Civil and Environmental Engineering Commons^™

Preface, Shamsher Prakash

International Conference on Case Histories in Geotechnical Engineering

No abstract provided.

Disclaimer, Multiple Authors

International Conference on Case Histories in Geotechnical Engineering

No abstract provided.

Conference Snapshots, Multiple Participants

International Conference on Case Histories in Geotechnical Engineering

No abstract provided.

Accelerated Consolidation Of Soft Clays Using Wick Drains, J. R. Davie, M. R. Lewis, L. W. Young Jr.

International Conference on Case Histories in Geotechnical Engineering

Construction of the New Istana for the Sultan of Brunei required that fill slopes up to 85 feet high be placed on very soft compressible floodplain soils. Wick drains installed in the soft sediments accelerated their consolidation and reduced long-term settlements. The consolidation also produced a strength increase in the soft soils that allowed the fill to be constructed without danger of a major base slip failure. Instrumentation installed in the floodplain soils provided data on excess porepressures built up during the fill placement, and on the resulting settlements. The measured porepressures and settlements were in good agreement with the …

Advances In The Construction And Design Of Jet Grouting Methods In South America, Giorgio Guatteri, Joseph L. Kauschinger, Antonio C. Doria, Edward B. Perry

International Conference on Case Histories in Geotechnical Engineering

This paper presents a brief historical development of the two most popular jet grouting methods used in South America, namely, the chemical churning pile method (CCP) and jumbo jet grouting. Advantages and limitations of each procedure are cited. A brief discussion follows covering the history of CCP jet grouting in South America. Field trials performed to improve the design methodology and construction of CCP and jumbo jet grouted columns are presented. Finally, three case histories are presented to illustrate the use of jumbo jet grouting where limited head room exists, jet grouting in close proximity to pile supported structures, formation …

Designing Geotextile Support For Submarine Power Cables, K. Y. C. Chung

International Conference on Case Histories in Geotechnical Engineering

Six 36 cm diameter submarine pipe-cables were buried in a 1.2 km long, fabric-lined trench in the soft river mud under 17 m average water head across the Hudson River about 4.8 km north of the Newburgh Bridge, New York. This paper describes the design considerations based on geotechnical point of view of using geotextile to support submarine power cables.

Geogrid Reinforced Soil Retaining Wall On Compressible Soils, R. L. Curtis, V. E. Chouery-Curtis, D. A. Miller

International Conference on Case Histories in Geotechnical Engineering

A geogrid reinforced soil wall with a wrap-around facing system was successfully constructed on soft, compressible alluvial and residual soils. An originally designed 20-foot (6.1 m) high, reinforced concrete cantilever retaining wall was not constructed because of the expected settlements induced by the wall and backfill. The geogrid reinforced wall was utilized because of its ability to withstand the estimated settlement and because it was considered less expensive than providing deep foundation support of a cantilever wall. This paper discusses the design, construction, and performance of the geogrid reinforced wall.

Geotechnical Studies Of Foundation Of A Tilted Tank At Parikshatgarh, India, G. C. Nayak, B. Singh, P. K. Jain

International Conference on Case Histories in Geotechnical Engineering

An overhead tank of 200 KL capacity and 9 m staging was constructed in year 1975 at the ancient historical site at Parikshatgarh, Meerut, India. The depth of foundation is 1.6 m and inner and outer diameters of annular raft is 6.8 m and 10.3 respectively. In year 1978, the overhead tank was observed to be tilted. Detailed geotechnical studies have been conducted in 1987 to find out the causes of tilting of the tank and tilts have been measured every month for last one year. It is interesting to note that in spite of severe tilt of 4.3 cm/meter …

Impact Of Tunneling On Two Brick-Bearing-Wall Structures, Marco D. Boscardin

International Conference on Case Histories in Geotechnical Engineering

The responses or a pair or brick-bearing-wall structures to nearby construction or twin, shield driven 21-ft-diameter tunnels in soil are examined. Horizontal and vertical ground displacements are summarized and discussed, as well as, horizontal and vertical displacements, tilting, distortion, and damage sustained by the structures. Transient features or the developing settlement trough and effects on building response are also examined and discussed.

Long Term Building Performance Over An Injected Subgrade, Ronald F. Reed, Paul Wright

International Conference on Case Histories in Geotechnical Engineering

Several foundation designs and stabilization methods are used with varying degrees of success to cope with the problem of expansive clays. Many of these methods are very expensive, therefore alternate technology that is both cost and performance effective has been developed. This paper presents a case history with pre- and post- stabilization test data for a 4-building project where pressure injection of lime and water was used to preswell weathered clay-shale to a depth of 10 feet. Use of pressure injection technology economically reduced post construction movements to 0.5 inches to 1.8 inches over a 7 year monitoring period. Movements …

Recent Examples Of Cut And Fill Reinforcement On A41-Highway In France, Trân Vô Nhiêm

International Conference on Case Histories in Geotechnical Engineering

At EVIRES PASS, between ANNECY and MONT BLANC in FRANCE, subsoil is made up of unstable clayey natural versants and marly bedrock affected by previous or current slidings. The problems encountered during the new A41-Highway construction were aggravated by the proximity of Road and Railway located on top of the same versant. The final Design consisted of succession of cuts and embankments with special soil reinforcement techniques to improve stability. So two existing unstable Railway embankments were promptly consolidated by "soil nailing" with driven steel dowel-piles which were either anchored or not. Two other high cuts in marls and sandstones …

Load And Resistance Factor Design Of Cold-Formed Steel Load And Resistance Factor Design Specification For Cold-Formed Steel Structural Members With Commentary, Ling-En Hsiao, Wei-Wen Yu, Theodore V. Galambos

CCFSS Library (1939 - present)

FOREWORD This progress report contains the following two parts: Part I: Load and Resistance Factor Design Specification for Cold-Formed Steel Structural Members (pp. i-101). Part II: Commentary on the Load and Resistance Factor Design Specification for Cold-Formed Steel Structural Members (pp. 103-148). The load and resistance factor design specification proposed herein is the revised version of the design recommendations prepared in September 1985 and submitted to American Iron and Steel Institute as Seventh Progress Report. This document was prepared according to the 1986 edition of the AISI Specification for the Design of Cold-Formed Steel Structural Members. The selections of ϕ …

Load And Resistance Factor Design Of Cold-Formed Steel: Calibration Of The Aisi Design Provisions, Wei-Wen Yu, Ling-En Hsiao, Theodore V. Galambos

CCFSS Library (1939 - present)

In the design of steel buildings, the "Allowable Stress Criteria" have long been used for the design of cold-formed steel structural members in the United States and other countries.' In view of the fact that the mathematical theory of probability, which has been so successfully applied in other fields of engineering, would seem to be equally applicable to cold-formed steel design by providing a more uniform degree of structural safety, the "Limit State Design" method based on the probabilistic concept has been used in Canada and Europe for the design of cold-formed steel structural members.' In the United States, a …

Load And Resistance Factor Design Of Cold-Formed Steel Comparative Study Of Design Methods For Cold-Formed Steel, Ling-En Hsiao, Wei-Wen Yu, Theodore V. Galambos

CCFSS Library (1939 - present)

Allowable Stress Design is the current method used to design cold-formed steel structural members and connections. In this design approach, factors of safety are used to compute the allowable design stresses which are compared to the actual maximum stresses that will occur in the member during the life of the structure. In recent years, the Load and Resistance Factor Design (LRFD) method has been developed for the design of hot-rolled steel shapes and the design of cold-formed steel structural members. This method is based on probabilistic and statistical techniques to account for the many uncertainties involved with the actual design. …

Design Of Cold-Formed Stainless Steel Structural Members Proposed Allowable Stress Design Specification With Commentary, Shin-Hua Lin, Wei-Wen Yu, Theodore V. Galambos

CCFSS Library (1939 - present)

INTRODUCTION This progress report on the design of cold-formed stainless steel structural members contains the following two parts: Part I: Proposed Specification for the Design of Cold-Formed Stainless Steel Structural Members (Third Draft). Part II: Commentary on the Proposed Specification for the Design of Cold-Formed Stainless Steel Structural Members (Second Draft). This project was sponsored by the American Society of Civil Engineers. The financial assistance provided by the Chromium Center, the Nickel Development Institute, and the Specialty Steel Industry of the United States is gratefully acknowledged. Special thanks are extended to members of the ASCE Steering Committee (Dr. Ivan M. …

The Distribution Of Chlorine And Iodine In Soil In The Vicinity Of Lead Mining And Smelting Operations, Bixby Area, S.E. Missouri, U.S.A., R. Fuge, M. J. Andrews, T. E. Clevenger, B. E. Davies, Nord L. Gale, C. F. Paveley, B. (Bobby) G. Wixson

Biological Sciences Faculty Research & Creative Works

Iodine and Cl are enriched in soils in the vicinity of the Magmont and Buick lead mines near Bixby, southeastern Missouri. The enrichments, up to 5.6 ppm I and 305 ppm Cl, are against regional background of 1.26 ppm I and 41 ppm Cl. The area of highest I and Cl is thought to reflect a zone of base metal sulphide mineralization occurring about 400 m below the surface. Iodine and Cl are also enriched in soils immediately adjacent to a tailings pond, hence these elements would appear to be leached from this source. A zone of enhanced I values …

Dynamic Timoshenko Beam-Columns On Elastic Media, Franklin Y. Cheng, Chris P. Pantelides

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Differential equations, stiffness coefficients, and fixed-end forces are formulated for a Timoshenko beam-column on an elastic foundation subjected to lateral time-dependent excitations and static axial loads. The theoretical formulation includes shear and bending deformations as well as rotatory inertia, with emphasis on two approaches. The two approaches differ in terms of the assumed shear component of the static axial load on the cross section. The first approach is based on the assumption that the shear component of the axial load is calculated from the total slope; in the second approach, the shear component of the axial load is calculated only …

Static Timoshenko Beam-Columns On Elastic Media, Franklin Y. Cheng, Chris P. Pantelides

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Two approaches are used to derive differential equations, stiffness coefficients, and fixed-end forces for the analysis of structural systems composed of Timoshenko beam-columns that may be supported by an elastic foundation. The analysis is for the evaluation of the critical static axial load and buckling mode-shapes of a structure with consideration of elastic media, bending, and shear deformations. The two approaches differ in terms of the assumed shear component of the static axial load on the cross section. The first approach is based on the assumption that the shear component of the axial load is calculated from the total slope, …

Behavior Of Reinforced Loess Specimens Under Triaxial Load, Mohammad Taghi Izadi

Masters Theses

"Effects of reinforcement on shear strength of a loessial (silty) soil arc studied. Unconsolidated undrained triaxial tests are performed on unreinforced and fabric reinforced soil specimens. Analyses of the test results showed that in general the shear strength of remolded loess specimens were improved substantially and increase in the shear strength was directly related to reinforcement spacing.

The mechanism of soil-reinforcement interaction and several existing analytical models are described. A modified analytical model based on enhanced confining theory is developed. This model can be used in assessing the effects of the reinforcement on shear strength of triaxial specimens. Comparison of …

Design Of Automotive Structural Components Using High Strength Sheet Steels Structural Behavior Of Members Consisting Of Flat And Curved Elements, M. Brad Parks, Wei-Wen Yu

CCFSS Library (1939 - present)

Local buckling of stiffened and unstiffened curved elements has been investigated both experimentally and analytically. Stiffened curved elements are supported along both longitudinal edges while unstiffened curved elements are supported along one longitudinal edge with the other longitudinal edge free. A series of stub column, beam, and shear tests have been performed for sections containing curved elements. The tested specimens were formed from sheet steels with yield strengths ranging from 27 to 88 ksi. The radius-to-thickness, R/t, values of the curved elements varied from 12 to 438 whereas the arc length-to-thickness, b/t, ratios ranged from 23 to 218. As a …

Steel Deck Institute, Inc. Design Manual For Composite Decks, Form Decks, And Roof Decks, Steel Deck Institute

Steel Deck Institute (SDI) Specifications and Manuals (1939 - present)

No abstract provided.

Soil-Shrinkage Induced Structural Failure, David Newton Richardson, Richard Wesley Stephenson, Daniel Molloy

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This Paper Describes an Investigation into the Causes of Structural Damage to a Retirement Home and the Subsequent Rehabilitation Project. the Investigation Revealed that the Damage Was Caused by Shrinkage of the Soils Beneath the Structure's Foundation as a Result of Dry Weather, Shrinkage-Prone Characteristics of the soils, Deviation from the Original Design, and Poor Construction Techniques. the Structure Was Subsequently Underpinned to Rock using the Inclined Drilled Pier Method. Interaction between Design and Construction Professionals is Also Presented. © ASCE.

Optimization Of Richardson's Shale Durability Rating System, John Dell Long

Masters Theses

"The two-cycle sieved slake durability test, performed on specimens initially oven-dried prior to testing, was determined to be the optimum slake durability testing procedure based on 12 variations of the test performed on 12 different shale types. The effects of changing slake durability testing variables was also studied.

Standard Proctor moisture-density and compaction-degradation tests were performed on 11 shales.

A modified version of the ultrasonic cavitation disaggregation test was developed and performed on 14 shales.

Richardson's shale durability rating equation was modified to include or reflect a data base of 14 shales, the results of the 20-min. ultrasonic cavitation disaggregation …

Structural Behavior Of Members Consisting Of Flat And Curved Elements, M. Brad Parks

Doctoral Dissertations

"Local buckling of stiffened and unstiffened curved elements has been investigated both experimentally and analytically. Stiffened curved elements are supported on all four edges while unstiffened curved elements are supported along three edges with one longitudinal edge free.

A series of stub column, beam, and shear tests have been performed for sections containing curved elements. The tested specimens were formed from sheet steels with yield strengths ranging from 27 to 88 ksi. The radius-to-thickness, R/t, values of the curved elements varied from 12 to 438 whereas the arc length-to-thickness, bit, ratios ranged from 23 to 218.

As a result of …

Development Of Design Criteria For Ferritic Stainless Steel Cold-Formed Structural Members And Connections, Pieter Van Der Merwe

Doctoral Dissertations

"This dissertation describes the development of the basic criteria needed for the design of structural members cold-formed from certain ferritic stainless steels. The Allowable Stress Design method as well as the Load and Resistance Factor Design method receive attention. The ferritic stainless steels under consideration are: Types AISI 409 and 430 as well as a modified Type 409 steel, designated 3CR12 steel, developed and produced by the speciality steel producing company, Middelburg Steel and Alloys in South Africa.

The mechanical properties needed for structural design are established. It is shown through an experimental study that the design provisions for the …

The New European Recommendations For The Design Of Light Gauge Steel Members, Per O. Thomasson

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.

Post-Yielding Strength Of Cold-Formed Steel Flexural Members, Muzaffer Yener

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.

Composite Slabs Subjected To Repeated Point Loading, R. M. Schuster, Ramadan E. Suleiman

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.

Cold-Formed Steel Compression Members Embedded In Grain, Ahmed Sabry, George Abdel-Sayed

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.

Web Crippling Strength Of High Strength Steel Beams, Chiravut Santaputra, M. Brad Parks, Wei-Wen Yu

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.