Civil and Environmental Engineering Commons^™

Optimization Of Concrete Mixtures For Use In Structural Elements, Waleed Almutairi

Graduate Theses and Dissertations

Portland cement is an essential ingredient in concrete. The use of cement is to enhance the strength as well as other hardened properties of concrete mixtures. Determining the accurate amount of cement is important because the required strength may not be achieved if not enough cement is used. By contrast, when using too much cement, concrete cracking may occur that leads to reducing durability. Researchers at the University of Arkansas (UA) have shown that many bridge decks achieve their 28 day design strength of 4000 psi by 7 days of age. Bridge decks having high strength may experience cracking, which …

Behavior And Strength Of Rc Spandrel Members Under Unsymmetrical Bending And Torsion Including Cfrp Retrofitting, Muhammad Fahim

Civil & Environmental Engineering Theses & Dissertations

This dissertation presents the outcome of an experimental and theoretical investigation of the behavior and strength of reinforced concrete spandrel members both with and without carbon fiber reinforced polymer (CFRP) retrofitting. Both isolated spandrel members with L-shaped cross section as well as those integrated with reinforced concrete slabs are studied. A series of isolated spandrel members were tested under separate and combined actions of unsymmetrical bending and torsion. Six of these specimens were retrofitted externally with high-strength CFRP strips. Materially nonlinear analysis procedures are also formulated and programmed for the spandrel members with and without CFRP retrofitting. Furthermore, ultimate bending-torsion …

The Effect Of Biocomposite Material In A Composite Structure Under Compression Loading, Benjamin Andrew Sweeney

Master's Theses

While composite structures exhibit exceptional strength and weight saving possibilities for engineering applications, sometimes their overall cost and/or material performance can limit their usage when compared to conventional structural materials. Meanwhile ‘biocomposites’, composite structures consisting of natural fibers (i.e. bamboo fibers), display higher cost efficiency and unique structural benefits such as ‘sustainability’. This analysis will determine if the integration of these two different types of composites are beneficial to the overall structure. Specifically, the structure will consist of a one internal bamboo veneer biocomposite ply; and two external carbon fiber weave composite plies surrounding the bamboo biocomposite. To acquire results …

Self-Sensing Cementitious Materials, Alexander Nicholas Houk

Theses and Dissertations--Civil Engineering

The study of self-sensing cementitious materials is a constantly expanding topic of study in the materials and civil engineering fields and refers to the creation and utilization of cement-based materials (including cement paste, cement mortar, and concrete) that are capable of sensing (i.e. measuring) stress and strain states without the use of embedded or attached sensors. With the inclusion of electrically conductive fillers, cementitious materials can become truly self-sensing. Previous researchers have provided only qualitative studies of self-sensing material stress-electrical response. The overall goal of this research was to modify and apply previously developed predictive models on cylinder compression test …

Restrained Shrinkage Of Fly Ash Based Geopolymer Concrete And Analysis Of Long Term Shrinkage Prediction Models, Md R. Islam, Mahbub K. Ahmed, Hosney Ara Begum, Erez N. Allouche

Journal of the Arkansas Academy of Science

The research presented in this manuscript describes the procedure to quantify the restrained shrinkage of geopolymer concrete (GPC) using ring specimen. Massive concrete structures are susceptible to shrinkage and thermal cracking. This cracking can increase the concrete permeability and decrease the strength and design life. This test is comprised of evaluating geopolymer concrete of six different mix designs including different activator solution to fly ash ratio and subjected to both restrained and free shrinkage. Test results obtained from this experimental setup was plotted along with the available empirical equation to observe the shrinkage strain of GPC and a model was …

Compact Facility For Testing Steady And Transient Thermal Performance Of Building Walls, Aimee Byrne, Gerard Byrne, Anthony Robinson

Articles

Energy efficiency retrofit of buildings represents a key effort in reducing EU energy demand by 20% by 2020. However, predictions tend to overestimate savings by large percentages. The shortfall in savings can be attributed to incorrect predictive techniques, comfort takeback along with other behavioural and workmanship variables. Common predictive techniques related to heat loss tend to be based on the U-value of the building envelope. This paper presents the design of a more straightforward and compact version of the traditional Hot-Box apparatus (measures U-value) which instead determines the thermal resistance of samples of building envelope. U-value includes the need to …

Optimising The Performance Of Cement-Based Batteries, Aimee Byrne, Shane Barry, Niall Holmes Dr., Brian Norton

Articles

The development of a battery using different cement-based electrolytes to provide a low but potentially sustainable source of electricity is described. The current, voltage, and lifespan of batteries produced using different electrolyte additives, copper plate cathodes, and (usually) aluminium plate anodes were compared to identify the optimum design, components, and proportions to increase power output and longevity. Parameters examined include water/cement ratio, anode to cathode surface area ratio, electrode material, electrode spacing, and the effect of sand, aggregate, salts, carbon black, silica fume, and sodium silicate on the electrolyte. The results indicate that the greatest and longest lasting power can …

Rubber Additives To Concrete Specimens, Kendall J. Sweitzer, Mary Mccannon

Williams Honors College, Honors Research Projects

Rubber, as an additive to concrete, would hypothetically cause a concrete specimen to take on some mechanical characteristics of the rubber to a certain degree. In particular, the concrete’s durability should increase when exposed to fluctuating temperature conditions due to the rubber additive. This experiment sets out to test crumb rubber as a concrete additive, cured under various atmospheric conditions. The effects shall be measured via a simple concrete compression test.

Unfortunately, several errors took place during experimental process that led to inconclusive results. However, it can be reasonably considered from testing Matrix One that the addition of crumb rubber …

Influence Of Concrete Compressive Strength On Transfer And Development Lengths Of Prestressed Concrete, Alberto Teodoro Ramirez-Garcia

Graduate Theses and Dissertations

This research examines the relationship between concrete compressive strength and strand bond. The goal of this research was to develop an equation that relates strand bond to concrete compressive strength at strand release (approximately 1 day of age) and at 28 days of age, and those equations are presented in this investigation. Strand bond is assessed by measuring the transfer length and development length for prestressed beams cast in the laboratory. In the U.S., strand bond is predicted using transfer length and development length equations provided by the American Concrete Institute (ACI-318) Building Code and American Association of State and …

Thin Film Concrete Coatings, Bobby W. Meade, Danny Wells, Theodore Hopwood Ii, Sudhir Palle

Kentucky Transportation Center Research Report

KTC researchers obtained eight types of concrete coatings to assess their performance and resistance to chloride penetration. Researchers evaluated eight of the systems in the field and seven in the laboratory. In the field, coatings were applied to a bridge pier that had suffered degradation and chloride contamination. This site will undergo long term monitoring in order to thoroughly evaluate the coating systems. Adhesion of all products in both field and laboratory application was sufficient to provide a durable coating, and ranged from approximately 500 psi to 1,600 psi. Researchers also tested color and gloss changes, which are early indicators …

Failure Mechanism Of Woven Roving Fabric/Vinyl Ester Composites In Freeze–Thaw Saline Environment, Elias Anis Toubia, Sadra Emami, Donald A. Klosterman

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

This experimental study investigates the degradation mechanisms of a glass fiber-reinforced plastic material commonly used in civil engineering applications. A substantial reduction in tensile, shear, and compression properties was observed after 100 days of freeze–thaw cycling in saline environment (-20°C to 20°C). Non-destructive inspection techniques were progressively conducted on unexposed (ambient condition) and exposed (conditioned) specimens. The dynamic mechanical analysis showed permanent decrease in storage modulus that was attributed to physical degradation of the polymer and/or fiber–matrix interface. This indicated the formation of internal cracks inside the exposed glass fiber-reinforced plastic laminate. The 3D X-ray tomography identified preferred damage sites …

Numerical Modeling And Seismic Assessment Of Smart Isolation System For High-Speed Railway Rc Bridge Subjected To Near-Field Ground Motions, Lingkun Chen

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Buckling Analysis Of Laminated Composite Box Beams, Domagoj Lanc, Goran Turkalj, Josip Brnic

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Miss Lonesome: Old Boats Past Their Prime, Garth Woodruff

Faculty Publications

No abstract provided.

Progress Of Carbonation In Chloride Contaminated Concretes, Yaocheng Wang, P. A.M. Basheer, S. Nanukuttan, Y. Bai

International Conference on Durability of Concrete Structures

Concretes used in marine environment are generally under the cyclic effect of CO₂ and chloride ions (Cl^-). To date, the influence of carbonation on ingress of chloride ions in concretes has been widely studied; in comparison, study on the influence of Cl^- on the progress of carbonation is limited. During the study, concretes were exposed to independent and combined mechanisms of carbonation and chloride ingress regimes. Profiles of apparent pH and chloride concentration were used to indicate the progress of carbonation and ingress of Cl^- in concretes. From the apparent pH profile, a carbonation front …

Corrosion Of Steel In Concrete And Its Prevention In Aggressive Chloride-Bearing Environments, Luca Bertolini, Maddalena Carsana, Matteo Gastaldi, Federica Lollini, Elena Redaelli

International Conference on Durability of Concrete Structures

This keynote paper deals with the durability of reinforced concrete (RC) structures exposed to aggressive environments characterized by high concentration of chloride ions, namely, marine environments or the use of de-icing salts. The mechanism of chloride-induced corrosion of steel in concrete is introduced, and its influence on the service life of RC structures is analyzed. Factors affecting the time to corrosion initiation are described with regard to both concrete properties and environmental exposure conditions. Design approaches available for achieving durability targets associated with the design service life are analyzed, focusing on studies carried out by the authors in recent years …

Effect Of The Inherent Eccentricity In Single-Lap Direct-Shear Tests Of Pbo Frcm-Concrete Joints, Tommaso D'Antino, Lesley Sneed, Christian Carloni, Carlo Pellegrino

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Investigation of the bond between fiber reinforced composites and the substrates onto which they are applied is of critical importance to understand their failure mechanisms. The bond behavior can be studied using different experimental test set-ups; the most commonly used are the single-lap and double-lap direct-shear tests. Although single-lap shear tests are simpler to carry out than double-lap shear tests, the presence of an eccentricity between the pulling and restraining forces leads to a mixed mode fracture process at the interface, which may influence the results. This study investigates the eccentricity effect on the bond behavior of fiber reinforced cementitious …

A Concrete Water Pasteurization Device For Third World Countries, Andrea R. Murchie

Senior Honors Projects, 2010-2019

In the rural areas of South Africa, as well as many other developing countries, people cook food and sterilize their water by heating over open fires. Many times the fires are inside of homes, which more often than not are very small. Children will often be the ones to tend to the fire, out of necessity while parents and other family members are tending to other work and needs.

The purpose of my Senior Honors Project was to design a concrete vessel that can hold water and heat the water to pasteurization (149°F) when exposed to sunlight for an extended …

Measuring Relative Humidity In Concrete Pavements As A Method To Assess Asr Mitigation Measures, Remington G. Reed

Civil Engineering Undergraduate Honors Theses

Alkali-silica reaction (ASR) in concrete is partly facilitated by available moisture within the concrete. In order to better understand this facilitation and to develop processes for ASR mitigation methods, it is necessary to establish a means of monitoring internal relative humidity (RH) within the concrete. Current procedures for measuring RH are time consuming; requiring several hours of equilibration time and specific external conditions to yield accurate results. In order to better understand RH monitoring, laboratory tests were conducted using commercially available RH probes and different controlled environments. Probes were carefully monitored and calibrated in controlled environments, and laboratory tests on …

Optimizing Chemical & Rheological Properties Of Rejuvenated Bitumen, Dominic Nguyen, Hamzeh Haghshenas Fatmehsari, Santosh Kommidi, Yong-Rak Kim

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Bitumen has long been a material used in the construction of roadways, yet new pavement only consists of low fractions of recycled materials due to poor compatibility of aged bitumen and new materials. Thus, rejuvenators, chemical additives, have been used in an attempt to re-balance the chemical composition and restore the physical properties of aged bitumen back to its virgin state. A fundamental understanding of how one particular rejuvenator, soybean oil, revitalizes bitumen was investigated using a multi-scale approach.

Fourier-transform infrared spectroscopy (FTIR) was used to determine the changes in chemical properties of pure and rejuvenated virgin and aged samples. …

Post-Repair Seismic Assessment Of Rc Bridges Damaged With Fractured Column Bars - A Numerical Approach, Ruili He, Yang Yang, Lesley H. Sneed

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Seismic repair of reinforced concrete (RC) bridge columns has been studied extensively during the past several decades; however, few studies have been conducted on the influence of the column repair (member level) on the post-repair performance of bridge structures (system level). In a previous experimental study by the authors, a method was developed to rapidly repair severely damaged RC bridge columns to enable the quick reopening of the bridge to emergency traffic. Thus, a lower limit state was used for the repair design, so that the lateral strength and drift capacity of a repaired RC column with fractured longitudinal bars …

Bond–Slip Behavior Of Fiber-Reinforced Polymer/Concrete Interface In Single Shear Pull-Out And Beam Tests, Tayyebeh Mohammadi, Baolin Wan, Kent A. Harries

Civil and Environmental Engineering Faculty Research and Publications

It has been assumed that the fiber-reinforced polymer/concrete interface is subjected to in-plane shear condition when intermediate crack debonding failure occurs. Therefore, the single shear pull-out test results are often used to predict the intermediate crack debonding failure in beams. In this study, the behavior of fiber-reinforced polymer-strengthened concrete beams and single shear pull-out specimens were studied experimentally and numerically. The bond–slip behavior of the fiber-reinforced polymer/concrete interface was obtained by single shear pull-out and beam tests. In all beam specimens, a concrete wedge located at the edge of the notch detached with the fiber-reinforced polymer debonding failure. This phenomenon …

Daylighting And Thermo-Electrical Performance Of An Autonomous Suspended Particle Device Evacuated Glazing, Aritra Ghosh

Doctoral

Suspended particle device (SPD) glazing is an AC powered switchable glazing. PV powered SPD evacuated (vacuum) glazing was proposed with the potential of reducing the heating demand, cooling demand and artificial lighting demand of a building. To achieve an autonomous SPD vacuum glazing, semi empirical simulation and outdoor characterisation was explored in this thesis. Transmission of SPD glazing (area 0.058 m2) varied from 5% when opaque to 55% when transparent in the presence of 110 V, 0.07 W AC supply was characterised in outdoor test cell in Dublin. The SPD glazing has variable spectral transmission in the presence of variable …

Late Morning Concurrent Sessions: Innovations In Aviation Technologies: Presentation: Relative Material Loss: A Methodology For Assessing Island Airport Steel Marine Bulkheads, Robert Ernsting, Constantine M. Koursaris

Aviation / Aeronautics / Aerospace International Research Conference

A July 2015 report from the Airports Council International – North America (ACI-NA) states “U.S. airports are long overdue for [a] major structural improvement projects. Most U.S. airports are aging, … and because of budgetary restrictions, they’re not aging well.”(Garcia and Clampet, 2015). The average US age is 40 years old with the youngest (Denver International) recently turning 20 years old. As airports continue to age, airport commissioners will struggle to find creative ways to either fund airport replacements or extend the service life of existing airport facilities (commonly referred to as service life extension projects or SLEP). Due to …

State-Of-The-Art Review Of Cathodic Protection For Reinforced Concrete Structures, Aimee Byrne, Niall Holmes, Brian Norton

Articles

Cathodic protection (CP) limits the corrosion of a metal surface by making it the cathode of an electrochemical cell. This can be achieved either by using a more active sacrificial anode to create a driving current, or by using inert anodes and impressing a current onto the cathode surface using an external direct current (DC) source. Impressed current cathodic protection (ICCP) is preferred where widespread protection is required, particularly in reinforced concrete structures. ICCP needs a constant DC power supply that is usually provided through a grid connection or independent generators. This paper presents the currently available CP systems for …

Case Studies Of Cavity And External Wall Insulation Retrofitted Under The Irish Home Energy Saving Scheme: Technical Analysis And Occupant Perspectives, Aimee Byrne, Gerard Byrne, Garrett O'Donnell, Anthony Robinson

Articles

The residential sector represents 27% of primary energy consumption in Ireland. This paper examines the case study of the Irish government’s national grant scheme to encourage energy efficiency retrofit in private housing. That is the Home Energy Saving (HES) Scheme, later rebranded the Better Energy: Homes (BEH) Scheme. The methodology involved monitoring several homes immediately before and after retrofit alongside discussions with occupants. The examination focused on specific measures commonly introduced through the HES/BEH programme − cavity and external wall insulation. It has been found that a significant decrease in heat loss through the walls was measured in all cases. …

Evaluating A New Cem Iii/A Cement For Concretes Exposed To Harsh Acid Rich Environments, David Thompson, Niall Holmes, John Reddy

Conference papers

The Irish Annex to the European specification, performance, production and conformity of concrete, IS EN 206, recommends CEM III/B cement for acid rich environments containing between 66 to 80% GGBS. However, BS 8500, the UK annex to EN 206 and the British Research Establishment (BRE) Special Digest 1, recommends CEM III/A cement with a GGBS range of 36-65%. This project investigated the performance of a new CEM III/A cement produced by Ecocem Ireland in concretes exposed to such environments using an extensive suite of laboratory tests.

In Ireland, up to €5.8bn will be invested to provide fresh drinking water and …

Underwater Explosion Energy Dissipation Near Waterborne Infrastructure, Paul R. Smith

Theses and Dissertations--Civil Engineering

Underwater explosions pose a significant threat to waterborne infrastructure though destructive pressure waves that can travel significant distances through the water. However, the use of bubble screens can attenuate the peak pressure and energy flux created by explosions to safe levels. This study investigates the prediction of pressure wave characteristics based on accumulated data, the damage potential of underwater explosions based on applied loads and effective material strength, and the bubble screen parameters required to prevent damage. The results were compiled to form a procedure for the design and implementation of a bubble screen the protection of waterborne infrastructure.

Preliminary Investigation Into The Rate Of Carbonation Of Concrete Blocks Under Normal Production Yard Conditions, Aimee Byrne, Eanna Nolan

Conference papers

The release of CO2 from calcination during the manufacture of cement can be partially or fully offset by the CO2 it naturally absorbs during its lifetime. This paper reports results from a preliminary investigation into the rate of carbonation in concrete blocks stacked in a production yard over a period of 6 months. The blocks were stacked in a normal manner under natural exposure conditions. Carbonation progress was determined by splitting the blocks and spraying the freshly exposed surface with a phenolphthalein solution at intervals over the test period. It was found that the rate of the carbonation front progression …

An Overview Of The Development Of Cement-Based Batteries For The Cathodic Protection Of Embedded Steel In Concrete, Aimee Byrne, Niall Holmes, Brian Norton

Conference papers

This paper presents an overview of the cement-based batteries developed in DIT for use in the cathodic protection of embedded steel in reinforced concrete undergoing chloride-induced corrosion. Cathodic protection delivers an external current (approximately 20mA per m2 of embedded steel) which effectively polarises the internal current generated during corrosion. The batteries developed in DIT comprise of a cement-based electrolyte containing different additives including sand, aggregate, salts, carbon black and plasticiser with protruding anode and cathode metal plates. These batteries produced an initial electrical output of 1.5V and 23mA through a 10 resistor as measured using data acquisition units and a …