Civil and Environmental Engineering Commons^™

New Type Of Lightweight Aggregate For Use In Structural Concrete, Jamal Khatib, Ali Jahami, Oussama Baalbaki, Adel Elkordi

BAU Journal - Science and Technology

This research studied the utilization of municipal solid waste incineration bottom ash (MSWI-BA) in lightweight coarse aggregate (LWC) production. A special method was followed to prepare the new aggregate to fully replace the normal aggregates (NWA) in concrete. The mechanical properties such as compressive strength, tensile strength, and elasticity modulus were investigated for the LWC concrete. Then, two beams were prepared; one from LWC and the other from NWC. The structural performance of beams made up of lightweight aggregates compared to normal aggregates was investigated. The results showed that this type of aggregates led to a 20% reduction in concrete …

Effects Of Bonding Pressure And Lamina Thickness On Mechanical Properties Of Clt Composed Of Southern Yellow Pine, Cody S. Bates

Theses and Dissertations

This study produced cross-laminated timber panels at a range of four lamina thickness (5/8, 1, 1 1/8, and 1 1/4 inch) and three bonding pressures (50, 125, 200 psi), producing a total of 12 panels for mechanical testing. The goal of this study is to observe how the thickness and pressure trends affect the mechanical properties of CLT. Tests include flatwise bending, flatwise shear, internal-bond, and delamination. Results showed that bending MOE decreases as the panel thickness increases while bonding pressure had no significance. Bending MOR was less significant for the thickness and more significant for pressure compared to the …

Shear Strength Of Concrete Beams Made With Belitic Calcium Sulfoaluminate Cement, Caleb W. Chesnut

Graduate Theses and Dissertations

The need for a cleaner alternative to portland cement (PC) concrete has led to increasing interest in alternatives to PC. Structural properties of most of these alternative cements are still an open research topic. One promising alternative cement is belitic calcium sulfoaluminate (BCSA) cement. The study presented in this paper investigated the shear strength, long term compressive strength, and carbonation in BCSA cement and PC concrete beams. A total of twelve eight-foot long beams were made; eight BCSA cement concrete beams and four PC concrete beams to be tested at various ages depending on cement type. Two beams of each …

Development Of Lambda Factors For Masonry Design With Lightweight Grout, Rumi Shrestha

All Theses

Reduction in structural mass, improvement in thermal performance, and reduction in shrinkage cracking through internal curing are some of the reasons that lightweight (LW) aggregates have been used in structures and pavements for decades. However, lightweight grout is still not permitted for use in reinforced masonry construction by the TMS 402/602-16 code. In order to realize the benefits of lightweight grout in U.S. reinforced masonry construction, a codified procedure for its use is required which must be informed by experimental testing.

This research is a pilot project directed to characterize the performance of LW grout in comparison to normal weight …

Impact Of Exposure On Thin Epoxy Overlay Performance, Abul Fazal Mazumder

Dissertations

Thin epoxy overlays are used for improving the condition and extending the service life of bridge decks. The tensile bond pull-off strength, evaluated as per the ASTM C1583, is used as the performance indicator. A failure in the substrate with a tensile strength of 250 psi or greater is considered acceptable. However, the performance evaluated on in-service bridge decks shows inconsistent results. Laboratory studies by several researchers documented a distinct performance difference when the overlays are exposed to room temperatures in comparison to elevated temperatures. However, the most influential parameters such as concrete surface profile, thermal compatibility between overlay and …

Semi Real-Time Detection Of Subsurface Consolidation Defects During Concrete Curing Stage, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Subsurface consolidation defect is a common issue in concrete pavement construction, and the hidden defects often require costly repairs after project delivery. Therefore, being able to identify this type of defect during construction will enable contractor to conduct quick repairs to avoid costly post-construction rework. In this paper a semi real-time detection approach using infrared thermography is introduced. The developed approach utilizes the hydration heat during curing time to identify the subsurface voids based on the regional temperature contrast. Experimental studies were conducted using artificial void-defect in different sizes and depths. The thermographic analysis is employed to locate the void-defects …

Frequency Effect On Peak Pressure Coefficients Using The Narrowband Synthesis Random Flow Generator (Nsrfg) Method, Zayuris Del Carmen Atencio Mojica

Graduate Theses and Dissertations

The collapse of the Tacoma Narrows Bridge in Washington state in 1940 due to high wind forces gave structural engineers notice of the importance of understanding the behavior of wind forces on infrastructure. Wind forces play an important role in the design of buildings and other structures. ASCE 7-16 is the manual used for the design of these buildings and other structures throughout the country. These design criteria have been approved based on research projects involving experimental procedures. For the design of wind loads, ASCE 7-16 uses criteria based on wind tunnel (WT) tests. However, since the development of computing …

Assessment Of Carbon Dioxide Emission And Its Impact On High-Rise Mixed-Use Buildings In Egypt, Ahmed Salah Hamza

Theses and Dissertations

With Egypt's vision of 2030 focusing on sustainable development with a true emphasis on Carbon Dioxide (CO₂) emission reduction in the newly built cities and high-rise buildings, efforts are exerted on various levels towards accomplishing the vision’s goals. This is achieved through multiple tools and models associated with aiding the reduction of carbon emissions, yet not a clear one was introduced for the mixed-use buildings in Egypt.

Through this work, a significant gap was identified with respect to high-rise buildings carbon emission assessment in Egypt. This was a main driving force for this work in an attempt to …

Enhancement Of Asphalt Performance By Graphene-Based Bitumen Nanocomposites, Sara Moghtadernejad, Ehsan Barjasteh, Ren Nagata, Haia Malabeh

Mineta Transportation Institute

As the State of California continues to grow, demand for enhanced infrastructure such as roadways and highways escalates. In view of the current average highway lifespan of 15–20 years, the improvement of asphalt binders leads to material sustainability by decreasing required maintenance and increasing the lifespan of roadways. In the present investigation, enhancement of asphalt binder properties was achieved by different methods of mixing varying compositions of graphene nanoparticles with an SBS polymer and asphalt binder. Additionally, experimental evaluation and comparison of the rheological and mechanical properties of each specimen is presented. Graphene nanoparticles have attracted great curiosity in the …

Use Of Biomimicry Design Approach In Constructing Sustainable Resilient Structures (Case Study: Port Of Beirut), Farouk Bader, Marwan Halabi, Hiba Mohsen, Maged Youssef

BAU Journal - Creative Sustainable Development

Resiliency is not the same as sustainability, nor its substitute, but definitely the two concepts complement each other’s. Sustainability is the avoidance of depletion of natural resources to maintain ecological balance whereas resiliency is to recover, adapt and keep going in the face of setbacks. While designing with green approach is important but what will happen to leed points if the building becomes uninhabitable due to disasters, that’s where resiliency comes into play. The 2019 statistics showed that natural disasters accounted for 133 billion dollars losses and manmade ones accounted for other 7 billion in addition to 11,755 people worldwide …

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Damage Evolution And High-Rate Response Of High-Strength Concrete Under Triaxial Loading, Brett Williams

Mechanical Engineering Research Theses and Dissertations

The research presented in this study focuses on understanding fundamental mechanisms that drive material response under dynamic loading conditions. The objectives of the research were to: (1) to understand damage initiation and propagation in the bulk geomaterial under a variety of loading conditions and (2) to systematically investigate the strain rate effects on the triaxial compressive response of cementitious materials through the development of an innovative, first of its kind large-diameter (50 mm) triaxial Kolsky bar system.

The triaxial compressive response of high-strength concrete is needed to understand pressure-dependent material behavior, which is important for modeling extreme loading events. However, …

Comparing The Environmental Impacts Of Using Mass Timber And Structural Steel, Khang Hoang Nguyen, Steelee Knight Morgan

Construction Management

Although mass timber has seen a gradual rise in demand in the past, there has been a lack of extensive research on the environmental impacts of using mass timber as a primary structural framing material. This paper compares structural steel, and mass timber’s total embodied carbon emissions. Accurate estimates were made using plans and specs for different projects retrieved from semi-structured interviews. The estimates were input through the EC3 Calculator to provide extensive total carbon emissions measurements between each construction material. Using structural steel framing increased the project’s overall environmental impact by roughly 84% compared to using mass timber. The …

Initial Assessment Of Liquefied Scrap Tire Concrete, Abdulkareem Kuaryouti, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

A new approach to incorporate scrap tire material into concrete was investigated, where two reclaimed waste tire components, carbon black and fuel oil, were used to replace a portion of water. The effect of “liquid tire” content to water ratios from 5-40% on an otherwise typical concrete mix were assessed, where compressive and flexural strength, flexural toughness, modulus of elasticity, and several fresh concrete properties were determined. Results were compared to typically expected results of traditional shredded tire mixes with equivalent tire content. It was found that the liquid tire mixes experienced significantly less losses of compressive strength and workability …

Structural Identification And Damage Detection In Bridges Using Wave Method And Uniform Shear Beam Models: A Feasibility Study, Mehran Rahmani, Manan Naik

Mineta Transportation Institute

This report presents a wave method to be used for the structural identification and damage detection of structural components in bridges, e.g., bridge piers. This method has proven to be promising when applied to real structures and large amplitude responses in buildings (e.g., mid-rise and high-rise buildings). This study is the first application of the method to damaged bridge structures. The bridge identification was performed using wave propagation in a simple uniform shear beam model. The method identifies a wave velocity for the structure by fitting an equivalent uniform shear beam model to the impulse response functions of the recorded …

Balsa Wood Bridge, Andrew Harris

All Undergraduate Projects

Faculty at Central Washington University proposed a challenge to mechanical engineering students that could be accomplished in an in-home setting. The goal was to create a balsa wood bridge, weighing no more than 85 grams, that can support a load over an open span and raise above its resting position by means of a mechanical system. To produce a successful solution to the problem, a vertical lift bridge was created consisting of two lifting towers and a load bearing bridge. Using equations of static equilibrium and strength of materials, the required width for each member was determined. Project requirements were …

Optimisation Of Retrofit Wall Insulation: An Irish Case Study, Rakshit D. Muddu, D M. Gowda, Anthony James Robinson, Aimee Byrne

Articles

Ireland has one of the highest rates of emissions per capita in the world and its residential sector is responsible for approximately 10% of total national CO2 emissions. Therefore, reducing the CO2 emissions in this sector will play a decisive role in achieving EU targets of reducing emissions by 40% by 2030. To better inform decisions regarding retrofit of the existing building stock, this study proposes Optimum Insulation Thicknesses (OIT) for typical walls in 25 regions in Ireland. The calculation of OIT includes annual heat energy expenditure, CO2 emissions, and material payback period. The approach taken is based on Heating …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Incorporation Of Perlite And Recycled Aggregates For Internal Concrete Curing, Yosra El Maghraby, Mohamed Nagib Abou-Zeid Prof., Mohamed Abdel-Raouf Dr.

Civil Engineering

No abstract provided.

Potential Advantages Of Basalt Frp Bars Compared To Carbon Frp Bars & Conventional Steel, Yosra El Maghraby, Mohamed Nagib Abou-Zeid Prof., Ezzeldeen Yazeed El Sayed Ahmed Prof

Civil Engineering

No abstract provided.

Timber Bridge Pile Splicing With Fiber Reinforced Polymer Wraps, Drew L. Damich

Graduate Theses, Dissertations, and Problem Reports (ETD)

Timber pile repair using splicing is widely used but little research has been done to determine their strength capacity after repair using this method. Current timber pile splicing mechanisms utilize various steel or wooden components. Fiber Reinforced Polymer (FRP) wraps can be utilized as replacement to conventional materials in splicing of timber piles. This study evaluated the strength capacities of traditional splicing mechanisms in relation to FRP wrap splice mechanisms. Traditional splicing mechanisms consisted of flat steel plate, C-channel steel plate, and wooden plate splices. The FRP wrap splice consisted of unidirectional glass/epoxy composite with three layers of fabric as …

Laboratory Testing And Mechanistic Analysis Of Treated Subgrade Soils, Hari Kumar Reddy Yarrapureddi

Civil Engineering Theses

Calcium-based stabilizing agents such as cement and lime have been extensively used to improve the engineering properties of base and subgrade layers of pavement systems. Recently, polymers and chemical stabilizers have become popular due to cost efficiency, ease of application, and fast curing times. In this study, California Bearing Ratio (CBR) values of polymer and chemical treated soils were compared with the CBR values of soils treated with conventional stabilizers. Parametric sensitivity analyses was carried out on key parameters including the type of subgrade soil, stabilizing agent, stabilizing agent treatment levels, and moisture conditioning. Additionally, numerical analyses was performed to …

Bio-Binder—Innovative Asphalt Technology, Amir Tabakovic

Articles

The global road network spans 16.3 million km [1], of which 5 million km is in the EU. These road networks fulfil major economic and social goals by facilitating the movement of goods and people throughout the EU, and are therefore of the utmost importance to the economic and social life of the EU [2]. National governments invest heavily in their road networks, e.g., in 2014, EUR 53.33 billion was invested in the development and maintenance of the EU road network [3]. Each year, the world produces 1.6 trillion tonnes of asphalt [4], of which 218 million tonnes is produced …

An Investigation Into The Effects Of Fly Ash On Freeze-Thaw Durability Prediction, Yancy Schrader

Graduate Theses and Dissertations

Air is purposefully entrained into concrete primarily to improve resistance to freeze-thaw deterioration while saturated with water. Air entraining admixtures (AEAs) are chemical admixtures designed to entrain air into the concrete to provide adequate resistance to the effects of freezing and thawing. One of the challenges associated with air entrainment in concrete is the interaction of an AEA with supplementary cementitious materials present in the concrete, particularly fly ash. Fly ash is a by-product of the coal fired electrical generation industry, and often contains residual unburned carbon and other components that can increase the AEA demand of a particular concrete …

Effect Of Citric Acid On Slump, Compressive Strength, And Setting Time Of Belitic Calcium Sulfoaluminate Concrete, Israel Aguilar Rosero

Graduate Theses and Dissertations

Belitic calcium sulfoaluminate (BCSA) cement has well established advantages related to fast setting time, fast strength gain, long-term strengths, shrinkage, and sustainability. Due to its fast setting and hardening, this type of cement has historically been used to repair concrete structures, highways, and runways. This work provides much needed guidance on establishing mix design criteria for BCSA cement. Guidance is also given on the effects of set retarders on strength, slump, and setting times. Citric acid and a phosphonic acid-based admixture were tested as retarders for different concrete mixtures. Three studies were performed. In the slump study five different water …

Leveraging Biomimicry And Additive Manufacturing To Improve Load Transfer In Brittle Materials, Ana Paula Bernardo

Graduate Theses and Dissertations

With the emergence of Additive Manufacturing (i.e., 3D printing) in construction, new strategically designed shapes can be created to improve load transfer through structural members and foundations. Cross-sections can be optimized to carry load using less material, or even using weaker constituent materials, like soils, which are cheap and abundant. The goal of this research is to investigate the benefits of using cellular patterns which leverage biomimicry in civil engineering applications, since nature has perfectly engineered materials and patterns which carry loads with the least amount of material possible. Most of the periodic cellular work to date has focused on …

Application Of Percentage Within Limits Concepts On A Balanced Mix Design Of Asphalt Mixtures, Elvis Alexander Castillo Camarena

Graduate Theses and Dissertations

Many agencies have incorporated rutting, and more recently cracking, laboratory test requirements in the design process of asphalt mixtures. The objective of each additional specification is to produce a balance between the stability and durability of the final product. Although a performance-engineered mixture design (PEMD), denoted here as a balanced mix design (BMD), offers compelling benefits, there is concern regarding the compatibility of the BMD with current construction practices. The objective of this work is to correlate a BMD method with realistic binder content construction tolerances by applying the concepts of a percent-within-limits (PWL) approach to field QC/QA. First, Chapter …

Development Of Bragg Fiber Sensor For Corrosion Detection, Cai Hui Tan

Student Works (2020-2029)

Steel corrosion has posed one of the major structural defects in the civil society today. Conventional methods for corrosion monitoring involve high maintenance cost and destructive methods with low accuracy. Recently, Fiber Bragg gratings (FBG) sensor with its high sensitivity in measuring strain and temperature have been widely studied and used in structural health monitoring (SHM). A non-destructive corrosion detection approach based on FBG sensors was developed and tested to monitor corrosion in this research work. The principle of FBG sensing is based on Bragg wavelength shifts that from the corrosion process that induced strain on the FBG due to …

Engineering Properties And Microstructural Characteristics Of Cement And Geopolymer Based Mortars Using Nontraditional Supplementary Cementitious Materials, Mathialagan Sumesh

Student Works (2020-2029)

The concrete repair and rehabilitation industry grows rapidly due to deterioration, damage and defects in concrete structures. For various reasons, the concrete construction industry is not sustainable; because it consumes huge quantities of virgin materials, the usage of Portland cement as prime binder. The production of cement is a major contributor to greenhouse gas emissions. In addition, the high cost of commercial repair material. Therefore, it is necessary to develop cost-effective alternative repair materials for concrete repairs. There have been many standard repair materials available in the market, which are costly and not affordable to common people. However, research works …

Automatic Delamination Segmentation For Bridge Deck Based On Encoder-Decoder Deep Learning Through Uav-Based Thermography, Chongsheng Cheng, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Concrete deck delamination often demonstrates strong variations in size, shape, and temperature distribution under the influences of outdoor weather conditions. The strong variations create challenges for pure analytical solutions in infrared image segmentation of delaminated areas. The recently developed supervised deep learning approach demonstrated the potentials in achieving automatic segmentation of RGB images. However, its effectiveness in segmenting thermal images remains under-explored. The main challenge lies in the development of specific models and the generation of a large range of labeled infrared images for training. To address this challenge, a customized deep learning model based on encoder-decoder architecture is proposed …