Civil and Environmental Engineering Commons^™

Modeling Of Coupled-Tank System Using Fuzzy Takagi-Sugeno Model, Aries Subiantoro

Makara Journal of Technology

Modeling of Coupled-Tank System Using Fuzzy Takagi-Sugeno Model. This paper describes modeling of coupledtank system based on data measurement using fuzzy Takagi-Sugeno model. The fuzzy clustering method of Gustafson- Kessel algorithm is used to classify input-output data into several clusters based on distance similarity of a member of input-output data from center of cluster. The formed clusters are projected orthonormally into each linguistic variables of premise part to determine membership function of fuzzy Takagi-Sugeno model. By estimating data in each cluster, the consequent parameters of fuzzy Takagi-Sugeno model are calculated using weighted least-squares method. The resulted fuzzy Takagi-Sugeno model is …

Design Of Induction Motor Drive Without Velocity Sensor Using Current Vector Controller With Full And Reduced Observer Moving To Dq Axis, Ridwan Gunawan, Feri Yusivar, Wahidin Wahab, Zuhal A. Kadir

Makara Journal of Technology

Design of Induction Motor Drive Without Velocity Sensor Using Current Vector Controller with Full and Reduced Observer Moving to DQ Axis. The observer is used in estimation velocity sensor usually in α-β axis, therefore this situation will need an extra transformation when we want to add compensator because the flux model is in direct and quadrature-axis dq. Every used the transformation to make possible emerge an error. So in this simulation is used a method to estimate the velocity of induction motor drive with observer that is moved to dq-axis. The model of actual motor used is in alfa-beta axis, …

Hybrid Identification System With Arx And Fast Fourier Transform In Application Of A Quarter Of Vehicle Half Active Suspension, Noveri Lysbetti M, Antonius R.

Makara Journal of Technology

Hybrid Identification System with ARX and Fast Fourier Transform in Application of a Quarter of Vehicle Half Active Suspension. In a control system problem, identification system mechanism is a absolute thing, especially in adaptation controlling to disturbance changing. For that case, is needed an identification method which can identify the changing of disturbance in that system. The aim of this research is to give an alternative in system/plant identification which is a combination (hybrid) of ARX and Fast Fourier Transform. So, it is needed an algorithm design for identification process. In this case, the designed algorithm will be implemented in …

Ccfss Technical Bulletin Spring 2006, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Collapse Of The Quebec Bridge, 1907, Cynthia Pearson, Norbert Delatte

Civil and Environmental Engineering Faculty Publications

In the late 19th century, the transportation needs of Quebec led to proposals for bridging the St. Lawrence River. The Quebec Bridge was the longest cantilever structure attempted until that time. In its final design, the clear span was 548.6 m (1,800 ft) long. The bridge project was financially troubled from the beginning. This caused many setbacks in the design and construction. Construction finally began in October 1900. In August 1907, the bridge collapsed suddenly. Seventy five workers were killed in the accident, and there were only 11 survivors from the workers on the span. A distinguished panel was assembled …

Ccfss News Spring 2006, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Residential Hip Roof Framing Using Cold-Formed Steel Members, Luke Waldo, Sutton F. Stephens, Roger A. Laboube

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Galvanized Steel Framing For Residential Buildings, Nahb Research Center, Inc.

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Development Of Cost-Effective, Energy Efficient Steel Framing: Structural Performance Of Slit-Web Steel Wall Studs, Nahb Research Center

CCFSS Library (1939 - present)

No abstract provided.

Development Of Cost-Effective, Energy Efficient Steel Framing: Thermal Performance Of Slit-Web Steel Wall Studs, Nahb Research Center

CCFSS Library (1939 - present)

No abstract provided.

Study Of Same-Lane And Inter-Lane Gvw Correlation, Bernard Enright, Eugene J. O'Brien, Colin C. Caprani

Conference papers

The methodology used is to generate a number of years of simulated traffic and to use extreme value statistics to predict more accurately the characteristic loading for a given bridge. The parameters and probability distributions used in the Monte Carlo simulation must be based on observed sample traffic data. Some previous studies have made unsubstantiated assumptions regarding correlation between the Gross Vehicle Weights (GVW) of trucks in the same lane, or between trucks in adjacent, same-direction lanes. For this paper, an extensive database of Dutch Weigh-in-Motion data is analysed. Data are collected from two same-direction lanes and are time-stamped to …

The Girl Scout Climbing Wall Multidisciplinary Service-Learning Project, Margaret Pinnell, Corinne M. Daprano, Gabrielle Williamson

Mechanical and Aerospace Engineering Faculty Publications

The Girl Scout Wall (GS Wall) project was implemented in two classes at the University of Dayton (UD): a Mechanical and Aerospace Engineering (MAE) course, and a Health and Sports Science (HSS) course, and Sport Facility Management. The MAE course, Introduction to Materials, is a three-credit, third-year required course where students learn about the basic structure and properties of materials as well as the principles of material selection. The Sport Facility Management course is a three-semester hour, required HSS course where students are introduced to the processes of planning, constructing, equipping, maintaining, and managing sport facilities.

Synthesis Of Fuel Cell Membrane: Copolymerization Of Styrene On Etfe Film By Grafted Pre-Irradiation, Yohan Yohan, Rifai M. Nur, Lilik Hendrajaya, E. S. Siradj

Makara Journal of Technology

Synthesis of Fuel Cell Membrane: Copolymerization of Styrene on ETFE Film by Grafted pre-Irradiation. Preirradiation Grafting styrene monomer on ETFE film has been prepared. Research has been performed by γ-ray radiation at various total dose from 2.5 – 12.5 kGy and various dose rate from 1.3 – 1.9 kGy/hour. Irradiated copolymer is then grafted by styrene monomer in various solvent: ethanol, 2-propanol, and toluene, various concentration from 20 – 70% volume, various temperature from 50 – 90oC, and various grafting time from 2 – 12 hours. The results showed that percent of grafting is increase with increase of total dose …

Design Of Product Placement Layout In Retail Shop Using Market Basket Analysis, Isti Surjandari, Annury Citra Seruni

Makara Journal of Technology

Retailing is an industry with high level of competition. It is a customer-based industry which depends on how it could be aware of what the customers’ needs and requirements are. One technique most used in supermarkets is the mix merchandise. The purpose of this paper is to identify associated products, which then grouped in mix merchandise with the use of market basket analysis. This association between products then will be applied in the design layout of the product in the supermarket. The process of identifying the related products bought together in one transaction is done by using data mining technique. …

Production Hydrogen And Nanocarbon Via Methane Decomposition Using Ni-Based Catalysts. Effect Of Acidity And Catalyst Diameter, Widodo W. Purwanto, M. Nasikin, E. Saputra, L. Song

Makara Journal of Technology

Objectives of this research are mainly to study impacts of acidity strength (by varying amount of precipitant and loading Al-Si) and the effect of nickel particle size (by varying calcinations temperature) on decomposition reaction performances. In this research, high-nickel-loaded catalyst is prepared with two methods. Ni-Cu/Al catalysts were prepared with co-precipitation method. While the Ni-Cu/Al-Si catalyst were prepared by combined co-precipitation and sol-gel method. The direct cracking of methane was performed in 8mm quartz fixed bed reactor at atmospheric pressure and 500-700°C. The main results showed that the Al content of catalyst increases with the increasing amount of precipitant. The …

Design And Implementation Of 1-2 Ghz Stepped Frequency Gpr For Buried Metal Detection, Joko Suryana, Andriyan B. Suksmono, Tati R. Mengko

Makara Journal of Technology

Design and Implementation of 1-2 GHz Stepped Frequency GPR for Buried Metal Detection. In this paper, we describe the design and realization steps of 1 – 2 GHz SFGPR (Stepped Frequency Ground Penetrating Radar) transceiver for metal detection under the ground. Before using prototyped GPR for detecting the metal under the ground, several of calibration processes must be performed, namely phase calibration and monocycle pulse waveform calibration. After completing the calibrations, this prototyped GPR would be ready for detecting a hidden object such as a metal plate 5 cm under the ground in our small test range size 25 cm …

Simultaneous Treatment Of Organic (Phenol) And Heavy Metal (Cr6+ Or Pt4+) Wastes Over Tio2, Zno-Tio2 And Cds-Tio2 Photocatalysts, Slamet Slamet, R. Arbianti, Daryanto Daryanto

Makara Journal of Technology

Simultaneous Treatment of Organic (Phenol) and Heavy Metal (Cr6+ or Pt4+) Wastes over TiO2, ZnO-TiO2 and CdS-TiO2 Photocatalysts. Treatment of heavy metal (Cr6+ and Pt4+) and organic (phenol) wastes has been studied using the relatively new method, i.e. simultaneous photocatalytic process over TiO2 photocatalysts in the batch photoreactor. Following the photocatalytic reduction of the heavy metal wastes, recovery of Cr and Pt was carried out by precipitation and leaching method, respectively. The experimental results show that in the simultaneous photocatalytic system, there is a synergism effect between the photocatalytic reduction of heavy metal waste (Cr6+ or Pt4+) and the oxidation …

Design Of Generating Dual Frequency Operation For Triangular Microstrip Antenna Using Electromagnetic Coupling, Indra Surjati, Eko Tjipto Rahardjo, Djoko Hartanto

Makara Journal of Technology

Design of Generating Dual Frequency Operation for Triangular Microstrip Antenna Using Electromagnetic Coupling. A new design is proposed in this paper by applying a pair of slits using a microstrip feed line. Therefore the microstrip line feeding system is electromagnetically coupled to the patch. The antenna works at two different frequencies in the range from 2 GHz to 4 GHz (S band frequency). The results of the simulation shows that the dual frequency operation can be created when the slit width is 1 mm and the height of the slits ranges from 10 mm to 14 mm with inter slit …

Development Of Low Frequency Vibration Method Of Direct-Write Deposition Relevant To Layer Manufacturing Application, Susilo Adi Widyanto, Alva Edy Tontowi, Jamasri Jamasri, Heru Santosa Budi Rochardjo

Makara Journal of Technology

The research of deposition process is the first step in development process of multi materials selective laser sintering. The deposition process enables to settle multi materials powder in horizontal formation on one layer. In this research we use low frequency (70 - 200Hz) to vibrate a hopper nozzle in which powder is settled. The research method consists of two steps, the first step is to determine flow-ability parameters and the second is to join flow ability parameter with other parameters such that the line width can be controlled. The results show that the line width depends on uniformity of particle …

Load And Resistance Factor Calibration For Wood Bridges, Andrzej S. Nowak, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

The paper presents the calibration procedure and background data for the development of design code provisions for wood bridges. The structural types considered include sawn lumber stringers, glued-laminated girders, and various wood deck types. Load and resistance parameters are treated as random variables, and therefore, the structural performance is measured in terms of the reliability index. The statistical parameters of dead load and live (traffic) load, are based on the results of previous studies. Material resistance is taken from the available test data, which includes consideration of the post-elastic response. The resistance of components and structural systems is based on …

Strength Of Cfs Floor Assemblies With Clip Angle Bearing Stiffeners, S. R. Fox

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Experimental Evaluation Of The Strength And Behaviour Of 16- And 18-Gauge Cold Formed Steel Top Track Systems, J. L. Dawe

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Cold-Formed Steel Walls With Fiberboard Sheathing - Shear Wall Testing, Nahb Research Center, Inc.

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Ccfss Technical Bulletin Fall 2005, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Ccfss News Fall 2005, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Key Seismic Design Parameters: Steel And Wood Light-Frame Shear Walls, Coheen & Associates Structural Engineering

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Evaluation Of Accuracy And Efficiency Of Some Simulation And Sampling Methods In Structural Reliability Analysis, Christopher D. Eamon, Michel D. Thompson, Zhenyu Liu

Civil and Environmental Engineering Faculty Research Publications

Numerous simulation and sampling methods can be used to estimate reliability index or failure probability. Some point sampling methods require only a fraction of the computational effort of direct simulation methods. For many of these methods, however, it is not clear what trade-offs in terms of accuracy, precision, and computational effort can be expected, nor for which types of functions they are most suited. This study uses nine procedures to estimate failure probability and reliability index of approximately 200 limit state functions with characteristics common in structural reliability problems. The effects of function linearity, type of random variable distribution, variance, …

Failure Investigation Of The Steel Strut Of Paseo Suspension Bridge, Genda Chen, Chris Courtright, Lokeswarappa R. Dharani, B. Xu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A vertical strut of the 1232-foot long, self-anchored Paseo Suspension Bridge fractured when the temperature hit at a record low of 9°F below zero. During inspection the following day, it was found that its lower pin was frozen and did not allow for free movement of the superstructure. The objective of this study is to pinpoint one of the four reasons for this incidence or their combination: overstressing, thermal contraction, fatigue, and reduction in fracture toughness at low temperatures. To achieve this objective, material property and fatigue testing was performed on samples of strut material while the bridge and strut …

Aisi Standard For Cold-Formed Steel Framing – Truss Design, 2004 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing Standards. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed steel framing design and installation. The Committee acknowledges and is grateful for the contributions of the numerous researchers, engineers, and others who have contributed to the body of knowledge on the subject. Specific references are included in the Commentary. With anticipated improvements in understanding of the behavior of cold-formed steel framing and the continuing development of new technology, this material may eventually become dated. It is …

Standard For Cold-Formed Steel Framing - Truss Design, 2004 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The material contained herein has been developed by the American Iron and Steel Institute Committee on Framing Standards. The Committee has made a diligent effort to present accurate, reliable, and useful information on cold-formed steel framing design and installation. The Committee acknowledges and is grateful for the contributions of the numerous researchers, engineers, and others who have contributed to the body of knowledge on the subject. Specific references are included in the Commentary.

With anticipated improvements in understanding of the behavior of cold-formed steel framing and the continuing development of new technology, this material may eventually become dated. It is …