Civil and Environmental Engineering Commons^™

Mechanical Properties Of Alkali‑Activated Slag‑Fly Ash Geopolymers, Liu Yang, Wang Jizhao, Lu Naiwei, Wang Bowen

Journal of China & Foreign Highway

In order to respond to the national strategy of energy saving and emission reduction and improve the comprehensive utilization rate of industrial waste，the influence of slag content，alkali equivalent，sodium silicate modulus，and water-cement ratio on the compressive strength of slag-fly ash geopolymers was investigated by single variable and orthogonal experiment method.The compressive strength of geopolymers was analyzed by combining XRD，SEM，and porosity.The results show that the gel formation is promoted with the increase in slag content，and the structure of geopolymers is more compact，which is conducive to the development of strength.After 28 days of standard curing，the influence of various factors on the compressive strength …

Mechanical Properties Of Geopolymer‑Stabilized Recycled Aggregates From Construction Solid Wastes, Yuan Kaixin, He Yongjian, Zhang Laijun, Li Hai, Xu Gewei

Journal of China & Foreign Highway

In order to solve the problem of a sharp increase in construction solid wastes and insufficient utilization rate，this paper took slag-fly ash-based geopolymer as an inorganic binder，replaced natural gravels with recycled aggregates from construction solid wastes，and set urban road base layer as the target scene to study the mechanical properties of geopolymer-stabilized recycled aggregates at different contents.The results show that with the increase in geopolymer content，the maximum dry density of the mixture increases.The optimum moisture content increases.The unconfined compressive strength of the mixture increases with the increase in geopolymer content and curing age and decreases with the increase in recycled …

Comparative Experimental Study On Deformation Characteristics Of High Liquid Limit Soil Under Different Dry And Wet States, Qin Lingwei, Zhang Rui, Li Lu, Xiao Yupeng

Journal of China & Foreign Highway

In order to further reveal the internal mechanism of the influence of solid-like bound water on the deformation characteristics of high liquid limit soil，the difference in the influence of different bound water contents on the deformation of soil samples was analyzed through the comparison of dry and wet sides.Four types of high liquid limit soil with different water contents at the same dry density were used，and a low liquid limit soil was used as a comparison sample to carry out a deformation test.The volumetric flask method was used to test the content of adsorbed bound water in each test soil …

Influence Of Loading Methods On Compression Modulus Of Red Sandstone Soil Solidified With Biological Enzyme And Cement, He Liang, Zhang Haixiang, Guan H Ongxin, Li Huili, Yang Hairong, Liu Hongfu

Journal of China & Foreign Highway

There are various methods to test the modulus of cement-stabilized mixtures.The stiffness performance of cement-stabilized materials will be affected after adding biological enzymes.In order to systematically analyze the influence of loading conditions on the compression modulus of the red sandstone soil solidified with biological enzyme and cement，compressive modulus tests were conducted on the red sandstone soil solidified with biological enzyme and cement by using three static modulus test methods including monotonic loading method of middle section，stepwise loading and unloading method of top surface，and stepwise loading and unloading method of middle section，as well as dynamic modulus method of top surface and …

Optimization Of Mix Proportion For New Jersey Precast Concrete Safety Barriers And Performance Tests Under Integral Concrete Vibrating, Chen Lin, Li Beian, Li Yuanrui, Zhao Zixiang

Journal of China & Foreign Highway

New Jersey safety barriers are the most commonly used form of guardrails in highway median separators due to their excellent safety protection.In response to the cost reduction and quality improvement，efficient and rapid preparation process，and quality issues of New Jersey precast concrete safety barriers，this article adopted the automation production process of New Jersey precast safety barriers，optimized concrete mix proportion for precast safety barriers，and studied their performance.The experimental results show that in the designed C 30 concrete，the compressive strength of the concrete mixed with 15% fly ash reaches 39.2 MPa，and th e slump reaches 185 mm.The concrete performance meets the requirements of …

Experimental Study On Shear Behavior Between Nrc‑Uhpc Interface, Chen Zhenkan, Li Junsheng, Shi Quan, Fang Haozhen, Mo Fan, Jiang Haibo

Journal of China & Foreign Highway

In order to investigate the effect of the screw diameter of planted bars and ultra-high performance concrete （UHPC） pouring method on the shear behavior of normal reinforced concrete （NRC） and UHPC， two groups of six push-out specimens were designed for shear behavior tests.The results show that after the failure of the concrete bonding force in the NRC-UHPC interface，the screw can maintain shear behavior so that the failure process of the specimen after the load reaches the peak shows ductile characteristics.For specimens with screw diameters of 12 mm and 16 mm，greater screw diameter indicates higher shear capacity of the specimens and …

Design And Construction Process Of Cross‑Beam Supports For Main Tower Of Changtai Changjiang River Bridge, Zeng Jian, Hu Pei, Wang Chao

Journal of China & Foreign Highway

The construction of the lower cross-beam structure of the main tower of Changtai Changjiang River Bridge has the characteristics of high construction height，large amount of concrete earth volume，and difficult control of down-warping deformation.In order to implement the pouring of the lower cross-beam of the main tower，floor-type steel pipe supports were set at the lower cross-beam，which were used to support the lower cross-beam formwork and bear the load during the concrete pouring.Through the finite element software analysis and calculation，it was found that the asymmetric deformation of the main structure of the lower cross-beam could be effectively controlled，and the overall force of …

Determination Of Manufacturing Parameters Of Large Section Of Continuous Steel Box Beam With Variable Section In Shenzhen‑Zhongshan Passage, Dong Chuangwen, Chen Long, Li Chuanxi

Journal of China & Foreign Highway

Accurate calculation of manufacturing parameters is the key to the efficient，high-precision，and rapid installation of large sections of continuous steel box beam bridges.Taking the steel box beam with the variable section in Shenzhen-Zhongshan Passage as the background，this paper first established a finite element model of the beam element in the whole construction process to obtain the pre-camper.Secondly，the average neutral axis position was calculated based on the height of the neutral axis of each beam section.Then，according to the deformation characteristic that the beam length remained unchanged at the mean neutral axis，the pre-camber was superimposed at the mean neutral axis to get the …

Key Technology For Construction Of New Single‑Wall Steel Suspended Box Cofferdam With High Pile Tied Beams In Deep Water, Yang Jinlong, Zhao Lin, Jiang Qunlong

Journal of China & Foreign Highway

In order to ensure the safe，efficient，and economical completion of the construction of the high pile tied beam of Muping Xiangjiang River Bridge in deep water，a new type of single-wall steel suspended box cofferdam was designed to act as the water retaining and enclosure structure during high pile tied beam construction according to the characteristics of deep water level and shallow stratum cover layer at the high pile tied beam location.Through the innovative design of steel casing on the bottom of the steel suspended box cofferdam，the design height of the wall panel and the amount of steel input were reduced.On the …

Influence Factors Of Carbonization Of Tunnel Segment Structure And Life Prediction Analysis, Li Dongbiao, Miao Miao, Shen Caihua, Chen Wei

Journal of China & Foreign Highway

There are many factors that affect the carbonization life of concrete segments in underwater tunnels，and the prediction methods are not uniform.In this paper，combined with actual engineering，the influencing factors and laws of carbonization of concrete segments in underwater tunnels were analyzed，and three methods for predicting the life of concrete segments were established with the crack limit as the control target.The prediction results of the three methods were compared.The results show that the influence of the temperature and CO2 concentration in the tunnel predicted by the three methods on the life of the tunnel lining structure is basically consistent with the existing …

Key Technology For Incremental Launching Construction Of Double Guide Beam Of Steel Box Girder, Sun Xiaoqiang, Yue Xinxing

Journal of China & Foreign Highway

By taking the incremental launching construction of the steel box girder at the 6th hole of the approach bridge of Baoji Taigu Bridge as the engineering background，the original plan adopted single-guide beam multi-point walking incremental launching technology for assembly and incremental launching on the prestressed reinforced concrete beam of the adjacent hole.Since the middle span of the concrete beam cannot withstand the concentrated force at the incremental launching points，the multi-guide beam multi-point walking incremental launching technology was finally used to arrange the incremental launching points at the transverse diaphragm plate of the end of the concrete beam.By increasing the incremental …

Emergency Vehicle Dispatching Model Considering Demand Urgency And Delivery Fairness, Long Kejun, Liu Jia, Gao Zhibo, Chen Suqian, Zhang Zhonggen

Journal of China & Foreign Highway

In emergency vehicle dispatching after unexpected events，it is crucial to prioritize critical nodes with high demand urgency while minimizing excessive delivery delays at other nodes to prevent secondary impacts.On this basis，this study developed an emergency vehicle dispatching model that considered demand urgency and delivery delay fairness.Firstly，the entropy weight-TOPSIS method was used to calculate the demand urgency for each node，and a delivery delay balance index was introduced to minimize disparities in delivery delays between nodes.Secondly，a multi-objective optimization model was established with total delivery time，overall cost，and delivery delay balance as objectives，while considering constraints such as inventory levels at distribution centers and route …

Working Properties Of Steel Tube Batter Piles With Concrete Infill Based On Abaqus, Yang Meiliang, Li Liemin, Sun Kunjiang, Han Rui, Zhong Yang

Journal of China & Foreign Highway

In order to explore the respons e characteristics of steel tube batter piles with concrete infill under vertical load，the steel tube batter pile with concrete infill used in Saribas Bridge in Malaysia was taken as the research object.Based on the numerical simulation method，the frictional resistance of the inner and outer walls of the steel tube，the frictional resistance around the pile at the section，and the bending moment bearing ratio between the steel tube and the concrete core of this type of batter pile under vertical load were studied.The results show that the passive-side frictional resistance of the 0–15 m pile section …

Sustainability Assessment Of Photovoltaic Cells In Cross-Functional Applications, Achyuth Ravilla

Dissertations and Theses

Achieving the G7 countries' net-zero emissions target by 2050 requires integrating photovoltaic (PV) systems into diverse cross-functional applications that support sustainable energy transitions across multiple sectors. This dissertation explores the economic and environmental sustainability of three such applications: agrivoltaics, lower-dimensional materials in perovskite solar cells, and PV-electrochemical water-splitting technologies for hydrogen production. Employing life cycle assessment (LCA) and techno-economic analysis (TEA), we address the knowledge gap in comprehensive evaluations of PV-integrated solutions.

The first chapter assesses agrivoltaic systems (AVS), which combine PV systems with agriculture to mitigate land-use conflicts while enhancing food and energy production. Findings indicate that AVS designs, …

Interpreting Strain Caused By Transient Well Testing, Soheil Roudini

All Dissertations

Understanding reservoir properties and structure is essential to managing subsurface operations, such as geologic storage of CO₂ or production of water, hydrocarbons or heat. Previous work demonstrated the potential of analyzing strain data during transient well tests by estimating hydraulic diffusivity using a type-curve-like approach. The following dissertation aims to pursue this potential by developing and evaluating methods for interpreting strain tensor data to improve subsurface characterization. The research advances the classic, intuitive method of using type-curves to interpret well tests, but it also brings together modern computational methods from machine learning, proxy modeling and Bayesian inversion, and it …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-Based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO₂, MoS₂, and Al₂O₃) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment …

A Strategic Insight Into The Market For Carbon Management Capacity, Mahelet G. Fikru, Ting Shen, Jennifer Brodmann, Hongyan Ma

Economics Faculty Research & Creative Works

This study presents the market for carbon management capacity via carbon capture, utilization, and storage technologies, identifying demand and supply forces, as well as clarifying the potential impact of market and non-market-based shocks on technology developers versus adopters. The paper addresses a prevailing gap in market analysis, introducing a microeconomic framework and unique dataset to identify key players, market forces, and policy incentives shaping the carbon capture, utilization, and storage landscape. The analysis equips industry stakeholders, policymakers, and investors with valuable insights regarding (1) leaders in the design, development, and manufacture of carbon capture, utilization, and storage technologies (supply), (2) …

Fitting Quality Of Nmr Relaxation Data To Differentiate Asphalt Binders, Rebecca M. Herndon, Kevin Lai, Magdy Abdelrahman, Klaus Woelk

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Asphalt binder performance grades (PGs) are important metrics in designing pavements for effective transportation infrastructure. the PG system relies on the binder's stiffness and is determined through energy- and time-intensive physical testing. Physical properties, like stiffness, can also be determined by spin–lattice NMR relaxometry, a non-destructive chemical method. NMR relaxometry can quantify the molecular mobility of materials by determining relaxation times from exponential decays of excited nuclear magnetization. While relaxation times have been used to determine physical properties of materials, a quantitative relation to the PG grades of asphalt binder is yet to be established. in this study, T1 NMR …

Basic Safety Message Generation Through A Video-Based Analytics For Potential Safety Application, Abyad Enan

All Theses

With the advancement of modern artificial intelligence techniques, computer vision can play a vital role in enhancing roadway safety by reducing the risk of imminent collisions. To do so, a vision-based safety application is required, where a roadside camera can monitor the roadway traffic and predict potential risks of crashes in real-time. If any risky situation or behavior is observed that may lead to a crash, then a safety application can send warnings to the vehicles at risk. For vision-based safety applications on a roadway section, it is important to accurately monitor each vehicle’s location, speed, acceleration, heading direction, etc. …

Thermal Conductivity Characterization Of High Oleic Vegetable Oils Based Hybrid Nanofluids Formulated Using Gnp, Tio2, Mos2, Al2o3 Nanoparticles For Mql Machining, Anthony Chukwujekwu Okafor, Tobechukwu Kingsley Abor, Saidanvar Esanjonovich Valiev, Ignatius Echezona Ekengwu, Abiodun Saka, Monday Uchenna Okoronkwo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents the results of thermal conductivity characterization of six high oleic soybean oil (HOSO) and four high oleic canola oil (HOCO)-based hybrid nanofluids formulated with four types of nanoparticles (Graphene nanoplatelet (xGnP), TiO2, MoS2, and Al2O3) at nanoparticles wt.% concentration from 1 % to 7 % in 1 % increment using the two-step method for use in MQL machining of difficult-to-cut metals. Thermal conductivity of the formulated hybrid nanofluids were measured using Thermtest Transient Hot Wire Liquid Thermal Conductivity Meter at temperatures from 25 °C to 75 °C in increment of 10 °C. Obtained results showed that thermal …

Uptake Of Contaminants Of Emerging Concerns (Cecs) By Plants Irrigated With Recycled Waters, Abid Hussain

UNLV Theses, Dissertations, Professional Papers, and Capstones

The increasing demand for water in arid and semi-arid regions necessitates the use of recycled water (RW) for irrigation. RW is a viable alternative to conventional irrigation water at most locations, but it can be a major route for contaminants of emerging concerns (CECs) to be taken up by the tissues of food crops, thereby leading to their subsequent entry into the food chain. CECs include pharmaceuticals, personal care products, and industrial chemicals that are generally present at low concentrations in environmental waters, hence their common designation as trace organic compounds (TOrCs), and CECs also include microbiological constituents such as …

Quantitative Evaluation Of Baseflow Separation Methods Using An Integrated Hydrologic Model: A Case Study In A Snow-Dominated Watershed, Jihad Othman

All Graduate Reports and Creative Projects, Fall 2023 to Present

Baseflow, commonly referred to as the groundwater contribution to streamflow, constitutes approximately 50% of streamflow in mountainous regions of the Western United States. Accurately quantifying the amount of baseflow is critical for water management and decision-making, as it significantly impacts stream water quality, low flow availability, and ecosystem health. Traditionally, baseflow has been estimated using conceptual and automated baseflow separation methods, which are known to be both arbitrary and ambiguous, posing a challenge to validate them. In this study, we developed an integrated hydrologic model that seamlessly integrated the exchange between surface and subsurface flows to physically quantify the baseflow …

Deep Learning Vision-Based Bridge Inspection With Resource-Constrained Unmanned Aircraft Systems, Ji Young Lee

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Bridge inspection is critical for ensuring structural integrity, extending the service life of infrastructure, and minimizing maintenance costs. As bridges age and endure increasing loads, regular inspections help detect early signs of wear, such as cracks or corrosion, that could impact safety and performance. However, traditional inspection methods are labor-intensive, requiring significant time, specialized equipment, and manual access to challenging areas, which can lead to costly disruptions. Additionally, reliance on human inspectors introduces subjectivity, with assessments varying by individual expertise. These factors highlight the inefficiencies and safety risks in current inspection practices, underscoring the need for more objective, efficient solutions. …

Landslide Inventory And Unstable Slope Monitoring Along Highways In Eastern Tennessee, Robert Mcsweeney

Electronic Theses and Dissertations

This research introduces an unstable slope management program (USMP) for Tennessee based on federal slope management standards, along with improved methods for landslide monitoring with unmanned aerial systems (UAS) lidar and photogrammetry. In mountainous regions, monitoring slope hazards is a critical function of transportation management. A mobile field assessment form created with Survey123 was used to collect 22 unstable slope ratings in eastern Tennessee. Location points were appended with photographs, notes, and site information. Landslide scores ranged from 325 (Fair) to 1005 (Poor). UAS monitoring of a slow-moving soil landslide along I-40 near Rockwood, TN, produced high-resolution lidar and photogrammetry …

Supporting Holistic, Informed, Decision-Making Through The Complementarity Of Life Cycle Assessment And Radiological Protection, Bryanna Wattier-Weisensee

All Dissertations

Decision making is challenging and it is necessary to consider all relevant data to make an informed decision. The work herein provides a pathway wherein the fields of radiological protection and life cycle assessment (LCA) can be utilized synergistically to benefit the decision-making using the other (and vice versa). Specifically, LCA parallels decision-aiding techniques used in the optimization of radiological protection and LCA includes an ionizing radiation potential (IRP) impact category wherein the impacts associated with an emission of radioactive material is quantified to determine the human health impact. Thus this body of work focuses on (1) expanding the platform …

Evaluation Of 3d Beach Profiles: A New Method For Monitoring Changes In Beach Morphology And Grain Size, Kalinda Ellen Roberts

Graduate Masters Theses

Beach profiles are a simple and affordable approach to monitoring changes in beach morphology. However, traditional methods offer limited resolution and dimension. Recent advancements in technologies, particularly structure-from-motion (SfM) and grain size detection models (GSDMs), can be integrated into conventional beach profiling techniques, enabling more detailed spatial and temporal analysis of slope and grain sizes. This research introduces a new technique for coastal monitoring, termed “3D Beach Profiles,” which integrates SfM technology to create high-resolution three-dimensional digital surface models (DSMs) and orthomosaics of beach surfaces. These digital surfaces enable the extraction of beach slopes with orders of magnitude more data …

Biochar/Hydrochar Applications In Disinfection Byproduct Removal For Drinking Water, Ashleu Mussio Marquez, Donna Rouhani, Ismail Abdulraheem, Kers Ung-Watson, Ahmadreza Khatamgooya, Scarlet Nelson, Dr. Jaeyun Moon, Dr. Erica Marti

Undergraduate Research Symposium Posters

This project aims to investigate the process of disinfection byproduct (DBP) removal in drinking water, looking into the applications of biochar and hydrochar, which are low cost and environmentally sustainable adsorbents. These carbon-based adsorbents are derived from agricultural waste biomass, such as walnut shells. These adsorbents will be used to capture and remove contaminants in water, such as DBPs. DBPs are formed when chemical disinfectants react with organic and inorganic substances naturally present in water. The targeted DBPs for adsorption include trihalomethanes, haloacetic acids, haloacetonitriles, and nitrosamines. An example of high concentration DBP formation is during emergency chlorination, where excess …

Evaporation Basins For Salinity Management, Department Of Primary Industries And Regional Development, Western Australia

Natural resources factsheets

An evaporation basin is an engineered earth structure designed to safely store and evaporate saline water discharged from drainage or pumping, while protecting high-value agricultural land, natural assets or built infrastructure.

DPIRD recommends that evaporation basins should form part of an integrated water and salinity management program. Information on this page is a guide only.

It is recommended that landholders seek expert advice plus engineering design and related support from qualified contractors.

The Effects Of Wildfires On The Mental And Physical Health Of School-Age Children In North America: A Scoping Review, Sarah Oerther, Sarah Manspeaker, Alison Wix, Daniel Oerther, Carmen Marsit

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Background: Wildfires are occurring more often and with greater intensity, leading to longer and harsher fire seasons. As a result, children are more frequently exposed to wildfire smoke, which increases their risk of mental and physical health effects. Purpose: The purpose of our scoping review is to explore the current literature on what is known about the direct and indirect impacts of wildfires on the mental and physical health of school-age children in North America (5 to 18-year-olds). Methods: A health sciences librarian-assisted literature search, with input from the research team, was performed. Results: A total of 16 studies were …

Roaded Catchments In Wa, Department Of Primary Industries And Regional Development, Western Australia

Natural resources factsheets

Roaded catchments are earthwork structures designed to increase the amount of run-off from the catchment above a receiving farm dam.

Roaded catchments are lined with clay and compacted to make a smooth surface that reduces infiltration and increases run-off. Roaded catchments should discharge into a silt trap and then into a dam (excavated earth tank). This combined structure should be fenced to exclude livestock.

The Department of Primary Industries and Regional Development recommends that roaded catchments are part of an integrated water and salinity management program.

The information in this page is only a guide – seek expert advice before …