Civil and Environmental Engineering Commons^™

Determination Of Safe Ballasts For Anchoring Event Tents By Finite Element Analysis, Sandeep Manoharan

All Theses

Event tents are large structures made of fabric covers attached to a structural frame and poles. Every year, many temporarily installed tents are subjected to large wind conditions that lead to sliding or lift of the frame due to improper anchoring to the ground. When ballasted, as opposed to anchored using stakes that penetrate the ground, non-certified tents are generally installed without proper analysis of sufficient ballast weights, which results into tent movements and lack of safety. The objective of this thesis is to determine load factors for non-certified tents affected by high wind loads. The load requirements (load factors) …

Coupling K-12 Music Education With Science, Technology, Engineering And Math (Stem) Curricula: Implementation Of A Stemusic Outreach Program, Mallory Maestri

Civil Engineering Undergraduate Honors Theses

Many studies have investigated the effects of music on evoking human emotions and diverse types of brain responses. One study by Juslin and Vastfjall indicates that hearing music can stimulate brain stem reflexes, create emotional contagion, recall episodic memories and provoke visual imagery. Due to the influence music has on human brain waves, researchers have been studying the effect of music on enhancing the spatial abilities of young students. Science, Technology, Engineering and Math (STEM) professions rely heavily on spatial skills. Research on the connection of music with spatial skills proposes that when the brain processes rhythm a “mental rotation” …

Dynamic Mechanical Properties And Microstructure Of Graphene Oxide Nanosheets Reinforced Cement Composites, Wujian Long, Jingjie Wei, Hongyan Ma, Feng Xing

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents an experimental investigation on the effect of uniformly dispersed graphene oxide (GO) nanosheets on dynamic mechanical properties of cement based composites prepared with recycled fine aggregate (RFA). Three different amounts of GO, 0.05%, 0.10%, and 0.20% in mass of cement, were used in the experiments. The visual inspections of GO nanosheets were also carried out after ultrasonication by transmission electron microscope (TEM) atomic force microscope (AFM), and Raman to characterize the dispersion effect of graphite oxide. Dynamic mechanical analyzer test showed that the maximum increased amount of loss factor and storage modulus, energy absorption was 125%, 53%, …

Construction Effects On The Side Shear Of Drilled Shafts, Lucas Caliari De Lima

USF Tampa Graduate Theses and Dissertations

Design methods for side shear of drilled shafts, including the resistance factors that should be applied, do not account for any specific construction procedure. Instead, design often relies on analysis of case studies which include all construction methods used in each geomaterial type (e.g. clays, sands and rocks), or on parametric analysis. Nonetheless, literature suggests that different construction procedures result in varying side shear.

This research investigated 2 types of construction: (1) slurry stabilization in sandy soils using bentonite and polymer products that are commonly used on the field, with exposure times from near 0h to 96h, and (2) temporary …

Bridge Build, Andrew Little

Student Scholarship

Bridge build design that includes not only a building process, but a research paper to make the best build possible as well.

Bond Of Steel Reinforcement With Microwave Cured Concrete Repair Mortars, P. S. Mangat, Shahriar Abubakri, Konstantinos Grigoriadis

Henry M. Rowan College of Engineering Departmental Research

This paper investigates the effect of microwave curing on the bond strength of steel reinforcement in concrete repair. Pull-out tests on plain mild steel reinforcement bars embedded in four repair materials in 100 mm cube specimens were performed to determine the interfacial bond strength. The porosity and pore structure of the matrix at the steel interface, which influence the bond strength, were also determined. Test results show that microwave curing significantly reduces the bond strength of plain steel reinforcement. The reduction relative to normally cured (20 °C, 60% RH) specimens is between 21 and 40% with low density repair materials …

Ireland’S Bim Macro Adoption Study: Establishing Ireland’S Bim Maturity, Barry Mcauley, Alan Hore, Roger West, Mohamad Kassem, Shiyao Kuang

Conference papers

Since 2016 the BIM Innovation Capability Programme (BICP) has captured the capability of the Irish Construction Industry’s and the Higher Education Institutes’ (HEIs) response to the increased requirement for BIM on Irish construction and engineering projects. One of the primary responsibilities of the BICP research team is to collate data to assist the National BIM Council of Ireland in the formulation of a National BIM Roadmap. To assist the Council with this task the BICP research team applied five macro BIM maturity conceptual models to assess Ireland’s BIM maturity. The results from the models were further utilised to develop a …

Stewardship Of International Bim Programmes: Lessons For Ireland, Barry Mcauley, Alan Hore, Roger West, Shiyao Kuang

Conference papers

The support by central government of national Building Information Modelling (BIM) programmes is common throughout the developed world today. To further understand how the different international governments have supported their BIM programmes the BIM Innovation Capability Programme (BICP) research team in Ireland recently completed a comprehensive Global BIM Study to help inform the National BIM Council (NBC) of Ireland in developing a Roadmap to Digital Transition for Ireland’s Construction Sector. This paper details the findings of a more concentrated investigation on a selection of jurisdictions on how particular international BIM programmes are orgainsed, managed and the level of governmental support …

Dns And Les Of Scalar Transfer Across An Air-Water Interface During Inception And Growth Of Langmuir Circulation, Amine Hafsi

USF Tampa Graduate Theses and Dissertations

Direct numerical simulations (DNS) of an initially quiescent coupled air-water interface driven by an air flow with free stream speed of 5 m/s have been conducted. The DNS solves a scalar advection-diffusion equation for dissolved gas (or scalar) concentration in order to determine the impact of the water-side turbulence on scalar (mass) transfer from the air side to the water side and subsequent vertical transport in the water column. Two simulations are compared: one with a freely deforming interface and a second one with a flat interface. In the first simulation, the deforming interface evolves in the form of gravity-capillary …

Field Investigation And Performance Evaluation Of Interface Bonding Between Pavement Layers, Ramendra N. Das

LSU Master's Theses

Proper bonding between pavement layers is essential to provide a monolithic pavement structure that allows distribution of loading over a larger area. Inadequate interface bonding may cause debonding or shear failure at the interface due to the accumulation of concentrated tensile stresses at the bottom of the overlay. Tack coat, a light application of asphaltic cement emulsion is applied on the existing surface to create a strong adhesive bond between pavement layers. The objectives of this study are to investigate the effects of various factors affecting bond strength between hot-mix asphalt (HMA) overlay and underlying pavement layers in the field. …

Development Of Artificial Intelligence Approach To Nowcasting And Forecasting Oyster Norovirus Outbreaks Along The U.S. Gulf Coast, Shima Shamkhali Chenar

LSU Doctoral Dissertations

Oyster norovirus outbreaks pose increasing risks to human health and seafood industry worldwide. This study presents an Artificial Intelligence (AI)-based approach to identifying the primary cause of oyster norovirus outbreaks, nowcasting and forecasting the growing risk of oyster norovirus outbreaks in coastal waters. AI models were developed using Artificial Neural Networks (ANNs) and Genetic Programming (GP) methods and time series of epidemiological and environmental data. Input variable selection techniques, including Random Forests (RF) and Forwards Binary Logistic Regression (FBLR), were used to identify the significant model input variables among six independent environmental predictors including water temperature, solar radiation, gage height, …

An Enhanced Bridge Weigh-In-Motion Methodology And A Bayesian Framework For Predicting Extreme Traffic Load Effects Of Bridges, Yang Yu

LSU Doctoral Dissertations

In the past few decades, the rapid growth of traffic volume and weight, and the aging of transportation infrastructures have raised serious concerns over transportation safety. Under these circumstances, vehicle overweight enforcement and bridge condition assessment through structural health monitoring (SHM) have become critical to the protection of the safety of the public and transportation infrastructures. The main objectives of this dissertation are to: (1) develop an enhanced bridge weigh-in-motion (BWIM) methodology that can be integrated into the SHM system for overweight enforcement and monitoring traffic loading; (2) present a Bayesian framework to predict the extreme traffic load effects (LEs) …

An Experimental Comparison Between Fine Aggregate And Quarry Fines Based On Mortar Block Strength, Karthik Boregowda

Theses and Dissertations

The strength properties of mortar mainly depend on the materials used for casting. Each material has its own importance for cement mortar strength. In this research, quarry fines, a waste by-product, replaced a portion of fine aggregate in mortar. This research focuses on compressive strength of cement mortar using American Society for Testing and Materials standards. The specimens were cast in standard 2”x 2” inch molds. The compressive strength of blocks with replacement of fine aggregate by quarry fines at 15%, 25%, 30%, and 50% was tested at 7, 14 and 28 days of curing. The results were compared with …

Numerical Evaluation Of The Lateral Behavior Of Vertical And Battered Pile Group Foundations Using 3-D Finite Element Modeling, Ahmad Souri

LSU Doctoral Dissertations

The design of pile foundations to resist lateral loads is essential in offshore structures and bridge foundations. The lateral behavior of piles has been studied in the past by experimental investigations coupled with analytical and numerical methods. The problem is complex due to the nonlinearities from soil behavior, gap formation, and pile-soil-pile interaction in pile groups (or the group effect). In this work, the finite element (FE) modeling was used to study the lateral behavior of pile groups. The FE method is robust and allows incorporating the necessary aspects for studying the behavior of pile groups. The nonlinear material behavior …

Analysis Of Distresses In Asphalt Pavement Transitions On Bridge Approaches And Departures, Manvitha Rajalingola

USF Tampa Graduate Theses and Dissertations

Some highway agencies in the United States are experiencing frequent distresses in asphalt pavements on bridge approaches/departures. Commonly observed distresses include alligator cracking and rutting, which reduce roadway smoothness and safety. To lessen the distresses in pavements it is needed to investigate the extent and root causes of the problem. Based on Florida highway conditions, this research study mainly focused on1. Literature review and identification of the extent of the problem; 2. Collection of relevant pavement condition data and descriptive analysis; 3. Development of statistical models to determine factors influencing the distresses in asphalt pavements on bridge approaches/departures. To the …

Modelling Tree Contribution In Susceptibility Analysis Of Shallow Llandslides, Roberto José Marín Sánchez, Juan Pablo Osorio

Articles

In this paper an assessment of shallow landslides susceptibility in a tropical and mountainous terrain is made. A method that allows to model slope stability over large areas is used. Tree contribution is quantified by means of three parameters: rainfall interception, root reinforcement and tree surcharge. A rainfall interception model is used to determine the rain available for infiltration and its temporal distribution during the simulation. The hydrological models included in TRIGRS are described, which allows to determine the pore water pressure depending on the initial conditions. This pore water pressure is used in the revised infinite slope stability model, …

Mass-Balance Assimilative Capacity Model Of Inniscarra Reservoir, Zeinab Bedri, Ahmed Nasr, Sean Crowley

Conference papers

Wastewater arising from the Coachford agglomeration is treated at the existing Coachford Waste Water Treatment Plant (WWTP). This wastewater treatment facility has a primary treatment only with a design capacity of 450 population equivalent (PE) and it discharges the effluent into the Inniscarra Reservoir. The discharge from Coachford WWTP has been identified by the Lower Lee - Owenboy Water Management Unit Action Plan (WMUAP) as a point source pressure on the waters of the Lower Lee - Owenboy catchment and also as a cause of the strongly eutrophic status of Inniscarra Reservoir water quality by the EPA in 2009. Therefore, …

Bs News November/December

Building Services Engineering

No abstract provided.

Weighting The Perceived Importance Of Minimising Economic, Social And Environmental/Cultural Risks In Flood Risk Management, Zeinab Bedri, John O'Sullivan, Mark Adamson

Conference papers

In 2006, the Office of Public Works (OPW) began the National Catchment-based Flood Risk Assessment and Management (CFRAM) Programme through a series of pilot studies. A Multi-Criteria Analysis (MCA) Framework was developed through the CFRAM pilot studies that integrated a range of objectives related to human health and society, the environment and cultural heritage and the economy into the core process of selecting suitable flood risk management measures for a given area or location, and then for prioritising national investments for different schemes and projects. In support of this MCA framework, UCD, was commissioned to undertake a collaborative study with …

Calibrating And Evaluating Dynamic Rule-Based Transit-Signal-Priority Control Systems In Urban Traffic Networks, Md Didarul Alam

Civil and Environmental Engineering Dissertations

Setting the traffic controller parameters to perform effectively in real-time is a challenging task, and it entails setting several parameters to best suit some predicted traffic conditions. This study presents the framework and method that entail the application of the Response Surface Methodology (RSM) to calibrate the parameters of any control system incorporating advanced traffic management strategies (e.g., the complex integrated traffic control system developed by Ahmed and Hawas). The integrated system is a rule-based heuristic controller that reacts to specific triggering conditions, such as identification of priority transit vehicle, downstream signal congestion, and incidents by penalizing the predefined objective …

How Transportation Network Companies Could Replace Public Transportation In The United States, Matthew L. Kessler

USF Tampa Graduate Theses and Dissertations

The quantity of cell phone applications or mobile apps have seen an upsurge at an exponential rate in under a decade. Many have been created for a variety of industries, including transportation. The advent and subsequent commercialized implementation of near-instant transport by a middleman-type of app is now known as a Transportation Network Company or TNC. Examples of the more renowned TNCs are Uber, Lyft and Sidecar.

In recent years, TNCs have cultivated a tremendous following, to the degree of taxicab desertion. Moreover, the massive success of TNCs led to expansion of its capacities into public transportation.

The TNC’s expeditious …

Hollow-Core Frp-Concrete-Steel Bridge Columns Under Torsional Loading, Sujith Anumolu, Omar I. Abdelkarim, Mohanad M. Abdulazeez, Ahmed Gheni, Mohamed Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents the behavior of hollow-core fiber-reinforced polymer-concrete-steel (HC-FCS) columns under cyclic torsional loading combined with constant axial load. The HC-FCS consists of an outer fiber-reinforced polymer (FRP) tube and an inner steel tube, with a concrete shell sandwiched between the two tubes. The FRP tube was stopped at the surface of the footing, and provided confinement to the concrete shell from the outer direction. The steel tube was embedded into the footing to a length of 1.8 times the diameter of the steel tube. The longitudinal and transversal reinforcements of the column were provided by the steel tube …

Establishing The Key Pillars Of Innovation Required To Execute A Successful Bim Strategy Within A Construction Sme In Ireland, Barry Mcauley, Patrick Carroll

Conference papers

The recent resurgence of the Irish Construction Industry comes at a time of global transition towards an information revolution, with technology now playing a vital role within our post-recessionary society. BIM is now seen as a core technology at the forefront of this transformational change which can present Construction SMEs with opportunities to new financial ventures. If any SME organisation is to be successful with BIM adoption then innovation must be the starting point. The aim of this paper is to establish the enabling factors required for innovating a BIM strategy within a SME Construction Organisation. The methodology involved a …

The Effect Of Chemical Composition Of Blast-Furnace Slag On Compressive Strength And Durability Properties Of Mortar Specimens, William J. Johnson

USF Tampa Graduate Theses and Dissertations

In an effort to make structures more sustainable and durable, supplementary cementitious materials are often used to replace cement. Ground granulated blast furnace slag, for instance, is an industrial by-product of iron refinement and is frequently used in concrete mixture design to not only reduce cost, but also increase later-age strength as well as durability. However, published literature indicates that slags with a high alumina content may have a detrimental effect when concrete is exposed to a sulfate environment. ASTM standard C989 does not suggest any information or guidelines regarding using slags with an alumina content between 11-18%. Therefore, the …

Investigation Of Ternary Binder Based Systems In Terms Of Calorimetry, Shrinkage And In-Situ Xrd, Anxhelina Qorllari, Elsa Qoku, Thomas A. Bier, Teuta Dilo

UBT International Conference

Ternary binders are defined in this study as compositions of Calcium Aluminate Cement (CAC), Ordinary Portland Cement (OPC) and Calcium Sulfate (CS̅). Several mixtures were studied, calorimetric and shrinkage technique has been used to follow the hydration during 24 hours. The XRD technique is used as support in the analysis of the hydration products. The results have shown that the initial amount of ��� and �� play a key role in the hydration of ��/���/�� mixtures and especially affect the formation of ettringite. The mechanism of reactions (hydration kinetic) and the reactions speed (acceleration or retardation) depends by the aggregates …

Reducing The Porosity And Sealing Cracks By Using Crystalline Admixture In Conventional Concrete, Visar Krelani, Liberato Ferrara

UBT International Conference

There is a continuous increase of quality on civil engineering materials in developed countries and parallel increase of need for new constructions in developing countries. Professional community should propose solutions for the durability that can resist in different severe environments. The most important factor that can affect concrete durability is represented by the pore distribution. Transport properties can take place through the porous network inside the cementitious composites and the aggregates interface, permitting the ingress of aggressive agents damaging concrete function intrinsically as a material and the wellfunctioning of the entire structure. The use of a crystalline admixture during the …

Using Of Proper Pavement Material For The Intersections With Slow-Moving Traffic, Bekim Selimi

UBT International Conference

Use of proper pavement material for some of intersections need special attention by road designers. At Camp Bondsteel-Kosovo on 2002 were built four road intersections using the concrete as pavement material. Heavy and slow-moving trucks that are turning or accelerating exposed these intersections to some of the highest stress level. After some years this intresections start deteriorating on their surface due to friction. The concrete pavements did not survive this period of usage and after eight years were removed and replaced with asphalt pavements. After more than seven years, the asphalt has shown minor distress but is still in good …

Developing A New Total Sediment Transport Formula, Davut Okeu, Sokol Xhafa, Sevdije Govori, Majlinda Daci

UBT International Conference

Sediment transport is one of the most powerful factor on river hydrology. It has vital importance for water engineering projects. There are many sediment transport formulas in the literature but most of them are derived from small data sets of natural rivers or experimental designs. Each formulation has its own restrictions, which depends on the original dataset of that study. None of them have gained universal acceptance. As a result, investigation towards the development of more accurate and simpler formulae is still necessary and should be continued.

The aim of this study is to derive a new total sediment load …

Heritage Under Pressure The Case Of The “Bypass” In Gjirokastra World Heritage Site Albania, Kreshnik Merxhani, Valmira Bozgo

UBT International Conference

The following article is an account presenting a professional movement opposing a planned and approved project for the construction of a new road known as the “Bypass”, which endangered the Historic Center of Gjirokastra. The project, consisted in the construction of a new road, with the initial aim of diverting automobile traffic from the Bazaar, turning it into a pedestrian zone. However after a few procedural problems were noted, it became clear that the project itself was not fulfilling its original aim, and further more posed a threat to the historical center. During the only public consultation session held for …

The Influence Of The Radius Of The Curve And The Lateral Slope On The Safety Of The Vehicle, Baxhuku Visar, Koca Odisea, Çekiçi Visar

UBT International Conference

The movement of the vehicle in a curve related to the construction of the road is expressed through the influence of the radius of the curve and the transversal inclination of the road. Two of these quantities are fixed quantities ever since the projection and then construction phase of the road. During the vehicle’s movement in the curve, their influence is shown through the critical slide velocity. This critical velocity is defined from the influence of the centrifugal force. For smaller values under critical velocity, this influence is expressed through the safety of the movement or the comfort of the …