Civil and Environmental Engineering Commons^™

Buckling Behaviour Of Cold-Formed Steel Beams Under Bending And Torsion, Hong-Xia Wan, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This research is concerned with the buckling behaviour and design of cold-formed steel beams subject to combined bending and torsional actions. A finite element model considering the effects of initial geometrical imperfections and residual stresses was developed to simulate the combined bending and torsion of cold-formed steel beams. The finite element model was used to conduct analysis on cold-formed lipped channel sections, Z sections and hollow flange channel sections. Elastic buckling analysis was first conducted to study their buckling modes and buckling loads. Nonlinear analysis including the effects of large deformation and material yielding was conducted to obtain their ultimate …

Finite Element Investigations Of The Effect Of Residual Stress In Cold-Formed Sigma Beams, Feiliang Wang, Jian Yang

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Press braking is a cold forming operation used to fold the angle along the flat sheet between the top punch and bottom die. The residual stress will be induced in this process as a result of plastic deformation. In the welding process, a dynamic thermal cycle is introduced to generate a non-uniformly temperature distribution on the heat affected zone (HAZ), and the residual stress also occurs in the process as a result of uneven cooling along the welding bead. The existence of residual stress can superimpose onto the external loadings to affect the stiffness and load resistance capacity of the …

Incorporation Of Elastic Local Buckling In A Plain Channel Section Beam Subjected To Double-Curvature Bending: An Effective-Width Approach, Edwin Lim, Barry J. Goodno, James I. Craig

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

When electrical cabinets are subjected to lateral loads, such as earthquakes, the beams of the cabinet frame typically experience double-curvature bending deformation. These beams are usually constructed from cold-formed plain channel sections so they are vulnerable to elastic local buckling near their ends, where high stresses from applied loads are more likely to develop. To capture local buckling behavior, structural engineers typically use high-fidelity finite element models, but this approach can be complex and computationally expensive. A Timoshenko beam element model is simpler and less computationally costly but it is not capable of capturing local buckling behavior. In this paper, …

Tests Of Cold-Formed Ferritic Stainless Steel Beams, Lianghao Li, Ben Young

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Ferritic stainless steel is characterized by its low or even no nickel content, which provides a good alternative to a more commonly used austenitic stainless steel (with 8.0-10.0% nickel content) in structural application. The low nickel content attributes to low initial material cost and more stable price for ferritic stainless steel. A series of four-point bending tests was conducted on both square and rectangular hollow sections to investigate the flexural performance of cold-formed ferritic stainless steel hollow sections. The experimental results obtained from this test program and the available data in the literature on cold-formed ferritic stainless steel beams were …

Lateral-Torsional Buckling Of General Cold-Formed Steel Beams, Robert S. Glauz

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The design of unbraced cold-formed steel beams must consider lateral-torsional buckling due to the low torsional stiffness associated with open cross-sections. The American Iron and Steel Institute incorporated design equations for the critical elastic lateral-torsional buckling stress in the North American Specification for the Design of Cold-Formed Steel Members. These equations are based on elastic theory for singly-symmetric and doubly-symmetric sections. However, the equation for point-symmetric sections is only a rough approximation. Furthermore, there are no provisions for lateral-torsional buckling of non-symmetric sections, or sections oriented to non-principal axes. This paper investigates and develops a general formulation of the lateral-torsional …

Unconstrained Cross-Sectional Shape Optimisation Of Cold-Formed Steel Beams And Beam-Columns, Bin Wang, Benoit P. Gilbert, Guillaume L. Bosco, Hong Guan, Lip H. Teh

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper is focused on optimising the cross-sectional shapes of simply-supported, singly-symmetric and open-section cold-formed steel (CFS) beams and beam-columns without manufacturing or assembly constraints. A previously developed Genetic Algorithm (GA) is used in this study. Fully restrained and unrestrained beams against lateral deflection and twist, as well as unrestrained beam-columns are optimised, of which the nominal member capacities are determined by the Direct Strength Method (DSM). The optimised cross-sectional shapes are presented and the evolution of the unrestrained cross-sectional shapes for various combinations of axial load and bending moment is analysed and discussed.

Identifying Shear Buckling Coefficients For Channels With Rectangular Web Stiffeners Using The Generalised Cfsm, Morgan A. Rendall, Gregory J. Hancock, Kim J. R. Rasmussen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The Direct Strength Method (DSM) of design for cold-formed sections was recently extended in the North American Specification for Cold-Formed Steel Structural Members (NAS S100:2012) to include members in shear. The method has largely been developed on the basis of work done on lipped channel sections. To utilise the method requires the critical shear buckling load of the section, which may be determined from a minimum point on the signature curve for the section in pure shear. However when longitudinal web stiffeners are added to the channel a minimum may not exist, or may occur at half-wavelengths where the critical …

A Direct Strength Method (Dsm) Of Design For Channel Sections In Shear With Square And Circular Web Holes, Song Hong Pham, Cao Hung Pham, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The Direct Strength Method (DSM) design rules for cold-formed steel members in shear have been incorporated recently into the North American Specification (AISI S100-12) and are being implemented in the Australian standard (AS/NZS 4600:2005). The method, which was calibrated for unperforated members only, requires two inputs including the buckling load Vcr and the shear yielding load Vy. For members with square web cut-outs, Vcr can be computed by either the Spline Finite Strip Method (SFSM) or the tabulated values based on the shear buckling coefficients kv as studied by CH Pham or the Finite Element Method (FEM). However, Vy has …

New Sdi Diaphragm Design Manual, Larry Luttrell, John Mattingly, Walter Schultz, Thomas Sputo

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The Steel Deck Institute (SDI) has released the new and long awaited 4th Edition of the Diaphragm Design Manual (DDM04). This new edition complies with the requirements of the ANSI/AISI S310-13 North American Standard for the Design of Profiled Steel Diaphragm Panels. At 408 pages, the 4th Edition is larger than its predecessor and will be an invaluable resource to structural designers because of the background information, design examples, and extensive load tables.

The First Edition of the DDM, published in 1981, was authored by Dr. Larry Luttrell, P.E., the Technical Advisor to the SDI. The diaphragm design method developed …

Recent Developments In The Australian/New Zealand Standard As/Nzs 4600 For Cold-Formed Steel Structures, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The Australian/New Zealand Standard AS/NZS 4600 is currently under revision based in part on the latest edition of the North American Specification AISI S100:2012 and partly based on the latest research in Australia and New Zealand. The Direct Strength Method (DSM) of design has undergone substantial research since the 2005 edition of AS/NZS 4600 and this research is now incorporated in the revised edition. The new areas in the DSM include shear, combined bending and shear, combined bending and compression, sections with holes and inelastic reserve capacity. Further, the prequalified sections now include most sections with longitudinal web and flange …

Progress In The Development Of Asce 41 For Cold-Formed Steel, Deniz Ayhan, Robert L. Madsen, Benjamin W. Schafer

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The objective of this paper is to document progress on new cold-formed steel provisions for the forthcoming edition of ASCE 41, Seismic Evaluation and Retrofit of Existing Buildings. The current edition of ASCE 41 (2013) is weak with respect to the application of cold-formed steel and provides only limited information on cold-formed steel framed buildings, shear walls, members, and connections. The emphasis in this paper is on cold-formed steel framed shear walls, and the development of modeling parameters that characterize the backbone shear-deformation response, and acceptance criteria that provide allowable demand-to-capacity ratios (m-factors) for the shear walls based on a …

Aisi Standards Developed And Updated In 2015 And 2016, Helen Chen, Roger Brockenbrough, Richard Haws

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

During 2015 and 2016, AISI developed framing standards were consolidated and updated, the North American Specification was updated and reorganized in format, and two new test standards were published. This paper provides an overview of the reorganized standards and major changes, and a brief introduction to the newly developed test standards.

Advancing Bim For Cold-Formed Steel Structures, Adam Johnson, Roni Ramirez, Cheng Yu

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper presents a research project aimed at advancing BIM for cold-formed steel (CFS) structures. The creation of the CFS family for Autodesk Revit is a handy solution for the lack of CFS members and information inside the Autodesk Revit libraries. Revit is one of the industry’s standard software for producing building information models. To overcome the disadvantages of not having CFS members in Revit, this research project focused on two phases to reach completion. Phase one consisted of developing a BIM library of industrial standard CFS members such as studs, tracks, and channels. Parameters were added to the members …

The Design And Development Of New Cold Roll Formed Products By Finite Element Modeling And Optimisation, V. B. Nguyen, P. K. C. Wood, M. A. English, M. A. Castellucci

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The design and development of new cold roll formed products can incur significant cost and the product may not be optimised for either performance or manufacture. This paper describes a new method to develop an optimum structural design of profile by cold roll forming using a combined approach of finite element analysis and optimisation techniques. To illustrate the concept, the design and development of a new channel beam and a new drain grating subjected to bending are presented. The two case studies, demonstrate how a roll formed profile may be optimised to improved structural performance through use of stiffeners and/or …

Buckling Strength Of Cold-Formed Circular Steel Column Subjected To Axial Load, Ayana Ito, Nobutaka Shimizu, Keiichi Sato, Yoshimichi Kawai

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

In this study, the global buckling behavior of a cold-formed circular steel column was discussed with a focus on the effects of its mechanical properties and initial imperfections on the behavior. As the first step, the stress–strain curves of the column under tensile and compressive loads as well as its residual stresses were investigated. Subsequently, a finite element analysis was conducted to clarify if the analysis properly simulated the stub column behavior. The analysis results obtained using measured compressive stress–strain curves and residual stresses agreed well with experimental results. Finally, another finite element analysis was performed on the long column …

Proposal For Codification Of A Dsm Design Approach For Cold-Formed Steel Short-To Intermediate Angle Columns, Pedro Borges Dinis, Dinar Camotim

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper presents a proposal for the codification of an efficient design approach for cold-formed steel short-to-intermediate equal-leg angle columns, consisting of a slight modification of a design approach developed by Dinis & Camotim (2015) and based on the Direct Strength Method (DSM). After (i) collecting the available experimental and numerical failure load data, comprising fixed-ended and pin-ended columns with several geometries (cross-section dimensions and length) and reported by various researchers, and (ii) briefly reviewing the mechanical reasoning behind the proposed procedures, the search for new/simpler expressions to provide the DSM design curves is addressed. Their merits are assessed through …

Effect Of Web Perforation On The Behaviour Of Cold-Formed Steel C-Shape Slender Column Subjected To Non-Uniform Cross-Sectional Distribution Of Elevated Temperatures, S. Yang, L. Xu

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Presented in this paper is a numerical investigation on the effect of web perforations on the behaviour of cold-formed steel C-shape columns subjected to non-uniform cross-sectional distribution of elevated temperature with use of finite element analysis. The length of web perforation investigated varies from 0 mm to 630 mm (25 in.). The non-uniform cross-sectional distributions of elevated temperatures are obtained from finite element thermal analysis of insulated CFS walls subjected to standard fire up to 105 minutes. Sequentially coupled thermal-stress analyses were carried out under a transient state condition. The concentrically loaded cold-formed steel C-shape columns with load ratios of …

Distortional Buckling Experiment On Cold-Formed Steel Lipped Channel Columns With Circle Holes Under Axial Compression, Xingyou Yao, Yanli Guo, Zhen Nie

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The objective of this paper is to research the distortional buckling mode and load-carrying capacity of cold-formed thin-walled steel columns with circle holes in web. Compression tests were conducted on 26 intermediate length columns with and without holes. The test members included four different kinds of circle holes. Test results show that the distortional buckling occurred for intermediate columns with holes and the strength of columns with holes was less than that of columns without circle hole. The ultimate strength of columns decreased with the increase of the total transverse width of hole in cross-section of members. For each specimen, …

Dsm For Web Crippling Under Two-Flange Conditions, Pedro Natário, Nuno Silvestre, Dinar Camotim

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper summarizes recent investigations on the development of Direct Strength Method (DSM) for the design of cold-formed steel beams under two-flange (TF) loading against web crippling failure. Recently, the authors proposed a new approach to predict the web crippling failure load of cold-formed steel beams under External Two Flange (ETF) and Internal Two Flange (ITF) loadings using DSM. Firstly, existing experimental test data are summarized and then the accuracy of North-American Specification (AISI 2012) and Eurocode 3 (CEN 2006) provisions is briefly assessed. In order to obtain additional information on the web crippling behavior of each test specimen, non-linear …

Experimental Investigation Of Cold-Formed C-Sections With Central Square Holes In Shear, Cao Hung Pham, Andreas Pelosi, Thomas Earls, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The North American Specification S100:2012 Edition has recently included DSM design rules for unperforated channel sections in shear. However, there are no rules presented in this standard for the DSM in shear for sections with holes. Recently, a testing program has been performed at the University of Sydney to determine the ultimate strength of high strength cold-formed C-sections with a thickness of 1.5 mm and central square holes of varying sizes. Three different sizes of the square holes were chosen for testing. For thin sections, the DSM shear curve was found to be applicable for design of sections with square …

North American Standard For The Design Of Profiled Steel Diaphragm Panels, 2016 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

North American Specification For The Design Of Cold-Formed Steel Structural Members, 2016 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Direct Strength Prediction Of Cold-Formed Steel Beam-Columns, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The Direct Strength Method (DSM) of cold-formed steel member design employs local, distortional, and global cross-section elastic buckling analysis with empirically derived “direct” expressions to predict member strength. DSM is an accepted design method in national design specifications (e.g., AISI-S100-16) and enables a unified, robust, and flexible design approach. However, for beam-columns DSM in current design specifications employs simplified linear interaction expressions based on combining the isolated axial and bending elastic buckling and strength response. Today, local, distortional, and global elastic buckling under any combination of axial load and bending moments may be found using elastic buckling analysis tools such …

Elastic Field And Frequency Variation In Extendable Wind Turbine Blades, Jeswin John, Donald W. Radford, Subhas Karan Venayagamoorthy, Paul R. Heyliger

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The behaviors of tip displacement, maximum stress, and natural frequency of vibration as a function of blade length are investigated for extendable wind turbine blades. A three-dimensional linear elasticity finite-element model of the blade is used along with a typical profile and representative material properties. The quasi-linear response and free vibration behavior are investigated for a sequence of blade geometries. These estimates are intended to give approximate measures of expected changes in the elastic and dynamic field as the operating length changes and provide preliminary guidelines for this novel class of structure.

The Bridge Newsletter Winter 2016, Missouri University Of Science And Technology

The Bridge Newsletter

-World's only cold-formed steel conference
-2016 Alumni of Influence
-National intelligence leader speaks
-Senne Memoria

Membership Of Forum For Promotion Of Soil Dynamics In India, Shamsher Prakash

Forum for Promotion of Soil Dynamics in India

No abstract provided.

Minutes Of The Fourth Meeting Of The Forum For Promotion Of Soil Dynamics In India, Shamsher Prakash

Forum for Promotion of Soil Dynamics in India

No abstract provided.

Theoretical Study Of Two States Reactivity Of No Activation On Iron Atom, Xiaoman Wang, Yaxin Su, Wenyu Liao, Wenyi Deng

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The mechanism of Fe+NO was calculated by the Density Functional Theory (DFT) with the B3LYP methods combined with the 6-311+G (d, p) basis set. The geometry of reactants, transition states, intermediates and products of two reaction systems were completely optimized, and all the transition states were verified by the vibration analysis and intrinsic reaction coordinate (IRC) calculations. The "Two State Reactivity (TSR)" was used to analyze the reaction mechanisms; Results showed that the reaction system preferentially involves low-spin state entrance channel and the high-spin state exit channel. In the reaction channel, the crossing point appears, which would effectively reduce the …

Characterization Of Cfs Framed Diaphragm Behavior, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

Knowledge of the in-plane response to loading of cold-formed steel (CFS) framed diaphragm structures is essential for seismic and wind design. The information available specific to diaphragm design in the North American CFS design standards (AISI S240 & S400) is based on limited experimental work and the extrapolation of design methods developed for the wood industry. To address this shortcoming a test-based research project was performed in the Jamieson Structures Laboratory at McGill University focusing on the characterization of the behaviour under in-plane loading of CFS framed - wood sheathed diaphragms. This research was a complementary study to a research …

Methamphetamine Absorption By Skin Lipids: Accumulated Mass, Partition Coefficients, And The Influence Of Fatty Acids, K. Parker, G. Morrison

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Occupants of former methamphetamine laboratories, often residences, may experience increased exposure through the accumulation of the methamphetamine in the organic films that coat skin and indoor surfaces. The objectives of this study were to determine equilibrium partition coefficients of vapor-phase methamphetamine with artificial sebum (AS-1), artificial sebum without fatty acids (AS-2), and real skin surface films, herein called skin oils. Sebum and skin oil-coated filters were exposed to vapor-phase methamphetamine at concentrations ranging from 8 to 159 ppb, and samples were analyzed for exposure time periods from 2 h to 60 days. For a low vapor-phase methamphetamine concentration range of …