Civil and Environmental Engineering Commons^™

Experimental Investigation Of The Behavior Of The Steel Reinforced High Density Polyethylene And Corrugated Metal Pipe, Safa Sadat Masajedian

Civil Engineering Theses - Archive

Steel reinforced high density polyethylene pipes are gaining popularity these days because of their good performance and advantages of them in comparison to the other pipe materials. By inverting the steel ribs vertically in to the HDPE materials, strength of steel and flexibility and light weight of HDPE materials have been combined. However due the limited study in this area, the failure modes and design parameters are not classified.This study investigates the behavior and failure modes of SR-HDPE pipes under the simulated soil load and compares the results with the data obtained from the test on corrugated metal pipe under …

Evaluation Of Building Information Modeling Applications For Small Construction Companies, Agustin Villafana

Civil Engineering Theses - Archive

This thesis concerns developing recommendations to help small construction company's transition from traditional two dimensional plans to a Building Information Modeling (BIM) management process. Due to the cost of implementing BIM, the primary focus of the thesis is onthe transitioning state of these two management areas in an effort to facilitate full integration of smaller contractors into BIM technologies at a future time.Three case studies are used to assess and evaluate the effects of building information modeling on the schedule, material procurement, and information modeling aspects of a project. The intent of the case studies is to demonstrate a net …

An Overview Of Mitigation Strategies For Settlements Under Bridge Approach Slabs, Raja Veerendra Yenigalla

Civil Engineering Theses - Archive

Settlement and heave related movements of bridge approach slabs relative to bridge decks create a bump in the roadway causing inconvenience to the travelling public and at times so large as to make travelling unsafe. Hence, it is important to adopt suitable remedial methods to mitigate the approach settlements so as to ensure safe traveling conditions and also to decrease the repair/maintenance costs. This thesis presents an overview of a few case studies on different mitigation techniques applied on bridge approach settlement problems at various locations in the state of Texas. The methods employed to mitigate the settlement including Polyurethane …

Use Of Steel Fiber Reinforced Concrete In Structural Members With Highly Complex Stress Fields, Tarun Pareek

Civil Engineering Theses - Archive

Reinforced concrete (RC) members with significant geometric discontinuities and complex stress distributions under loading require considerable analyses and usually complicated reinforcement detailing. RC members with large openings are one of the examples. These large openings may interrupt the load transfer by direct concrete struts and cause substantial decrease in strength and unpredictable failure modes. The reinforcement detailing of these concrete members based on strut-and-tie models (STMs) is generally complicated and very often, these models cannot predict the failure mechanism due to localized damages. The actual stress fields in such members are typically very different from that predicated by STMs, as …

The Effects Of A Variable Modulus Of Elasticity On Prestress Losses In Bridge Girders, Brahama Prakashni Singh

Civil Engineering Theses - Archive

The purpose of this research is to evaluate a method proposed by Franz Dischinger (Dischinger, 1939) to consider the effects of a variable modulus of elasticity (MOE) of concrete over a period of time. Current guidelines suggested by the American Association of State Highways and Transportation Officials (AASHTO) assume a constant value for the MOE and base its calculation on the unit weight of concrete and the twenty eight day compressive strength of concrete. A few methods such as the ACI 209 Model Code (ACI 209, 1982) and CEB-FIP 1990 (CEB-FIP 1990, 1990) provide guidelines for the calculation of a …

Infrared-Based Measurements Of Velocity, Turbulent Kinetic Energy, And Dissipation At The Water Surface In A Tidal River, C. Chris Chickadel, Stefan A. Talke, Alexander R. Horner-Devine, Andrew T. Jessup

Civil and Environmental Engineering Faculty Publications and Presentations

Thermal infrared (IR) based particle image velocimetry (PIV) is used to measure the evolution of velocity, turbulent kinetic energy (TKE), and the TKE dissipation rate at the water surface in the tidally influenced Snohomish River. Patterns of temperature variability in the IR imagery arise from disruption of the cool skin layer and are used to estimate the 2D velocity field. Comparisons of IR based PIV mean velocity made against a collocated acoustic velocimeter demonstrate high correlation (r2 > 0.9). Over a tidal period, surface TKE computed from the IR velocity varies from 10-4 J·kg-1 to 3x10-3 J·kg-1, with an average difference …

Key Factors Affecting The Accuracy Of Reidentification Of Trucks Over Long Distances Based On Axle Measurement Data, Mecit Cetin, Christopher Monsere, Andrew Nichols, Ilyas Ustun

Civil and Environmental Engineering Faculty Publications and Presentations

Vehicle reidentification methods can be used to anonymously match vehicles crossing two locations based on vehicle attribute data. This paper investigates key factors that affect the accuracy of vehicle reidentification algorithms. The analyses are performed with reidentification algorithms to match commercial vehicles that cross upstream and down-stream pairs of weigh-in-motion (WIM) sites that are separated by long distances, ranging from 70 to 214 mi. The data to support this research come from 17 fixed WIM sites in Oregon. Data from 14 pairs of WIM sites are used to evaluate how various factors affect matching accuracy; factors include the distance between …

Rule-Based Decision Support System For Sensor Deployment In Drinking Water Networks, Natthaphon Prapinpongsanone

Electronic Theses and Dissertations

Drinking water distribution systems are inherently vulnerable to malicious contaminant events with environmental health concerns such as total trihalomethanes (TTHMs), lead, and chlorine residual. In response to the needs for long-term monitoring, one of the most significant challenges currently facing the water industry is to investigate the sensor placement strategies with modern concepts of and approaches to risk management. This study develops a Rule-based Decision Support System (RBDSS) to generate sensor deployment strategies with no computational burden as we oftentimes encountered via large-scale optimization analyses. Three rules were derived to address the efficacy and efficiency characteristics and they include: 1) …

Solution Phase And Membrane Immobilized Iron-Based Free Radical Reactions: Fundamentals And Applications For Water Treatment, Scott Romak Lewis

University of Kentucky Doctoral Dissertations

Membrane-based separation processes have been used extensively for drinking water purification, wastewater treatment, and numerous other applications. Reactive membranes synthesized through functionalization of the membrane pores offer enhanced reactivity due to increased surface area at the polymer-solution interface and low diffusion limitations. Oxidative techniques utilizing free radicals have proven effective for both the destruction of toxic organics and non-environmental applications. Most previous work focuses on reactions in the homogeneous phase; however, the immobilization of reactants in membrane pores offers several advantages. The use of polyanions immobilized in a membrane or chelates in solution prevents ferric hydroxide precipitation at near-neutral pH, …

Use Of Vegetative Mulch As Daily And Intermediate Landfill Cover, Assal Edwar Haddad

Electronic Theses and Dissertations

Management of yard waste is a significant challenge in the US, where in 2008 13.2% of the 250 million tons of municipal solid waste (MSW) was reported to be yard waste. This study describes research conducted in the laboratory and field to examine the application of vegetative mulch as daily and intermediate landfill cover. Mulch was found to exhibit stronger physical properties than soil, leading to a more stable landfill slope. Compaction of mulch was found to be significantly greater than soil, potentially resulting in airspace recovery. Degradation of mulch produced a soil-like material; degradation resulted in lower physical strength …

Steel Beams Strengthened With Ultra High Modulus Cfrp Laminates, Nisal Abheetha Peiris

University of Kentucky Doctoral Dissertations

Advanced composites have become one of the most popular methods of repairing and/or strengthening civil infrastructure in the past couple of decades. While the use of Fiber Reinforced Polymer laminates and sheets for the repair and strengthening of reinforced concrete structures is well established, research on the application of FRP composites to steel structures has been limited. The use of FRP material for the repair and rehabilitation of steel members has numerous benefits over the traditional methods of bolting or welding of steel plates. Carbon FRPs (CFRPs) have been preferred over other FRP material for strengthening of steel structures since …

The Sensitivity Of Land Emissivity Estimates From Amsr-E As C And X Bands To Surface Properties, Hamid Norouzi, Marouane Temimi, William B. Rossow, Cindy Pearl, M. Azarderakhsh, Reza Khanbilvardi

Publications and Research

Microwave observations at low frequencies exhibit more sensitivity to surface and subsurface properties with little interference from the atmosphere. The objective of this study is to develop a global land emissivity product using passive microwave observations from the Advanced Microwave Scanning Radiometer – Earth Observing System (AMSR-E) and to investigate its sensitivity to land surface properties. The developed product complements existing land emissivity products from SSM/I and AMSU by adding land emissivity estimates at two lower frequencies, 6.9 and 10.65 GHz (C- and X-band, respectively). Observations at these low frequencies penetrate deeper into the soil layer. Ancillary data used in …

Environmental Study Of Solid Waste Collection, Mousa Awad Maimoun

Electronic Theses and Dissertations

The growing municipal solid waste generation rates have necessitated more efficient, optimized waste collection facilities. The majority of the US collection fleet is composed of diesel-fueled vehicles which contribute significant atmospheric emissions including greenhouse gases. In order to reduce emissions to the atmosphere, more collection agencies are investigating alternative fuel technologies such as natural gas, biofuels (bio-gas and bio-diesel), and hybrid electric technology. This research is an in-depth environmental analysis of potential alternative fuel technologies for waste collection vehicles. This study will evaluate the use of alternative fuels by waste collection vehicles. Lifecycle emissions, cost, fuel and energy consumption were …

Mass Conservation Analysis For The Lower St. Johns River Using Continuous And Discontinuous Galerkin Finite Element Methods, Lillie E. Thomas

Electronic Theses and Dissertations

This thesis provides a mass conservation analysis of the Lower St. Johns River for the purpose of providing basis for future salinity transport modeling. The analysis provides an assessment of the continuous (CG) and discontinuous (DG) Galerkin finite element methods with respect to their mass conservation properties. The following thesis also presents a rigorous literature review pertaining to salinity transport in the Lower St. Johns River, from which this effort generates the data used to initialize and validate numerical simulations. Two research questions are posed and studied in this thesis: can a DG-based modeling approach produce mass conservative numerical solutions; …

Advancing The Use Of Bim Through A Government Funded Construction Industry Competency Centre In Ireland, Alan V. Hore, Ken Thomas

Conference papers

The main aim of this paper is to develop the early case for a new Competence Centre dedicated to industry led research in the Irish construction industry. It incorporates the results of a survey carried out by the Construction IT Aliance (CITA) and also identifies similiar centres carrying out industry led research around the world. Results from the survey show a clear support for the establishment of such a centre in Ireland and, in particular, a strong interest in Building Information Modelling (BIM) as a immediate priority research area. BIM is having a profound effect worldwide on the construction industry. …

Limited Scope Permitting For Time-Sensitive Project Delivery Systems, Wayne Jensen, Bruce Fischer, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Delivery of construction projects in the United States has traditionally been based upon the design-bid-build system. TIlis system has been used to create numerous impressive structures, but it often proves expensive and usually requires considerable time, because design, permitting and construction are accomplished in sequential order and do not overlap. Several alternatives to the traditional system have been developed, many of which fall under the classification of time-sensitive project delivery systems. The most commonly used time-sensitive project delivery systems are phased and fast-track construction (FaZio, Moselhi, Theberge & Revay 1988a). Figure 1 illustrates some of the major differences between traditional …

Durability Performance Of Frp Strenghtened Concrete Beams And Columns Exposed To Hygrothermal Environment, Abulgasem Mohamed Elarbi

Wayne State University Dissertations

ABSTRACT

DURABILITY PERFORMANCE OF FRP STRENGHTENED CONCRETE BEAMS AND COLUMNS EXPOSED TO HYGROTHERMAL ENVIRONMENT

by

ABULGASEM M. ELARBI

August 2011

Advisor: Dr. Hwai-Chaung Wu

Major: Civil and Environmental Engineering (Structural Engineering)

Degree: Doctor of Philosophy

Concrete structures deteriorate over time due to exposure to various environments, including hot and humid weather. High temperature, wind, and air humidity in many hot climates can all have a negative impact on the performance of concrete structures. The most important factors are temperature and humidity - often times these effects are not immediately evident and develop years later - making determination of responsibility difficult …

Characteristic Vertical Response Of A Footbridge Due To Crowd Loading, Colin C, Caprani, Joe Keogh, Paul Archbold, Paul Fanning

Conference papers

The characteristic vertical vibration of a flexible footbridge subject to crowd loading is examined in this paper. Typically, bridge vibrations produced from a crowd of pedestrians are estimated by using an enhancement factor applied to the effect caused by a single pedestrian. In this paper, a single pedestrian model, represented by a spring mass damper, which incorporates variables such as pedestrian mass and body stiffness, is used to calibrate a computationally efficient moving force model. This calibrated moving force model is further used in Monte Carlo simulations of non-homogenous crowds to estimate characteristic vertical vibration levels. Enhancement factors, which could …

Zinc Speciation In Power Plant Burning Mixtures Of Coal And Tires, Luis F.O. Silva, Marcos L.S. Oliveira, Carmen Serra, James C. Hower

Coal Combustion and Gasification Products Journal Archive

Fly ash from the cyclone-boiler co-combustion of high-S, high volatile bituminous coal and tire-derived fuel (tdf) was studied using a variety of chemical, optical, and microbeam techniques. Fly ash, dominated by Al-Si glass with lesser amounts of coalderived carbons, Fe-spinels, and tire-derived carbons, has Zn concentrations ranging from 2200 ppm (1st ESP row) to 6900 ppm Zn (3rd ESP row). Zinc occurs in Zn-rich nanoparticles in the Al-Si glass phases and as ZnO in amorphous and crystalline nanominerals, Fe- and Zn-sulfides, Pb-Al-Fe sulfates, and Zn sulfates. Iron-rich, Al- and Ti-bearing spinels contain accessory Zn2+,Cr3+,Mn2+, and Pb2+. Fe-sulfates and phosphates nanoparticles …

Co-Disposal Of Dry Fgd By-Product With Coal Gasification Ash And Inorganic Brines, Jabulani S. Mahlaba, P.C. Pretorius, Subal Maharajh, M.P. Augustyn

Coal Combustion and Gasification Products Journal Archive

There is a growing pressure from the environmental authorities and public bodies to reduce anthropogenic pollution. Stringent environmental legislation is being implemented for industries around the world, even more so for coal consuming industries. Control of gaseous emissions is one of the areas that are receiving considerable attention towards sustainable development. Coal combustion in coal-fired power utilities emits SO~x~ to the atmosphere. Dry flue gas desulphurisation (FGD) is a well known technology often used to mitigate sulphur emissions in coal-fired power utilities. It traditionally uses lime to neutralise SO~x~, and forms a mixture of anhydrite (CaSO~4~), and calcium sulphite (CaSO~3~). …

Localization Of Free-Spanning Damage Using Mode Shape Curvature, Guirong Yan, Xuelin Peng, Hong Hao

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This Study Proposes a Damage Indicator based on Mode Shape Curvature to Localize Free-Spanning Damage of Submarine Pipeline Systems. the Feasibility of Curvatures of Low-Frequency Mode Shapes for Localizing Free-Spanning Damage of Pipeline Systems is Discussed, and Damage Indicators based on Mode Shape Curvatures Are Proposed. the Efficacy of the Proposed Damage Indicators is Demonstrated by Numerical Simulations of Dynamic Responses of a Submarine Pipeline under Ambient Conditions with Considering the Real Subsea Environment. the Proposed Approach is Simple, Which Does Not Require Baseline Data, and Thus is Promising in Practical Applications. © 2011 Published under Licence by IOP Publishing …

Modeling Same-Direction Two-Lane Traffic For Bridge Loading, Eugene J. Obrien, Bernard Enright

Articles

Many highway bridges carry traffic in two same-direction lanes, and modeling the traffic loading on such bridges has been the subject of numerous studies. Different assumptions have been used to model multiple-presence loading events, particularly those featuring one truck in each lane. Using a database of weigh-in-motion measurements collected at two European sites for over 1 million trucks, this paper examines the relationships between adjacent vehicles in both lanes in terms of vehicle weights, speeds and inter-vehicle gaps. It is shown that there are various patterns of correlation, some of which are significant for bridge loading. A novel approach to …

Magnetite Nanoparticles For Medical Mr Imaging, Zachary R. Stephen, Forrest M. Kievit, Miqin Zhang

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Magnetic resonance imaging (MRI) has become one of the most widely used and powerful tools for non-invasive clinical diagnosis due to its high soft tissue contrast, spatial resolution, and penetration depth1. In addition, images are acquired without the use of ionizing radiation or radiotracers that would cause unwanted harmful side-effects. A considerable amount of research in medical MR imaging is focused on the development of contrast agents that can provide better delineation between healthy and diseased tissue. Magnetic nanoparticles (MNPs) are a major class of nanoscale material currently under extensive development for improved diagnosis of a wide range of diseases, …

Chemicals And Allied Products Waste Treatment, Yung Tse Hung, Erick Butler, Ruth Yu-Li Yeh

Civil and Environmental Engineering Faculty Publications

© 2011 by the authors. A review of the literature published from 2008 to 2010 on topics related to chemicals and allied products is presented. The review considered several sections such as waste management, physicochemical treatment, aerobic treatment, anaerobic treatment, air emissions, soils and groundwater, and reuse.

A Multi-Analytical Approach To Understand The Chemistry Of Fe-Minerals In Feed Coals And Ashes, Marcos L.S. Oliveira, Frans Waanders, Luis F.O. Silva, Andre Jasper, Carlos H. Sampaio, Dursman Mchabe, Rachel S. Hatch, James C. Hower

Coal Combustion and Gasification Products Journal Archive

Seven feed coals used in the Brazilian power generation industry were obtained and subsequently analysed together with fly ash and bottom ash from a major Brazilian power plant. The samples were investigated by means of room temperature FeMo¨ssbauer analyses, X-ray diffraction, Raman spectroscopy, scanning electron microscope and petrographic analysis. In addition, nanometer-sized crystalline phases in coals and ashes were characterised using an energy-dispersive X-ray spectrometer and a high-resolution transmission electron microscope. The major identified Fe-bearing minerals in the coals were found to be actinolite, ankerite, chalcopyrite, chlorite, goethite, illite, ilmenite, magnesioferrite, natrojarosite, pyrite, pyrrhotite, and siderite; whilst in the fly …

Compositional Variations In Pilot Gasifier And Laboratory-Produced Slags And Their Impacts On Slag Viscosity And Coal Assessment, Alexander Ilyushechkin, Daniel Roberts, David Harris

Coal Combustion and Gasification Products Journal Archive

The flow behaviour of coal mineral matter at high temperatures is an important parameter for coal use in entrained-flow gasification technologies. Recently, gasification performance data was obtained from a series of pilot-scale gasification tests on a suite of well-characterised Australian black coals. Evaluation of the results of the pilot tests and the detailed laboratory investigations provided the opportunity for evaluation of the practical applicability of different laboratory and modelling techniques for coal assessment in terms of mineral matter behaviour in entrained flow gasification. A series of viscosity measurements was made over the range 1200–1600uC using slags produced in a pilot …

Compaction Of High-Ca Fly Ash-Al- And Al-Alloy-Composites: Evaluation Of Their Microstructure And Tribological Performance, Grigorios Itskos, Angeliki Moutsatsou, Pradeep K. Rohatgi, Nikolaos Koukouzas, Charalampos Vasilatos, Eleni Katsika

Coal Combustion and Gasification Products Journal Archive

In this study, highly calcareous and siliceous fly ash particles were utilized for the fabrication of Al- and Al-alloy-based MetalMatrix Composites (MMCs) by means of powder metallurgy. After compacting and sintering Al and Al/Si powders containing 10, 15, and 20wt. % ash particles, the homogenous (and with minimal amount of voids) microstructure of the produced composites was verified by means of Scanning Electron Microscopy (SEM). The composites were tested for their dry sliding wear behavior using a pin-on-disc machine against spheres of alumina. The worn surfaces of composites were then examined by using SEM and Energy Dispersive X-Ray Spectroscopy (EDS). …

Influence Of Chemical Reagents On Rheological Properties Of Fly Ash-Water Slurry At Varying Temperature Environment, H.K. Nail, M.K. Mishra, Karanam U.M. Rao

Coal Combustion and Gasification Products Journal Archive

About 70% of total electrical energy is generated from thermal power plants in India which in turn release about 160 Mt of fly ash as solid waste annually. Transportation and disposal of such a huge amount of fly ash is a major problem faced by the power plants. Presently fly ash is transported as lean slurry in pipe lines requiring about 80 to 85% of water with high energy input. A major impediment in high volume transportation of fly ash is its high specific gravity as compared to that of water. The objective of the present study was to evaluate …

Impact Of Manufactured Coal Ash Aggregates On Water Quality During Open Pit Restoration: 1. A Statistical Screening Test, Sangchul Hwang, Isomar Latorre

Coal Combustion and Gasification Products Journal Archive

Utilization of manufactured coal ash aggregates (MAs) as a subsoil substitute during restoration of an open pit was assessed in a three-factor, two-level factorial analysis. The factors of interest were the MA application rate (2:1 or 1:2 topsoil/MA volume ratio), rainfall intensity (high or low), and aggregate size (2.36–4.75 mm or 4.75–9.53 mm). Among the water quality parameters examined (pH, turbidity, heavy metal content (lead and cadmium), conductivity, and hardness), the last two parameters were significantly higher (p,0.05) in soil amended with MAs than in a control reactor using sand. A low rainfall intensity and larger aggregate size resulted in …

The Leachability Of Major Elements At Different Stages Of Weathering In Dry Disposed Coal Fly Ash, S.A. Akinyemi, A. Akinlua, W.M. Gitari, R.O. Akinyeye, L.F. Petrik

Coal Combustion and Gasification Products Journal Archive

Large quantities of solid residue are generated by coal-fired power stations in many parts of the World. The disposal and management of the unused fly ash remains a major problem to the environment. The weathered dry disposed ash cores comprise of major element constituents such as Al, Si, Ca, Mg, Fe, Mn, Na+ and K+. The mobility patterns and mineralogical associations of major elements in weathered dry disposed ash dumps aged 1-year-old, 8-year-old and 20-year-old from a coalfired power station in South Africa were investigated using a modified sequential extraction scheme. The extraction sequence was as follows: (1) water soluble, …