Civil and Environmental Engineering Commons^™

Prototype Development Of Small Scale Transportable Fuel Production System For Agricultural Byproducts, Jurarat Nisamaneenate

Chulalongkorn University Theses and Dissertations (Chula ETD)

The objective is to study the potential of peanut shell waste and cassava rhizome conversion using a modular fixed bed gasifier coupled with thermal integration unit. The thermal integration unit improved gasification reaction in which lower tar content and high gas production efficiency can be achieved. The air flow rate had integrated effects on product yield and composition; higher air flow rate resulted in higher gas yield with less tar and char. The result from peanut shell gasification indicated the optimal conditions without catalyst addition at air flow rate of 3.06 m3/hr where carbon and hydrogen conversions were 87.10% and …

Extreme Weather Disaster Resilient Port And Waterway Infrastructure For Sustainable Global Supply Chain, Quang Van Nguyen

Electronic Theses and Dissertations

Global supply chain is largely dependent on seaports and marine terminals. Ports serve international cargo traffic for imports and exports. About 90% of the world’s goods are transported by sea and over 70% as containerized cargo ships. Coastal hurricanes/cyclones and rainfall flood disasters cause major disruptions for sea shipping traffic, disruptions of port infrastructure, and adverse impacts on coastal communities each year. Additionally, these weather related disasters threaten millions of people, damage infrastructure, and cost billions of dollars in global supply chain disruptions. Sustainable global supply chains, port infrastructure, and coastal community impact by these extreme weather disasters are the …

Coupling Infrastructure Resilience And Flood Risk Assessment For A Coastal Urban Watershed, Justin Joyce

Electronic Theses and Dissertations

This thesis sheds light on coupling potential flood risk and drainage infrastructure resilience of low-lying areas of a coastal urban watershed to flood hazards and subsequent multi-scale impacts of those hazards via detailed modeling frameworks. Physically based models along with statistical models are employed to highlight the complexity for characterizing flood risk while evaluating such risk under various levels of adaptive capacity from traditional flood management techniques to low impact development (LID), as a first step to conduct resilience assessment. Findings indicate that the coupling flood risk and infrastructure resilience is achievable by the careful formulation of flood risk associated …

Water–Soil–Vegetation Dynamic Interactions In Changing Climate, Xixi Wang, Xuefeng Chu, Tingxi Liu, Xiangju Cheng, Rich Whittecar

Civil & Environmental Engineering Faculty Publications

Previous studies of land degradation, topsoil erosion, and hydrologic alteration typically focus on these subjects individually, missing important interrelationships among these important aspects of the Earth's system. However, an understanding of water–soil–vegetation dynamic interactions is needed to develop practical and effective solutions to sustain the globe's eco-environment and grassland agriculture, which depends on grasses, legumes, and other fodder or soil-building crops. This special issue is intended to be a platform for a discussion of the relevant scientific findings based on experimental and/or modeling studies. Its 12 peer-reviewed articles present data, novel analysis/modeling approaches, and convincing results of water–soil–vegetation interactions under …

Prestressed Concrete Inverted Tee Beams With Cfrp For Building Structures, Herish A. Hussein, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

Presented herein is the outcome of a study of prestressed concrete inverted tee beams with carbon fiber reinforced polymer (CFRP) sheets for possible use in building structures. To determine an effective approach for the use of CFRP, nine different retrofitting schemes are investigated for a prestressed beam under quasi-static distributed load to increase flexural strength. The theoretical analysis is based on coupling moment-curvature relations with a central finitedifference formulation. Three different thicknesses of CFRP sheets are studied in both tension and compression and effective retrofitting schemes are identified.

Numerical Modeling Of The Interactions Between Nonlinear Waves And Arbitrarily Flexible Vegetation, Navid Tahvildari

Civil & Environmental Engineering Faculty Publications

Coastal wetlands are among the natural features with the capability to dissipate wave energy and reduce storm damage. Inadequate representation of wave and vegetation characteristics in numerical models may reduce their capability in predicting wave processes over wetlands. Previous numerical wave models have typically applied simplifications on vegetation behavior. For instance, vegetation stems were usually assumed to be rigid or semi-flexible and thus extreme stem deflections could not be captured. In this study, a time-domain nonlinear numerical model based on extended Boussinesq formulation is developed and coupled with a numerical model for vegetation blade dynamics that allows for arbitrary flexibility. …

Effects Of Sea Level Rise On Hydrology: Case Study In A Typical Mid-Atlantic Coastal Watershed, Xixi Wang, Rui Li, Homa Jalaeian Taghadomi, Shohreh Pedram, Xiao Zhao

Civil & Environmental Engineering Faculty Publications

Sea level rise (SLR) can negatively affect the hydrology of coastal watersheds. However, the relevant information is incomplete and insufficient in existing literature. The objective of this study is to present a modeling approach to predict long-term effects of SLR on changes of flood peak, flood stage, and groundwater table with an assumption that the historical climate would reoccur in the future. The study was conducted for a typical coastal watershed in southeast USA. The results indicate that sea level had been rising at a rate of 4.21 mm yr⁻¹ from 1948 to 1982 but at a faster rate …

Evaluation Of Mechanical Parameters Of Contaminated Road Base And Railway Ballast, Prajwol Tamrakar

Open Access Theses & Dissertations

This Dissertation comprises two topics in the area of transportation geotechnics that focus on the evaluation of stiffness parameters of contaminated road base and railway ballast. The abstracts of these two studies are provided in the following two paragraphs.

The performance of a flexible pavement depends on the mechanical characteristics of its unbound granular base layer. The mechanical characteristics such as stiffness and deformation resistance depend on many factors such as the material gradation, fines content, moisture content, physical properties of coarse aggregate and more. The base materials are often contaminated by the excessive fines that is caused by improper …

Asset Management Support Tools To Assist Agencies In The Development Of Guardrail Preservation Programs, Sandra N. Gutierrez

Open Access Theses & Dissertations

The purpose of this Thesis is to develop a Guardrail Asset Management Framework and a Condition-Based Model to assist agencies in the development of guardrail preservation programs. Both of the guardrail asset management tools can be incorporated into an existing asset management program to assist agencies in utilizing guardrail inventory to forecast key asset management parameters such as the guardrail condition, funds necessary for maintenance and repair, backlogged funding, guardrail system value, and the guardrail sustainability ratio. Each of these parameters is described and determined for a case study involving six scenarios modeling funding and maintenance constraints that can arise …

Integrating Manufacturing Geometric Imperfections In The Inelastic Behavior Modeling Of Joints Used In Three-Dimensional Structures, Alfonso Andres Garcia

Open Access Theses & Dissertations

Three-dimensional structures follow design practices on the common assumption that joints are either rigid, or pinned. However, the non-linear behavior of engagement of the joints is required to be incorporated into the analysis. This research is intended to incorporate manufacturing geometric imperfections into the mechanical analysis of reticulated space structures jointing systems. Imperfect jointing systems deviate from the as-designed models in such a way that the location of the connecting surfaces does not follow the designed interaction path between the component elements. However, current structural analysis methodologies do not consider manufacturing geometric imperfections and often fail to consider the stresses …

Cost-Effective Recovery Of Concentrated Cooling Tower Blowdown Using The Cerro Process, Lindsey Nicole Larson

Open Access Theses & Dissertations

The Concentrate Enhanced Recovery Reverse Osmosis (CERRO) process is a seawater-RO unit that can cost-effectively achieve extremely high recoveries from water high in silica, carbonate and sulfate concentrations. This relatively new technology takes advantage of the induction time of potential foulants to recover more water than what is normally achievable with a conventional desalination system. The scope of the project was to evaluate the efficiency of the CERRO process as a pilot study using cooling tower blowdown which varied in water quality parameters daily. It was found that the CERRO pilot could successfully achieve 85% recovery, and the main limitation …

Quantification Of The Impact Of Asphalt Pavement Conditions On Gas Emissions, Oscar Daniel Gonzalez Calvo

Open Access Theses & Dissertations

This research develops a methodology to quantify the impact of asphalt pavement conditions on vehicular gas emissions based on statistical analysis to correlate the relationship between asphalt pavement roughness and gas emissions. ANOVA (Analysis of Variance) hypoThesis tests were used to compare the factors affecting the results. The roughness was measured with the International Roughness Index (IRI) using a profilometer provided by TxDOT and the gas emissions were measured with a Portable Emission Measurement System (PEMS).

This research also presents the savings obtained in gas emissions using different maintenance and rehabilitation strategies established by TxDOT (Preventive Maintenance, Light Rehabilitation, Medium …

The Former Asarco Demolition Fallout, A Post Study On Lead Soil Concentrations And Environmental Agents Of Redistribution In El Paso, Texas, Stephanie A. Robinson

Open Access Theses & Dissertations

The former El Paso ASARCO Smelting and Refining Co. operated between 1877 and 1999, the pyrometallurgic activity was estimated to have discharged excess of a 1,000 tons of lead (Pb) into the atmosphere from 1969-71. It was estimated 96 tons of (Pb) were emitted on an annual basis from the standing ore and fluid beds. The Environmental Protection Agency (EPA) determined that lead (Pb) is the heavy metal of the highest concentration within the vicinity of the smelter. After the smelter production ceased, flash flooding common to the southwest, such as the 2006 historic flood, increased transportation of superficial contaminants …

Uav-Based Bridge Inspection And Computational Simulations, Luis Duque

Electronic Theses and Dissertations

The use of Unmanned Aerial Vehicles (UAV), commonly known as drones, has significantly increased in the field of civil engineering due to the poor condition of the United States’ infrastructure. The American Society of Civil Engineers (ASCE) recently reported that more than 9.1% of the United States’ bridges were structurally deficient and required attention and maintenance to ensure appropriate structural performance. Meanwhile, current practices are expensive and unsafe for bridge inspectors, requiring innovative and safer methods for the study of bridges. The goal of this paper was to identify better techniques to not only inspect, quantify, and determine the effect …

Rubber Additives To Concrete Specimens, Kendall J. Sweitzer, Mary Mccannon

Williams Honors College, Honors Research Projects

Rubber, as an additive to concrete, would hypothetically cause a concrete specimen to take on some mechanical characteristics of the rubber to a certain degree. In particular, the concrete’s durability should increase when exposed to fluctuating temperature conditions due to the rubber additive. This experiment sets out to test crumb rubber as a concrete additive, cured under various atmospheric conditions. The effects shall be measured via a simple concrete compression test.

Unfortunately, several errors took place during experimental process that led to inconclusive results. However, it can be reasonably considered from testing Matrix One that the addition of crumb rubber …

Compressive Strength Relative To Sustainable Materials In Concrete, Brad Harvey

Williams Honors College, Honors Research Projects

The objective of this study is to determine how integrating abundant waste materials into concrete affects its compressive strength. This research will be used to benefit the construction industry by replacing a portion of a conventional concrete mix (cement, stone, sand, and water) with more sustainable materials. In order to create a more sustainable concrete mixture, the following mix design and methodology was followed.

The initial step was to create an updatable MS Excel spreadsheet to aid in the mix development (the spreadsheet is shown in Appendix A). These sheets allowed for easy transitions from one mix to another by …

Chemical Modification Of Crumb Rubber To Increase Its Bonding With Concrete, Mary T. Mccannon, Kendall J. Sweitzer

Williams Honors College, Honors Research Projects

The hydrophilicity of crumb rubber was increased with wet chemical modification and added to concrete to increase its adhesion with concrete, consequently the compressive strength relative to that of concrete with untreated rubber. Other modification methods were tested on crumb rubber and rubber sheets to yield an increase in hydrophilicity. Certain tests were less reliable for powder testing or tedious and time consuming and concrete materials and rubber may not be homogeneous.

For wet chemical modification, several approaches were attempted. First, crumb rubber was soaked in 5% sodium hydroxide, 5% potassium permanganate and saturated sodium bisulfite, tested for hydrophilicity using …

Engineering Professors’ Perspectives On Gender And Assessment Of Teamwork, Kacey Beddoes, Grace Panther

Department of Civil and Environmental Engineering: Faculty Publications

Teamwork is an important component of engineering education programs; however, when not facilitated well, it can be a site of gender biases. The aim of this article is to thematically explore what and how engineering professors think about gender in the assessment of teamwork. In 2014 and 2015, semi-structured interviews were conducted with 39 engineering professors in the United States. Interviews covered a wide range of topics, with one section of the interviews devoted to teamwork specifically. For this article, the parts of the interviews about assessment of teamwork are analyzed. It was found that most participants were unaware of …

Development Of A Statistically-Based Methodology For Analyzing Automatic Safety Treatments At Isolated High-Speed Signalized Intersections, Remigiusz M. Wojtal, Laurence R. Rilett

Department of Civil and Environmental Engineering: Faculty Publications

Crashes at isolated rural intersections, particularly those involving vehicles traveling perpendicularly to each other, are especially dangerous due to the high speeds involved. Consequently, transportation agencies are interested in reducing the occurrence of this crash type. Many engineering treatments exist to improve safety at isolated, high-speed, signalized intersections. Intuitively, it is critical to know which safety treatments are the most effective for a given set of selection criteria at a particular intersection. Without a well-defined decision making methodology, it is difficult to decide which safety countermeasure, or set of countermeasures, is the best option. Additionally, because of the large number …

Quantifying Effectiveness Of Streambank Stabilization Practices On Cedar River, Nebraska, Naisargi N. Dave, Aaron R. Mittelstet

Department of Civil and Environmental Engineering: Faculty Publications

Excessive sediment is a major pollutant to surface waters worldwide. In some watersheds, streambanks are a significant source of this sediment, leading to the expenditure of billions of dollars in stabilization projects. Although costly streambank stabilization projects have been implemented worldwide, long-term monitoring to quantify their success is lacking. There is a critical need to document the long-term success of streambank restoration projects. The objectives of this research were to (1) quantify streambank retreat before and after the stabilization of 18 streambanks on the Cedar River in North Central Nebraska, USA; (2) assess the impact of a large flood event; …

Removal Of Pharmaceuticals From Aqueous Solutions Using A1-Mg/Rgo Composite, Spencer Jones

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

A Proposed Method Of Correcting The Construction Entries In The 2006 Philippine Input-Output Table, Albert E. Lamberte, Krista Danielle Yu, Caesar Cororation

Angelo King Institute for Economic and Business Studies (AKI)

The construction of national input-output (IO) tables follows internationally acceptable standards such as the United Nations Systems of National Accounts (UN SNA) and European System of Accounts (ESA). These standards are used to ensure tractability and coherence between country tables. The 2006 Philippine IO table published by the Philippine Statistics Authority (PSA) assumes that the construction sector does not provide any input to the production of output for any economic sector. With the booming infrastructure development in the Philippines, this assumption that intermediate demand for construction output has a value of zero is unreasonable. This study proposes a corrective approach …

Projecting Regional Climate And Cropland Changes Using A Linked Biogeophysical-Socioeconomic Modeling Framework: 1 Model Description And An Equilibrium Application Over West Africa, Guiling Wang, Kazi Farzan Ahmed, Liangzhi You, Miao Yu, Jeremy S. Pal, Zhenming Ji

Civil and Environmental Engineering Faculty Works

Agricultural land use alters regional climate through modifying the surface mass, energy, and momentum fluxes; climate influences agricultural land use through their impact on crop yields. These interactions are not well understood and have not been adequately considered in climate projections. This study tackles the critical linkages within the coupled natural-human system of West Africa in a changing climate based on an equilibrium application of a modeling framework that asynchronously couples models of regional climate, crop yield, multimarket agricultural economics, and cropland expansion. Using this regional modeling framework driven with two global climate models, we assess the contributions of land …

The Experimental Determination Of The Moment Of Inertia Of A Model Airplane, Michael Koken

Williams Honors College, Honors Research Projects

The objective of this project is to suggest that the moment of inertia for irregular shaped objects can easily be determined experimentally. The objects considered in this experiment were a solid wooden block and a model airplane. To ensure that the method and configuration is sufficient a wooden block with known moments of inertia was first tested, and the results from the experiment were compared to the known and accepted values. For this particular experiment, the periods were determined by timing how long 10 oscillations lasted for 10 different trials, and then taking the average of those 10 trials to …

An In-Depth Evaluation Of Shear Box Compactor For Hot Mix Asphalt, Isaac Jaime Aguilar

Open Access Theses & Dissertations

Asphalt pavement is present in each roadway in every town or city today and it is paramount to properly design pavement to efficiently reduce its deterioration. To determine how pavement fails, pavement specimens prepared in the laboratory undergo performance tests which demonstrate the pavements strength and durability. Performance tests require little variability from compacted specimens, and it is critical to have a compaction method which is similar to field compaction and produces homogenous specimens. Currently, laboratory performance test specimens are obtained with the Superpave Gyratory Compactor (SGC). That device has few similarities to the rolling compactor, which performs the actual …

Studies Of Air Pollutants And Their Impact On Respiratory And Cardiovascular Diseases In The El Paso Del Norte Region With Emphasis On Mobile Emissions, Juan Gustavo Arias Ugarte

Open Access Theses & Dissertations

Air pollution may cause different diseases, such as cardiovascular and lung diseases. Traffic is a major source of mobile emissions causing air pollution. Exhaust emissions from mobile sources (Emissions of Carbon Monoxide, Nitrogen Oxides and Hydrocarbons) and Non-exhaust (Brake and Tire) are complex mixtures of gases and dust, including a large number of ultrafine particles, especially in areas with high traffic density. Recent studies have shown high rates of morbidity and mortality in people exposed to these types of emissions because the fine and ultrafine particles can be transported from the respiratory airways to the organs, thus contributing to increase …

Experiences Of Public Agency Managers When Making Outsourcing Decisions, Shakeel Baig

Walden Dissertations and Doctoral Studies

Managers in state transportation agencies in the United States must frequently choose between using the talents and abilities of in-house staff or outsourcing for road and bridge design projects. Budgetary crises have strongly affected funding for transportation infrastructure. Facing budgetary pressures to suppress costs, managers must frequently make the choice of outsourcing a project or performing it in-house. Yet, decision-making models for these decisions are inadequate. The purpose of this phenomenological study was to explore and describe the lived experiences of public agency managers when making decisions to outsource the core government functions such as road and bridge design projects. …

Bs News January/February

Building Services Engineering

No abstract provided.

Simulation As Supplementary Tool In Construction Management Education, Saeed Rokooei, James D. Goedert, Asregedew Woldesenbet

Department of Construction Engineering and Management: Faculty Publications

Many academic programs utilize simulation applications to supplement higher education, but there are only a few applications responding to the need in construction curricula, particularly with a focus on project management. Project management is an interdisciplinary area of study, crosscutting multiple fields including the construction, information technology, and business sectors. This paper presents the design, development, and test of a research project entitled Project-oriented Educational Research Fostering Excellence in Cyber-infrastructure Teaching (PERFECT). It investigates the effect of a construction project management simulation on construction management students’ engagement and perceptions at the University of Nebraska- Lincoln.

The goal of PERFECT was …

Moving Integrated Weed Management From Low Level To A Truly Integrated And Highly Specific Weed Management System Using Advanced Technologies, S. L. Young, S. K. Pitla, F. K. Van Evert, J. K. Schueller, F. J. Pierce

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Integrated weed management (IWM) is one of the most commonly referred to approaches for sustainable and effective weed control in agriculture, yet it is not widely practiced, likely because current IWM systems fail to meet performance expectations of growers. The effectiveness and value of IWM systems should increase with increasing application specificity and true integration made possible with contemporary advances in technology, information systems and decision support. IWM systems can be classified based on their degree of application specificity and level of integration of tactics. In the application specificity pathway, a tactic is applied at a range of scales, from …