Civil and Environmental Engineering Commons^™

On The Feasibility Of Ultrasonic Full Waveform Evaluation With Changing Testing Conditions For The Quality Control Of Manufacturing Parts, Simon Schmid, Thomas Schumacher, Christian U. Grosse

Civil and Environmental Engineering Faculty Publications and Presentations

Fast volumetric non-destructive testing methods are needed, especially for quality control in manufacturing lines. Ultrasonic testing with full waveform evaluation is a promising method for this. However, changes in coupling conditions or environmental factors can significantly alter the ultrasound signal, sometimes more than actual defects. This study investigates the effect of various factors on the ultrasound signal based on a Monte Carlo study with wavefield simulations. The test specimens comprise aluminium plates with holes of varying sizes and positions. Using both experimental as well as simulated data, the performance of two commonly used comparison metrics, namely the R2 score and …

Performance Enhancement Of A Solar-Driven Dcmd System Using An Air-Cooled Condenser And Oil: Experimental And Machine Learning Investigations, Pooria Behnam, Abdellah Shafieian, Masoumeh Zargar, Mehdi Khiadani

Research outputs 2022 to 2026

Solar-driven direct contact membrane distillation systems (DCMD) are disadvantaged by low freshwater productivity and low gain-output-ratio (GOR). Consequently, this study aims to achieve two primary objectives: i) improving the solar DCMD performance, and ii) harnessing machine learning models for precise and straightforward modeling of the solar DCMD system. To achieve these goals, a novel solar DCMD system powered with oil-filled heat pipe evacuated tube collectors (HP-ETCs) and equipped with an air-cooled condenser was used for the first time. The system was evaluated under eight different scenarios covering both its energy and economic performances. The performance prediction of three different machine …

Forecasting Future Research Trends In The Construction Engineering And Management Domain Using Machine Learning And Social Network Analysis, Gasser G. Ali, Islam H. El-Adaway, Muaz O. Ahmed, Radwa Eissa, Mohamad Abdul Nabi, Tamima Elbashbishy, Ramy Khalef

Civil Engineering Faculty Publications

Construction Engineering and Management (CEM) is a broad domain with publications covering interrelated subdisciplines and considered a key source of knowledge sharing. Previous studies used scientometric methods to assess the current impact of CEM publications; however, there is a need to predict future citations of CEM publications to identify the expected high-impact trends in the future and guide new research efforts. To tackle this gap in the literature, the authors conducted a study using Machine Learning (ML) algorithms and Social Network Analysis (SNA) to predict CEM-related citation metrics. Using a dataset of 93,868 publications, the authors trained and tested two …

Education And Training Networks, Ken Thomas, Robin Stubbs, Emily Shakespeare

Tools

Education And Training Networks Inventory is a review of relevant network in Ireland and the EU.

Assessment Of Engineering Performance And Environmental Impacts Of High Reclaimed Asphalt Pavement (Rap) Asphalt Mixtures In Flexible Pavements, Ibrahim A.I.E. Elnaml

LSU Doctoral Dissertations

Due to the critical role of asphalt pavements in national infrastructure development, there is a pressing need to investigate more sustainable materials and approaches. The use of natural aggregates and asphalt binders in asphalt pavement presents sustainability challenges due to the depletion of finite resources. Recycling Asphalt Pavement (RAP) offers a promising sustainable solution by substituting virgin aggregates and asphalt binders with recycled ones. However, increasing RAP contents in asphalt mixtures (>25%) can lead to premature cracking, insufficient durability, and limited longevity due to the presence of aged RAP-asphalt binder. To address these concerns, the application of novel recycling …

An Architectural Approach To Neighborhood Design In The Quarry Road Informal Settlement In Durban, Viloshin Govender, Ameen Shaikjee

CSID Journal of Infrastructure Development

Informal settlements, often characterized by inadequate infrastructure, housing, and services, are a significant urban challenge in the global South. Creating well-functioning and supportive neighborhoods within these settlements is crucial for improving the living conditions and livelihoods of those living there. This paper explores the strategies and principles of creating neighborhoods in informal settlements that promote community empowerment, social cohesion, and sustainable development. Conventional top-down development approaches often fail to address these settlements' unique needs and dynamics. In contrast, a bottom-up approach empowers residents, fosters community engagement, and promotes sustainable development. This paper explores how architecture can respond to the needs …

Assessing The Characteristics Of Coastal Neighbourhoods That Influence Flood Susceptibility In Kosofe, Nigeria, Saudat O. Ajijola, Funmilayo M. Adedire, J A. Fadamiro

CSID Journal of Infrastructure Development

As climate change continues to exacerbate weather patterns, flood susceptibility has become an increasingly pressing global concern. The susceptibility to floods is influenced by many contextual factors; as such, characterizing coastal neighbourhoods for the purpose of articulating susceptibility pathways is crucial for developing appropriate physical planning policies. The specific research objective seeks to assess the dimensions of neighbourhood characteristics that influence flood susceptibility in Kosofe, a suburban coastal community in Lagos, Nigeria. The data used were based on primary and secondary sources. Using a systematic sampling method, 324 respondents participated in the field survey. The result of the descriptive statistics, …

Evolving Hangwuran City Development Model Through Partial Least Square Approach In North-Central Nigeria, Samuel Medayese, Hangwelani H. Magidimisha-Chipungu, Lovemore Chipungu

CSID Journal of Infrastructure Development

The need for a paradigmatic shift in city development ideology has become increasingly evident over the years. In response to this need, the Hangwurian City Development Model was developed to establish a connection between the concepts of environmental awareness, urban governance, and management. This model also integrates sustainable urban development, urban liveability, and inclusive physical development. The research sets a critical objective of analyzing the significant levels of various indicator variables. The exploratory research utilized partial least squares (PLS) via SmartPLS to evaluate the variables, collecting quantitative data through the open data toolkit from three selected cities: Lokoja, Minna, and …

Neighbourhood Planning: Reminiscence Towards Liveable Communities, Bolanle Wahab, Waheed Kadiri, Ayobami Popoola, Bamiji Adeleye, Robert A. Dwamena

CSID Journal of Infrastructure Development

Urbanisation remains a topical discussion across the globe. According to the United Nations (2022), 68% of the world's population will be absorbed in urban areas by 2050. The envisaged rapid urbanisation in cities by 2050 is believed to be accompanied by various planning problems, which include accelerated climate change, urban slums, urban sprawl, poor sanitation, inadequate infrastructure, overcrowding, housing deficiency and transportation issues. To mitigate these planning problems, the role of effective urban planning cannot be overemphasised. Urban planning provides a pathway for overcoming the various challenges posed by urbanisation both in the present and in the future.

Urban planning …

Urban Expansion And Loss Of Watershed Of Eleyele Dam In Ibadan, Nigeria, Samson A. Adejumo, Solomon Osunwale

CSID Journal of Infrastructure Development

The study examined human activities contributing to the depletion of the Eleyele watershed. The activities have grown over time due to urban expansion through population growth and land and space requirements, resulting in rapid land use and land cover change. The study sourced both quantitative and qualitative data. A total of 247 pre-tested questionnaires were administered to randomly selected residents in the four communities (Eleyele, Ijokodo, Awotan, and Idi Osan) abutting the Eleyele watershed. In-depth interviews were conducted with the heads of Eleyele Waterworks, the Forestry Department, and the Oyo State Ministry of Agriculture and Natural Resources. We used Remote …

Condition Of Drainage System And Its Impact On The Residents Of Mowe, Ogun State, Nigeria, Ayodeji Olusola Ajayi, Testimony Ayomide Oladiran, Ismail Adedapo Oyerinde, Aderonke Olufunmi Ajayi, Adonis Busuyi Fakanlu

CSID Journal of Infrastructure Development

This study examines the impacts of drainage infrastructure conditions on Mowe, Ogun State, residents. The study used a quantitative research design, using a systematic random sampling technique to select ten (10) residential estates (three public-owned and seven privately owned) in the study area. In all, 107 residents were sampled using a structured questionnaire. The data collected was analysed using descriptive statistics. Based on the findings of this study, it was evident that the surface drainage system, mainly constructed with sandcrete blocks, was predominant in the study area. The result established that the drainage's minimum height in the study area was …

Partnership And Coalition Efforts For Community-Based Research: Towards A Liveable Urban And Rural Settlement In Kwazulu-Natal, Sibongile A. Ngcobo, Nene E. Khalema, Tawanda Makusha

CSID Journal of Infrastructure Development

This paper examines the role of community partnerships and coalitions in the intricate and constantly evolving dynamics of communities in KwaZulu-Natal, South Africa. Various aspects of the community context, such as socioeconomic conditions, geography, environmental factors, demographics, community politics, and cultural norms, often influence these community partnerships and coalitions. This study adopted the Community Coalition Action Theory as an organisational framework to examine the efforts of coalitions and partnerships in community-based research. The research applied a mixed-methods approach. This included a survey and individual interviews within the research organisation responsible for multiple community-based projects in rural and urban areas of …

Land Surface Temperature And Landuse/ Land Cover Change Variability Using Remotely Sensed Data For Sub-Urban Settlements In Osun State, Nigeria, Saeed K. Ojolowo, Abiodun A. Audu, Charles O. Olatubara, Olusiyi Ipingbemi, Olaitan O. Odunola, Olaide J. Omirin, Oluwasinaayomi F. Kasim

CSID Journal of Infrastructure Development

Land surface temperature (LST) is an indispensable factor in studying urban climate. Ground-based measurements have been employed to quantify LST and Land Use/Land Cover Change (LULC). However, due to advancements in space technology and extensive spatial coverage, remote sensing techniques are increasingly being used to measure the intensity of LST and LULC dynamics, owing to the availability of enhanced satellite-based thermal observations of the Earth. The climatic conditions over a medium-sized city could be improved by understanding the interplay of LST and LULC. In this study, we estimated LST based on Landsat bands 4 and 5 for 1990 and 2000, …

Liveable Communities: A Case Study Of Availability, Proximity, And The Quality Of Critical Infrastructure In Colombo, Srilanka, Maheshi Tennakoon, Udayangani Kulatunga

CSID Journal of Infrastructure Development

The concept of livable communities has become increasingly significant in regional planning, aiming to improve the quality of life for residents. Despite continued investment in critical infrastructure in developing countries, the enhancement of livability has not kept pace with infrastructure development. This study investigates the impact of crucial infrastructure on community livability, utilizing a holistic single case study approach with Colombo as the case study. The relationship between critical infrastructure development and urban livability serves as the unit of analysis. Data were collected through semi-structured interviews with ten subject matter experts and analyzed using manual content analysis. The research finds …

Socio-Economic Effects Of Orisumbare Sawmilling Industries On The Residents Of Ikire, Irewole Local Government Area Osun-State, Nigeria, Umar Usman Jimoh, D R. Ogungbemi

CSID Journal of Infrastructure Development

The study examined the socio-economic effects of the Orisumbare sawmill industry on the residents of Ikire, Irewole local government area of Osun State. The objectives of the study include, examination of the socio-economic characteristics of the respondents, the positive effects of industry on the residents, the negative impacts of industry on the residents, and the perceived environmental-induced diseases caused by industrial activities. A case study research design was adopted, while both primary and secondary data were utilised. A multistage sampling technique was used, in which a buffer zone of 900m radius was made to delineate the zone of industries’ influence. …

Analysis Of The Effects Of Service Delivery On The Wellbeing Of Internally Displaced Persons (Idps) In Federal Capital Territory (Fct), Abuja, Olusegun O. Idowu, Valda Martins, Ndako B. Santali, Jonathan U. Adama, Adekunle S. Adeogun, Gideon Danlami

CSID Journal of Infrastructure Development

The provision of services, encompassing substandard medical facilities, inadequate housing conditions, limited access to electricity, insufficient recreational amenities, and the absence of potable water supply, has emerged as a significant impediment confronting Internally Displaced Persons (IDPs) both domestically and globally. The present investigation sought to evaluate the impact of service delivery on the welfare of IDPs residing in the Federal Capital Territory (FCT), Abuja. The objectives of this inquiry were to assess the socioeconomic attributes of the IDPs, scrutinize the types and efficacy of service delivery within the IDP camps, and appraise the consequences of service delivery on the well-being …

Utilizing Hybrid Machine Learning Techniques And Gridded Precipitation Data For Advanced Discharge Simulation In Under-Monitored River Basins, Reza Morovati, Ozgur Kisi

Civil and Environmental Engineering Faculty Publications

This study addresses the challenge of utilizing incomplete long-term discharge data when using gridded precipitation datasets and data-driven modeling in Iran's Karkheh basin. The Multilayer Perceptron Neural Network (MLPNN), a rainfall-runoff (R-R) model, was applied, leveraging precipitation data from the Asian Precipitation—Highly Resolved Observational Data Integration Toward Evaluation (APHRODITE), Global Precipitation Climatology Center (GPCC), and Climatic Research Unit (CRU). The MLPNN was trained using the Levenberg–Marquardt algorithm and optimized with the Non-dominated Sorting Genetic Algorithm-II (NSGA-II). Input data were pre-processed through principal component analysis (PCA) and singular value decomposition (SVD). This study explored two scenarios: Scenario 1 (S1) used in …

Electrochemical Phosphorus Recovery From The Anaerobically Digested Sludge: Mechanism, Performance, Application, And Solids Disposal, Zixuan Wang

McKelvey School of Engineering Graduate Student Theses & Dissertations

Phosphorus (P) is life’s bottleneck element and an essential nutrient for food production. However, phosphate rock is a non-renewable resource and its geological distribution is highly uneven, making P recovery a crucial step for a circular economy. Approximately 55% of mined phosphorus ends up in centralized wastewater treatment plants (WWTPs), where up to 90% is captured in the sludge. This sludge, treated in anaerobic digesters to produce anaerobically digested sludge (ADS), emerges as a viable secondary source for phosphorus recovery. Recovering phosphorus from ADS typically involves leaching and separation. Leaching mobilizes phosphates from sludge solid phase into a liquid phase, …

Use Of Mathematical Skills For Technical Condition Assessment Of Power Autotransformers, Dilafruz Rustamjon Qizi Abdullabekova, Nurali Berdiyorovich Pirmatov

Technical science and innovation

In this paper, we review innovative approaches to assess the technical condition of autotransformers using mathematical methods. The main purpose of these methods is to increase the efficiency of diagnostics and prevent possible failures in power systems. The developed mathematical expression is based on complex data analysis, application of statistical methods and machine learning technologies. This makes it possible to achieve more accurate and earlier detection of potential problems. As a result of these innovative approaches, the possibilities for early detection and prevention of faults are significantly increased. This is important for ensuring the smooth operation of power systems and …

Quantitative Assessment And Characterization Of Tool Wear Phenomena In Advanced Manufacturing Processes, Oybek Valijonovich Tuyboyov

Technical science and innovation

This paper explores the quantitative assessment and characterization of tool wear phenomena in advanced manufacturing processes, employing a multifaceted approach encompassing traditional measurements, image processing, machine learning, and predictive modeling. The study emphasizes the intricate dynamics of tool wear and its direct impact on cutting tool performance, addressing challenges in real-time monitoring and optimization of machining operations. Traditional methods like VBmax measurement are juxtaposed with advanced techniques such as the improved conditional generative adversarial net with a high-quality optimization algorithm (CGAN-HQOA), efficient channel attention destruction and construction learning (ECADCL), and shape descriptors based on contour, moments, orientations, and texture. Artificial …

Implementation Of A Realistic Artificial Data Generator For Crash Data Generation, Lauren Hoover, Md. Istiak Jahan, Tanmoy Bhowmik, Sudipta Dey Tirtha, Karthik C. Konduri, John Ivan, Kai Wang, Shanshan Zhao, Joshua Auld, Naveen Eluru

Civil and Environmental Engineering Faculty Publications and Presentations

In this paper, a framework is outlined to generate realistic artificial data (RAD) as a tool for comparing different models developed for safety analysis. The primary focus of transportation safety analysis is on identifying and quantifying the influence of factors contributing to traffic crash occurrence and its consequences. The current framework of comparing model structures using only observed data has limitations. With observed data, it is not possible to know how well the models mimic the true relationship between the dependent and independent variables. Further, real datasets do not allow researchers to evaluate the model performance for different levels of …

Implementing A Solar Photovoltaic Station In Watering Systems Utilizing Complex Software, Akbarxon Sarvar O'G'Li Uroqov, Faxriddin Jaylovovich Nosirov, G'Olibjon Pardayevich Arzikulov, Zarina Amriddin Qizi Sayfutdinova

Technical science and innovation

This article explores the benefits of transitioning from traditional agricultural irrigation systems to more cost-effective alternatives powered by renewable energy sources. By integrating solar photovoltaic technology into irrigation processes, significant reductions in resource wastage, estimated at 45-50%, are achievable through the implementation of drip irrigation techniques. This results in enhanced agricultural productivity. Moreover, the utilization of solar panels in green zones mitigates surface temperature increases, contributing to a 2-5% boost in electricity production. Currently, irrigation facilities primarily rely on the main energy grid. However, transitioning to renewable energy sources decreases reliance on non-renewable fuels, reduces greenhouse gas emissions, and fosters …

Theory Of Development And Improvement Of The Mathematical Model Of The Methodology Of Public Control In The Management Of Occupational Safety And Industrial Risks, Aliakbar Khamidullaevich Rasulev, Sunnatilla Suleymanovich Suleymanov, Nodira Bakhadirzhanovna Gaibnazarova

Technical science and innovation

The article develops and analyzes a mathematical model based on a logical flowchart of the methodology of public control in the management of occupational safety and industrial risks and probability theory, according to the model, the results of compliance with the requirements of social cooperation on occupational safety lead to a sharp increase in the probability of reliability, management efficiency becomes higher. Analysis of the mathematical model of the developed logical flowchart based on probability theory has shown that when the parties cooperate to monitor the results of compliance with labor protection requirements, they lead to a sharp increase in …

Research Of The Influence Of Dust On Photovoltaic Modules, Anvarjon Mirolimov, Xalmurat Iliev

Technical science and innovation

The influence of dust concentrations on the current-voltage characteristics (voltampere characteristics) of photovoltaic modules (PVM) based on crystalline silicon in laboratory conditions. It was investigated how an uncleaned panel affects the output power. The tests were carried out in the city of Tashkent on the territory of the “National Research Institute of Renewable Energy Sources”. The objects were located co-plurally as specified in GOST R 60904-1 Photoelectric devices. Part 1. Measurement of current-voltage characteristics. Measurements of a cleaned photovoltaic module with a maximum power of 330 W and not a cleaned one of 236 W were obtained. Based on the …

Assessment Of Improvement In Unpaved Roadway Performance Using 3d Geogrids Under Cyclic Loading, Munibhaskar Pagadala

Doctoral Dissertations and Master's Theses

Geogrids have been used for decades to improve the performance in both paved and unpaved road construction. This research focuses on quantifying the performance and optimizing the design of unpaved roadways using the results from an extensive cyclic triaxial testing program. Twenty-seven cyclic triaxial tests were performed, consisting of unreinforced (control) and reinforced samples using two types of 3D geogrids: Grid1 and Grid2. The samples measured 150 mm in diameter and a height of 300 mm. The tests were run under different loading sequences ranging from 41 kPa to 55 psi (6 psi to 8 psi of confining stress and …

Selective Oxidation Of Iron In Chalcopyrite For Enhanced Copper Recovery, Khojiakbar Shuxrat O'G'Li Sultonov, Shokhrukh Toshpulatovich Khojiev, Gulnoza Berdiyor Qizi Beknazarova, Malika Sayfullayevna Saidova

Technical science and innovation

This study explores the thermodynamic feasibility of selectively oxidizing iron contained in chalcopyrite mineral while preventing the oxidation of copper sulphide, with the ultimate goal of enhancing the copper concentration in the sulphide concentrate. A redox reaction in the solid phases between chalcopyrite and copper (I) oxide was constructed and subjected to thermodynamic analysis. The research identifies a crucial temperature range of 498-598 K (225-325 °C) as the most favourable for the redox reaction. The equilibrium constants at the selected optimal temperatures, 1.152 for chalcopyrite and 1.137 for copper (I) oxide, indicate that the redox reaction adheres to the expected …

Solving Water Resources Problems - Water Saving In The Republic Of Uzbekistan, Rustam Muxammatdjanovich Raximov

Technical science and innovation

In this article we will talk about the problems of water resources in the Republic of Uzbekistan. The problem of drinking water supply, solutions to provide drinking water to the population of Uzbekistan. The largest consumers of fresh water in Uzbekistan are farmers. Due to outdated infrastructure, 40% of water is wasted. Rising food prices and the risk of spreading disease are the first signs of water shortages that we may experience in the coming еars. Uzbekcosmos told how to solve the problem. Water is an invaluable resource used not only in the home, but also in the production and …

Modelling Of Heat Transfer In An Air Solar Collector, Shakhnoza Abduvaxitovna Sultanova, Jasur Esirgapovich Safarov, A.A. Mambetsheripova

Technical science and innovation

This study is the prediction, depending on time and different geographical and climatic situations, of different operating parameters: solar radiation, ambient and outlet coolant temperature, heat exchange coefficients and losses. All these determine, in the absence of measurements, the efficiency of the system modelled with existing models with respect to these parameters. These models are usually compared with experimental results. Before modelling, it is necessary to investigate the different heat transfer and exchange regimes that exist between the different elements of this system in order to eventually have a system of equations governing this exchange. The modelling principle is to …

A Study On The Influence Of Cutting Parameters On Surface Roughness And Visualization Through Contour Plots And 3d Surface Profiles, Zayniddin Nosirovich Muxiddinov

Technical science and innovation

This research investigates the intricate relationship between cutting parameterscutting speed, feed rate, and depth of cut and surface roughness in machining processes. Surface roughness is a key determinant of machined surface quality, and optimizing cutting parameters is crucial for achieving superior finishes. Employing advanced visualization techniques, including contour plots and 3D surface profiles, the study offers a comprehensive exploration of surface topography dynamics. Statistical analyses and regression modeling enhance the quantitative understanding of how cutting parameters interact to shape surface roughness. The research affirms the significant influence of cutting speed, feed rate, and depth of cut, providing practical insights for …

Reliability Of Using Secondary And Tertiary Treated Wastewater In Concrete Mixing And Curing, Amany G. Micheal Prof., Haidy Abd El Salam

Architectural Engineering

Water scarcity is a problem that faces many regions. In a developing and arid countries, the need for fresh water is exponentially increasing. One of the most water consuming industries is the construction industry, especially in concrete manufacturing. This research is an evaluation of the Reliability of recycled wastewater to be used in concrete manufacturing. Two different wastewater treatment regimens are implemented: secondary and tertiary treated wastewater. The treated wastewater, either secondary or tertiary, replaces potable water with percentages of 25%, 50%, and 100%. The mixture of the two types of water is used in concrete mixing and curing. Control …