Civil and Environmental Engineering Commons^™

The Influence Of A Fixed Failure Plane On The Direct Shear Test, Kenneth Hodges Bell

Masters Theses

"The analysis of the direct or box shear test for determining the shear strength of a soil makes use of the assumption that the failure plane coincides with the plane of separation between the two halves of the box. Hvorsley, Roscoe, Hansen and others have theorized and experimentally shown that this is not always the case. The stress distributions on the failure plane, however it may be oriented, are not as uniform as generally assumed. This investigation was carried out to compare direct shear tests run on granular, air dry material where the failure was allowed to take place naturally …

The Measurement Of Explosively Induced Stresses In Rock-Like Materials With A Capacitive Transducer, Vincent Paul Crane

Masters Theses

"A capacitive transducer was developed for measuring the free surface motion in Hydrostone blocks loaded by an explosive plane wave generator approximately one foot from the specimen. The charge to specimen distance was adjusted to produce a single spall, the position of the fracture being noted on the recovered specimen. The longitudinal wave velocity in each specimen was determined by the ultrasonic pulse technique before each shot. From the above measurements the stress, strain and strain rate at the point of fracture were determined. An attempt was made to determine the actual fracture time with imbedded [sic] conductive graphite rods, …

Quality Of Surface And Subsurface Water In A Missouri Carbonate Karst Terrain (Dry Fork, Norman, And Benton Creek Watersheds), James Chi Huang

Masters Theses

"Little is known about the effect of carbonate karst terrain on water quality in the United States. Karst topography occurs over a large portion of Missouri and over a significant part of other midwestern states. The objectives of this study were the determination of the quality of surface and subsurface water in carbonate karst terrain and the investigation and evaluation of the effect of rainfall and runoff on water quality in the Meramec Spring area, east of Rolla, Missouri, during both the dry and wet seasons over the period of one year. Water samples were collected at a large number …

A Study Of The Compressibility Of Silty Soils., Marvin L. Byington

Masters Theses

"This study has been conducted to determine the applicability of the Terzaghi Theory of Consolidation and to determine the compressibility of silt soils with varying clay content. A pure silt was extracted from the Lebanon Silt Loam and mixed with varying amounts of the Onyx Cave Illite-Chlorite Clay. The compressibility of these mixtures was determined and an attempt made to apply the Terzaghi Theory in the analysis. It was found that the compressibility of soils high in silt content is very low. It was also found that the Terzaghi Theory may be applied to mixtures of 15 percent or more …

Effects Of Mixing Procedure Upon Uniformity Of Fibre Reinforced Concrete, Donald E. Nortrup

Masters Theses

"This thesis describes the effects of several methods of introducing wire fibres into a concrete mix upon the uniformity of wire fibre reinforced concrete. Various mechanical and manual methods of introducing the fibres were used and comparisons of the methods were based upon variability in splitting tensile strength and the quantitative distribution of the fibres as determined by visual inspection of sawed cylinders. Test results show that the tensile strength of concrete is increased appreciably by the inclusion of steel wire fibres in the mix and the uniformity of strength is similar to that of unreinforced concrete. The methods of …

Stress Analysis Of A Wall Footing Subjected To External Vertical Loads And Overturning Moments By The Finite Element Method, Adil Godiwalla

Masters Theses

"This investigation pertains to the stress analysis by the finite element method of a wall footing subjected to external vertical loads and external overturning moments. This problem has been reduced to a two-dimensional stress analysis problem by taking a unit length of the wall. A rectangular plate - element is used throughout this investigation. The development of the matrix equations is shown and the solution is performed by digital computer. Stresses in the horizontal direction show essentially linear variation which is in agreement with simple structural theory, while stresses in the vertical direction show severe perturbation near the column load. …

Gap-Graded Gravel For Asphaltic Paving Mixtures, Ernest Harrington Martin

Masters Theses

"The objective of this investigation was to determine if naturally occurring gap-graded gravel can produce asphaltic mixtures meeting minimum requirements for satisfactory pavement behavior.

Ten gap-graded mixes were blended by eliminating certain intermediate sized fractions or combination of fractions from the gradation of a control mix. The weight of the fractions eliminated was distributed to either the coarser or finer aggregate fractions.

All specimens were prepared and tested in strict accordance with procedures set forth in ASTM Designation D1559, "Resistance to Plastic Flow of Bituminous Mixtures Using Marshall Apparatus."

The physical properties compared and analyzed were (1) unit weight, (2) …

The Recovery And Characterization Of Organic Micropollutants From Missouri Subsurface Waters, John Warren Smith

Masters Theses

"The main objectives of this investigation were the recovery and partial characterization of organic micropollutants from Missouri subsurface waters and the evaluation of the number of filters in series required for effective removal of organic materials from water using the Carbon Adsorption Method.

The organics were recovered from a spring and two deep wells using three large capacity (1. 5 cu. ft.) activated carbon filters in series. Chloroform and ethanol were employed as primary elutants, but acetone and benzene were also investigated. Characterization was by organoleptic, chemical, and biological determinations, toxicity measurements, and solubility partitioning.

Organic materials were found in …

The Effect Of Epoxy Resin In Stone And Slag Concrete, James Chun-Min Chou

Masters Theses

"In concrete construction, the weight of the structure represents a large portion of the total load carried; thus, there is considerable advantage in reducing the weight of the concrete. To obtain this result, there are at least three approaches (1). The first method of producing lightweight concrete is by means of substituting a porous lightweight aggregate of low specific gravity for the ordinary aggregate. The second method relies on introducing large voids within the concrete or mortar mass; this is known as aerated, cellular or gas concrete. The third method is simply to omit the fine aggregate from the mix …

A Numerical Method For The Solution Of Cylindrical Shell Structures, Chen-Jow Hsiao

Masters Theses

"Many studies and analyses of shell structures to date have been either so complex and laborious as to preclude their application in practical design problems or so approximate, because of basic assumptions, as to limit their scope of application. Hence, a method of shell analysis which is convenient to use, reasonable in its results and general in its application is really needed. It is the purpose of this study to supply such a method of analysis.

In this investigation it is proposed to replace the shell structure which has an infinite number of degrees of indeterminancy with an analogous framework …

A Numerical Solution For Beam-Columns On Non-Linear Foundations, Wendelin H. Mueller Iii

Masters Theses

"A program for Matlock's recursive method, a numerical method which will analyze beams and columns with linearly varying spring supports, was modified to enable the solution of such members supported by non-linear springs. This modification was accomplished by an iterative technique. The final result of this paper is a computer program which can be used to solve beams or columns with non-linear spring supports, giving as output the deflection, slope, moment, shear, net load and curvature of the structure at uniformly spaced locations"--Abstract, page ii.

Checking Rigid-Framed Structures By Extended Moment-Area Equations, Lucky Li-Chi Chow

Masters Theses

"Using the known moments obtained from the moment distribution solution, the extended moment-area equations are used to check whether or not delta x, delta y, delta theta are truly zero, or are any other quantity they are supposed to be. In order to get a reasonably correct answer, a solution must meet both the elastic checks and the static checks for their equilibrium and compatibility functions. Using the extended moment-area equations, the magnitudes of the slopes and deflections at all of the joints in framed structures can be found easily"--Abstract, page ii.

Bending Of Isosceles Right Triangular Plates, Ping-Tung Huang

Masters Theses

"In this thesis the series expansion method is used to obtain the moments and deflections of an isosceles right triangular plate bent by arbitrary transverse loads. The method is based on using an antisymmetric load on a square plate. Two boundary conditions are solved and the numerical results obtained for these cases are tabulated"--Abstract, page ii.

Some Effects Of Selected Biodegradable Detergents On The Aeration Of Water And Activated Sludge, Donald Ernest Modesitt

Masters Theses

"The purpose of this study was to determine what effects the presence of selected biodegradable detergents have on the aeration of water and the activated sludge process for aerobic wastewater treatment. The detergents studied were LAS #1, Alfol, and Nalkylene. It was of particular interest to determine if these detergents decreased the oxygen absorptive capacities of water and wastewater. If detrimental effects were produced by the detergents it was then desired to determine if these effects were serious enough to create problems with aerobic wastewater treatment and aeration in receiving bodies of water.

A two liter volume of the liquids …

The Plastic Behavior Of Reinforced Concrete Beams With Varying Percentages Of Reinforcing Steel Symmetrically Placed, J. Leroy Hulsey

Masters Theses

"The purpose of this study is to determine the limitations of the plastic behavior of reinforced concrete beams with varying percentages of high strength steel (ASTM-A-432) cutoff in the compression region d distance beyond the point of inflection. Comparison was made with the derived equations.

Steel was placed symmetrically in order to obtain like action at critical sections. The members tested were of a propped beam nature having a total clear span of 5'6" with a 6" overhang on one end and 1'6" overhang on the other. Concentrated loads were applied so as to obtain midspan loading and fixed end …

Modification Of The Hydraulic Jump By Submerged Jets, Edward Leon Tharp

Masters Theses

"Tests were performed in order to determine the effect of submerged jets injecting water into the base of the hydraulic jump. The jump was studied in terms of the following properties: specific energy of the flow leaving the hydraulic jump, length of the hydraulic jump, tailwater depth, and wave formation properties. These properties for the hydraulic jump with submerged jets were compared to the natural hydraulic jump.

Results of the tests indicate that: submerged jets at any angle tested tend to decrease the specific energy of the water leaving the jump and are more effective than the impulse-momentum principle indicates, …

Analysis Charts For Single And Multi-Span Gabled Frames, John (Chung-Su) Ma

Masters Theses

"A method for analyzing single and multi-span gabled frames using analysis charts is presented. This method requires considerably fewer computations than methods previously used (such as the moment distribution and slope-deflection methods). Analysis charts are presented for single gabled frames having fixed or pinned ends at ground level, and charts are also presented which can be used to efficiently analyze multi-gabled frames.

The data for the analysis charts were obtained using matrix techniques in conjunction with the digital computer. These techniques are described"--Abstract, page ii.

Some Effects Of Sodium Pentachlorophenol On Activated Sludge And Minnows., James Albert Heidman

Masters Theses

"The primary purpose of this investigation was to determine the effect of sodium pentachlorophenol on activated sludge. An additional objective was to determine the toxicity of sodium pentachlorophenol to minnows.

All activated sludge units were grown on a glucose and mineral nutrient waste. In addition, a unit acclimated to 100 and 250 mg/1 of sodium pentachlorophenol was also studied. The effect of a shock loading of sodium pentachlorophenol was found to depend on the concentration of the loading and also on the group of micro-organisms which were predominating. One activated sludge system was seriously impared at a shock loading of …

Slope Stability Analysis Of A Fissured Glacial Clay, Byron G. Walker

Masters Theses

"A slope in an over-consolidated, fissured clay was analyzed by the Swedish Method of Slices.

Values of cohesion (c) and angles of friction (Ø) were determined by three different types of direct shear tests (undrained, drained and residual).

Factors of safety (functions of c and Ø) indicated that the direct shear test parameter gave a factor of safety approximately four times that represented by failure conditions in the field. Drained tests gave a factor of safety nearly 2.3 times the value represented by field conditions. The conclusion is made that these two tests are of limited value for slope stability …

Plastic Design Of Steel Frames For Minimum Weight, I-Chen Hung

Masters Theses

"The purpose of this study was to develop a method for weight minimization of the plastically designed frame, braced normal to its plane of action, and composed of prismatic steel members. The method accounts for the non-linear relationship between weight and moment capacity for both beams and columns. Reduction in the pure-bending fully-plastic moment in the presence of axial loading and both beam-column instability and overall frame instability due to sidesway are taken into account. Provision is made for minimization of frames employing standard sections as well as for frames whose built-up members may be chosen from a continuous spectrum. …

The Development Of A Modified Soil Shear Vane, Vernelle Truman Smith

Masters Theses

"The purpose of this investigation was to determine how the soil shear graph could be modified to measure more accurately values of shear strength of fine-grained, cohesive soils. Several modifications were tried, however, the one that gave the most satisfactory results consisted of a vane and base plate mechanism.

A red clay of high plasticity obtained from a local cave was tested in both the natural or undisturbed state and in the remolded state. The only variable was the moisture content. Compaction effort was the same for all remolded specimens. Tests were conducted on undisturbed samples taken with thin walled …

The Shrinkage Characteristics Of Plastic Clay, Edward De Santis

Masters Theses

"This investigation was conducted to determine the shrinkage properties of a clay soil whose structure had been artificially altered in the laboratory. Various percentages of dispersing and flocculating agent were added to the soil and the shrinkage curves plotted.

The shrinkage curves of the chemically treated soil were compared with those of the untreated soil. The values of the theoretical and observed shrinkage limits were also compared to determine the validity of the standard shrinkage limit test which, at present, does not take into consideration the structure of the soil.

An explanation of the differences in the shrinkage characteristics of …

An Investigation Of Consolidation On Compacted Partially Saturated Clarksville Soil, Ma-Tai Matthew Chen

Masters Theses

"The Terzaghi theory of consolidation and the assumption of his theory, pore pressure and effective stress, secondary compression and rheology were all reviewed and discussed. Eight compacted unsaturated samples made from Clarksville silty clay (CL) under different compaction efforts and moisture contents were subjected to consolidation load increments. Each load increment was maintained for 24 hours. An extra compacted sample was loaded for one month to investigate secondary compression.

From e-p curves, five settlement vs. compacted embankment height curves were derived for different compaction effort and moisture contents. These curves may be of practical use, when checked by field measurements …

The Effect Of Structure On The Consolidation Characteristics Of A Clay Soil, Dale E. Sukow

Masters Theses

"This paper reports the results of an investigation conducted to establish the effect of structure on the consolidation characteristics of a clay soil. Soil structure was caused to form in the soil by the addition of electrolytes to flocculate and disperse the clay fraction of the soil.

Consolidation tests were performed on specimens of the treated soil prepared at moisture contents well above the liquid limit of the soil. The consolidation data from these tests are evaluated and comparisons are made to relate the influence of structure to the consolidation characteristics of the treated soil.

The influence of structure on …

A Study Of Shear Failures In Footing, Fred V. Cole

Masters Theses

"The purpose of this investigation was to conduct a model study of the basic mechanism of failure in shear of reinforced concrete footings through the use of plaster models.

Sixty-nine models were constructed and loaded to failure on a foundation of sand using various combinations of size and depth of model and column size. Load - deformation data and failure loads were recorded.

It was determined that model studies are a feasible procedure to analyse the mechanism of failure in footings. The perimeter of the loaded area was found to be the critical section in determining the ultimate shearing strength …

Location Of Maximum Moments In A Continuous Two Span Beam Due To Moving Loads, Thomas Houng-Yn Yang

Masters Theses

"The objective of this investigation is to determine the positioning of vehicle wheels so as to cause maximum positive and negative moments in a two span continuous girder. Several variables are considered, namely, the ratio of loads to each other, the distance between wheels, and ratio of one span length to the other. The necessary equations are derived and the results, after being programmed on a computer, are shown in a series of curves.

These curves serve as a tool for the designer, enabling him to arrive at design moments by simple substitution in the appropriate moment expression, within the …

Analysis Of Sand Asphalt Mixtures, Maurice A. Sayegh

Masters Theses

"The objective or this investigation was to determine the optimum percent of asphalt which should be added to the sand asphalt mixture. Also the effects of filler on the properties or the sand-asphalt mixture were evaluated.

The variables in this study were mineral filler, asphalt cement, and asphalt content. The sand used in this study was sub-rounded, and uniformly graded. The asphalt was asphalt cement with two different penetrations, one of 85-100 penetration grade and the other of 120-150 penetration grade.

Three different groups of mixtures of sand-asphalt were prepared. The first group consisted of adding 85-100 penetration asphalt to …

The Effect Of Epoxy Resins On The Durability And Unconfined Compressive Strength Of An A-1b Soil, Guy H. Payne

Masters Theses

"This thesis reports the procedure and results obtained from the stabilization of a clean poorly graded sand with various amounts of epoxy resin. The same soil was also stabilized with varying amounts of Portland cement in order to have a basis for comparison of the results obtained. The sand used in this research came from the Meramec River in Central Missouri and is classed as an A-lb soil by the AASHO classification system. The following tests were performed on the stabilized samples: 1. Specimens were molded and compacted at 4%, 6%, 8%, 10% and 12% portland cement by weight of …

Fluid Flow In Pipes Of Rectangular Cross Sections, Bruce Harold Bradford

Masters Theses

"Head loss due to fluid friction was measured in smooth conduits of rectangular cross section. The data covers the laminar and turbulent range. Results were compared with previous theoretical and empirical data.

The customary practice of calculating head loss in non-circular conduits by use of the friction factor obtained on an “equivalent” circular pipe was discussed. It was found that this practice is successful in square cross sections undergoing turbulent flow. In laminar flow, however, this method is not accurate"--Abstract, page ii.

A Procedure For Analysis Of Three-Segment Symmetrical Balcony Beams, Ronald A. Hansen

Masters Theses

"A procedure for analysis of three-segment symmetrical balcony beams unsymmetrically loaded was derived whereby the normally complicated energy solution is eliminated. A moment distribution technique is used in the solution of the first and second phases of the problem. Tables are given to aid in determining the proper distribution factors. Due to the complexity of the third phase, a table of solutions is given for varying values of length, geometry, etc.. An example problem is also given demonstrating the use of interpolation within the tables"--Abstract, page ii.