Civil and Environmental Engineering Commons^™

Biological Reduction Of Perchlorate In Ion Exchange Regenerant Solutions Containing High Salinity And Ammonium Levels, Tina M. Gingras, Jacimaria R. Batista

Civil and Environmental Engineering and Construction Faculty Research

The most promising technologies to remove perchlorate from water are ion exchange and biological reduction. Although successful, ion exchange only separates perchlorate from water; it does not eliminate it from the environment. The waste streams from these systems contain the caustic or saline regenerant solutions used in the process as well as high levels of perchlorate. Biological reduction could be used to treat the regenerant waste solutions from the ion exchange process. A treatment scheme, combining ion exchange and biodegradation, is proposed to completely remove perchlorate from the environment. Perchlorate-laden resins generate brines containing salt concentrations up to 6% or …

Membrane Ultrafiltration Of Treated Palm Oil Mill Effluent (Pome), Pui Wah Wong

Student Works (2000-2009)

The common practice for treatment of palm oil effluent (POME) in Malaysia employs a combination of aerobic and an anaerobic treatment. Bearing in mind that the quantity of POME produced is high, reaching 740 000 m3 in May 2001, reuse and recycling of treated POME can be an excellent practice in terms of saving of water resources. As the treated POME is already low in certain parameters required by the Department of Environment (i.e. BOD, total and ammoniacal nitrogen, oil and grease), further treatment will greatly enhance the water quality. The purpose of the advance treatment step is to allow …

A Dynamic Simulation Model Of Beach Sand Replenishment: A Case Study Of Santa Barbara, California, David Turbow, Steve Norwick, Sajjad Ahmad

Civil and Environmental Engineering and Construction Faculty Research

Sediment deprivation from dam installments contributes to beach erosion yet the underlying physical and economic factors linking them together have traditionally been isolated during regional planning. In order to gain a better understanding of the behavior of a managed beach system, a dynamic simulation model was developed incorporating physical and monetary factors influencing the amount of available beach sand. The Santa Barbara littoral cell was chosen as a case study to evaluate the feasibility of beach preservation goals under scenarios in which annual sand replenishment funding, sand prices, or sediment recovery from behind dams were limiting factors to available beach …

Upper Spokane River Model: Model Calibration, 1991 And 2000, Chris Berger, Robert Leslie Annear, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to:

• Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam. • Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics)

This report evaluates the model calibration and discusses issues relative to that calibration effort. …

Impact Of Land Use Change On Hydroelectric Power Generation In Cameron Highlands, Fook Kun Choy

Student Works (2000-2009)

This study assesses the impact of land use changes on annual energy production of the hydro stations of Cameron Highlands Hydroelectric Scheme. Land use affects sediment load and streamflow of Sungai Telom and Sungai Bertam, which influences power generation and energy production of the several hydro stations in Cameron Highlands. Data of rainfall, streamflow, suspended sediment load, land use and energy output for the period 1964 to 1998 were collected, processed and analysed. Regression analysis, double mass curve method and double ratio technique were used in the assessment. The suspended sediment load and annual runoff of Sungai Telom and Sungai …

Assessment Of Pollution Load For Approved Eia Projects In The Industrial Sector (1988-1998) In Malaysia, Kok Sia Teng

Student Works (2000-2009)

It is generally recognised that developing countries lacked quantitative decision support tools in the formulation and implementation of pollution control measures necessary to abate environmental impacts associated with industrial development. Reliable and comprehensive simulation models are needed as basic tools for the quantification of industrial pollutant emission load, the assessment of their impacts on the environment as well as the evaluation of pollution control options. As a response to this inadequacy, this research project is conducted as an initial endeavor to use the World Bank's industrial pollution projection program Decision Support System for Integrated Pollution Control (DSS/IPC) for the assessment …

Lower Willamette River Model: Model Calibration, Chris Berger, Robert Leslie Annear, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

Water Environment Services of Clackamas County is in the process of planning upgrades on several of its wastewater treatment plants (WWTPs) which discharge into the Lower Willamette River. The goals of the modeling effort were to:

• Gather data to construct a computer simulation model of the Lower Willamette River system in order to evaluate the impact of the WWTP discharges on water quality

• Ensure that the model accurately represents the system physics and chemistry (flow, temperature, dissolved oxygen and nutrient dynamics) by model calibration

• Use the model to evaluate how to meet various future discharge scenarios for …

Upper Spokane River Model: Boundary Conditions And Model Setup, 1991 And 2000, Robert Leslie Annear, Chris Berger, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

The Washington Department of Ecology is interested in a water quality model for the Upper Spokane River system for use in developing Total Maximum Daily Loads (TMDLs). The goals of this modeling effort are to:

• Gather data to construct a computer simulation model of the Spokane River system including Long Lake Reservoir and the pools behind Nine Mile dam, Upper Falls dam and Upriver dam

• Ensure that the model accurately represents the system hydrodynamics and water quality (flow, temperature, dissolved oxygen and nutrient dynamics)

A hydrodynamic and water quality model, CE-QUAL-W2 Version 3 (Wells, 1997), is being applied …

Lower Willamette River Model: Boundary Conditions And Model Setup, Herman G. Rodriguez, Robert Leslie Annear, Scott A. Wells, Chris Berger

Civil and Environmental Engineering Faculty Publications and Presentations

Water Environment Services of Clackamas County is in the process of planning upgrades on several of its sewage treatment plants which discharge into the Lower Willamette River. The goals of the modeling effort are to:

• Gather data to construct a computer simulation model of the Lower Willamette River system including part of the Lower Columbia River and the Willamette River above the Oregon City Falls; Because of the tidal influence in the Lower Willamette River, portions of the Columbia River that might affect the Lower Willamette River water quality were also modeled. Also, a section of the Willamette River …

Ascent And Decompression Of Viscous Vesicular Magma In A Volcanic Conduit, Helene Massol, Claude Jaupart, Darrell Pepper

Mechanical Engineering Faculty Research

During eruption, lava domes and flows may become unstable and generate dangerous explosions. Fossil lava-filled eruption conduits and ancient lava flows are often characterized by complex internal variations of gas content. These observations indicate a need for accurate predictions of the distribution of gas content and bubble pressure in an eruption conduit. Bubbly magma behaves as a compressible viscous liquid involving three different pressures: those of the gas and magma phases, and that of the exterior. To solve for these three different pressures, one must account for expansion in all directions and hence for both horizontal and vertical velocity components. …

Baseflow Separation Based On Storage-Outflow Modelling Of Streamflow Recessions, With Application To Semi- Arid Catchments In Tanzania, S Mwakalila

Tanzania Journal of Engineering and Technology (TJET)

Discharge in many rivers is Often fed by baseflow provided by drainage of the saturated zone in the shallow permeable soils. It is becoming clear that the outflow from this saturated zone is not linear proportional to storage as is commonly assumed in many algorithms. The objectives Of this study theretore, are first to explore the extent to which the assumption of linearity in storage-outflow relationships is valid and secondly to introduce an alternative approach to baseflow separation algorithms for estimating direct mnoff time series. Numerical analysis Of streamflow recessions from the semi-arid catchments of the Great Ruaha basin in …

Water Infiltration Study On Slopes, Tian Huat Low

Student Works (2000-2009)

Study was carried out in the field using infiltrometer and in the laboratory using “sprinkler model”. Studies on infiltration have always been part of hydrology and Irrigation engineering. Infiltration forms the link between surface and subsurface hydrology. Infiltrated water must be quantified and subtracted from the surface runoff in flood prediction studies and surface water management. Numerous researchers have actually incorporated infiltration into the slope stability analysis of the residual soils, e.g., Othman (1990), Affendi et. al.(1992, 1996) and Suhaimi and Abdul Rahman (1997). In most analysis of slope stability, the infiltration rate of the slopes is assumed uniform throughout …

Statistical Properties Of Maximum Likelihood Estimates For Accelerated Lifetime Data Under The Weibull Model, Mahmoud A. Yousef

Doctoral Dissertations

Pipe rehabilitation liners are often installed in host pipes that lie below the water table. As such, they are subjected to external hydrostatic pressure. The external pressure leads to early deformation in the liners, which could ultimately lead to its failing or buckling before its expected service lifetime is achieved. Experiments involving long term buckling behavior of liners are typically accelerated lifetime testing procedures. In an accelerated testing procedure a liner is subjected to a constant external hydrostatic pressure and observed until it fails or for a certain time, t whichever occurs first. Liners that do not fail at time …

Unsteady Flow Model For An Irrigation Canal Network, Talaat Taher El Gamel

Civil & Environmental Engineering Theses & Dissertations

A mathematical model is developed to route unsteady flow through an irrigation canal network. The model is designed to handle branches, lateral inflow and outflow, sluice gates, and various boundary conditions. The model is developed for use on a personal computer. A specific irrigation canal network in Egypt is used as a case study to verify the model, and the results are presented. Full documentation is included in the appendix.

Determining The Value Of Groundwater Contamination Source Removal: A Methodology, Benjamin C. Recker

Theses and Dissertations

Subsurface contamination by industrial chemicals is one of the most prevalent and costly environmental problems facing the United States government. This contamination problem must be managed to protect human health and the environment. Two basic strategies are used to deal with subsurface contamination: source removal and contaminant containment. While much cost and performance data are available for individual technologies associated with each of these strategies, there have been very few studies that have examined the benefits of implementing source removal technologies in order to reduce contaminant containment (and hopefully total) costs. This study examines the tradeoff between extent of source …

A Model For Palladium Catalyzed Destruction Of Chlorinated Ethenes In Contaminated Groundwater, Christopher M. Stoppel

Theses and Dissertations

Groundwater contamination by chlorinated ethenes is a widespread environmental problem. Conventional remediation technologies have shortcomings that have prompted further research into the development of novel treatment technologies. A palladium/ alumina catalyst in the presence of dissolved molecular hydrogen (referred to hereafter as a PD/H₂ system) has been demonstrated to rapidly destroy chlorinated ethene contaminated groundwater. First-order kinetics have been used to model chlorinated ethene destruction in a PD/H₂ reactor. However, catalyst deactivation and regeneration are important processes that also need to be modeled in order to better understand their effect on treatment efficiency. This study presents a model …

Quantitative Validation Of A Model Of Chlorinated Ethene Natural Attenuation, Harold C. Young

Theses and Dissertations

Chlorinated ethenes are among the most prevalent groundwater contaminants at hazardous waste sites nationwide. In an attempt to manage the risks posed by these contaminants, while controlling costs, monitored natural attenuation (MNA) is being considered as a remediation strategy at many sites. MNA relies on naturally occurring physical, chemical, and biological processes in the subsurface to reduce the risk posed by the contamination. The implementation of MNA, however, requires a detailed understanding of these processes, and how they impact contamination at a particular site. One way to gain this understanding is through contaminant fate and transport modeling. In this study, …

Concrete Roughness Characterization Using Laser Profilometry For Fiber-Reinforced Polymer Sheet Application, Norbert H. Maerz, Poornima Chepur, John J. Myers, Justin Linz

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The failure of a reinforced concrete member strengthened with fiberreinforced polymer (FRP) laminates may be caused by crushing of concrete, rupture of FRP laminates, or delamination of the FRP sheet. Therefore, the effectiveness and failure mode of FRP sheets applied to beams and columns is related to the degree of adhesion of the epoxy to the concrete surface. When a peeling or delamination failure can be avoided, a more effective engagement of the FRP sheet occurs, which results in more efficient use of the material. One of the principal factors affecting the bond behavior between the concrete and epoxy is …

Development Of A Low-Cost, Self-Calibrating Stream Gaging Station, Gilberto Urroz, Robert C. Leines, Garryn L. Perret, Jared M. Holland, Brian E. Hunsaker

Reports

Executive Summary: The present report presents a review of the state-of-the-art technologies for the development of a low-cost, self-calibrating stream gaging station. The research was conducted by the Utah Water Research Laboratory with funding provided by the Utah Division of Water Resources through Project RP 110080, March 1998. The report presents a review of the current practices in stream gaging and how technologies such as remote data telemetry through the use of satellite, cellular phone communications, and radio telemetry can be used for the real-time transmission of data. The study also includes the use of Global Positioning System (GPS) for …

Studies On The Pollution Parameters Of Leachate From Ampang Landfill, Syed Fatimah Kamal Batcha

Student Works (2000-2009)

ln the first part of the study, the characteristics of the leachate from Ampang landfill, collected before and after the landfill closure was analysed. In general, the characteristics of the Ampang landfill leachate was found to be typical of other landfill leachates in the Klang Valley. The analysis reveals that the Ampang landfill leachate during its active life had high contents of sodium, potassium, chloride and ferum, with concentrations of 687 ppm, 785 ppm, 2500 ppm and 45 ppm respectively. Generally and as expected, the leachate collected before the landfiII closure was found to be more concentrated and contains more …

Assessing Methodologies For Identification Of Significant Impacts In The Iso 14001 Ems (Environmental Management Systems), Ann Wye-Wye Wang

Student Works (2000-2009)

ISO 14001 is a voluntary environmental management system specification standard in the ISO 14000 series. It contains those elements that must be satisfied by an organisation seeking registration or certification to the standard. Identification of significant environmental impacts is one of the requirements as stated in clause 4.3.1 of MS ISO 14001 EMS - specification with guidance for use, and is an important step in the implementation of ISO 14001 standard. A study on the methodologies for identification of significant environmental impacts in the ISO 14001 EMS (Environmental Management Systems) was carried out. Three methods that have been developed are …

Development Of A Physico-Chemical Wastewater Treatment Strategy For A Chemical Plant, T. Alagarajah K. Thavarajah

Student Works (2000-2009)

A study was carried out to determine the physico-chemical treatment of the wastewater collected from a soap and detergent factory in Selangor, Malaysia. The study was initiated by determining the characteristics of the wastewater. Treatability studies involving coagulation and flocculation were determined by the jar test method. The parameters of interest were coagulant dosage, pH, mixing intensity, mixing time and settling time. The coagulants were restricted to alum and ferric sulfate and coagulant aids utilized were polyvinyl alcohol, sodium alginate and polycthylcninimine. An extended evaluation to determine the effect of double chemical treatment was also carried out with the most …

Comparative Performance Of Wastewater Treatment Plants In Three Rubber Glove Manufacturing Plants, Lee Kuan Loh

Student Works (2000-2009)

During the manufacturing of rubber gloves, water is used as wash water at different stages to clean the rubber gloves, thus generating quite a substantial amount of effluent. There are four main sources of effluent. i.e. a) from the glove formers cleaning tank, which collects the acidified water used to clean these formers, b) latex dipping tank, where it collects wash water used to cool the tank during dipping process and the sludge form the tank itself, c) leaching tank, where it collects wash water used to leach out the pollutants from the gloves and lastly d) latex compounding, containing …

Waste Management In Palm-Oleo Sdn. Bhd, Ramesh Ramasamy

Student Works (2000-2009)

Oleochemical industry in Malaysia has been diversifying significantly due to the availability of raw materials (palm oil) and the high demand for downstream products such as fatty acids, fatty alcohols and glycerine. The growth of oleochemical industries is further enhanced by fluctuations io petroleum price and regular animal diseases, which made tallow-based fats unreliable. Environmental awareness is growing rapidly in Malaysia. There is growing realization of the need to balance industrial and economic development with environmental preservation and protection, as well as, with efficient use of energy sources in order to achieve sustainable development. Extensive waste management studies were focused …

Alternative Principal Components Regression Procedures For Dendrohydrologic Reconstructions, Hugo G. Hidalgo, Thomas C. Piechota, John A. Dracup

Civil and Environmental Engineering and Construction Faculty Research

Streamflow reconstruction using tree ring information (dendrohydrology) has traditionally used principal components analysis (PCA) and stepwise regression to form a transfer function. However, PCA has several procedural choices that may result in very different reconstructions. This study assesses the different procedures in PCA-based regression and suggests alternative procedures for selection of variables and principal components. Cross-validation statistics are presented as an alternative for independently testing and identifying the optimal model. The objective is to use these statistics as a measure of the model's performance to find a conceptually acceptable model with a low prediction error and the fewest number of …

Effects Of Ozone/Hydrogen Peroxide Pretreatment On Aerobic Biodegradability Of Nonionic Surfactants And Polypropylene Glycol, Mehmet Kitis, Craig D. Adams, John Kuzhikannil, Glen T. Daigger

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Studies were conducted which used the ozone/hydrogen peroxide (O₃/H₂O₂) advanced oxidation process to pretreat three classes of compounds prior to aerobic biological treatment. The study compounds included ethylene oxide/propylene oxide (EO/PO) block copolymers, polypropylene glycols (PPGs), linear secondary alcoholethoxylates (LSAES), and alkylphenolethoxylates (APEs). After preoxidation with ozone and hydrogen peroxide (added at their stoichiometric ratio), 300 mg/L as COD samples were bioassayed in aerobic batch bioassays with a mixed liquor suspended solids concentration of 1500 mg/L. It was found that unoxidized polypropylated compounds (EO/PO block copolymers and PPGs) and LSAEs tended to be biorecalcitrant, …

A Buffered Advection/Dispersion Lake Water Quality Transport Framework For Modeling Lake Gaston Pipeline Intake Water Withdrawal, Lloyd Ashton Gatling

Civil & Environmental Engineering Theses & Dissertations

Water quality response to reservoir water withdrawal is investigated in Pea Hill Arm of Lake Gaston, a non-tidal reservoir tributary, where the point of water withdrawal is in an upstream tributary and influences the direction of tributary flow causing longitudinal velocity null flow conditions to occur. The study also focuses on control of withdrawal rate and timing to optimize both quality of water remaining in the tributary and quantity of water that can be safely withdrawn.

Research was conducted assuming steady state conditions and later under spatial and temporal variability experienced in the reservoir with main lake pool elevation fluctuations …

Dynamic Fluvial Systems And Gravel Progradation In The Himalayan Foreland, Nicholas Brozovic, Douglas W. Burbank

Daugherty Water for Food Global Institute: Faculty Publications

Although the large-scale stratigraphy of many terrestrial foreland basins is punctuated by major episodes of gravel progradation, the relationships of such facies to hinterland tectonism and climate change are often unclear. Structural reentrants provide windows into older and more proximal parts of the foreland than are usually exposed, and thus provide key insights to earlier phases of foreland evolution. Our magnetostratigraphic studies show that, although the major lithofacies preserved within the Himachal Pradesh structural reentrant in northwestern India resemble Neogene facies in Pakistan, they have a much greater temporal and spatial variability. From 11.5 to 7 Ma, major facies boundaries …

In Situ Treatment Of Chlorinated Ethene-Contaminated Groundwater Using Horizontal Flow Treatment Wells, Derek R. Ferland

Theses and Dissertations

The limitations of conventional containment technologies for groundwater contaminated with chlorinated solvents have motivated development of innovative technologies to achieve national groundwater remediation objectives. One inn9vative technology that is currently under development involves metal reductants or catalysts to chemically destroy the dissolved chlorinated solvent. Models are important tools that can be used to help transition this technology to the field. Model studies can be used to gain understanding about the technology, help determine when the prospective technology might work for a given site, and design full-scale field applications.

Analysis Of The Air Force Iso 14001 Pilot Study Conducted By Dod, Rodney C. Harris

Theses and Dissertations

The Department of Defense (DoD) conducted an ISO 14001 pilot study with the primary goal of determining how ISO 14001 could help DoD organizations reduce risks, improve compliance with environmental regulations, enhance stewardship, contain costs, and meet emerging regulatory requirements. This thesis analyzed the pilot study, specifically looking at the ISO 14001 implementation at three Air Force installations participating in the study. The research objectives were to identify factors that affect implementation of ISO 14001, compare the implementation strategies used by the bases, and develop propositions for Air Force managers to consider when implementing ISO 14001. Interviews of key personnel, …