Civil and Environmental Engineering Commons^™

Importance Of The Tail In Truck Weight Modeling For Bridge Assessment, Eugene J. Obrien, Bernard Enright, Abraham Getachew

Articles

To predict characteristic extreme traffic load effects, simulations are sometimes performed of bridge loading events. To generalize the truck weight data, statistical distributions are fitted to histograms of weight measurements. This paper is based on extensive WIM measurements from two European sites and shows the sensitivity of the characteristic traffic load effects to the fitting process. A semi-parametric fitting procedure is proposed: direct use of the measured histogram where there are sufficient data for this to be reliable and parametric fitting to a statistical distribution in the tail region where there are less data. Calculated characteristic load effects are shown …

A New Congested Traffic Load Model For Highway Bridges, Colin C. Caprani, Colm Carey, Bernard Enright

Conference papers

Long span highway bridges are critical components of any nation’s infrastructure. Therefore accurate assessment of highway bridge loading is essential, and it is well known that congested traffic governs load effect for such bridges. Current congestion models use conservative assumptions about traffic and inter-vehicle gaps. This research investigates congested traffic flow through the use of traffic microsimulation which has the ability to reproduce complex traffic phenomena based on driver interactions. A time series model has been developed to produce a speed time-series similar to the results of the microsimulation. The speed time-series from the new model, combined with the established …

The Influence Of Correlation On The Extreme Traffic Loading Of Bridges, Eugene J. Obrien, Bernard Enright, A. T. Dempsey

Conference papers

Accurate traffic loading models based on measured data are essential for the accurate assessment of existing bridges. There are well-established methods for the Monte Carlo simulation of single lanes of traffic, and this can easily be extended to model the loading on bridges with two independent streams of traffic in opposing directions. However, a typical highway bridge will have multiple lanes in the same direction, and various types of correlation are evident in measured traffic. This paper analyses traffic patterns using multi-lane WIM data collected at two European sites. It describes an approach to the Monte Carlo simulation of this …

Management Strategies For Special Permit Vehicles For Bridge Loading, Bernard Enright, Eugene J. Obrien

Conference papers

An examination of weigh-in-motion data collected recently at sites in five European countries has shown that vehicles with weights well in excess of the normal legal limits are found on a daily basis. These vehicles would be expected to have permits issued by the responsible authorities. It can be seen from the measurements that most of them are travelling at normal speeds. Photographic evidence indicates that, while many are accompanied by an escort vehicle, normal traffic is flowing alongside in other lanes. As European freight volume grows, the frequency of these special vehicles can be expected to increase. Hence, the …

Service Life Prediction Of Pier For The Existing Reinforced Concete Bridges In Chloride-Laden Environment, Ming-Te Liang, Ran Huang, Shen-An Feng, Chi-Jang Yeh

Journal of Marine Science and Technology–Taiwan

The prediction method of service life for bridge structures is played an important role of bridge management system. In this paper, the mathematical modeling was to study the servise life prediction of pier for existing reinforced concrete (RC) bridge exposed to chloride environment. The corrosion process has three stages, the initiation time (tc), the depassivation time (tp), and the corrosion (propagation) time (tcorr). The total service life of pier for the existing RC bridge can be expressed as t = tc + tp + tcorr. Many mathematical models were applied to predicting each value of the tc, tp, and tcorr. …

Strengthening Of Rural Bridges Using Rapid-Installation Frp Technology: Route 63 Bridge No. H356, Phelps County, Dongming Yan, Jianbo Li, Chenglin Wu, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This report presents the use of externally bonded fiber reinforced polymers (FRP) laminates for the flexural strengthening of a concrete bridge. The bridge selected for this project is a two-span simply supported reinforced concrete slab with no transverse steel reinforcement located in Phelps County, MO. The original construction combined with the presence of very rigid parapets caused the formation of a 1-inch wide longitudinal crack, which resulted in the slab to behave as two separate elements. The structural behavior was verified using a finite element model (FEM) of the bridge. The bridge analysis was performed for maximum loads determined in …

Earthquake Resistance Of Integral Abutment Bridges, Robert J. Frosch, Michael E. Kreger, Aaron M. Talbott

JTRP Technical Reports

intermediate length bridges. Integral abutment construction eliminates joints and bearings which reduce long-term maintenance costs. However, in the absence of joints and bearings, the bridge abutments and foundations must be able to accommodate lateral movements from thermal expansion and contraction of the superstructure and from seismic events. Previous research has focused on the response to thermal expansion and contraction. The current research examines the response of integral abutment bridges to seismic loading. A field investigation was conducted to examine the response of an integral abutment to lateral loading from thermal expansion and contraction. The results were used to calibrate analytical …

Laboratory Testing Of Precast Bridge Deck Panel Transverse Connections For Use In Accelerated Bridge Construction, Scott D. Porter

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Precast concrete bridge deck panels have been used for decades to accelerate bridge construction. Cracking of the transverse connection between panels is a common problem that can damage deck overlays and cause connection leaking leading to corrosion of lower bridge elements.

To better understand the behavior of bridge deck transverse female-to-female connections, shear and moment lab testing were performed at Utah State University for the Utah Department of Transportation. Two existing UDOT connections were tested, a welded stud connection and a post tensioned connection. A variation of the welded connection using rebar was also tested. In addition, two new curved …

Analysis Of Effectiveness Of Bridges With Partial Isolation, Wenying Hu

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

A special class of seismically isolated bridges shares a common feature in that both ends of the superstructure are restrained and isolators over the columns of bridge uncouple the superstructure from the ground motions. They are defined as partial isolation bridges. From measured acceleration responses, effectiveness of full seismic isolation had been confirmed widely. However, the seismic isolation behavior in the partial isolation has not been widely observed.

The effectiveness of partial isolation is evaluated in this study. The static design procedures for linear and nonlinear partially isolated bridges are developed. Results from the static analysis of linear and nonlinear …

Effect Of Initial Scarification And Overlay Treatment Timing On Chloride Concentrations In Concrete Bridge Decks, Curtis Daniel Nolan

Theses and Dissertations

Considering the pervasive presence of chlorides in concrete bridge decks, bridge engineers have a critical responsibility to perform proper and effective preventive maintenance and rehabilitation operations. Bridge engineers often perform scarification and overlay (SO) procedures on concrete bridge decks to minimize the corrosion of reinforcing steel due to chloride ingress. Given the need to develop guidelines for the initial timing of SO treatments, the specific objectives of this research were to collect information from several department of transportation (DOT) personnel about their SO procedures and, subsequently, to determine the recommended timing of initial SO procedures on concrete bridge decks for …

Detailed Seismic Evaluation Of Bridges On And Over The Parkways In Western Kentucky, Jian Xie, Issam E. Harik, Tong Zhao

Kentucky Transportation Center Research Report

This report outlines a rating system and details an evaluation procedure for the seismic evaluation of highway bridges. These processes are later used to investigate the structural integrity of selected highway bridges on and over the parkways in Western Kentucky. A total of 349 bridges were rated with the bridge ranking system, and 17 were selected for detailed seismic evaluation.

The capacity/demand ratio method developed by the Federal Highway Administration is employed for the detailed evaluation of bridges. The evaluation involves creating three-dimensional finite element models for all 17 bridges. Dynamic analysis is performed for a projected 250-year event. Among …

Equivalent Barge And Flotilla Impact Forces On Bridge Piers, Peng Yuan, Issam E. Harik

Kentucky Transportation Center Research Report

Bridge piers located in navigable inland waterways are designed to resist impact forces from barges and flotillas in addition to other design considerations (e.g., scour, dead and live loads, etc.). The primary design tool for estimating these forces is the AASHTO Guide Specification which provides a simple hand calculation method for determining an “equivalent impact force”. The simplicity comes at a cost of excluding the effect of the pier shape, impact duration, and interaction between barges in a flotilla. The objective of this report is to present a hand calculation method for determining barge or flotilla equivalent static impact forces …

Multi-Barge Flotilla Impact Forces On Bridges, Peng Yuan, Issam E. Harik, Michael T. Davidson

Kentucky Transportation Center Research Report

The current AASHTO equations for barge impact loads are based on scale models of barges, and may not accurately predict impact loads on bridge piers. The results of this study produce more realistic flotilla impact design loads, potentially leading to a reduction in construction costs of bridges over navigable waterways. The objectives of this study are: (1) To conduct theoretical finite element analysis on various types of flotillas impacting bridge piers. The flotillas and the respective barges will be of the type commonly traversing Kentucky’s waterways; and (2) To generate design equations for barge/flotilla impact loads. The study concludes the …

Impact Of Jet Grouting On The Lateral Strength Of Soil Surrounding Driven Pile Foundations, Matthew E. Adsero

Theses and Dissertations

Jet grouting was used to strengthen the soft soil surrounding the piles and the pile cap of two full-scale driven pile foundations. Soilcrete columns, created by jet grouting, were placed underneath the pile cap and surrounding the piles of the first foundation. Two rows of soilcrete columns were placed around the perimeter of one-side of the second. All of the jet grouting took place after construction of the pile caps. Laboratory testing of the soilcrete slurry showed the columns as having a design unconfined compressive strength of 550-650 psi, compared with the native soil strength of only 6-8 psi (850-1150 …

Compaction Of Mixtures Of Hard Rocks And Soft Shales And Non-Durable Shales Using Impact Compactors, Tommy C. Hopkins

Kentucky Transportation Center Research Report

Impact roller compaction has been used to improve embankment and highway subgrades in South Africa, Australia, Europe, and China and other areas of the world. In September of 2003, the International Technology Scanning Program, sponsored by the Federal Highway Administration (FHWA), the American Association of State Highway and Transportation Officials (AASHTO), and the National Cooperative Highway Research Program of the Transportation Research Board, identified this technology as one of several foreign technologies and innovations that could significantly benefit U.S. transportation systems. The technology was high-lighted at the Fifth International Conference on the Bearing Capacity of Roads and Airfields in 1998 …

Design And Evaluation Of An Open Combination Traffic/Bicycle Bridge Railing System, Jason A. Hascall, John R. Rohde, Dean L. Sicking, Karla A. Polivka, Ronald K. Faller, James C. Holloway M.S.C.E., E.I.T.

Nebraska Department of Transportation: Research Reports

No abstract provided.

The Structural Reliability Of Bridges Subject To Time-Dependent Deterioration, Colin C. Caprani, C. Mcnally, E. J. O'Brien, A. Bordallo-Ruiz

Conference papers

The reliability of the structural performance of any given structure is affected by both in-service loading and material deterioration due to environmental attack. They must be evaluated at any given time in order to compute lifetime probability of failure. This paper presents an innovative methodology to derive the structure lifetime load effect due to existing traffic using a statistical tool known as Predictive Likelihood. Loss of resistance due to corrosion originated by chloride ingression is also taken into account. Finally the lifetime probability of failure is evaluated via the application of a time-discretization strategy.

Fiber Optic Sensor : Monitoring Precast Beams, Purdue Ect Team

ECT Fact Sheets Archive

A new bridge over the Rio Puerco river, west of Albuquerque will be the first of its kind in the nation with built-in fiber-optic sensors to monitor stress in the bridge's girders. Known as "smart bridge" technology, the self-monitoring system offers many advantages over methods that rely largely on visual inspections.

Bridge Lock-Up Device System, Purdue Ect Team

ECT Fact Sheets Archive

The Colebrand Lock-up Device (LUD) provides additional substructure strength to resist seismic forces as a structural shock transmission unit for highway bridges. This system can provide a temporary rigid link between bridge structural members under seismic, braking, or other fast-acting type loads, while permitting slow thermal movements.

Long-Term Effects Of Super Heavy-Weight Vehicles On Bridges, Scott M. Wood, Necip Onder Akinci, Judy Liu, Mark D. Bowman

JTRP Technical Reports

A permit truck which exceeds the predefined limit of 108 kips is defined as a superload in Indiana. This study was conducted to examine the long-term effects of superload trucks on the performance of typical slab-on-girder bridges and to assess the likelihood of causing immediate damage. Typical steel and prestressed concrete slab-on-girder type bridges were analyzed using both beam line analysis and detailed finite element models. Furthermore, one prestressed concrete bridge and one steel bridge were instrumented using more than 50 sensors each. Strains and deflections were measured during a live load test, and each bridge was monitored for more …

Augusta Me: The New Bridge Begets A New Planned Neighborhood, Molly Pulsifer, Richard Barringer

Planning

Construction of a new Third Bridge over the Kennebec River in Augusta offered the prospect of a new and handsome gateway to the city. Further, the resulting change in traffic patterns offered the City the chance to plan for a pattern of development quite different from what the city had experienced for the past half-century. The case study describes the planning and construction of the new bridge and corridors that re-routed traffic out of Augusta’s downtown and older neighborhoods, and created the opportunity for planned development adjacent to the corridor created by the new bridge. It goes on to describe …

Finding The Distribution Of Bridge Lifetime Load Effect By Predictive Likelihood, Colin C. Caprani, E. J. O'Brien

Conference papers

To assess the safety of an existing bridge, the loads to which it may be subject in its lifetime are required. Statistical analysis is used to extrapolate a sample of load effect values from the simulation period to the required design period. Complex statistical methods are often used and the end result is usually a single value of characteristic load effect. Such a deterministic result is at odds with the underlying stochastic nature of the problem. In this paper, predictive likelihood is shown to be a method by which the distribution of the lifetime extreme load effect may be determined. …

Bridge Dynamics And Loading, Colin C. Caprani, Eugene O'Brien, Arturo Gonzalez, Yingyan Li, Paraic Rattigan, Niall Harris

Conference papers

Recent UCD research on dynamic bridge-truck interaction and bridge traffic loading in general is reported. The accuracy of bridge traffic load assessment has been significantly improved by identifying the differences in the sources of traffic loading on short- to medium-span bridges and treating them separately. It is shown that results can be significantly improved by treating 1-,2-,3- and 4-truck loading events separately. Gaps between trucks are also identified as a critical issue that strongly influences the frequency of key3-and 4-truck events. Trends in the dynamics of traffic loading are identified using simple force models on simply supported beams. It is …

Estimating Risk Of Failure Of Engineering Structures Using Predictive Likelihood, Colin C. Caprani, A. Bordallo-Ruiz, E. J. O'Brien

Conference papers

It has been common engineering practice to define characteristic values for loading and capacity of structures in order to assess the structural capacity of existing structures. This approach, yet practical and intuitive, lead to the comparison of deterministic values (characteristic values) that had to represent all the variability of the problem and is considered to be conservative, as usually loading is overestimated and capacity underestimated, yielding to calculations with high safety margins for the extreme events. Probabilistics methods have tried to overcom e this limitation by computing the overall probability of failure (Pf) for the lifetime of the structure, taking …

Determination Of Characteristic Bridge Daf Using Dynamic Finite Element Analysis Of Critical Static Loading Scenarios, Colin C. Caprani, Paraic Rattigan, Arturo Gonzalez, E. J. O'Brien

Conference papers

The development of accurate codes for the design of bridges and the evaluation of existing structures requires adequate assessment of site-specific heavy traffic loading and also the dynamic interaction that may occur as this traffic traverses the structure. Shortcomings in current design codes occur due to the relatively independent manner in which critical static loading values and the corresponding allowance for dynamic amplification factor (DAF) are obtained. It is important that an approach is adopted that allows for the reduced probability of both high static loading and high dynamic amplification occurring simultaneously. Consideration of only relevant critical loading events will …

Study Of Same-Lane And Inter-Lane Gvw Correlation, Bernard Enright, Eugene J. O'Brien, Colin C. Caprani

Conference papers

The methodology used is to generate a number of years of simulated traffic and to use extreme value statistics to predict more accurately the characteristic loading for a given bridge. The parameters and probability distributions used in the Monte Carlo simulation must be based on observed sample traffic data. Some previous studies have made unsubstantiated assumptions regarding correlation between the Gross Vehicle Weights (GVW) of trucks in the same lane, or between trucks in adjacent, same-direction lanes. For this paper, an extensive database of Dutch Weigh-in-Motion data is analysed. Data are collected from two same-direction lanes and are time-stamped to …

Statistical Computation For Extreme Bridge Traffic Load Effects, Colin C. Caprani, E. J. O'Brien

Conference papers

The maintenance of highway infrastructure constitutes a major expenditure in many countries. This cost can be reduced significantly by minimizing the repair or replacement of highway bridges. In the assessment of existing bridges, the strength estimate tends to be more accurate than that of traffic loading, due to the more variable nature of loading. Recent advances in the statistical analysis of highway bridge traffic loading have resulted in more accurate forecasts of the actual loading to which a bridge is subject. While these advances require extensive numerical computation, they can significantly improve the accuracy of the calculation. This paper outlines …

Shear Repair Of P/C Box Beams Using Carbon Fiber Reinforced Polymer (Cfrp) Fabric, Jim W. Simpson Ii, Issam E. Harik, Choo Ching Chiaw

Kentucky Transportation Center Research Report

The report documents the retrofit work carried out on the KY3297 Bridge over Little Sandy River in Carter County, Kentucky. Field investigation and evaluation revealed that the bridge superstructure was deficient in shear. The repair work was carried out using externally bonded carbon fiber reinforced polymer (CFRP) fabric system. The repair, using externally bonded fiber system, offers the following benefits: (1) the use of light construction equipment, hand kits and tools, (2) minimal traffic disruption as all lanes were open to traffic while work was being performed underneath the bridge, and (3) cost saving; the cost for the repair and …

Jointless And Smoother Bridges: Behavior And Design Of Piles, Robert J. Frosch, Voraniti Chovichien, Katrinna Durbin, David Fedroff

JTRP Technical Reports

Integral abutment bridges have been used in the United States for decades. By eliminating expensive expansion joints, the piles supporting the end bent accommodate the total thermal movement of the bridge. Currently, integral bridges are designed based upon experience, and a rational design specification has not been developed. Furthermore, the interaction of the abutment, pile, and soil remains uncertain. A better understanding regarding the behavior of this system is needed. The objective of this research is to evaluate the behavior of the integral abutment-pile system and evaluate any limitations of its use. To achieve this objective, two phases of research …

Fatigue Of Older Bridges In Northern Indiana Due To Overweight And Oversized Loads, Volume 1: Bridge And Weigh-In-Motion Measurements, James A. Reisert, Mark D. Bowman

JTRP Technical Reports

This report is the first of a two-volume final report presenting the findings of the research work that was undertaken to evaluate the fatigue behavior of steel highway bridges on the extra heavy weight truck corridor in Northwest Indiana. The purpose of the study was to evaluate the type and magnitude of the loads that travel along the corridor and then assess the effect of those loads on the fatigue strength of the steel bridge structures on the corridor. This volume presents the results of the experimental field study conducted to evaluate the load and load effects on one steel …