Civil and Environmental Engineering Commons^™

Development And Validation Of An Analytical Modeling Tool For Solar Borehole Heat Exchangers, Adam Ornelles

All Theses

Current numerical modeling solutions used for subsurface heat flow, such as the Berkeley TOUGH codes, are often difficult to use and time-consuming compared to analytical modeling methods. However, current analytical modeling methods for subsurface heat flow and groundwater cannot accurately model the subsurface in 3 dimensions, a feature paramount to the planning and installation of thermal borehole heat exchangers used in environmental remediation.

This research developed a novel 3-dimensional analytical modeling tool for solar-powered borehole heat exchangers. The analytical modeling tool can plan thermal remediation systems while being more straightforward to operate than current numerical modeling software. By creating a …

Chasing Target Zero: Contributing Factors Of Fatal Crashes In South Carolina, Matthew Stanley

All Theses

South Carolina consistently ranks in the top-10 in fatal crashes per 100,000 capita and 100 million vehicle miles traveled. This thesis summarizes an analysis of contributing factors for fatal crashes in South Carolina. A primary objective of this thesis is to investigate differences in contributing factors for fatal crashes as compared to all crashes in South Carolina. 2018 South Carolina fatal crashes (N=970) and all crashes (N=152,973) were analyzed and compared using classic Venn diagrams to compare differences in contributing factors between fatal crashes and all crashes. Fatal, non-fatal, and all crashes were aggregated into one of seven possible contributing …

Effect Of Long And Short Chain Fatty Acids On Methane Yield And Microbial Community Composition In Anaerobic Co-Digestion, Emmaline Spier Camposano

All Theses

Fats, oils and greases are produced from a variety of industries, including animal rendering operations, vegetable oil processing plants and the hospitality industry. These hydrophobic, COD-rich compounds are known to cause issues in municipal wastewater collection and treatment systems. Anaerobic co-digestion has been shown to be an effective way to treat FOG and presents an opportunity to produce greater quantities of biogas. However, many microorganisms are sensitive to the degradation products of FOG, including long and short chain fatty acids. Two studies were performed to address potential inhibitory effects of both.

The first study co-digested various percentages of FOG with …

Development And Promotion Of Mass Timber Noise Barrier For Highways, Harsh Bothra

All Theses

Highways are some of the biggest causes of noise pollution in the United States of America. To deal with the traffic noise coming from these highways, noise barriers have been erected across major highways. The goal is to reduce as much noise as possible through a sustainable solution. Unfortunately, the use of steel and concrete, commonly used materials, have undesired environmental impacts. A suggested sustainable alternative material would be mass timber. Mass timber products such as cross-laminated timber (CLT) and mass plywood panels (MPP) has attracted the attention of the construction industry in the U.S, as they are sustainable, light, …

Development Of Lambda Factors For Masonry Design With Lightweight Grout, Rumi Shrestha

All Theses

Reduction in structural mass, improvement in thermal performance, and reduction in shrinkage cracking through internal curing are some of the reasons that lightweight (LW) aggregates have been used in structures and pavements for decades. However, lightweight grout is still not permitted for use in reinforced masonry construction by the TMS 402/602-16 code. In order to realize the benefits of lightweight grout in U.S. reinforced masonry construction, a codified procedure for its use is required which must be informed by experimental testing.

This research is a pilot project directed to characterize the performance of LW grout in comparison to normal weight …

The Effect Of Using Palm Oil As An Electron Donor For The Reductive Dechlorination Of Trichloroethylene (Tce), Shivani Swamy

All Theses

TCE is currently remediated using physical methods like air stripping and granular activated carbon adsorption. While physical and chemical processes work on a site-specific basis, biological strategies have been favored as they are economical and reliable. The objective of this work was to determine the feasibility of using palm oil as an electron donor in the reductive dechlorination of TCE to ethene. Palm oil was considered for the study because it is locally grown in many parts of the world. The palm oil that does not meet the industry standards is discarded. Despite the environmental impacts caused by the palm …

Theoretical Development And Numerical Validation Of An Asymmetric Linear Bilateral Control Model For An Automated Truck Platoon, M Sabbir Salek

All Theses

In this study, the author theoretically develops and numerically validates an asymmetric linear bilateral control model (LBCM) for an automated truck platoon, in which the motion information (i.e., position and speed) from the immediate leading truck and the immediate following truck are weighted differently. The novelty of the asymmetric LBCM is that using this model, all the follower trucks in a platoon can adjust their acceleration and deceleration to closely follow a constant desired time headway at all times to improve platoon operational efficiency while maintaining local and string stability. The author theoretically proves the local stability of the asymmetric …

Deriving Generalized Temperature-Dependent Material Models For Masonry Through Fire Tests And Machine Learning, Aditya Avinash Daware

All Theses

Masonry is one of the oldest and commonly used building materials in the construction industry. Among a variety of benefits, masonry provides low-cost construction, fire, and weather protection as well as thermal and sound insulation. In addition, masonry has superior material properties at elevated temperatures which is reflected by its slow degradation of its mechanical and thermal properties. Literature shows that we do not have a uniform material model that describes the mechanical degradation of masonry under fire conditions. As such, this limits the use of masonry in fire-based performance design of masonry structures. To bridge this knowledge gap, this …

Seismic Performance Assessment Of Building Contents: Monetary Losses And Injuries, Sereen Majdalaweyh

All Dissertations

Building contents include all the components that are not attached to the building which the owners place after the construction phase, such as furniture, electrical equipment, glassware, and other personal items. Loss and damage assessment of building contents proved to be challenging in performance-based earthquake engineering frameworks because of the data sparsity. Damages to building contents during an earthquake not only cause monetary losses; tumbling and over-toppling of heavy building contents could result in injuries and even deaths of occupants. While major advancements have been made in performance-based earthquake engineering; however, the focus is mainly on damages and collapse risk …

The Professional Constructor, Full Issue, Volume 46, Number 02

The Professional Constructor

No abstract provided.

Evaluation Of In-Cab Air Quality For Nonroad Diesel Construction Equipment, Phil Lewis, Sherif El Khouly, Adam Mayer, Jeremy Johnson

The Professional Constructor

Previous research indicates that air quality near the cabs of nonroad diesel equipment may exceed recommended exposure limits for certain pollutants. The objective of this case study was to collect and analyze air pollutant data near the cabs of nonroad diesel equipment while performing real world activities. Using state-of-the-art instrumentation, the research team conducted 24 tests on nine different items of nonroad equipment. The team collected data related to pollutant concentrations of carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, particulate matter, and black carbon. Average concentrations of carbon monoxide and nitric oxide did not exceed published exposure limits on …

Prefabrication In Buildings With Focus On Emerging Mep Rack Systems, Mark Daniels, M.G. Matt Syal

The Professional Constructor

The growth in technology and automation has influenced the construction industry to explore prefabrication alternatives in building design and construction. In addition, the shortage of skilled labor is accelerating the push for the adoption of prefabrication in building industry. This paper provides an overview of the present construction market and labor trends and summarizes various levels and categories of prefabrication. It then provides detailed information on an emerging MEP prefabricated solution known as the MEP rack systems. The implementation of the MEP rack systems is discussed with the help of a hospital case study project. It concludes with the discussion …

Case Study Of Using Unmanned Aircraft Systems To Support Bridge Inspections, Joseph M. Burgett, Gurcan Comert

The Professional Constructor

This paper presents the results of a case study conducted to evaluate the potential benefit of unmanned aircraft systems (UAS), commonly referred to as drones, as a tool to improve the bridge inspection workflow. The study conducted two experiments to determine how well deficiencies could be detected using a UAS. Both experiments were conducted using the same test bridge. The first experiment was carried out by the bridge inspection engineers (BIEs), who had previously inspected the bridge using traditional methods. They used the drone to search for inspection points identified in the inspection report. The second experiment was conducted by …

Stick Built Vs. Panelize Wall/Truss Framing For New Home Construction: A Time Study Labor Comparison., Eric A. Holt, Jim Anzlovar, Alexander Welsh

The Professional Constructor

Due to many trends in the construction industry (material cost increase, labor shortages, supply chain issues, pandemic, market demand outpacing supply), the homebuilding industry is looking for alternative ways to frame homes. In response to the National Housing Endowment (NHE) Request for Proposal, the researchers reviewed the literature on the housing market’s current state regarding the scale and scope of the skilled construction framers shortage and the current market share of single-family framing method; stick-built vs. panelization. Working with industry part ners, the team analyzed time studies for multiple new home builds. It was found that panelized wall framing systems …

Minority And Female Participation In Construction Industry Apprenticeship Programs, Richard Bruce, Aaron Sauer, Patrick Sells, Curtis Bradford

The Professional Constructor

According to the U.S. Bureau of Labor Statistic’s Current Population Survey, nearly 90 percent of the 10.7 million people employed in the construction industry are white males (2021). This statistic will remain unchanged unless more minorities and females are recruited into the industry. For craft workers, a primary recruitment mechanism is the registered apprenticeship program. This study analyzes the U.S. Department of Labor’s Registered Apprenticeship Database (RAPIDs) from 2000 to 2019 to identify trends for new apprentices. The study found that there was no change in the proportion of new female apprentices in the previous 20 years and no change …

Quantification Of Compound And Cascading Hydroclimatic Extreme Events, Sourav Mukherjee

All Dissertations

Compound and cascading hydroclimatic extreme events have garnered much attention in recent studies. The combined effects of interconnected extremes can cause widespread damage, with a higher potential impact than individual extremes. Both anthropogenic warming and natural climate variability affect these extremes, which is why detecting past extreme events, understanding the underlying mechanisms, and assessing their future impacts can aid in mitigation efforts to reduce their overall impact. However, thus far, identifying such events is oversimplified and the propagation of their impact as cascades from the physical to human systems remains partly explored.

The overreaching goal of this thesis is to …

6th Aawe Workshop Program - Conference Proceedings, Nigel Kaye

American Association for Wind Engineering (AAWE) Workshop

The Glenn Department of Civil Engineering at Clemson University is hosting the 6th AAWE Workshop with a focus on student and early career presentations. The workshop will include several keynote addresses and panel discussions on non-academic wind engineering careers and future directions for wind engineering research.

The Professional Constructor, Full Issue, Volume 46, Number 01

The Professional Constructor

No abstract provided.

How New, Innovative Technology Can Be Implemented To Combat The Construction Industry Labor Shortage, Noah David Jackson

The Professional Constructor

This essay addresses the construction industry’s need to compensate for the current and projected labor shortage through innovative technologies. In the first portion of this essay, three technologies that are most feasible for implementation – the Internet of Things (IoT), Drones, and Prefabrication – are detailed. The challenges faced are then discussed before the second major portion in which steps for implementation are outlined. These steps include forming partnerships, learning the process, communicating, training, implementing, and adapting and improving. The essay concludes with a discussion of how the AGC organization, and members within, can aid the industry in meeting this …

The Adaptative Construction Industry, Rhett Cox

The Professional Constructor

The construction industry is an industry that always unites to find ways to solve problems. It is very complex and requires considerable organization, hard work, specific skills, and a whole lot of determination. In this paper, I will discuss three ways that the industry is making strides to make construction better and more efficient: (a) increased use of modular construction and prefabrication, (b) use of drones, and (c) Building Information Modeling (BIM) use. With the construction process becoming more and more complex, improving efficiency and safety has gained more attraction, especially when coping with fundamental issues such as labor shortage, …

How New, Innovative Technology And Project Execution Tools And Techniques Can Be Used To Improve The Construction Process (Including Safety And Efficiency), James L. Craig

The Professional Constructor

Humanity has often sought to utilize tools and technology to make working faster, more efficient, more comfortable, and more accurate. While humans may have started with stone tools, we have since developed complex and sophisticated mechanical and digital technologies. The construction industry has been utilizing construction technology and equipment for these same reasons for generations. While other industries have embraced the use of smart, autonomous technology and robotics, the construction industry has steadily fallen behind in this effort. In this paper, I will discuss current work using these tools and possible applications for future development.

The Impact Of Climate Change On Building Energy Demands And Mitigation Measures In Florida, Aiyin (Erin) Jiang

The Professional Constructor

Tropical and subtropical parts of the world are projected to be the most vulnerable to the impact of climate change on building energy consumption demand. Few studies, however, focus on all four greenhouse emission scenarios defined by International Panel of Climate Change, which would be useful in assessing the energy demand challenges areas such as Florida. This study applies the most recognized climate change model downscaling approach, the morphing method, to investigate the impact of climate change on the commonly used commercial buildings in Florida’s climate zones under all four emission scenarios. It also analyzes the efficacy of various mitigation …

Frequency And Magnitude Of Cost Growth In Public Works Contracts, George Fulton, Panagiotis Mitropoulos

The Professional Constructor

Cost overruns are a persistent issue in the construction industry. This paper investigates factors that may drive cost growth on public works contracts. The study collected data on 1,043 public works projects completed over a three year period. The analysis examined the impact of four factors on cost overruns: (1) Project type, (2) Contract size, (3) Contract duration, and (4) Construction placement (value per day). The data were analyzed using a combination of basic descriptive statistics along with statistical hypothesis testing of means for various factors affecting cost growth. Cost growth was found to vary significantly by project type, contract …

Case Study Of Real-World Emissions Rates Verus Epaemission Standards For Motor Graders, Boshra Karimi, Phil Lewis

The Professional Constructor

Using the Volkswagen emissions scandal as motivation, the purpose of this case study was to investigate whether or not heavy-duty diesel construction equipment exceeds EPA emissions standards for nonroad diesel engines. The equipment analyzed included four separate motor graders with EPA emissions standards Tier 0, Tier 1, Tier 2, and Tier 3 engines. The analysis was based on a dataset of real-world emissions rates collected from in-use equipment on actual jobsites. The results showed that mass per time emissions rates for hydrocarbons, carbon monoxide, nitrogen oxides, and particulate matter decreased as the EPA emissions standards became more stringent. Furthermore, there …

Understanding Sub-Contractor Selection Factors In Thebuilding Construction Industry For The Southeastern United States, Dhaval Gajjar, Cayla Anderson

The Professional Constructor

The primary entities within building construction industry consists of the owner, the architect / engineer, and the general contractor, that ensure the success of any construction project. On a traditional project, the owner selects and contracts with the general contractor to construct a building designed by the architect. A considerable amount of research has been conducted to understand the owner’s selection factors to hire a qualified general contractor. However, the general contractor selected for the project seldom self-performs the entire construction of a building. The general contractor might self-perform some aspects of the actual building construction, but they will typically …

Investigating The Impacts Of Crash Prediction Models On Quantifying Safety Effectiveness Of Adaptive Signal Control Systems, Weimin Jin, Mashrur Chowdhury, Sakib Mahmud Khan, Patrick Gerard

Publications

Introduction: Adaptive Signal Control System (ASCS) can improve both operational and safety benefits at signalized corridors. Methods: This paper develops a series of models accounting for model forms and possible predictors and implements these models in Empirical Bayes (EB) and Fully Bayesian (FB) frameworks for ASCS safety evaluation studies. Different models are validated in terms of the ability to reduce the potential bias and variance of prediction and improve the safety effectiveness estimation accuracy using real-world crash data from non-ASCS sites. This paper then develops the safety effectiveness of ASCS at six different corridors with a total of 65 signalized …

Adaptive Signal System Safety Impacts Final Report, Mashrur Chowdhury, Weiman Jin, M. Sabbir Salek, Sakib Mahmud Khan, Katherine Brunk, Patrick Gerard, Nathan Huynh, Mohammad Torkjazi

Publications

The research team conducted a literature review and a nation-wide survey at the beginning of the research. The literature review revealed that Adaptive Signal Control System (ASCS) was effective in reducing crashes in some studies, while in other studies, the crash reduction due to ASCS was not statistically significant. Twenty-eight states participated in the nation-wide survey and helped the research team identify corridor characteristics, such as the design speed and Annual Average Daily Traffic (AADT) of an ASCS corridor, which would allow for the best operational and safety outcomes. Then, to determine the safety effects of ASCS, the research team …

Development And Application Of Sustainable Binders Comprising Of Fly Ash And Ground Glass Fibers In Portland Cement And Geopolymer Concrete, Omar Alsanusi Amer

All Dissertations

Since cement production is responsible for a significant share of anthropogenic CO2 emissions, the sustainability of concrete construction has become one of the most targeted research and construction industry goals. Many suggestions have been in use to encourage sustainability of concrete construction; one such approach is to partially replace cement by industrial byproducts. The most known industrial byproduct used in concrete construction worldwide has been fly ash, which is a byproduct of burning coal for power generation.

Fly ash use in concrete has various benefits. It reduces the water demand, reduces plastic shrinkage, reduces permeability, and thus improving the durability …

The Professional Constructor, Full Issue, Volume 45, Number 02

The Professional Constructor

No abstract provided.

A Probabilistic Casualty Model To Include Injury Severity Levels In Seismic Risk Assessment, Weichiang Pang, S. Majdalaweyh, A. Safiey, K. Rokneddin, S. Prabhu, M. Javanbarg, E. Ziaei

Publications

Despite the increasing adoption of Performance-Based Earthquake Engineering (PBEE) in seismic risk assessment and design of buildings, earthquakes resulted in around 1.8 million injuries (three times the number of fatalities) over the past two decades. Several existing PBEE-based methodologies use rudimentary models that may not accurately estimate earthquake-induced casualties. Even when models are suitable for predicting the total number of fatalities and critical injuries, they may fail to adequately differentiate between different levels of injury severity. This paper draws attention to the importance of extending the seismic casualty assessment method by broadening the perspective on injury severity. To this cause, …