Civil and Environmental Engineering Commons^™

Research Agenda For Transportation Infrastructure Preservation And Renewal: Conference Report, Joseph L. Schofer, Leonard Evans, Michael P. Freeman, Larry L. Galehouse, Samer Madanat, Ali Maher, Sue Mcneil, John J. Myers, Robert L. Peskin, Butch Wlaschin

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.

An Investigation Of The Influence Of Diaphragm Flexibility On Building Design Through A Comparison Of Forced Vibration Testing And Computational Analysis, Blake Alan Roskelley

Master's Theses

An assessment of the validity of idealizing a concrete diaphragm as rigid was performed through the modal analysis of three existing buildings. Modal analysis was performed both by physical experimentation and computational analysis. Experimental determination of the mode shapes shows that two of the three buildings’ diaphragms exhibited flexible behavior. The experimental results were compared to computational analysis results and were shown to be similar, confirming that that the two building diaphragms are not rigid. As a standard, diaphragms with aspect ratios less than three are permitted to be idealized as rigid per ASCE 7-05. To determine the effect of …

Reliability Estimation Of Complex Numerical Problems Using Modified Conditional Expectation Method, Christopher D. Eamon, Bulakorn Charumas

Civil and Environmental Engineering Faculty Research Publications

A simulation-based structural reliability analysis method is presented. It is intended as an alternate approach to estimate reliability for problems for which most-probable point of failure methods fail and when computational resources are limited. The proposed method combines conditional expectation and estimating the PDF or CDF of a selected portion of the limit state. In the proposed approach, complex limit state functions are simplified to two random variable problems. The success of the simplification depends on the quality of the CDF estimate. Results indicate that the method may provide accurate and efficient solutions for some difficult reliability problems.

Plain And Steel-Reinforced Concrete Shear Walls With And Without Cfrp Retrofitting, Ali Mohammed Salih Al Aloosi

Civil & Environmental Engineering Theses & Dissertations

This thesis presents the outcome- of a study of the behavior and strength of plain and steel-reinforced concrete shear walls with and without a window opening and Carbon Fiber-Reinforced Polymer (CFRP) retrofitting. A total of seven tests were conducted using six different shear walls. Each wall was subjected to a gradually increasing static load at one of it's top corners until the maximum load was reached. The load-deflection relations and the walls' failure patterns were observed and recorded. It was found that the window opening in the plain concrete wall reduced the wall load capacity by 18 percent. For the …

Performance-Based Analysis Of Steel Buildings: Special Concentric Braced Frame, Scott Michael Adams

Master's Theses

The performance-based analysis methods and evaluation criteria in ASCE 41-06 were used to evaluate a special concentric braced frame building based on the design standards in ASCE 7-05. A rectangular, six-story office building was evaluated using linear static, linear dynamic, nonlinear static, and nonlinear dynamic procedures. The results showed that the linear procedures underestimated damage compared to the nonlinear procedures, with the building performing to Life Safety for the linear procedures, and the nonlinear procedures indicating component damage beyond the intended Life Safety limit for the 2/3 maximum considered earthquake (MCE) hazard. This trend continued to the maximum considered earthquake …

Coated Steel Rebar For Enhanced Concrete-Steel Bond Strength And Corrosion Resistance, Genda Chen, Jeffery S. Volz, Richard K. Brow, Dongming Yan, Signo Tadeu Dos Reis, Chenglin Wu, Fujian Tang, Charles R. Werner, Xing Tao

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This report summarizes the findings and recommendations on the use of enamel coating in reinforced concrete structures both for bond strength and corrosion resistance of steel rebar. Extensive laboratory tests were conducted to characterize the properties of one- and two-layer enamel coatings. Pseudostatic tests were performed with pullout, beam and column specimens to characterize mechanical properties and develop design equations for the development length of steel rebar in lap splice and anchorage areas. The splice length equation was validated with the testing of large-scale columns under cyclic loading. For corrosion properties, ponding, salt spray, accelerated corrosion, potentiodynamic and electrochemical impedance …

Experimental Investigation Of Folded Plate Girders And Slab Joints Used In Modular Construction, Kyle A. Burner

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The folded plate girder, a newly proposed bridge girder, is investigated through this thesis. The folded plate girder is cold bent out of a single sheet of steel. The cold bending eliminates the costly and inconsistent shop welds found in traditional girders. The folded plate girder is meant for application in short span bridges. The girder was subjected to an equivalent 75 year lifetime loading to investigate the fatigue performance.

The rebar detail used in the closure region between adjacent slabs has been investigated in the past by the NCHRP 12-68 project. This thesis will proposes a hooked rebar detail …

Constructability Testing Of Folded Plate Girders, Luke A. Glaser

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

A new steel girder bridge system was developed at the University of Nebraska. The innovative girder design is a box girder folded from a single steel plate that has a trapezoid shape with an opening on the bottom. The girder has application in short span bridges and accelerated construction situations. The structural performance of the girder requires investigation in all stages of a bridge’s lifecycle. This thesis contains descriptions and results from the first two tests from a series of tests developed to evaluate this new girder shape. The objective of these two tests was to investigate the constructability of …

Supplement No. 2 To The North American Specification For The Design Of Cold-Formed Steel Structural Members, 2007 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Intricacies Of Professional Certifications For Quality Management (Qm), Edmund R. Martelli

Masters Theses & Specialist Projects

The modern manufacturing marketplace is extremely complex and constantly changing. Career professionals often seek job placement, career advancement, and continuing education through professional certifications. Professional certifications in the United States (U.S.) have been evolving since 1911. In the 1950s, engineering groups established professional certifications and licenses. In the 1980s, administration of accreditation of certification programs proliferated, and by the 1990s, many government and professional organizations sought to standardize procedures for the industry. Currently, professional certifications are available for virtually every profession and issued by multitudes of organizations.

Quality management (QM) encompasses an extensive combination ofprofessional abilities. Providers of professional certifications …

Modelling And Verification Of Response Of Rc Slabs Strengthened In Flexure With Mechanically Fastened Frp Laminates, Annalisa Napoli, Fabio Matta, Enzo Martinelli, Antonio Nanni, Roberto Realfonzo

Faculty Publications

Mechanically fastened fibre-reinforced polymer laminate systems are emerging as a promising means for the repair and strengthening of reinforced concrete members. This technology entails the use of pultruded carbon- and glass- vinyl ester fibre-reinforced polymer laminates with enhanced longitudinal bearing strength that are connected to the concrete substrate by means of steel anchors. Attractive applications are those for emergency repairs where constructability and speed of installation are critical requirements. In this paper, an experimental investigation is first presented that included laboratory testing of scaled reinforced concrete slabs strengthened with four different combinations of laminate lengths and fastener layouts to study …

Failure Literacy In Structural Engineering, Norbert J. Delatte

Civil and Environmental Engineering Faculty Publications

The history of the development of practice in many engineering disciplines is, in large part, the story of failures, both imminent and actual, and of the changes to designs, standards and procedures made as the result of timely interventions or forensic analyses. All engineers, and more particularly structural engineers, should be failure literate. Failure literacy means knowing about the critical historical failure cases that have shaped the profession: not merely the surface technical details, but the environment, the communications difficulties and the procedural issues. In the US, an intensive effort has been under way for nearly a decade to promote …

The Effect Of Service Installations On Structural Integrity Of Slabs In Buildings, Ladislaus Lwambuka

Tanzania Journal of Engineering and Technology (TJET)

In building construction industry service installations, usually housed in conduit pipes, are commonly mounted inside reinforced concrete structural elements. This practice is adopted to attain aesthetical outlook at both interior and exterior surfaces of the buildings. Depending on the extent of service installations, the cross sectional area of the load bearing structural member is substantially reduced. However, the current structural design guidelines have no provision to accommodate the extent to which the existence of conduit pipes impairs the load bearing capacity of the structural element though reduced cross sectional area. This study has attempted to address this gap in structural …

Comparison Of The Properties Of Portland Cement And Portland-Limestone Cement, Alex Lyatonga Mrema

Tanzania Journal of Engineering and Technology (TJET)

A study was made in a cement factory in Dar es Salaam, Tanzania, where Ordinary Portland Cement (CEM I 42.5N) and Portland-limestone cement (PLC) which has the brand name Twiga Cement Extra (CEM II/A-L/32.5R) are produced and conforming to the Tanzania Standard TZS 727 (Part1): 2002, which is equivalent to EN 197 published by the committee for European normalization (CEN). A comparison was made between the two types of cements in terms of physical, chemical and mechanical properties. It was found out that they all complied with the standards, that there was no significant difference in their setting times and …

Simplified Procedures For Seismic Analysis And Design Of Piers And Wharves In Marine Oil And Lng Terminals, Rakesh K. Goel

Civil and Environmental Engineering

No abstract provided.

Scale Model Shake Table Testing Of Underground Structures In Soft Clay, Victor A. Crosariol

Master's Theses

Underground structures perform an important role in transportation systems in many seismically active regions around the world, but empirical data regarding the seismic behavior of these structures is limited. This research works towards filling that empirical gap through the use of scale model shake table testing. Underground seismic soil-structure interaction (USSSI) effects were investigated for a stiff rectangular tunnel cross-section embedded within soft clay. San Francisco Young Bay Mud was used as a prototype soil for developing a scale model soil mixture consisting of kaolinite, bentonite, class C fly ash, and water. A single cell Bay Area Rapid Transit (BART) …

Report On Laboratory Testing Of Anchor Bolts Connecting Cold-Formed Steel Track To Concrete With Minimum Edge Distances, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Siding Attachment To Cold-Formed Steel Walls Through Varying Layers Of Foam Insulation, Newport Ventures, Inc., Applied Residential Engineering Services

CCFSS Library (1939 - present)

When insulating an exterior wall, more and more codes are requiring continuous insulation on the exterior of the studs to reduce the effect of thermal bridging. As energy codes continue to become more stringent, the thickness of the continuous installation has increased. Although wood and steel are both impacted, the requirements generally are higher for steel framing.

A significant implementation challenge caused by increasingly higher levels of continuous insulation is the lack of specifications for the type of fastener and siding installation details that should be used when installing thicker levels of insulation. Thus, the engineer, architect, builder, and contractor …

Achieving The Vision Through High Ethical Standards, Sarah E. Bertke

Ohio Valley Regional Student Conference

No abstract provided.

Input-Output Analysis Of Irish Construction Sector Greenhouse Gas Emissions, Adolf Acquaye, Aidan Duffy

Articles

Ireland is committed to limiting its greenhouse gas (GHG) emissions to 113% of 1990 levels over the period 2008-12 and to 84% of 2005 levels by 2020 under the Kyoto Agreement and the EU’s ’20 20’ by 2020 respectively. National policies have targeted many industry sectors but have failed to directly tackle GHG emissions associated with construction activity. This paper estimates energy and GHG emissions intensities of the Irish construction sector and subsectors and estimates its contribution to Irish national emissions. This information is used to identify and assess the impacts of policy measures which would result in a reduction …

A Simple Technique For Surface Area Determination Through Supercritical Co2 Adsorption, Mahmud Sudibandriyo

Makara Journal of Technology

The measurement of specific surface area of porous materials has long been important in physical sciences and is currently growing in importance in applied and environmental science. Numerous systems have been developed for surface area measurement by gas adsorption. Commercial systems are available which can measure a wide range of absolute surface area with relative ease. However, their cost is often prohibitive. In this study, an inexpensive apparatus for surface area measurement has been set up to be used for measuring supercritical adsorption of CO2. The Ono-Kondo Lattice model was used to represent the adsorption isotherm and to determine the …

Fishing Catch And Catch Rate Assesment Of Mini Trawl, Trapnet And Setnet Fisheries, Muhammad Firdaus

Makara Journal of Technology

Fishing Catch and Catch Rate Assesment of Mini Trawl, Trapnet and Setnet Fisheries. This paper is aimed at assessing fishing catch and catch rate of the dragged gear on shrimp, trapnet, and setnet fisheries in Tarakan. The catch and effort data (number and species) and the fishing time of captured units were used in this qualitative analysis of fishing catch and catch rate to describe catch composition and catch rate from three catch fishery units in Tarakan. The result of the research shows that in the catching operation the dragged gear on shrimp has two main catch targets, which are …

Ontology-Based Automatic Classification For News Articles In Indonesian Language, Prajna Wira Basnur, Dana Indra Sensuse

Makara Journal of Technology

Ontology-Based Automatic Classification for News Articles in Indonesian Language. Searching specific information will be difficult if relying only on query. Choosing less specific queries will result in a lot of irrelevant information fetched by the system. One of the most successful ways to overcome this problem is to perform document classification based on the topic. There are many methods that can be used to conduct such a classification, such as using statistical and machine learning approaches. However, those document classification methods require training the data or learning the documents. In this study, the authors attempted to classify documents using a …

Particle Filter With Binary Gaussian Weighting And Support Vector Machine For Human Pose Interpretation, Indah Agustien, Muhammad Rahmat Widyanto, Sukmawati Nur Endah, Tarzan Basaruddin

Makara Journal of Technology

This paper proposes human pose interpretation using particle filter (PF) with Binary Gaussian Weighting and support vector machine (SVM). In the proposed system, particle filter is used to track a human object, then this human object is skeletonized using thinning algorithm and classified using SVM. The classification is to identify human pose, whether it is normal or abnormal behavior. Here particle filter is modified through weight calculation using Gaussian distribution to reduce the computational time. The modified particle filter consists of four main phases. First, particles are generated to predict target’s location. Second, the weight of certain particles is calculated …

Maintenance Activity Planning By Reability Centered Maintenance Ii Method, Rachmad Hidayat, Nachnul Ansori, Ali Imron

Makara Journal of Technology

Maintenance Activity Planning by Reability Centered Maintenance II Method. This research discusses maintenance activity planning using the RCM II method to evaluate failure function risk on compresor screw. The calculation of maintenance time is performed by considering maintenance and repair costs. The risk evaluation result with RPN shows that the critical component that needs to get the main priority in applying maintenance on compresor screw is function disorder on timeworn piston and on the broken outgoing air sponge’s filter that receives RPN 45. The optimum maintenance time calculation is applied on components that undergo scheduled restoration and scheduled discard task …

Software Design Of Mobile Antenna For Auto Satellite Tracking Using Modem Correction And Elevation Azimuth Method, Djamhari Sirat, Muhamad Asvial, Arman Djohan Diponegoro, Himawan Sidharta

Makara Journal of Technology

Software Design of Mobile Antenna for Auto Satellite Tracking Using Modem Correction and Elevation Azimuth Method. Pointing accuracy is important in satellite communication. Because the satellite’s distance to the surface of the earth's satellite is so huge, 1 degree of pointing error will make the antenna unable to send data to satellites. To overcome this, the auto-tracking satellite controller is made. This system uses a microcontroller as the controller, with the GPS as the location indicator of the antenna, a digital compass as the beginning of antenna pointing direction, a rotary encoder as azimuth and elevation censor, and a modem …

Petroleum Degradation In Soil By Thermophilic Bacteria With Biopile Reactor, Astri Nugroho, Edison Effendi, Yulius Karonta

Makara Journal of Technology

Crude oil degradation has been carried out using biopile reactor in total petroleum hydrocarbon (TPH) concentration of 5%, 10% and 15%. The thermophilic microorganisms used from isolation result and identification are Aeromonas salmonicida, Bacillus pantothenticus, and Stenotrophomonas maltophilia. The biodegradation of biopile reactor is done by various concentrations of TPH, total plate count (TPC), and volatile suspended solid (VSS) per day for 30 days. The biodegradation of kinetic parameter calculated consists of μ, μm, Y, Yt, Yobs, Kd, Ks from TPH concentration decision, and TPC and VSS in every microorganism with t (observation time) of 0 hour to 168 hours. …

Ergonomic Analysis Of Ui’S Bicyclesusing Posture Evaluation Index (Pei) Method In Virtual Environment, Erlinda Muslim, Boy Nurtjahyo, Zulkarnain Zulkarnain, Liza Afrinotha

Makara Journal of Technology

Ergonomic Analysis of UI’s Bicycles Using Posture Evaluation Index (PEI) Method in Virtual Environment. This research was conducted to study the ergonomic aspect of University of Indonesia’s bicycles in virtual environment. Software Jack 6.0 was used to analyze it. PEI was used as an approach that integrated the results of three methods: lower back analysis (LBA), ovako working posture analysis (OWAS), and rapid upper limb assessment (RULA). The research objective is to evaluate the existing design of University of Indonesia’s bicycles and to determine the most ergonomic redesign which concerns handlebar height and saddle height modification. The result showed that …

Cold-Formed Steel Bolted Connections Using Oversized And Slotted Holes Without Washers, Phase 2, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

North American Standard For Cold-Formed Steel Framing -- Lateral Design, 2007 Edition With Supplement No 1. October 2009 (Reaffirmed 2012), American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.