Civil and Environmental Engineering Commons^™

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Ultrafast Belite (Β-C2s) Production Using Biofuel-Based Combustion Synthesis, Shubham Agrawal, Sayee Srikarah Volaity, Oluwadamilare Charles Adesina, Bryan K. Aylas-Paredes, Taihao Han, Srinivas Kilambi, Aditya Kumar, Narayanan Neithalath

Materials Science and Engineering Faculty Research & Creative Works

This study presents a novel low-temperature, combustion synthesis (CS) approach for the rapid production of belite-rich cements. CS leverages the exothermic heat released from the combustion of biofuels such as lignin and/or biomass, intermixed with pelletized limestone and quartz. At an imposed furnace temperature of ∼700°C (as opposed to 1200°C–1300°C required in a conventional kiln), the source materials are rapidly transformed to belite, resulting in energy, emissions, and economic benefits. This work explores the influence of various process parameters, viz., fuel types and contents, airflow rate, porosity, holding temperature, and holding time on the efficiency of CS-based belite synthesis. Through …

Leaning Pine Arboretum Gazebo, Carson C. Henry

Construction Management

The Leaning Pine Arboretum gazebo provides an aesthetic relaxation space for visitors to the arboretum as well as being a functional structure for faculty as a future event space. This gazebo replaces an existing one, revitalizing the space in conjunction with the arboretum’s planned growth over the coming years. There were many challenges throughout the construction process including permitting issues, design complexities, and coordination with architects and engineers. Persevering through these taught a great deal about project management, the construction industry, and the importance of teamwork. The structure is a total rejuvenation of the prior structure; it is now stronger, …

Developing A 4d Logistics Educational Module With Cmbuilder, Misael Gonzalez Ramirez

Construction Management

The increasing adoption of Building Information Modeling (BIM) in the construction industry has led to a need for its increasing integration into construction management education. While existing curriculum covers various BIM applications, there is often a gap in in-depth instruction on BIM-based site logistics planning. This paper details the development of an educational module designed to address this gap, focusing on 4D site logistics and phasing using cmBuilder. The module aims not only to provide students with technical software skills but also to equip them with practical skills in visualizing, planning, and communicating complex construction site logistics. Through a series …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Corrosion Of Pipes In Soil Under Cathodic Protection, Ashley Chow

Williams Honors College, Honors Research Projects

This research project focuses on understanding how various soil properties affect the corrosion of buried pipelines that are protected by cathodic protection (CP) systems. Specifically, the study seeks to evaluate key soil characteristics, including resistivity, moisture content, and pH levels to determine their influence on the efficiency of CP systems in mitigating corrosion. Through controlled laboratory experiments, carbon steel specimens were exposed to a range of simulated soil conditions to mimic real-world environments. Corrosion rates were assessed using advanced electrochemical techniques, such as linear polarization resistance (LPR) and Tafel slopes, along with traditional mass loss methods. The primary objectives of …

Software Literacy In Construction, Aidan Cazares

Williams Honors College, Honors Research Projects

The construction industry increasingly relies on software like Bluebeam Revu for their quantity takeoff, document management, and collaboration needs. This project will outline pertinent information obtained through their Bluebeam professional training program and reflect it with a detailed estimate of a real life construct project.

Passive Phosphorus Filtering System Design, Ryan T. Bailey

Williams Honors College, Honors Research Projects

The objective of this project is to find an efficient way to remove phosphorus from surface water through passive filtration. Specifically, the project will focus on the upper Cuyahoga River. Ongoing research being conducted by Dr. Teresa Cutright from The University of Akron and Jessica Glowczewski from the City of Akron’s Watershed Division serves as a basis for this project.

Fertilizers used in agriculture are often washed off by rainfall and enter the groundwater and nearby streams. The phosphorus contained in the fertilizer can be harmful to the environment by increasing the frequency of large algal blooms. To reduce the …

Structural Analysis And Design Methodologies Of Roller Coasters, Benjamin Komar

Williams Honors College, Honors Research Projects

This project explores the structural analysis behind the design of roller coaster tracks and supports as practiced by modern engineers. It also examines various roller coaster design methods currently in use. This research will be used to craft a detailed explanation of the roller coaster design process. Additionally, a 3D model of a roller coaster was developed based on the researched design procedures, featuring three track sections with different loading conditions to create a supporting structure for 2D truss analysis. The results of the truss analysis were then compared to those obtained using RISA-3D, a finite element structural design software.

Indiana Interstate Speed Profiles 2020-2024, Rahul Suryakant Sakhare, Jairaj Desai, Deborah Horton, Darcy M. Bullock

Indiana Mobility Reports

This report presents a graphical summary of monthly mile-hours of congestion across the 8 Indiana interstates (I-64, I-65, I-69, I-70, I-74, I-94, I-465, and I-469) and the Indiana Toll Road (I-90) analyzed longitudinally over the last five years from January 2020 to December 2024. It is a continuation of speed profile summaries that are published in previous years. Such systemwide interstate performance measures provide important information for decision makers to plan capital projects and assess operations.

Hours of operation by speed bins (0 to 14 mph, 15 mph to 24 mph, 25 mph to 34 mph, 35 mph to 44 …

Crawfordsville District Interstate Speed Profiles: April 2020–March 2025, Rahul Suryakant Sakhare, Jairaj Desai, Deborah Horton, Darcy M. Bullock

Indiana Mobility Reports

This report presents a graphical summary of monthly mile-hours of congestion across the three interstates (I-65, I-70, and I-74) in INDOT’s Crawfordville District analyzed longitudinally over the last five years from April 2020 to March 2025. It is a continuation of speed profile summaries that are published in previous years. Such systemwide interstate performance measures provide important information for decision makers to plan capital projects and assess operations.

Hours of operation by speed bins (0 to 14 mph, 15 mph to 24 mph, 25 mph to 34 mph, 35 mph to 44 mph, 45 mph to 54 mph, 55 mph …

Build Digital Annual Survey 2024 Results, Clare Eriksson, Robert Moore, Bilal Succar

Reports

The Build Digital Annual Survey 2024 presents a sector-wide snapshot of digital adoption and transformation across Ireland’s construction and built environment sector. Based on 137 responses, the report shows that most participating organisations have begun their digital transformation journey, with expected benefits including improved accuracy, operational efficiency, quality, cost reduction, and faster clash resolution. The findings indicate widespread use of common digital deliverables and increasing awareness of ISO 19650, CDEs, OpenBIM, and CWMF BIM requirements. However, the report also identifies persistent challenges, including skills gaps, uneven training provision, limited digital competence, and variable implementation of BIM requirements across public and …

Using The Historical Equity Action Lens (Heal) To Identify And Remedy Transportation Inequities From The Akron Innerbelt Project, Olivia Lane

Williams Honors College, Honors Research Projects

This project will utilize the Historical Equity and Action Lens (HEAL) to address transportation inequities in marginalized communities by incorporating historical and cultural insights into data collection and analysis. Specifically, the project will focus on the Akron Innerbelt, an infamous highway project that significantly impacted historically Black neighborhoods. By examining the historical, economic, and social context of the Innerbelt, the project will identify the project's long-term impacts Akron communities. The goal is to use this knowledge to inform improve transportation equity in the affected areas by developing a plan for the Innerbelt since its vacancy in 2016. The project will …

Artificial Intelligence’S Role And Impact On The Engineering Discipline, Andrew Angelini

Williams Honors College, Honors Research Projects

The purpose of this Honors Research project was to explore the impact of Artificial Intelligence (AI) on the Engineering Discipline as a whole. Specifically, civil engineering’s discipline of transportation was used to display the effectiveness of AI in engineering. This discipline was used due to its wide use in engineering and overall designs that can be created within this discipline. These designs include maintenance of traffic plans, engineering plan sets, horizontal and vertical curve design, intersection design, traffic signaling, highway material design, and phasing of intersections and traffic accounting for pedestrians. Through similar prompts that were given to a publicly …

The Towering Inferno: Art, Policy, And Legacy, Charles R. Jennings

Publications and Research

The Christian Regenhard Center for Emergency Response Studies, leveraging the expertise of its faculty, staff, Advisory Board and colleagues, has consistently programmed activities focused on high-rise fire safety. The upcoming 50^th anniversary of the film The Towering Inferno was an inspiration.

We decided this would be more lighthearted and less purely technical than many of our events. We wanted to consider both the film, and use it to reflect on the state of fire safety in tall buildings in New York City.

Of course it does not escape us that the topic of fire safety is a serious one, …

Pla Polymer Binder In Core Production - Influence On Final Casting Dimensions, Artur Soroczyński, Krzysztof Rechowicz

Virginia Digital Maritime Center (VDMC) Faculty Publications

The foundry industry is seeking an ecological alternative to synthetic molding resins. This study evaluates the technological properties of core sands bonded with biodegradable polylactide (PLA). Cores prepared on a 2% quartz sand matrix were subjected to casting processes using two alloys with extremely different pouring temperatures: gray cast iron (approx. 1200 °C) and AK11 silumin (approx. 710 °C). The research methodology included macroscopic assessment, dimensional analysis using 3D scanning (GOM Inspect), and qualitative knock-out assessment supported by numerical temperature field simulation. The results showed that the high crystallization temperature of cast iron leads to complete thermal degradation of the …

Analysis Of Lava Flow Paths Using Remote Sensing And Geomorphological Techniques, Oluwatosin Oluyemisi Ayo

Dissertations, Master's Theses and Master's Reports

Lava flows have severe impacts on the Earth’s surface, communities, and natural habitats. Accurate modeling of lava flow paths is crucial for volcanic hazard assessment and risk mitigation. This research integrated remote sensing, geographic information systems, geomorphological techniques, and hydrologic analysis to numerically determine the optimal ground sample distance (GSD) of digital elevation models (DEMs) for delineating lava flow paths. Two volcanic regions were analyzed: the Afar Region of Ethiopia (Alu, Dalaffilla, and Erta Ale volcanoes) and the Reykjanes Peninsula of Iceland (Fagradalsfjall volcano). Forward and backward modeling methods were used to simulate potential lava flow paths. Remote sensing data, …

Transport Of Nutrients By Overland Flow On Sites Containing Beef Cattle Manure, John E. Gilley, Ryan P. Mcgehee, Kenneth M. Wacha

Department of Agricultural and Biological Systems Engineering: Faculty Publications

In an inductive metastudy, we investigated the effects of varying rates of overland sheet flow on the transport of phosphorus (P) and nitrogen (N) from sites containing beef cattle manure. The analyzed data were collected during previously reported field rainfall simulation investigations conducted on cropland sites and a beef cattle feedlot in the US state of Nebraska. During the experiments, inflow was incrementally added to the top of the experimental plots to simulate runoff rates occurring at greater downslope distances. Runoff rates on the experimental plots ranged from 2.9 to 22.9 Lmin⁻¹, and the maximum equivalent downslope distances …

Crop2cloud Platform: Real-Time Data Integration For Agricultural Water Monitoring, Bryan Nsoh, Abia Katimbo, Kendall Dejonge, Wei-Zhen Liang, Hongzhi N. Guo, Yufeng Ge, Derek M. Heeren, Yeyin Shi, Xin Qiao, Daran R. Rudnick, Hope Njuki Nakabuye, Birru Girma, Isa Kabenge, Joshua Wanyama

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Efficient water management is vital for sustainable agriculture, yet integrating real-time data for precise irrigation remains a challenge. This study designed the Crop2Cloud (C2C) platform, a system that leverages advanced sensors using Internet of Things (IoT), edge and cloud computing techniques, and computed Water Stress Indices (WSIs) and machine learning models (i.e., fuzzy logic), to provide scalable and real-time irrigation decisions. The C2C platform aggregates several data including Volumetric Water Content (VWC) from TDR sensors (Acclima Inc., US) installed at four multiple depths, canopy temperatures (Tc) measured by Infrared Radiometers (IRTs) (Apogee Instruments, US), as well as weather information and …

Behavioral Insights Impacting Preweaning Mortality, Md Towfiqur Rahman, G. A. Rohrer, S. R. Sharma, Y. Shi, S. M. Leonard, Tami M. Brown-Bandl

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Conclusions

This study investigated the average time spent on posture behaviors (lying, kneeling, sitting, standing) of sows by analyzing the effects of time segments, farrowing crate types, parity, heat lamp configurations, and mortality groups. Sow posture behaviors were significantly influenced by mortality, parity, crate type, heat lamps, and day category. High mortality sows spent less time lying and more time standing events. Parity 1, 2, 3 sows were more active, spending more time kneeling in transitions, lying, and sitting events. Sows in TSL crate had longer lateral right lying and standing events, while ESCSL crates sows had longer sitting events. …

Firelog: An Open-Source, Low-Cost System For Temperature Logging During Wildland Fires With High Spatial And Temporal Resolution, Nipuna Chamara, Yufeng Ge, Sabrina E. Russo

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Measuring flame, air, and soil temperatures during wildland fires, including wildfires and controlled burns in land management contexts, is crucial for research and applications in fire ecology, safety, and management in a wide array of ecosystems, from grasslands to forests. However, open-source and commercial systems are needed for measuring and logging flame and air temperatures that are user-friendly, economical, modular, and customizable. This paper details the design, development, and validation of the FireLog system. Laboratory validation experiments demonstrated high measurement accuracy, with a minimum coefficient of determination (R2) of 0.98 and the highest observed root mean square error (RMSE) of …

Cover Crops Can Reduce Greenhouse Gas Emissions From No-Till Maize In Southern Brazil: Insights From A Long-Term Field Experiment, Guilherme Rosa Da Silva, Adam J. Liska, Cimélio Bayer

Adam Liska Papers

Brazil is one of the countries that has the most agricultural area under no-till (NT) management. This research study aims to evaluate life-cycle greenhouse gas (GHG) emissions from maize (M) grain production in agroecosystems that used different cover crops under NT management in southern Brazil. The data for this study were from a long-term 41-year field experiment in southern Brazil. The long-term experiment evaluated the effects of fallow (F) and cover crops (oat (O), vetch (V), cowpea (B), pigeon pea (P), and lablab (L)) on nitrous oxide and methane emissions and soil carbon (C) sequestration in maize agroecosystems. Five cropping …

Scalable Machine Learning Framework For Adaptive Irrigation Management Of Maize And Soybean In The U.S. Midwest, Precious N. Amori, Derek M. Heeren, Yeyin Shi, Eric Wilkening, Ivo Z. Goncalves, Guillermo R. Balboa, Daran R. Rudnick, Abia Katimbo, Randall S. Ritzema

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Conventional soil water balance (SWB) irrigation scheduling tools, such as FAO-56-based Spreadsheets and the Spatial Evapotranspiration Modeling Interface (SETMI), rely heavily on manual inputs and periodic field measurements, leading to delayed recommendations and missed opportunities to prevent crop stress. More critically, these tools lack the computational scalability and adaptability to leverage the high-frequency, high-volume datasets now available through modern sensing technologies. As precision irrigation increasingly depends on integrating spatially and temporally nuanced field information, there is a pressing need for decision-support systems that can process Big Data efficiently and respond in real-time. To overcome these limitations, we developed and validated …

Cognitive Map Generation For Vision And Language Navigation, Alexander Sandoval Mesa

Dissertations and Theses

Visual-Language Navigation (VLN) presents significant challenges for autonomous agents, such as robots and virtual assistants, particularly in complex, dynamic environments where the seamless integration of visual perception and natural language understanding is critical. Traditional VLN systems often struggle with effectively aligning language instructions and visual scene understanding, limiting their adaptability and navigation efficiency.

This thesis proposes a novel Cognitive Map-based framework that addresses these challenges by transforming natural language navigation instructions into structured graph representations. The Cognitive Map consists of nodes representing waypoints, landmarks, decision points, and edges encoding spatial relationships and navigational actions. These maps are generated using Large …

Data Driven Bridge Deck Deterioration Modeling And Maintenance Intervention Scheduling, Deepak Kumar

Dissertations and Theses

Majority of over 617,000 bridges across the United States are significantly impacted by environmental factors, aging materials, and heavy traffic loads. According to the 2021 Infrastructure Report, nearly 231,000 bridges require repair or preservation work, with 46,154 (7.5%) being classified as structurally deficient, thereby posing risks for mor than 178 million daily trips across these bridges. Despite recent improvements, 42% of U.S. bridges are at least 50 years old, underscoring an urgent need for increased investment to meet repair demands. The nation’s backlog of bridge repairs is estimated at $125 billion, with a 58% increase in annual spending required to …

Deep Learning Architectures For Improving Weather Research And Forecasting (Wrf) Precipitation Estimates And Landslide Susceptibility Mapping: A Case Study Of Puerto Rico, Said A. Mejia Manrique

Dissertations and Theses

Precipitation is a critical factor in the Earth’s hydrological cycle and has a profound impact on various environmental and socioeconomic systems, including management of water resources, flood forecasting, and the evaluation of natural hazards, particularly those associated with rainfall-induced landslides. For the latter, obtaining precise precipitation estimates is essential, as intense rainfall events can trigger landslides that pose significant risks to human life, infrastructure, and ecosystems, particularly in mountainous regions. Puerto Rico (PR), with its mountainous terrain, tropical climate, and vulnerability to hurricanes, provides a unique environment for studying precipitation patterns and the need for accurate rainfall estimates. The complex …

A Review Of Infrared Thermography Applications For Civil Infrastructure, Prabal Shrestha, Onur Avci, Sahabeddin Rifai, Feras Abla, Michael Seek, Karl Barth, Udaya Halabe

Engineering Technology Faculty Publications

Civil infrastructure is continuously subject to aging and deterioration due to multiple factors, which lead to a decline in performance and impact structural health. Accumulated damage on structures increases operational costs and poses significant risks to public safety. Effective maintenance, repair, and rehabilitation strategies are needed to ensure civil infrastructure’s overall safety and reliability. Non-Destructive Evaluation (NDE) methods are utilized to assess latent damage and provide decision-makers with real-time information for mitigating hazards. Within the last decade, there has been a significant increase in the research and development of innovative NDE techniques to improve data processing and promote efficient and …

Evaluating The Effectiveness Of Stay-In-Place Forms To Improve The Tosional Stability Of Box Beam Bridges During Erection, Karl E. Barth, Michael W. Seek, Gregory K. Michaelson, Dimitra Pyrialakou, Brook T. Woldegabriel

Engineering Technology Faculty Publications

Cold-formed tub girders provide an effective steel solution for short-span bridges. The girders are often delivered with an open top with stay-in-place forms installed on site. Walkways may be installed to the side of the girder that can induce significant torsion rotations in the open cross section. Full scale tests on girder specimens have shown that installing one or two panels of stay in place forms at the ends of the girder can significantly reduce the torsion rotation of the girder by providing warping resistance. Cantilever tests on the stay in place forms are performed to investigate the influence of …

Advancing Sustainability In Civil Engineering Technology Through The Engineering For One Planet Framework, Dalya Ismael, Vukica M. Jovanovic, Murat Kuzlu, Charles Lowe, Lisa Bosman

Engineering Technology Faculty Publications

As global environmental challenges intensify, integrating sustainability into engineering technology education is increasingly critical. Yet, many programs lack comprehensive methods to embed sustainability principles, leaving graduates underprepared to address real-world environmental issues. Courses on sustainability often approach it in isolated or superficial contexts, unable to capture its complexity. The purpose of this study is to showcase one approach for embedding the Engineering for One Planet (EOP) framework into the Sustainable Building Practices course within the Civil Engineering Technology Department. The newly developed curriculum integrated learning outcomes from three EOP topics: Environmental Impact Assessment, Materials Selection, and Systems Thinking. Students were …