Civil and Environmental Engineering Commons^™

Temperature And Strain Measurements With Fiber Optic Sensors For Steel Beams Subjected To Fire, Yi Bao, Yizheng Chen, Matthew S. Hoehler, Christopher M. Smith, Matthew F. Bundy, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents measurements of high temperatures using a Brillouin scattering based fiber optic sensor and large strains using an extrinsic Fabry-Perot interferometric sensor for assessing the thermo-mechanical behaviors of simply supported steel beams subjected to combined thermal and mechanical loading. The distributed fiber optic sensor captures detailed, non- uniform temperature distributions that are compared with thermocouple measurements resulting in an average relative difference of less than 5 % at 95 % confidence level. The extrinsic Fabry- Perot interferometric sensor captures large strains at temperatures above 1000 C. The strain results measured from the distributed fiber optic sensors and extrinsic …

The Design And Construction Of A Rear Bumper With Incorporated Spare Tire Rack, Alan C. Isaacson

BioResource and Agricultural Engineering

This senior project outlines the design and construction of a rear bumper with incorporated spare tire and equipment rack for a 1946 Willys CJ2A Jeep. The spare tire rack is capable of swinging out away from the vehicle to allow for the use of the vehicle’s tailgate. The bumper was designed for strength, functionality and aesthetic qualities alike. Additionally, the bumper design considered all vehicle codes and regulations.

Structural Calculations For Nepal Vocational Learning Center, Nicholas Petrarca

Architectural Engineering

This project goal is to build a Leadership Vocational School for youth, women, differently abled, and local leaders of rural and Kathmandu Nepal. The client for this project is an organization called Sakcham Rural Nepal and they partnered with a humanitarian organization called Journeyman International to find Architecture and Architectural Engineering students to design a safe, attractive and functional building to fit their needs.

Evaluation Of The Use Of Painted And Unpainted Weathering Steel On Bridges, Theodore Hopwood Ii, Sudhir Palle, Bobby W. Meade, Rick Younce

Kentucky Transportation Center Research Report

KTC researchers studied the use of unpainted weathering steel on bridges, using findings of inspections performed on Kentucky Transportation Cabinet (KYTC) bridges constructed with both painted and unpainted weathering steel as well as laboratory testing. Laboratory tests were conducted on test panels of conventional and weathering grades of steel to determine the performance of barrier and zinc-based coatings over abrasive-blasted substrates of those steel types in both the new and corroded conditions. The report provides the following recommendations for the use of painted and unpainted weathering steel on Kentucky bridges based upon both the field and laboratory findings:

• KYTC should …

Broad Street Apartments, Carla Alejandra Simental, Viviana C. Sanchez

Architectural Engineering

No abstract provided.

Retrofitting Adobe Buildings, Ashley V. Gaur, Jessica E. Ellis

Architectural Engineering

No abstract provided.

Experimental Building Demonstration Model With Viscous Fluid Dampers, Blake Thomas Reeve, Brianna Jean Kufa, Aden Malek Stepanians, Sophie Carmion Ratkovich

Architectural Engineering

The Architectural Engineering major places a heavy emphasis on structural dynamics and the role of wind and seismic loading in building analysis and design. Buildings of high importance that are critical to community function, such as hospitals, often utilize supplemental damping devices like supplemental viscous fluid dampers or base isolators to reduce the overall demands on the structural system. The design and analysis of these dampers are typically not taught at the undergraduate level, and is frequently performed by mechanical engineers, in lieu of structural engineers.

To better understand and research building behavior with supplemental damping devices, our multi-disciplinary team …

Development Of A Transition Between An Energy-Absorbing Concrete Barrier And A Rigid Concrete Buttress, Tyler Schmidt

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

From 2010 to 2015, MwRSF researchers developed the RESTORE barrier, which is a restorable MASH TL-4 median barrier with a steel and concrete rail supported by elastomer posts and steel skids. The research effort reported herein describes the initial development of a transition from the RESTORE barrier to a rigid TL-4 concrete buttress.

The previously-developed RESTORE barrier LS-DYNA model was validated against three full-scale vehicle crash tests. Several design concepts were generated through a series of brainstorming efforts. The primary transition concept consisted of a pin and loop connection between the RESTORE barrier and rigid concrete buttress, which was designed …

Seismic Design Of A Prestressed Concrete Bridge, Alperen Ozel

LSU New Orleans Theses and Dissertations

Latest advancements in software have become an indispensable tool in structural analysis. The main goal of this thesis is to examine dynamic responses of bridges in seismic activity with the help of such tool as CSi Bridge. Therefore, throughout this study, a prestressed concrete bridge model will be thoroughly designed. In the first section, the required materials and structural components will be introduced. The following section will cover calculations required for modeling. The actual modeling of the structure will be carried out in Section 3. In Section 4, the set of required analysis for seismic design such as modal, pushover …

Effect Of The Inherent Eccentricity In Single-Lap Direct-Shear Tests Of Pbo Frcm-Concrete Joints, Tommaso D'Antino, Lesley Sneed, Christian Carloni, Carlo Pellegrino

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Investigation of the bond between fiber reinforced composites and the substrates onto which they are applied is of critical importance to understand their failure mechanisms. The bond behavior can be studied using different experimental test set-ups; the most commonly used are the single-lap and double-lap direct-shear tests. Although single-lap shear tests are simpler to carry out than double-lap shear tests, the presence of an eccentricity between the pulling and restraining forces leads to a mixed mode fracture process at the interface, which may influence the results. This study investigates the eccentricity effect on the bond behavior of fiber reinforced cementitious …

Shear Behavior Of High-Strength Self-Consolidating Concrete In Nebraska University Bridge Girders, Alex Griffin, John J. Myers

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Current reinforced and prestressed concrete design equations were developed for conventional concrete elements. Self-consolidating concrete (SCC) typically contains a lower coarse aggregate content and size than conventional concrete, which potentially hinders the aggregate interlock contribution to a concrete's shear strength. Thus, shear design equations must be verified with SCC mixtures. Two full-scale precast, prestressed concrete Nebraska University girders were tested to assess the shear behavior of high-strength SCC. Both girders were designed to permit two tests on each girder, both with and without shear reinforcement. Ultimate shear loads and crack patterns were documented and compared with code estimates, finite element …

Design Of A Folding V-Scraper With Roller For Orchard Applications, Chase Ulrich

BioResource and Agricultural Engineering

This senior project discusses the design of a folding 15 ft. wide leveler for orchard use. This design utilized a category 2 three-point hitch to connect the implement to a tractor. The folding mechanism uses the tractors hydraulic system to actuate the folding movement using hydraulic cylinders. The blades, when wings in operational position, are rigid with one another after some assembly. When the implement is folded the width is reduced to nine feet.

Towards A Fast Reconstruction Paradigm For Urban Environments In Developing Regions Affected By Natural Disasters, Christopher Maestri

Civil Engineering Undergraduate Honors Theses

Natural disasters in developing regions often displace people from their homes, into temporary shelters. These temporary shelters often consist of single-story pre-assembled tents designed to provide short-term aid for individual families. Unfortunately, single-story temporary shelters are not sufficient for accommodating large displaced populations in urban settings due to issues of land overcrowding and disruption to utilities providing water sanitation and hygiene (WASH) services (along with many other issues).

This study investigates the feasibility of implementing a multi-story steel structure, constructed with multi-use structural members and special end connectors, into future relief efforts. A multi-use structural member is an element whose …

Analysis Of Bolted Beam-Column Connections With Multiple Bolts Per Row And Column Web Stiffeners, Benjamin C. Sutherland

Civil Engineering Undergraduate Honors Theses

Bolted beam-column connections are a common moment connection used in the design of steel buildings. Existing design guides include design parameters for bolt configurations having one bolt on either side of the beam web for each row of bolts. There is potential for increasing connection strength by adding additional bolts on the outside of these rows. This addition could be useful in retrofit scenarios, or even in the design of new structures. In this research, finite element analysis is used to analyze various beam-column connections and t-stub connections. The modeling methods, research process, and conclusions are explained in the thesis …

Volume-Change Restraining Effects In Continuous Precast/Prestressed Bridge Girders, Athul Alex

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

A variety of design and construction practices are feasible when building precast concrete continuous bridges with long spans. Precast, prestressed concrete continuous bridges have been implemented by countries around the world. Although these bridges have been in service for many years, there has been limited verification of the ability of connection to provide the predicted continuity. Subsequently many states in the United States design the girders as simple spans for both dead and live loads without considering any moments developed by the connection. The effect of thermal expansion and contraction is hardly considered in the analysis, even though it is …

Performance Assessment Of Deteriorated And Retrofitted Steel Hp Piles, Steven T. Stauffer

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Deterioration of aging bridges can be attributed to an assortment of mechanisms throughout the structure, with remediation policies also varying. This study focused on assessing the validity of the Nebraska Department of Roads’ (NDOR) reinforced concrete encasement retrofit for corroded steel HP piles. Experiments were designed and conducted to test the capacity of the NDOR retrofit and evaluate failure limit states. Two pile locations were considered: abutment and pile bent. For each location there was a non-deteriorated, deteriorated, and retrofitted case. These cases represented the pile at key stages during its life. NDOR’s concrete encasement retrofit provided the required stability …

Evaluation Of Alternative Implementation Methods Of Failure Sampling Approach For Structural Reliability Analysis, Kapil Patki, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

In this paper, several alternative approaches are used to implement the failure sampling method for structural reliability analysis and are evaluated for effectiveness. Although no theoretical limitation exists as to the types of problems that failure sampling can solve, the method is most competitive for problems that cannot be accurately solved with reliability index-based approaches and for which simulation is needed. These problems tend to have non-smooth limit state boundaries or are otherwise highly nonlinear. Results from numerical integration and three extrapolation approaches using the generalized lambda distribution, Johnson's distribution, and generalized extreme value distribution are compared. A variety of …

Improved Methodologies In Modeling And Predicting Failure In Aashto M-180 Guardrail Steel Using Finite Element Analysis, Phase I, Brandt M. Humphrey

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Steel guardrail systems have historic and widespread applications throughout the nation’s highways and roadways. However, catastrophic system failure can occur if the guardrail element ruptures, thus allowing an errant vehicle to pass uncontrolled through the system and potentially allow fractured ends to pierce the occupant compartment. To aid in the analysis and design of guardrail systems, further efforts are needed to develop and implement more reliable material failure criteria to predict and model guardrail steel rupture under all vehicle impact loading scenarios within impact simulation finite element method (FEM) software, such as LS-DYNA.

This Phase I study accomplished a number …

Structural Evaluations Of Bridges With Smartphones, Garrett P. Martindale, Dean Whitfield, Jeremiah Dixon

UCARE: Research Products

According to the 2013 Report Card for America’s Infrastructure, published by the American Society of Civil Engineers (ASCE), the United States has a bridge rating of C+. The C rating is classified by ASCE as a mediocre standing. Infrastructure that is awarded the C rating shows general signs of deterioration and requires attention.

Our Hypothesis: Smartphones have become readily available to anyone and is a relatively cheap device. They have instruments within them that can capture and collect usable data. An application can be downloaded to record the smartphone’s acceleration. The acceleration data can be used to evaluate vibrations within …

Decay Of Pressure Fluctuation In The Hyporheic Zone Around A Cylinder, Timothy Calappi, Carol J. Miller

Civil and Environmental Engineering Faculty Research Publications

Erosion around a submerged cylinder is a well-studied problem, and is of particular interest in bridge pier scour applications. Particles erode when lift and drag forces overcome a critical threshold. These forces are typically studied from above the water-riverbed interface and are related to geometry and surficial processes. The present study maps hyporheic pressure fluctuations as they are related to surface water velocity fluctuations. Relatively, high-pressure events in the subsurface promote a destabilizing force from within the riverbed and increase the potential for the mobilization of sediment. Differential pressure transducers were fitted within a vertical cylinder in a movable bed …

A Comparison Of American, Norwegian, And Russian Standards In Calculating The Wall Thickness Of Submarine Gas Pipeline, Cindy Dianita, Tatyana Vladimirovna Dmitrieva

Makara Journal of Technology

One of the key issues in the pipeline design is wall thickness calculation. This paper highlights a comparison of wall thickness calculation methods of submarine gas pipeline based on Norwegian Standard (DNV-OS-F101), Indonesian Standard SNI 3474 which refers to American Standard (ASME B31.8), and Russian Standard (VN39-1.9-005-98). A calculation of wall thickness for a submarine gas pipeline in Indonesia (pressure 12 MPa, external diameter 668 mm) gives the results of 18.2 mm (VN39-1.9-005-98), 16 mm (ASME B31.8), and 13.5 mm (DNV-OS-F101).The design formula of hoop stress due to internal pressure is interpreted in different ways for every standard. Only Norwegian …

Developing Standard Procedures For Structural Aspects Of Slide-In Bridges In Accelerated Bridge Construction (Abc), Ozan Utku Ridvanoglu

Masters Theses

Slide-in bridge construction (SIBC) is a special method especially used to replace an existing bridge with the minimum duration road closure. In this method, new bridge superstructure is built next to the existing one and it is slid to its final position after demolishing the existing one. Applied implementations of SIBC show that several complications are experienced during bridge slide related with surface interaction. There is a need to evaluate the structural components of SIBC to develop suggestions. In this research, structural components of SIBC were investigated. The research dealt with completed SIBC implementations and numerical modelling of the slide …

Texture Analysis Using The Neutron Diffraction Method On The Non Standardized Austenitic Steel Process By Machining,Annealing, And Rolling, Tri Hardi Priyanto, Parikin Parikin, Meijuan Li

Makara Journal of Technology

Austenitic steel is one type of stainless steel which is widely used in the industry. Many studies on austenitic stainless steel have been performed to determine the physical properties using various types of equipment and methods. In this study, the neutron diffraction method is used to characterize the materials which have been made from minerals extracted from the mines in Indonesia. The materials consist of a granular ferro-scrap, nickel, ferro-chrome, ferro-manganese, and ferro-silicon added with a little titanium. Characterization of the materials was carried out in three processes, namely: machining, annealing, and rolling. Experimental results obtained from the machining process …

Post-Repair Seismic Assessment Of Rc Bridges Damaged With Fractured Column Bars - A Numerical Approach, Ruili He, Yang Yang, Lesley H. Sneed

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Seismic repair of reinforced concrete (RC) bridge columns has been studied extensively during the past several decades; however, few studies have been conducted on the influence of the column repair (member level) on the post-repair performance of bridge structures (system level). In a previous experimental study by the authors, a method was developed to rapidly repair severely damaged RC bridge columns to enable the quick reopening of the bridge to emergency traffic. Thus, a lower limit state was used for the repair design, so that the lateral strength and drift capacity of a repaired RC column with fractured longitudinal bars …

Cyclic Behavior Of A Hybrid Light Gauge And Hss Mezzanine Structural System, Michael John Kren

Master's Theses (2009 -)

Cold-formed steel is emerging as an alternative material in the building industry to hot-rolled steel for smaller buildings and indoor structures also called mezzanines. Cyclic testing of a full-scale mezzanine structures composed of cold-formed structural channel beams connected to hollow structural steel (HSS) columns cap plates using wedge expansion anchors at the base plate to generate rotation restraint, is performed in this research. The characteristics of the structure will be explained by displaying full experimental results of structural testing. Unfortunately, limited experimental data outlining the behavior of these structures is available and design criteria is very limited. Thus, there is …

Thermal Properties, Crystallinity, And Oxygen Permeability Of Na-Montmorillonite Reinforced Plasticized Poly(Lactic Acid) Film, Kurniawan Yuniarto, Yohanes Aris Purwanto, Setyo Purwanto, Bruce A. Welt, Hadi Karia Purwadaria, Titi Candra Sunarti

Makara Journal of Technology

Introducing unmodified organically clay/Na-montmorillonite (Na-MMT) was applied into plasticized poly(lactic acid) PLA to produce film composites by direct casting. Film composite structure, the crystallinity degree and form, and thermal properties were carried out using X-ray diffraction and differential scanning calorimetry. The effect of Na- MMT to the tortuous path and the crystallinity degree in the plasticized film composites were calculated in oxygen barrier properties. Chromatogram film composites resulted in an intercalated structure that showed peak diffraction angle shift at about 0.2o. Then, a peak diffraction pattern was indicated in α-form crystal structure. Plasticized PLA has a crystallinity degree at 34%, …

Residual Strength Analysisof Asymmetrically Damaged Ship Hull Girderusing Beam Finite Element Method, Muhammad Zubair Muis Alie

Makara Journal of Technology

The objective of the present study is to analyze the residual strength of asymmetrically damaged ship hull girder under longitudinal bending. Beam Finite Element Method is used for the assessment of the residual strength of two single hull bulk carriers (Ship B1 and Ship B4) and a three-cargo-hold model of a single-side Panamax Bulk Carrier in hogging and sagging conditions. The Smith’s method is adopted and implemented into Beam Finite Element Method. An efficient solution procedure is applied; i.e. by assuming the cross section remains plane, the vertical bending moment is applied to the cross section and three-cargo-hold model. As …

Maneuverability Of Ships With Small Draught In Steady Wind, Daeng Paroka, Andi Haris Muhammad, Syamsul Asri

Makara Journal of Technology

Wind force and moment may force a ship to drastically decrease its speed and use a large drift angle as well as a large rudder angle in order to maintain its course. Ships with a small draught might have more risk in maneuvering to its point of view compared with a ship with a larger draught. This paper discusses maneuverability of a ship with a small draught in steady wind. The effect of wind on ship speed, drift angle, and rudder angle are investigated in a steady state condition. Five different ratios of wind velocity to ship speed from 1.0 …

Discrete Power Control In Heterogenous Networks, Yuanyuan Wang, Wibowo Hardjawana, Branka Vucetic

Makara Journal of Technology

In heterogeneous networks (HetNets) where femtocell base stations (FBSs) are deployed within the radio coverage of macrocell base stations (MBSs) to increase network capacity, co-channel interference limits overall system performance with universal frequency reuse. This paper investigates new distributed downlink discrete power control scheme for FBSs in HetNets with FBSs cooperation. The objective of the proposed power control scheme is to maximize the number of simultaneous FBSs transmissions in a single transmission wireless channel where each FBS is allowed to transmit only if the signal-to-interference-noise ratio (SINR) requirements for both FBSs and MBS users are satisfied. We apply a stochastic …

Multi-Project Scheduling Cost Optimization In A Machine Manufacturer Engineer-To-Order, Farizal Farizal, Amar Rachman, Tifani Tandean, Sumarsono Sudarto, Katsuhiko Takahashi

Makara Journal of Technology

This paper discusses the utilization of mixed integer linear programming (MILP) model to optimize cost for multiproject scheduling in a machine maker company. The objective is to minimize total project’s penalty cost and labor cost. The model formulated shows how to achieve the objective i.e. whether to use outsourcing or overtime to finish all projects. The model of multi-project scheduling was solved by Branch & Bound algorithm coded in Lingo 14.0 software. The case study shows that if a company wants to minimize lateness, it should use overtime instead of outsourcing, which minimize total lateness of projects by 144 days …