Civil and Environmental Engineering Commons^™

Color Removal From Pulp Mill Effluent Using Coal Ash Produced From Georgia Power Coal Combustion Plants, Christopher B. Willett

College of Graduate Studies: Theses & Dissertations

Two environmental concerns currently face Georgia: coal fly ash (CFA) waste from coal power plants, and the effluent generated by pulp mills. Pulp mill effluent discolors surface waters into which it is discharged, and has been proven to negatively impact the dissolved oxygen and carbon necessary for aquatic life. The proposed solution is a cost-effective adsorption treatment using an inexpensive but abundantly available waste material: CFA. CFA possesses beneficial properties that allow it to effectively remove contaminants, and is available at significantly reduced cost. The primary research objective was to define treatment parameters that would result in the maximum removal …

Influence Of Spatial Variations Of Railroad Track Stiffness And Material Inclusions On Fatigue Life, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Railroad transportation is very important for economic growth and effective maintenance is one critical factor for its economic sustainability. The high repetitive forces from a moving railcar induce cyclic stresses that lead to rail bending and potential deterioration due to fatigue crack initiation and propagation. Previous research for prediction of fatigue life has been done under the assumptions of a uniform track bed and a homogeneous rail. However the spatial variation of the track stiffness is expected to increase the maximum stresses in the rail and, therefore, accelerate the fatigue process. The research described in this dissertation is focused on …

Micro- And Macro-Scale Modeling Of Filter Aging: Effects Of Particle Poly-Dispersity And Fiber Cross-Sectional Shape, Ahmed M. Saleh

Theses and Dissertations

The goal of this study is to further advance the state of the art in developing self-sufficient methods to predict the performance of an aerosol filter. The simulation methods developed in this study are based on first principles and consequently, they do not rely on empirical correction factors. These simulation methods can be used to predict the instantaneous collection efficiency and pressure drop of a filter under dust-loading conditions. In the current study, 3-D micro- and macroscale CFD models are developed to simulate the service life of flat-sheet and pleated filters. These CFD micro- and macroscale models are also used …

College Of Engineering Senior Design Competition Fall 2014, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Design Of Gan-Based Low-Loss Y-Branch Power Splitter, Retno Wigajatri Purnamaningsih, Irma Saraswati, Nji Raden Poespawati, Elhadj Dogheche

Makara Journal of Technology

We present a Y-branch power splitter design with a multimode section using GaN on Sapphire at telecommunication wavelength. The GaN sample optical properties were also investigated, resulting in a refractive index for the GaN layers nTE=2.289±0.001 and nTM=2.324±0.00. Optimization of the structure parameters for this structure was conducted accurately using BPM methods. The results demonstrated the possibility of realizing a GaN-based Y-branch power splitter for various applications.

Ultra-Wideband Notched Characteristic Fed By Coplanar Waveguide, Rastanto Hadinegoro, Yuli Kurnia Ningsih, Indra Surjati

Makara Journal of Technology

In this paper, a novel Ultra-Wide Band (UWB) notch patch antenna with co-planar waveguide (CPW) fed is presented. This antenna only used one layer and the patch antenna is constructed on the first layer and back to back with CPW fed and bottom part is ground plane. The width notch is used to achieve the UWB characteristic. The results shown that the impedance bandwidth is 1130 MHz (1.662–2.792 GHz) or about 50.7% for VSWR <2.

Analysis Of Vibration Generated By The Rubbing Of Flat Surfaces, Zahrul Fuadi

Makara Journal of Technology

Among the phenomena that occur as a result of contact between two surfaces is friction sound, in which surface roughness is of great importance. In this study, the parameter of contact stiffness is used to explain the frequency characteristic of vibration generated by the rubbing of flat surfaces under a small load. A 3-disk configuration rubbing method was used, which provides a unique characteristic of the system's frequency response function containing specific information about the rubbing vibrations. It is shown that the peak frequency of the rubbing vibration can be explained by using a two-degrees-of-freedom model incorporating the parameter of …

Endoscopic Application Of A Compact Compound-Eye Camera, Keiichiro Kagawa, Shoji Kawahito

Makara Journal of Technology

A multi-functional compound-eye endoscope enabling multi-spectral imaging and variable field-of-view is presented, which is based on a compact compound-eye camera called TOMBO (thin observation module by bound optics). Narrow-band filters attached to some lenses provide snap-shot multi-band images. Fixed and movable mirrors are introduced to control the field of view, which realizes several observation modes such as three-dimensional shape measurement, wide field-of-view, and close-up observation.

Development Of The Soekarno–Hatta International Airport Rail Link Project Using The Value Engineering Method: Creating Value For Money, Mohammed Ali Berawi, Bambang Susantono, Suyono Dikun, Tommy Ilyas, Herawati Zetha Rahman, Abdur Rohim Boy Berawi, Teuku Yuri Zagloel, Perdana Miraj, Jade Sjafrecia Petroceany

Makara Journal of Technology

Soekarno–Hatta Airport is the main gateway for international flights to Greater Jakarta. Its accessibility depends on the inter-city and Sedyatmo toll roads, which causes congestion in peak hours, leading to uncertainty about travel times. The Soekarno–Hatta International Airport Rail Link (SHIARL) is proposed as an alternative mass transportation project, which is expected to provide accessibility and mobility for people and goods to and from the airport. Previously, the project was unattractive to private investors as it was technically and financially unfeasible. Therefore, this research aims to improve the feasibility of the Soekarno-Hatta International Airport Rail Link (SHIARL) by using a …

The Mechanical And Tribology Properties Of Sputtered Titanium Aluminum Nitride Coating On The Tungsten Carbide Insert Tool In The Dry Turning Of Tool Steel, Esmar Budi, Mohd. Razali Bin Muhamad, Md. Nizam Bin Abdul Rahman

Makara Journal of Technology

The effect of the sputtering parameters on the mechanical tribology properties of Titanium Aluminum Nitride coating on the tungsten cabide insert tool in the dry turning of tool steel has been investigated. The coating was deposited using a Direct Current magnetron sputtering system with various substrate biases (-79 to -221 V) and nitrogen flow rates (30 to 72 sccm). The dry turning test was carried out on a Computer Numeric Code machine using an optimum cutting parameter setting. The results show that the lowest flank wear (~0.4 mm) was achieved using a Titanium Aluminum Nitride-coated tool that was deposited at …

Modified Design Of Pin-On-Ring Tribometer For Hip Joint Prostheses Measurement; Case Study On Salat Activity, Muhammad Khafidh, Jamari Jamari, Sulardjaka Sulardjaka, Mohamad Tauviqirrahman, Emile Van Der Heide

Makara Journal of Technology

Total hip replacement (THR) is one of the most successful orthopedic surgical procedures for replacing a broken hip joint. In THR, wear may occur at the articulating surface of the acetabular cup and the femoral head. In Indonesia, the country with the largest Muslim population in the world, most of the inhabitants do salat (praying) every day. THR users are banned from doing salat for fear it will damage the hip joint prostheses. The previous wear calculation methods on the hip joint prostheses use the gravimetric, coordinate measuring machine (CMM), profiler, and geometric method. The disadvantages of the previous methods …

Continuous Production Of Nanotubes And Carbon Clusters By Use Of The Revolver-Injection-Type Arc Jet Producer, Tetsu Mieno, Naoki Matsumoto, Takahashi Tomie, H. Inoue

Makara Journal of Technology

Efficient and continuous production of fullerenes, single-walled carbon nanotubes (SWNTs), and carbon nano-particles has been developed by the JxB arc jet method, where the Lorentz force of magnetic field jets out gaseous carbon particles to the JxB direction. In order to realize continuous mass production of these carbon clusters, the revolverinjection- type arc jet producer (RIT-AJP) has been developed. Production of fullerenes, endohedral metallo-fullerenes, SWNTs, metal-encapsulated carbon nano particles has been examined.

Lateral Load Resistance Of Laminated Veneer Lumber Sengonwooden Joints With Wooden Dowels, Niken Palaeowati, Ali Awaludin, Suprapto Siswosukarto

Makara Journal of Technology

Analytical models for wooden-doweled joints need to be developed. The objective of this research is to determine whether the strength of wooden-doweled joints can be well predicted by equations developed for steel-doweled joints. In this experiment, various connection parameters, such as dowel diameter, species of the wooden dowel, and angle of joints, are studied. The joint specimens are loaded in a quasi-static state with four replications each. A5% offset diameter method is used to determine the lateral load resistance of the tested joints, while the predictions are evaluated by equations given in Indonesian National Standard (SNI) 7973-2013 and the European …

Ole Miss Engineer 2014-2015

Ole Miss Engineer

No abstract provided.

Cal Poly India Project, Derek Babine, Austen Hibler, Alex Hernandez

Mechanical Engineering

This report documents the research, ideation, and development of a solution, implemented by the Cal Poly India Sanitation Team per the request of Mr. Harish Bhutani, to solve the problem of hazardous human waste management in poor villages in India. The sponsor envisioned a universal design that would give each household in those villages access to a private toilet system because the current solution is open defecation in water sources and farming fields. The initial constraints required the project be low cost, not use of electricity or water, have the ability to cater to an 8-10 person household, and be …

Methane Production By A Packed-Bed Anaerobic Digester Fed Dairy Barn Flush Water, Sean Richard Thomson

Master's Theses

Packed-bed digesters are an alternative to covered lagoon digesters for methane production and anaerobic treatment of dilute wastewaters such as dairy barn flush water. The physical media of packed-beds retain biofilms, often allowing increased treatment rates. Previous studies have evaluated several types of media for digestion of dilute wastewaters, but cost and media fouling have setback commercial development. A major operational cost has been effluent recirculation pumping.

In the present effort, a novel approach to anaerobic digestion of flush dairy water was developed at pilot-scale: broken walnut shells were used as a low-cost packed-bed medium and effluent recirculation was replaced …

High Voltage Rear Electric Drivetrain Design For A Parallelthrough-The-Road Plug-In Hybrid Electric Vehicle, Adam Garrett Fogarty

Open Access Theses

Purdue University was selected as one of 15 universities to participate in a three year Advanced Vehicle Technology Competition (AVTC) called EcoCar2: Plugging Into the Future. The vehicle built by the Purdue team was a Parallel-Through-The-Road Plug-in Hybrid Electric Vehicle (PTTR PHEV). The vehicle utilized a B20 diesel powertrain to power the front wheels, as well as a custom electric drivetrain to power the rear wheels. Using this vehicle during the final year of the competition, the team was successful in placing 4th overall as well as 2nd in the category of Well-To-Wheel (WTW) Greenhouse Gas Emissions. A stock 2013 …

Agricultural Industry Advanced Vehicle Technology: Benchmark Study For Reduction In Petroleum Use, Roger M. Hoy, Rodney Rohrer, Adam Liska, Joe D. Luck, Loren Isom, Deepak R. Keshwani

Adam Liska Papers

Diesel use on farms in the United States has remained relatively constant since 1985, decreasing slightly in 2009, which may be attributed to price increases and the economic recession. During this time, the United States’ harvested area also has remained relatively constant at roughly 300 million acres. In 2010, farm diesel use was 5.4% of the total United States diesel use. Crops accounting for an estimated 65% of United States farm diesel use include corn, soybean, wheat, hay, and alfalfa, respectively, based on harvested crop area and a recent analysis of estimated fuel use by crop. Diesel use in these …

Adjustable Resonance Frequency Of Rf-Mems Capacitor By Using Comb- Drive Actuators: A Design Approaches, Agus Santoso Tamsir, Sandy Tannu Wijaya, Dato’ Burhanuddin Yeop Majlis

Makara Journal of Technology

The needs of smaller size RF varactor is a must today, and MEMS comes to be the potential one. In this paper we proposed an adjustable resonance RF-MEMS varactor by using comb-drive actuators placing in each side of the square movable plate. In our preliminary simulation, we found that the device can work properly but some constraints comes such as the dominancies of harmonic resonance frequencies that influences into the nominal capacitances. Therefore for the next step of development we have to find out the window of the structural dimension for a certain spans and a certain operating frequencies.

Make Or Buy Analysis Model Based On Tolerance Design To Minimize Manufacturing Cost And Quality Loss, Cucuk Nur Rosyidi, Reza Rizkichani Akbar, Wakhid Ahmad Jauhari

Makara Journal of Technology

In a manufacturing company, manufacturing costs, or component prices, and tolerance will affect the price and the quality of a product. Companies must produce high-quality products with low manufacturing costs in order to keep their products competitive in the market; however, it is difficult to produce a high-quality product with a low manufacturing cost. Companies have difficulties in determining the components to be produced using their own manufacturing facilities (make) or outsourced to their suppliers (buy). Hence, a make or buy analysis is needed to minimize the manufacturing costs and quality loss and to determine the optimum alternative regarding make …

Observation Of Tunneling Effects In Lateral Nanowire Pn Junctions, Sri Purwiyanti, Arief Udhiarto, Daniel Moraru, Takeshi Mizuno, Djoko Hartanto, Michiharu Tabe

Makara Journal of Technology

As electronic device dimensions are continuously reduced, applied bias conditions significantly change and the transport mechanisms must be reconsidered. Tunneling devices are promising for scaled-down electronics because of expected high-speed operation and relatively low bias. In this work, we investigated the tunneling features in silicon-oninsulator lateral nanowire pn junction and pin junction devices. By controlling the substrate voltage, tunneling features can be observed in the electrical characteristics. We found that the minimum substrate voltage required for tunneling to occur in pn junctions is higher as compared with pin junctions. The main cause of these effects relies in the difference between …

Argon Ion Irradiation Effect On The Magnetic Properties Of Fe-Al2o3 Nano Granular Film, Setyo Purwanto, Isao Sakamoto

Makara Journal of Technology

We studied the effect of Argon (Ar) ion irradiation on Fe-Al2O3 nanogranular thin film. X-ray diffraction (XRD) patterns show that the ion dose might promote the growth of the Fe2O3 phase from an amorphous phase to a crystalline phase. The magnetic and magnetoresistance properties were investigated using a vibrating sample magnetometer (VSM) and a four point probe (FPP). The results suggest that percolation concentration occurred at the 0.55 Fe volume fraction and with a maximum magnetoresistance (MR) ratio of 3%. The present MR ratio was lower than that of previous results, which might be related to the existence of the …

Digestibility Of Betung Bamboo Fiber Following Fungal Pretreatment, Widya Fatriasari, Wasrin Syafii, Nyoman J. Wistara, Khaswar Syamsu, Bambang Prasetya

Makara Journal of Technology

This research evaluated the effect of fungal pretreatment of betung bamboo fibers and enzymatic- and microwaveassisted hydrolysis on the reducing sugar yield. The enzymatic hydrolysis of the pretreated biomass was carried out with cellulase and 10 and 20 FPU/g of substrate in a shaking incubator at 50 °C and 150 rpm for 48 h. The sulfuric acid concentration used in the microwave-assisted acid hydrolysis was 1.0, 2.5, and 5%, either with or without the addition of activated carbon. Microwave irradiation (330 Watt) was applied for 5–12.5 min. The yield of reducing sugar was better with the microwave-assisted acid hydrolysis, and …

Electron Emission Characteristics Of Multi-Gated Field Emitters, Hidenori Mimura, Yoichiro Neo, Toru Aoki, Tomoya Yoshida, Masayoshi Nagao

Makara Journal of Technology

We have developed a multi-gated field emitter (FE) such as a quadruple-gated FE with a three-stacked electrode lens and a quintuple-gated FE with a four-stacked electrode lens. Both the FEs can focus the electron beam. However, the quintuple-gated FE has a stronger electron convergence than the quadruple-gated FE, and a beam crossover is clearly observed for the quintuple-gated FE.

Properties Of Lignin From Oil Palm Empty Fruit Bunch And Its Application For Plywood Adhesive, Lucky Risanto, Euis Hermiati, Yanni Sudiyani

Makara Journal of Technology

Lignin from lignocellulosic biomass is a potential biopolymer for wood adhesive. The aims of this study were to characterize lignin isolated from the black liquor of oil palm empty fruit bunch fiber pretreated with steam explosion in alkaline conditions and to examine the bond quality of aqueous polymer isocyanate (API) adhesive prepared from lignin, natural rubber latex (NRL), and polyvinyl alcohol (PVA) as base polymers with isocyanate crosslinkers. Lignin was precipitated from the black liquor by adding hydrochloric acid; then the precipitate was separated by filtration, thoroughly washed with water up to pH 2 and pH 5, and dried. The …

The Gaussian Orthogonal Laplacianfaces Modelling In Feature Space For Facial Image Recognition, Arif Muntasa

Makara Journal of Technology

Dimensionality reduction based on appearance has been interesting issue on the face image research fields. Eigenface and Fisherface are linear techniques based on full spectral features, for both Eigenface and Fisherface produce global manifold structure. Inability of them in yielding local manifold structure have been solved by Laplacianfaces and further improved by Orthogonal Laplacianfaces, so it can yield orthogonal feature vectors. However, they have also a weakness, when training set samples have non-linear distribution. To overcome this weakness, feature extraction through data mapping from input to feature space using Gaussian kernel function is proposed. To avoid singularity, the Eigenface decomposition …

Series-Interconnected Plastic Dye-Sensitized Solar Cells Prepared By Low- Temperature Binder-Free Titania Paste, Erlyta Septa Rosa, Lia Muliani, Shobih Shobih, Jojo Hidayat, Brian Yuliarto

Makara Journal of Technology

The aim of this research is to study dye-sensitized solar cells (DSSC). This was implemented on a flexible polyethylene terephthalate (PET) substrate using a mixture of transparent and scattered mesoporous anatase-titania as the electron transport layer for the photoelectrode. This mixture of anatase titania performed a dual function of light scattering and efficient dye absorption. In this study, a porous nano-TiO2 film was prepared on indium tin oxide (ITO) coated polyethylene terephthalate (PET) by using a binder-free titania paste; on it, a DSSC was fabricated. The paste which contained a mixture of TiO2 nanoparticles, acid chloride, and ethanol was printed …

Increased Span Length For The Mgs Long-Span Guardrail System, Nicholas A. Weiland

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Long-span guardrail systems have been recognized as an effective means of shielding low-fill culverts while minimizing construction efforts and limiting culvert damage and repair. The current MGS long-span design provided the capability to span unsupported lengths up to 25 ft (7.6 m) without the use of nested guardrail. The excellent performance of the MGS long-span system in full-scale crash tests suggested that longer span lengths may be possible with the current design.

A detailed analysis of the MGS long-span guardrail system was performed using the finite element software program LS-DYNA^®. It was shown that the MGS long-span design …

Development, Numerical Demonstration And Experimental Verification Of A Method For Model Updating Of Boundary Conditions, Christian Eduardo Silva Salazar

Open Access Theses

The study of vibrations in beams has been largely addressed by authors and researchers. However, relatively few researchers have considered the case of unknown boundary conditions, as usually it is reasonable to assume the classical cases such as simply supported, clamped or free. Indeed, there are a wide variety of boundary-condition configurations, each one representing a whole different problem with its own modal characteristics. ^ A method for updating experimental beam models to specifically address the issue of unknown boundary conditions is proposed. This methodology takes advantage of vector comparison techniques such as the modal assurance criterion and the dot …

Analysis Of Different Techniques For Improving Performance Of Flat Plate Solar Collectors For Fruits Drying, Godfrey Mbabaye

Tanzania Journal of Engineering and Technology (TJET)

Fruits drying had become a broader technology in fruits and vegetables value addition. The technology is reported to be a promising way of drying without incurring higher cost but its adaptation has not been feasible in rural areas. Solar dryers have been developed but its poor performance limits its applicability. In this study, several techniques for modifications of traditional solar collector were addressed. It was observed that, varying collector designs in different techniques, a range of collector performances can be archived. The research shows that, collector efficiency can be improved by 9.6% when employing double duct counter flow compared to …