Civil and Environmental Engineering Commons^™

Mechanical Behavior Of Grouted Sands, Ryan C. Ortiz

Theses and Dissertations--Civil Engineering

Grouting techniques have been in used for many years, but several new grout materials have surfaced in recent decades that have re-defined the boundaries of the limitations of grouting programs. Typically these applications are used for seepage control in earthen impoundments, but strength of these earthen impoundments should be considered where there is potential for movement in the grouted soil mass. This study investigated initial conditions that could affect grout application effectiveness. The initial conditions in question were soil grain size and in situ moisture content. Two grouts were used, ultrafine and acrylate, and variations in pure grout properties were …

Deformation-Based Excavation Support System Design Method, Sekyi K. Intsiful

Theses and Dissertations--Civil Engineering

Development in urban areas around the world has steadily increased in recent years. This rapid development has not been matched by the ever decreasing open space commonly associated with urban centers. Vertical construction, thus, lends itself a very useful solution to this problem. Deep excavation is often required for urban construction. Unfortunately, the ground movements associated with deep excavation can result in damage to adjacent buildings. Thus, it is critically important to accurately predict the damage potential of nearby deep excavations and designing adequate support systems.

A new design method is proposed, as an attempt, to address the problem. The …

Prediction Of Strength And Shear Modulus Of Compacted Clays Within An Unsaturated Critical State Framework, Corrie Walton-Macaulay

Theses and Dissertations--Civil Engineering

The objective of this research study is to determine whether the soil stiffness, from which the small-strain shear modulus is determined, can be used to predict the shearing resistance of compacted clay soil, which are invariably under conditions of partial saturation. The research program developed for this objective included three major soil testing programs of matric suction, shear modulus, and strength.

A method to estimate matric suction of field compacted clay soil was presented and it is based on the quantified effect of change in initial void ratio on the soil water characteristic behaviors. With the use of a non-nuclear …

Simulating Energy Efficient Control Of Multiple-Compressor Compressed Air Systems, Sean Murphy, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

In many industrial facilities it is common for more than one air compressor to be operating simultaneously to meet the compressed air demand. The individual compressor set-points and how these compressors interact and respond to the facility demand have a significant impact on the compressed air system total power consumption and efficiency. In the past, compressors were staged by cascading the pressure band of each compressor in the system. Modern automatic sequencers now allow more intelligent and efficient staging of air compressors.

AirSim, a compressed air simulation tool, is now able to simulate multiple-compressor systems with pressure band and automatic …

Determining Rockfall Volumes In Three Sites Along Habs Mountain Road In Southwestern Saudi Arabia, Using Lidar Technology, Abdullah Ayed Al-Otaibi

Masters Theses

"The rugged elevated topography is a characteristic feature of the western and southwestern regions of Saudi Arabia. Few arterial roads connect the scattered villages of these regions to major cities, such as Habs Road in Jazan region. Rock fall poses a serious hazard to people, property and animals along the rock cuts of this road. Although no traditional Rockfall studies have previously been applied to this road, accessibility and rock formation shape and structure variability influenced the choice of using Terrestrial Light Detection And Ranging (LiDAR) technology to calculate the volume of rockfall at selected sites along this road.

Software …

Evaluating Methods Of Field-Based 3d Visualization And Their Application To Mapping Metamorphic Terranes: An Example From The Panamint Mountains, California, Jade Ashley Brush

Open Access Theses & Dissertations

Field geology has traditionally relied on 2D, paper-based workflows, but digital mapping techniques are rapidly replacing these outdated methods because they allow for more efficient and accurate mapping. This research applies digital mapping techniques and two terrestrially-based 3D visualization technologies, photogrammetry and Light Detection and Ranging (LiDAR), to the study of metamorphic terranes in the Panamint Mountains, California. This study reports on the spatial accuracy of TINs (triangulated irregular networks) generated from both photogrammetry and ground-based LiDAR using a terrestrial laser scanner (TLS) and discusses how spatial accuracy can be increased. Two levels of comparison were used to test spatial …

Restricted Salt Diffusion In A Geosynthetic Clay Liner, Michael A. Malusis, Jong Beom Kang, Charles D. Shackelford

Faculty Journal Articles

No abstract provided.

Mechanical Characteristics Of Organically Modified Fly Ash-Kaolinite Mixtures, Xin Kang

Doctoral Dissertations

"Fly ash is a hazardous waste material to the environment. Beneficial reuse of fly ash, however, brings economic and environmental benefits, i.e., decreases the cost of disposal, reduces greenhouse gas emission, and improves mechanical properties of construction materials. Due to the lack of pozzolanic properties, the reuse rate of Class F fly ash in geotechnical engineering is relatively low (ACAA 2013). In order to promote the effectiveness and sustainability of high volume reuse of class F fly ash in geotechnical engineering, biopolymers (Chitosan, and Xanthan gum) and synthetic polymers (Polyethylene Oxide, PEO) were used instead of the traditional stabilizers to …

Agenda For Second Meeting Of The Forum For Promotion Of Soil Dynamics In India, Shamsher Prakash

Forum for Promotion of Soil Dynamics in India

No abstract provided.

Membership Of Forum For Promotion Of Soil Dynamics In India, Shamsher Prakash

Forum for Promotion of Soil Dynamics in India

No abstract provided.

Honor Stalwarts, Shamsher Prakash

Forum for Promotion of Soil Dynamics in India

No abstract provided.

Center Of Excellence In Geotechnical Earthquake Engineering And Soil Dynamics At Iit Roorkee, Shamsher Prakash

Forum for Promotion of Soil Dynamics in India

No abstract provided.

Soil Dynamics Course In Curriculum, Deepankar Choudhury

Forum for Promotion of Soil Dynamics in India

No abstract provided.

Reliability-Based Design And Acceptance Protocol For Driven Piles, Joseph Jabo

Graduate Theses and Dissertations

The current use of the Arkansas Standard Specifications for Highway Construction Manuals (2003, 2014) for driven pile foundations faces various limitations which result in designs of questionable reliability. These specifications are based on the Allowable Stress Design method (ASD), cover a wide range of uncertainties, do not take into account pile and soil types, and were developed for general use. To overcome these challenges it is deemed necessary to develop a new design and acceptance protocol for driven piles. This new protocol incorporates locally calibrated RLFD resistance factors for accounting for local design and construction experiences and practices, as well …

Calibration Of Resistance Factors For Driven Piles Using Static And Dynamic Tests, Deshinka A. Bostwick

Graduate Theses and Dissertations

The field of geotechnical engineering has evolved from Allowable Stress Design (ASD) to Load Factor and Resistance Design (LRFD) which has led to a need to quantify the measures of uncertainty and the level of reliability associated with a project. The measures of uncertainty are quantified by load and resistance factors, while the level of reliability is driven by the amount of risk an owner is willing to take and is quantified by the reliability index. The load factors are defined through structural design codes, but the resistance factors have uncertainties that can be mitigated through reliability based design. The …

Effect Of Caliche On The Behavior Of Drilled Shafts, Rouzbeh Afsharhasani

UNLV Theses, Dissertations, Professional Papers, and Capstones

The current design methodology for a drilled shaft foundation in cohesionless soil is primarily based on ultimate skin friction values of drilled shafts. In order to obtain these values for each soil type, load tests such as Osterberg test are designed and performed. The Osterberg test layout is designed to estimate the capacity of drilled shaft by applying an upward load during the test and then calculating the downward capacity assuming the upward and downward capacity are the same. This method is appropriate for soils not containing caliche layers because caliche layers bond to the shaft and prevent skin friction …

Modeling Pavement Distress Rates Within U.S. Air Force Airfields, Lauren Sahagun

UNLV Theses, Dissertations, Professional Papers, and Capstones

Through the review of Pavement Condition Index (PCI) surveys completed at Air Force installations scattered across the continental United States, pavement engineers at the Air Force Civil Engineer Center propose that the predominant factor contributing to pavement distress development is climate. They suggest that within each pavement distress type (i.e. alligator cracking, rutting, spalling, etc.) a geographic pattern exists that is strongly correlated to the conventional climate zones within the US. Knowledge of these geographic patterns would equip pavement engineers and asset managers with a powerful tool to develop purposeful maintenance strategies specific to each distress type.

The following approach …

Estimating Field At-Rest Lateral Stress Coefficient And Liquefaction Resistance Of Aged Sands, Md Hossian

All Dissertations

Published results of laboratory tests to evaluate the influence of the at-rest lateral stress coefficient (K0) and the overconsoildation ratio (OCR) on liquefaction resistance of sands are reviewed in this dissertation. It is found that significant increase in liquefaction resistance can occur with high K0 and/or high OCR. A unique relationship between liquefaction resistance of isotropic and anisotropic normally consolidated sands exists based on the published laboratory data. Relationships between liquefaction resistance of overconsolidated sands and normally consolidated sands also have been shown in previous laboratory studies. Based on the previous studies, expressions for K0 and OCR correction factors (KK0 …

Field-Obtained Soil Water Characteristic Curves And Hydraulic Conductivity Functions, Elvis Ishimwe

Graduate Theses and Dissertations

A compacted clay liner (test pad) was constructed and instrumented with volumetric water content and soil matric potential sensors to determine soil water characteristic curves (SWCC) and hydraulic conductivity (k) functions. Specifically, the compacted clay liner was subjected to an infiltration cycle during a sealed double ring infiltrometer (SDRI) test followed by a drying cycle. After the drying cycle, Shelby tube samples were collected from the compacted clay liner and flexible wall permeability (FWP) tests were conducted on sub-samples to determine the saturated hydraulic conductivity. Moreover, two computer programs (RETC and UNSAT-H) were utilized to model the SWCCs and k-functions …

Evaluation Of Volatile And Semi-Volatile Organic Compounds Potentially Associated With The Gas Shale Fracturing Process In The Fayetteville And Marcellus Shale, Karl Albert Oetjen

Theses - ALL

With the recent growth of the natural gas industry coupled with technological advancements, gas shale fracturing has become an effective and highly profitable method for natural gas production. Unlike conventional natural gas extraction which may require vertical fracturing, gas shale fracturing relies on a method known as horizontal fracturing to remove gas trapped within the impermeable facies. Compared to vertical fracturing, horizontal fracturing requires larger amounts of fluids to be injected downhole under high pressure. These fracturing fluids can contain high concentrations of petroleum hydrocarbons with known adverse health effects. Due to the large volumes used, the potential for groundwater …

Development And Use Of Moisture-Suction Relationships For Geosynthetic Clay Liners, Jacob Law Risken

Master's Theses

A laboratory test program was conducted to determine the moisture-suction relationships of geosynthetic clay liners (GCLs). Moisture-suction relationships were determined by combining suction data from pressure plate tests, contact filter paper tests, and relative humidity tests, then fitting water retention curves (WRCs) to the data. WRCs were determined for wetting processes and drying processes in terms of gravimetric moisture content and volumetric moisture content.

The effects of GCL type, hydration solution, wet-dry cycles, and temperature on the moisture-suction relationships were analyzed. The three GCLs of the test program consisted of configurations of woven and nonwoven geotextiles reinforced with needlepunched fibers. …

Thermal Numerical Analysis Of Vertical Heat Extraction Systems In Landfills, Michael Thomas Onnen

Master's Theses

An investigation was conducted to determine the response of landfills to the operation of a vertical ground source heat pump (i.e., heat extraction system, HES). Elevated landfill temperatures, reported various researchers, impact the engineering performance of landfill systems. A numerical model was developed to analyze the influence of vertical HES operation on landfills as a function of climate and operational conditions.

A 1-D model of the vertical profile of a landfill was developed to approximate fluid temperatures in the HES. A 2-D model was then analyzed over a 40 year time period using the approximate fluid temperatures to determine the …

Characterization Of Dredged Sediment Used In Coastal Restoration And Marsh Creation Projects, Gregory A. Mattson Ii

LSU New Orleans Theses and Dissertations

To minimize coastal land loss and create new land, dredged sediment has been in use in coastal Louisiana during the last several years. Engineering properties and material characteristics of dredged material are input parameters in several mathematical models used to predict the long-term hydrodynamic behavior of the coast. Therefore, proper characterization of the dredged material is of utmost importance in the correct design of coastal restoration and land creation projects. The sedimentation characteristics of the dredged material, among other factors, depends on the (a) grain size distribution of the dredged material, (b) salinity (fresh, brackish, or saltwater environment) of the …

Finite Difference Modeling Of Surface-~Wave Scattering For Shallow Cavity Detection, Heston Travis Norcott

UNLV Theses, Dissertations, Professional Papers, and Capstones

Data collection and analysis of scattering of Rayleigh-type surface waves are investigated for locating shallowly buried cavities. Surface-based seismic experiments conducted by others at the University of Nevada, Las Vegas (UNLV) Engineering Geophysics Test Site (EGTS) demonstrate scattering of Rayleigh waves caused by buried empty barrels (essentially air-filled cavities). The interpretation of the data is complicated by factors such as the presence of a high-velocity geologic layer just below the cavity.

This research uses a finite-difference seismic wave propagation code to compute time histories for a model that represents the Engineering Geophysics Test Site. By adding cavities to a background …

Rheological Properties Of Laponite And Chemically Modified Laponite Suspensions, Meng Shen

Open Access Theses

This research investigates the rheological properties of concentrated laponite RD suspensions modified through the addition of laponite RDS and sodium pyrophosphate (SPP). The work is aimed at establishing the possible suitability of these materials for treating liquefaction susceptible sands. This application requires that a laponite suspension initially exhibits liquid like behavior and low viscosity that allow its delivery into the pore space of a sand, but that over time the suspension develop a gel structure with solid like behavior that can serve to restrict sand particle mobility during earthquake shaking.

The experimental program made use of a Physica MCR 301 …

Small Strain Stiffness Of A Carbonatic Fine Grained Soil, Sulaiman Dawood

Open Access Theses

The work presented in this thesis is part of a broad effort aimed at the characterization of the engineering properties, microstructure and mineralogy of soft fine-grained carbonatic soil deposit in Southwestern Indiana (Daviess Co.). The specific focus of this thesis is the characterization, through both field and laboratory measurements, of the small strain behavior of this soil, commonly referred to as a "marl."

Index tests indicate that the 3.5 m marl layer present at the site is characterized by two soil types alternating in small sublayers: a high plasticity silt (soil M) with wn ∼60% and CaCO3 ∼60%, mostly in …

Drilled Shaft Design & Construction-Integrity Testing Issues, Mir A. Zaheer, David Latka

Purdue Road School

This presentation will provide an overview of the design and construction of drilled shafts in Indiana, including construction monitoring issue, discussion of CSL, PIT and TIP testing, and comparisons with cores taken.

Soil-Bentonite Slurry Trench Cutoff Wall Proposal, Jeffrey C. Evans, Michael A. Malusis, Robert W. Jacob

NSF Soil-Bentonite Slurry Trench Cutoff Wall Documents

This is the proposal to the National Science Foundation for a soil-bentonite slurry trench cutoff wall. The proposal includes a project summary, description of the project, and the resources implemented on the project.

Membrane Efficiency Of A Dense Prehydrated Gcl, Michael A. Malusis, Akmal Daniyarov

Other Faculty Research and Publications

No abstract provided.

Characterization Of Dynamic Structures Using Parametric And Non-Parametric System Identification Methods, Ayad Al Rumaithi

Electronic Theses and Dissertations

The effects of soil-foundation-structure (SFS) interaction and extreme loading on structural behaviors are important issues in structural dynamics. System identification is an important technique to characterize linear and nonlinear dynamic structures. The identification methods are usually classified into the parametric and non-parametric approaches based on how to model dynamic systems. The objective of this study is to characterize the dynamic behaviors of two realistic civil engineering structures in SFS configuration and subjected to impact loading by comparing different parametric and non-parametric identification results. First, SFS building models were studied to investigate the effects of the foundation types on the structural …