutments to avoid differential settlement that causes bumps at the bridge ends. Cast- in-place concrete approach slab is the current practice in US with various spans, reinforcement, thicknesses, joints, and concrete covers. NDOT has observed premature cracking in a significant number of approach slabs, which could result in a shorter service life and costly repairs/replacements …

Bridge Prioritization And Preservation Along Route 66, Sarah Ballard

Open Access Theses & Dissertations

Eligible bridges around the United States receive federal funding every year for replacement or rehabilitation. The main criterion for allocation of this funding is based on engineering aspects (e.g., life safety, condition, functionality), often leaving the historical value of the bridge at the bottom of the importance level. One of the main historical roads known in America is Route 66, also known as the â??Mother Road.â?? This route was the road to opportunity in the 1930s. Many bridges with historical significance carry the route and represent an integral part of the history of the Mother Road. This research analyzes bridges …

Structural Identification And Damage Detection In Bridges Using Wave Method And Uniform Shear Beam Models: A Feasibility Study, Mehran Rahmani, Manan Naik

Mineta Transportation Institute

This report presents a wave method to be used for the structural identification and damage detection of structural components in bridges, e.g., bridge piers. This method has proven to be promising when applied to real structures and large amplitude responses in buildings (e.g., mid-rise and high-rise buildings). This study is the first application of the method to damaged bridge structures. The bridge identification was performed using wave propagation in a simple uniform shear beam model. The method identifies a wave velocity for the structure by fitting an equivalent uniform shear beam model to the impulse response functions of the recorded …

An Analysis Of A Hybrid Steel Bridge, Andrew Iglehart

Mahurin Honors College Capstone Experience/Thesis Projects

The American Institute of Steel Construction hosts a competition for graduating college seniors each year. The competition is designing and fabricating a scaled steel bridge within certain parameters. Each year the parameters change to allow different seniors to face similar challenges without copying the previous year’s work. Before the outbreak of COVID-19, a bridge was fabricated as per the rules in the 2020, and the same bridge was used for the 2021 competition. With a bridge already fabricated and being used for the competition, a question arose about analyzing the bridge.

This thesis encompasses the entire analysis of the steel …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Causey Reservoir Access Project: Improving Visitor Safety And Access Now And For The Future, Michael Merrill, Carly Jo Petersen, Isaiah Norman, Jordan Jones, Nathan Chidester

Civil and Environmental Engineering

In coordination with the Central Federal Lands Highway Division, the Causey Reservoir Access Project is a multidisciplinary endeavor to address infrastructural deficiencies around Causey Reservoir. The reservoir is a high-use land- and water-based recreation site on Cache National Forest, about a half hour east of Ogden, Utah. This project addresses a deteriorating bridge, insufficient parking, and roads damaged by landslides as shown in Figure 1.

Studies On Tornado-Structure Interactions And Guidance On Design Tornadic Wind Loading, Zhi Li

Doctoral Dissertations

“Tornadoes are violent natural hazards that could caused significant property loss and fatalities. Statistical data indicates that most fatalities during tornado incidents were caused by the building failure under tornadoes. For example, in the 2011 Joplin Tornado, 161 people were killed, and 84 percent of the fatalities were related to the failure of buildings. In addition, most of the significant, tornado-induced property loss and fatalities are relevant to the tornadoes passing through the densely populated regions. Besides buildings, bridges were also severely damaged or destroyed by tornadoes in the United States. To reduce the tornado-induced loss, it is imperative to …

Utilizing Kryton Kim Technology In Bridge Deck And Rail Construction To Protect Against Chloride Ion Penetration, Mick Syslo, Wally Heyen, Lieska Halsey, David Hansen, Tim Kranson

Nebraska Department of Transportation: Research Reports

No abstract provided.

Lessons Learned From Six Different Structural Health Monitoring Systems On Highway Bridges, Abheetha Peiris, Charlie Sun, Issam E. Harik

Kentucky Transportation Center Faculty and Researcher Publications

Structural health monitoring has been utilized in numerous ways to investigate the performance and integrity of highway bridges. This paper highlights the use of six structural health monitoring systems, which were deployed to monitor distinct behaviors on six bridges in Kentucky. The structural health monitoring systems are as follows: (1) Over-height truck impact detection and monitoring on the I-64 over US 60 bridge, (2) Barge impact detection and monitoring on northbound US 41 over the Ohio River, (3) effectiveness of carbon fiber-reinforced polymer retrofit evaluation based on prestressed concrete I-girder crack movement on the I-65 elevated expressway in Louisville, (4) …

Wooden Bridge Demolition And Reconstruction, Josh Simon Rogers

Construction Management

The Conejo Recreation and Park District (CRPD) is a nonprofit city government organization that maintains the parks and hiking trails in Thousand Oaks, California. They were informed that one of the bridges at the Stagecoach Inn, a landmark park located in Thousand Oaks California, was old and sagging in a way that made interfered with the flow of the creek it spanned over. A plan to demolish the current bridge was created. Utilizing ArchiCAD and Microsoft Excel a design and an estimate were developed for a new bridge that would be built in its place. This bridge would be tall …

Construction Of The Slo Botanical Gardens Foot Bridge - Interdisciplinary Project, Connor N. Layman

Construction Management

In the Winter quarter of 2020, a project based senior project was sought out by a Cal Poly Construction Management student, and he was connected with the San Luis Obispo Botanical Gardens (SLO BG). SLO BG is a non-profit organization located on 150 acres in the El Chorro Regional Park. After meeting with the SLO BG staff and exploring their many needed projects, the student and the staff mutually concluded that he would build a bridge and accompanying stairs which resided on a well-traveled trail on the property. He successfully developed the project schedule, budget, recruited an architect for design …

Experimental Static And Cyclic Behavior Of Hybrid Non-Metallic Bridge Decks Reinforced With Discrete Gfrp Rebar And Gfrp Macrofiber, Jared W. Mcrory

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Bridge deck corrosion is a major expense in the U.S. every year. The increased use of deicing salts in cold weather climates has led to corrosion of the steel reinforcement in bridge decks, which leads to spalling and delamination of the concrete cover. This results in costly rehabilitations or repairs, and more sustainable bridge deck solutions must be provided to prevent this cycle.

As a part of this research project, a corrosion-resistant, hybrid reinforcement strategy that is shown to be cost neutral with epoxy coated rebar is proposed. The hybrid reinforcement strategy, consisting of discrete Glass Fiber Reinforced Polymer (GFRP) …

Load Truncation Approach For Development Of Live Load Factors For Bridge Rating, Sasan Siavashi, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

Various local governments have developed state-specific vehicular live load factors for bridge rating. However, a significant computational demand is often associated with such an effort. This is due to the large size of the weigh-in-motion (WIM) databases frequently used in the procedure. In this study, a method is proposed that can significantly reduce the computational cost of the analysis, while still maintaining reasonable accuracy. The proposed approach develops approximate live load random variable statistics by truncating the WIM database based on gross vehicle weight, then a complete reliability analysis is conducted to develop new live load factors that meet AASHTO-specified …

Application Of Internal Curing To Improve Concrete Bridge Deck Performance, Arman Abdigaliyev, Yong-Rak Kim, Jiong Hu

Nebraska Department of Transportation: Research Reports

Due to the relatively high cement content and low water-to-cement ratio (w/c) used, bridge deck concrete is prone to premature cracking. Internal curing has been found to greatly reduce the chance of premature cracking as well as concrete deterioration. This research project was intended to develop internally cured bridge deck concrete based on a local mix design in Nebraska. Four different lightweight fine aggregate (LWFA) as internal curing agents were evaluated, and their effects on fresh, mechanical, durability, and shrinkage properties of concrete were studied. To identify the most effective LWFA dosage for shrinkage reduction, different replacement rates of sand …

Bridge Resilience Assessment With Inspire Data, Iris Tien, Yijian Zhang

Project RR-1

This project proposed a methodology to assess the impact of corrosion on the performance of bridges. The combined analytical and numerical modeling of shear-critical and lap-spliced columns is detailed, and outcomes are verified with previous experimental test data. The impact of corrosion on risk is assessed through conducting fragility analyses. Results quantify the increase in failure probabilities of these structures, measured by increasing probabilities of exceeding defined damage states, with increasing levels of corrosion. Corrosion is found to have a larger impact on increasing probabilities of exceeding more severe damage states. Twenty percent mass loss of reinforcement increases the probability …

Development Of An Ndt Tool For In-Situ Assessment Of Prestress Loss, Bibo Zhong, Jinying Zhu, George Morcous

Nebraska Department of Transportation: Research Reports

The research objective is to develop a non-destructive testing (NDT) method to evaluate the prestress loss in prestressed concrete bridge girders using ultrasonic waves. The work principle is based on acoustoelastic effect - ultrasonic wave velocity varies with stress level in prestressed concrete. A self-reference test setup was proposed to measure wave velocity in two orthogonal directions (prestress and unstressed directions) in the girder. This setup will be able to reduce effects of material variation and temperature change.

The concept was first validated on small concrete specimens (cylinders and beams) in laboratory. A signal analysis algorithm was developed to reliably …

Feasibility Study Of Development Of Ultra-High Performance Concrete (Uhpc) For Highway Bridge Applications In Nebraska, Flavia Ribeiro Furtado De Mendonca, Mostafa Abo El-Khier, George Morcous, Jiong Hu

Nebraska Department of Transportation: Research Reports

Ultra-high performance concrete (UHPC) is a new class of concrete that has superior mechanical, durability, and workability properties that far exceed those of conventional concrete. To achieve these properties, a specific mix design with a very dense internal structure, fiber reinforcement, and low water-to-binder ratio (w/b) is commonly used. The goal of this research is to develop a non-proprietary UHPC mix with constituent materials that are readily available in the state of Nebraska for bridge construction applications. In developing this mix, the particle packing model is used, and an experimental study of the impact of various design parameters on the …

Steel Bridge Truss Analysis, Alastair Seed

Williams Honors College, Honors Research Projects

The purpose of this project is to conduct a study comparing the effectiveness of different cross frame orientations in lowering the deflection of the main stringers of a bridge. Three different orientations of cross frames were researched; vertical, angled with the superstructure webbing, and halfway-angled. All of these were studied when the stringers were placed directly under the superstructure and when the superstructure was placed outside of the stringers. Analysis was performed in a program called SAP 2000 to find the deflections along the stringers under different loading conditions. The results showed that when the superstructure was oriented over the …

Box Elder Creek Trail And Bridge Design, Turky Al-Osaimi, Braiden Amata, Spencer Nielson, Michael Ruiz-Leon, Devon Vigil

Civil and Environmental Engineering

There is a light footpath that begins at Mayors pond in Brigham City and follows the Box Elder Creek north to the surrounding neighborhoods. The path is marked with faded pink utility ribbons. The footpath crosses through difficult terrain and twice through a dry creek bed. There is not a stable creek crossing. Residents seeking to use the current path are potentially exposing themselves to difficult crossings and unstable terrain.

The Brigham City Trails Task Force desires to construct a pedestrian trail for the community to safely recreate. The trail will connect residential areas to Mayors Pond. The proposed trail …

Hobbit Caves Access Bridge: Logan, Ut, Bailey Mabey, Katrina Mccoll, Hayley Sharkey, Spencer Tanner, Allison Valencia

Civil and Environmental Engineering

The National Forest Service proposed the reconstruction of a pedestrian bridge leading to the Logan Canyon Hobbit Caves. At the proposed location the previous bridge foundation failed leading to unsafe conditions.

Currently visitors must cross the creek on foot to access the Hobbit Caves. This disrupts the local habitat. This also creates a hazard for the public due to high variance in flow rate and water level of the creek. A new location was selected and the design criteria was created based upon this new location.

Long-Term Performance Evaluation Of Nudeck In Kearney East Bypass, George Morcous, Marc Maguire

Nebraska Department of Transportation: Research Reports

The Kearney East Bypass bridge is the first project that implements the newly developed precast concrete deck system (known as 2nd generation NUDECK). The new system consists of full-depth full-width precast prestressed concrete deck panels that are 12 ft (3.66 m) long each. The panels have covered shear pockets at 4 ft (1.22 m) spacing on each girder line to host clustered shear connectors that are adjustable in height. Narrow unreinforced transverse joints are used to eliminate the need for deck overlay. Also, deck panels are post-tensioned in the longitudinal direction using a new post-tensioning system that eliminates the need …

Standard Design For Nebraska County Bridges, Chungwook Sim, Jiong Hu, Maher K. Tadros, Alexander Bleyhl, David Gee

Nebraska Department of Transportation: Research Reports

Many county-owned bridges in Nebraska need replacement due to their structural deficiency. Most of the bridges needing replacement are in the 40 to 60 ft range. This span range lacks a standard design that fits Nebraska county practices in terms of speed and simplicity of construction. The current systems being used are (a) Precast 1 by 2 ft planks which can span up to 30 ft, (b) Cast-in-place slab bridges which can span up to 50 ft but require extensive field formwork, concrete placing, and curing, and are best when constructed in three-span units, and (c) Inverted tees which can …

Precast Concrete Deck-To-Girder Connection Using Uhpc, George Morcous, Mostafa Abo El-Khier

Nebraska Department of Transportation: Research Reports

The implementation of ultra-high-performance concrete (UHPC) in bridge construction has been growing rapidly in the last two decades due to its excellent mechanical properties, workability, and durability. This report presents a new UHPC connection between precast concrete deck panels and bridge girders that eliminates changes to the design and production of girder shear connectors commonly used in conventional cast-in-place concrete deck construction. In conventional construction, girder shear reinforcement or studs are extended into the cast-in-place concrete deck to transfer interface shear and create composite section. In the new connection, girder shear reinforcement or studs are kept underneath the deck panels, …

Condition Assessment Of Bridge Decks With Asphalt Overlay, Sepehr Pashoutani, Jinying Zhu

Nebraska Department of Transportation: Research Reports

Ground penetrating RADAR (GPR) is a widely used nondestructive testing (NDT) method for bridge deck evaluation. However, the current GPR signal and data processing software and algorithms are not able to provide comprehensive information about bridge deck condition. Although the original objective of this research project was to develop GPR analysis algorithms for condition assessment of bridge decks with asphalt overlay, the scope of work has been expanded to concrete bridge decks with or without overlays.

In this study, the research team developed a complete GPR analysis procedure that includes the following components: 1) obtain zero-time for GPR reflection at …

A Practitioner’S Guide To Small Unmanned Aerial Systems For Bridge Inspection, Sattar Dorafshan, Robert J. Thomas, Calvin Coopmans, Marc Maguire

Electrical and Computer Engineering Faculty Publications

Small unmanned aerial system(s) (sUAS) are rapidly emerging as a practical means of performing bridge inspections. Under the right condition, sUAS assisted inspections can be safer, faster, and less costly than manned inspections. Many Departments of Transportation in the United States are in the early stages of adopting this emerging technology. However, definitive guidelines for the selection of equipment for various types of bridge inspections or for the possible challenges during sUAS assisted inspections are absent. Given the large investments of time and capital associated with deploying a sUAS assisted bridge inspection program, a synthesis of authors experiences will be …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Data

Corresponding data set for Tran-SET Project No. 18CNMS01. Abstract of the final report is stated below for reference:

"This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that …

Structural Vulnerability Of Coastal Bridges Under Extreme Hurricane Conditions, Arturo Montoya, Adolfo Matamoros, Firat Testik, Reza Nasouri, Adnan Shahriar, Arsalan Majlesi

Data

Corresponding data set for Tran-SET Project No. 18STTSA04. Abstract of the final report is stated below for reference:

"This work presents the results of a numerical study evaluating the response of coastal bridges due to hurricane-induced waves. The analyses were conducted using the Coupled Eulerian-Lagrangian (CEL) approach, available on the commercial finite element software Abaqus, which allows modeling the interaction between water and the bridge. The work concentrated on (1) establishing an approach for modeling the desired wave characteristics (i.e., wave height, and frequency) within the CEL simulation, (2) conducting simulations using actual bridge dimensions of historically damaged bridges, (3) …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Publications

This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that locally produced UHPC has excellent mechanical and durability properties. UHPC has also been shown to have good bonding …

Performance Evaluation Of Inverted Tee (It) Bridge System, Garrett P. Martindale, Daniel Watson, Antony Mohsen Kamal Masoud Kodsy, Mostafa Abo El-Khier, Richard L. Wood, George Morcous

Nebraska Department of Transportation: Research Reports

The Inverted Tee (IT) girder bridge system was originally developed in 1996 by the University of Nebraska–Lincoln (UNL) researchers and Nebraska Department of Transportation (NDOT) engineers. This bridge system currently accounts for over 110 bridges in Nebraska used for both state highways and local county roads. Extensive longitudinal and transverse deck cracking have been observed and noted in numerous bridge inspection reports. Since the IT girder bridge system is relatively new, limited data and knowledge exist on its structural performance and behavior. This study evaluates the IT girder bridge system by conducting twenty field observations as well as recording accelerometer, …