Civil and Environmental Engineering Commons^™

Increasing Strength Of Plywood Shear Walls, Elizabeth Claypool, Michelle Dennin

Architectural Engineering

In a recent iteration of an upper-division engineering design lab course at Cal Poly SLO, students were challenged to identify and understand the probable failure mechanism of conventionally built plywood shear walls and hypothesize how they could delay or prevent common failure mechanisms to increase the overall lateral load capacity. After observing the results of a test on a conventional, code specified wall, a solution to integrate metal gauge strapping into edge nailing was developed to address the common failure mechanisms of nail head pull through and panel edge tear out. A shear wall with metal strapping installed between the …

Development Of Probabilistic Failure Pressure Models For Pipelines With Single Corrosion Defect, Kiswendsida J. Kere, Qindan Huang

Civil and Environmental Engineering Faculty Research and Publications

Many models have been developed in the past to predict the failure pressure of a pipeline with a single corrosion defect. However, most of the existing models are conservative and may lead to unnecessary repairs and maintenance in the pipeline risk management. The aim of this study is to develop probabilistic failure pressure prediction models that are suitable for risk assessment of corroded pipelines. The proposed models are developed at three levels of pipe ultimate strength based on a comprehensive database (consist of both experimental and numerical data) established in this study. When comparing with the existing models, it is …

Using Metal-Organic Frameworks (Mof) To Reduce The Carbon Footprint Of Concrete, Mona Ibrahim El-Hallak

Theses

The production of concrete by the construction industry has a massive impact on the environment. The process of manufacturing its main component, cement, releases a considerable amount of anthropogenic carbon dioxide. This thesis is concerned with the production of sustainable and eco-friendly concrete that integrates metal-organic frameworks (MOF) to capture and offset the CO₂ emissions emitted during the production of cement. The main objective is to synthesize a MOF capable of capturing CO₂ in concrete through accelerated carbonation curing and to assess its impact on concrete performance. Different parameters were examined, including the MOF content, initial curing duration, …

Numerical Modelling Of Externally-Bonded Fiber Reinforced Polymer Shear-Strengthened Reinforced Concrete Beams Subjected To Fatigue Loading, Nagwa Ibrahim Fares

Theses

An extensive number of existing structures persistently exposed to fatigue loading such as bridges, offshore structures, pavements, and highways, are in urgent need of repairing and strengthening. This may be attributed to the continuous increase in the load requirements, change of the structure’s function, and meeting current load standards. Among the potential methods of rehabilitation and strengthening of existing reinforced concrete structures, the externally bonding fiber reinforced polymers (FRP) composites are gaining massive popularity and becoming a viable and cost-effective method. Shear failure of reinforced concrete (RC) beams is known to be brittle, which occurs without prior sufficient warnings; therefore, …

Effects Of Experimental Scale On The Adsorption Of Two Pharmaceutical Drugs Detected In Municipal Wastewater Effluent, Michael Moore

Master's Theses

Pharmaceutical drugs are being produced and consumed in increasing quantities every year and are poorly treated by conventional wastewater treatment processes, leading to increasing detection of such compounds in surface water, groundwater, and municipal drinking water. Soil aquifer treatment (SAT) is a promising method for treating these emerging compounds through combined adsorption and degradation of target compounds in soil. This thesis examines the consistency of results from typical studies like adsorption isotherms and soil columns utilized in analysis of SAT performance, across varying experimental scales. The adsorption behavior of two pharmaceuticals was investigated as a function of experimental scale and …

The Impact Of Material And Environmental Properties On The Ettringite - Metaettringite Thermochemical Reaction, Aaron Strand

Dissertations

The use of energy is an essential need for people, with demand constantly increasing due to an increasing population and an increase in living and comfort standards. Since 1965, world energy consumption has quadrupled. During peak utilization, the strain on the grid infrastructure can be immense. As energy demand fluctuates during different times of the day and year, the energy production needs to scale accordingly This creates inefficiencies within the system such as over building generation capacity or losses from start up or ramping up production. This can be alleviated through load leveling where excess energy generated during low demand …

Partial Systems' Analysis Of Traffic Noise Reduction In Tarik Al Jadidah, Beirut, Ibtihal Y. El-Bastawissi, Nour El Baba, Shireen Khalil, Nour El Hage, Rouba Joumblat, Franz Gatzweiler

BAU Journal - Creative Sustainable Development

Traffic noise is considered one of the main pollutants in an urban space and has multiple side effects regarding the physical and mental health of the human being. Tarik Al Jadidah, one of the most densely populated neighborhoods in Beirut City- Lebanon, is selected as urban area for a project-based initiative and the focal point of different studies in BAU Urban Lab. The area suffers from various urban problems, but prominently traffic noise that highly damages the urban residents' quality of life due to its high levels of traffic noise that surpasses the World Health Organization (WHO) guidelines.

BAU Urban …

Evaluating And Incorporating Site Variability In Different Geotechnical Engineering Applications, Md Habibur Rahman

LSU Doctoral Dissertations

Site investigation and characterization of subsurface soil conditions are crucial for geotechnical engineering design and analysis. Geotechnical properties vary inherently from one point to another within the same site. This study focused on evaluating the site variability from cone penetration tests (CPT) and soil boring data, and its implementation into the Load and Resistance Factor Design (LRFD) formulation. The total Coefficient of Variation (COV_R,total) for each site was estimated from COV_R,spatial (Spatial Coefficient of Variation) and COV_R,method (Method Coefficient of Variation) which were then used to calibrate the resistance factors (ϕ_spatial, ϕ_total) …

Hydrodynamic Limitations To Mangrove Seedling Retention In Subtropical Estuaries, Kelly M. Kibler, Christian Pilato, Linda Walters, Melinda Donnelly, Jyotismita Taye

Flow-biota Interaction and Natural Infrastructure Design

Mangrove forest sustainability hinges upon propagule recruitment and seedling retention. This study evaluates biophysical limitations to mangrove seedling persistence by measuring anchoring force of two mangrove species (Rhizophora mangle and Avicennia germinans). Anchoring force was measured in 362 seedlings via lateral pull-tests administered in mangrove forests of two subtropical estuaries and in laboratory-based experiments. Removal mechanism varied with seedling age: newly-established seedlings failed due to root pull-out while seedlings older than 3 months failed by root breakage. Anchoring force of R. mangle seedlings was consistently and significantly greater than A. germinans (GLM: p = 0.002), however force to …

A Review Of Current Construction Guidelines To Inform The Design Of Rammed Earth Houses In Seismically Active Zones, David Thompson, Charles Augarde, Juan Pablo Osorio

Articles

Sustainability in the materials we use for construction is a prime concern, focusing on reducing the embodied energy and carbon footprints of the materials used. The cement used in concrete products is responsible for a significant proportion of Man's CO2 emissions and its production requires substantial energy input, as do fired clay products. For this reason, products formed from unfired earthen materials are of increasing interest and the current challenges include devising means of robust design for strength and to address durability concerns. One form of earthen construction that employs an in-situ method is rammed earth, and it is a …

Investigation Of Elastic Parameters And Pavement Modeling With Eps Geofoam, Engda Kassahun Temesgen

Dissertations - ALL

Models using EPS geofoam rely on input elastic parameters derived from compression tests on small size samples. Young's modulus and Poisson's ratio are parameters required to model isotropic and homogenous material behavior. For the most widely used EPS density grade of 20 Kg/m3 (1.25 pcf), Young's modulus of 4 MPa and Poisson's ratio of 0.1 are commonly used. Use of these values in models led to unreasonable long term deformation predictions that contradicted with field observations. Tests on small samples are prone to edge effects. Edge effects in turn result in underestimation of input elastic parameters. Alternative tests and sensing …

Transformational Leadership And The Adoption Of Sustainability And Asset Management Practices In Ground Transportation Organizations, Mohammad M. Bushahri

Dissertations - ALL

The unprecedented challenges the infrastructure domain has been facing for the past few decades are forcing the authorities and owners of relevant organizations, particularly within the ground transportation sector, to introduce more innovative measures and to mitigate risks by embracing and adopting sustainability and asset management practices. This study examined the relationship between transformational leadership and the embracing and adopting of sustainability and asset management practices in the U.S. ground transportation sector. Further, this study assessed the mediation effect of organizational innovation on the relationship between transformational leadership style and the leaders' perception in terms of adaptation of sustainability and …

Mechanical Property Relationships Of Cement Or Lime Stabilized Soils Throughout A Pavement's Life, Leigh E.W. Ayers

Theses and Dissertations

Soil-cement is an integral part of pavement design, especially in areas that are aggregate deprived, such as Mississippi. Current designs are reliant on the relationship of unconfined compressive strength (UCS) to other mechanical properties. The other properties discussed in this dissertation are Modulus of Elasticity (E), Indirect Tensile Strength (St), and Modulus of Rupture (MOR). This dissertation includes a comprehensive review of past design methods and mechanical property relationships. While some mechanical property relationships were shown to be well understood (i.e. St to UCS), others were not as accurate, especially for the later life mechanical properties (i.e. MOR to UCS …

Impact Of Climate Oscillations/Indices On Hydrological Variables In The Mississippi River Valley Alluvial Aquifer., Meena Raju

Theses and Dissertations

The Mississippi River Valley Alluvial Aquifer (MRVAA) is one of the most productive agricultural regions in the United States. The main objectives of this research are to identify long term trends and change points in hydrological variables (streamflow and rainfall), to assess the relationship between hydrological variables, and to evaluate the influence of global climate indices on hydrological variables. Non-parametric tests, MMK and Pettitt’s tests were used to analyze trend and change points. PCC and Streamflow elasticity analysis were used to analyze the relationship between streamflow and rainfall and the sensitivity of streamflow to rainfall changes. PCC and MLR analysis …

Development And Evaluation Of Seasonal, Continental-Scale Streamflow Forecasts, Elissa Marie Yeates

Theses and Dissertations

Methods of forecasting streamflow using atmospheric ensembles and hydrologic routing have greatly improved over the past decades. These forecasts anticipate the timing and magnitude of streamflow peaks, enabling early warning of floods. Recent advances in atmospheric modeling have enabled production of forecasts months ahead, which are less precise but give a useful sense of trends.

The purpose of this study is to produce and evaluate a seasonal streamflow forecast model using a Muskingum routing hydrologic model coupled with runoff from a land surface model, and atmospheric input from a medium-term atmospheric and precipitation model. To evaluate the skill of the …

Development Of An Analytical Method For Design Of Electromagnetic Energy Harvesters With Planar Magnetic Arrays, Mohsen Amjadian, Anil K. Agrawal, Hani H. Nassif

Civil Engineering Faculty Publications

In this paper, an analytical method is proposed for the modeling of electromagnetic energy harvesters (EMEH) with planar arrays of permanent magnets. It is shown that the proposed method can accurately simulate the generation of electrical power in an EMEH from the vibration of a bridge subjected to traffic loading. The EMEH consists of two parallel planar arrays of 5 by 5 small cubic permanent magnets (PMs) that are firmly attached to a solid aluminum base plate, and a thick rectangular copper coil that is connected to the base plate through a set of four springs. The coil can move …

Development, Characterization, And Modeling Of Physical, Mechanical, And Durability Properties Of Sustainable Ultra-High Performance Concrete, Tawsif M. Hasan

ETD Archive

Ultra-High Performance Concrete (UHPC) is an advanced concrete material with superior mechanical strength, high tensile ductility, and exceptional durability, including negligible permeability. Despite these excellent material properties, the use of UHPC in structural applications is limited because of the high cost of commercially available UHPC products. Therefore, developing non-proprietary UHPC mixtures using local materials is a viable way to reduce the initial cost of UHPC. In this research, sustainable and cost-effective UHPC mixtures were developed using locally sourced materials so that UHPC may be more affordable to a wider variety of applications. Specifically, locally available Type I-II cement, local sand …

Smart Intersections: Cooperative Traffic Control For Longer Battery Life Of Communicant Autonomous Vehicles, Fushata Andani Mohammed

Master of Science in Civil Engineering Theses

Abstract

The recent advances in information and communication technologies have enabled cooperative traffic control at signal-free intersections, which can significantly improve safety of the roads and performance of urban networks. The impacts of cooperative control of traffic on the battery life of communicant autonomous vehicles (CAVs), however, are not necessarily positive. This research develops an analytical model for the battery-capacity loss rate of CAV platoons coordinated to pass through signal-free smart intersections with no interruption. The main objective of the research is to demonstrate the importance of adjusting the macro-level setting of the cooperative control system for enhancing the battery …

The Living Breakwaters Pdr Efforts: Conceptual Scheduling, Calvin O. Walters Jr.

Publications and Research

On October 29, 2012, Superstorm Sandy caused nearly $19 billion in damages in New York City including 69,000 residential units across the five boroughs. This disaster precipitated a post-disaster-rebuilding (PDR) project including roughly $4.2 billion in a Community Development Block Grant allocated towards PDR projects. A portion of the grant was used to construct a living breakwater in Tottenville, Staten Island, consisting of a resiliency approach to risk reduction through erosion prevention, wave energy attenuation, and enhancement of ecosystems and social resiliency to improve resistance to storms for the community of Tottenville. The ridges of each breakwater are designed with …

Analysis Of Properties Of Asphalt Binder With The Addition Of Lignin, Frank A. Martin Junior

Honors College Theses

As asphalt ages, its resistance to shear diminishes due to a change in composition, resulting in the need for repaving of roads. Current additives to asphalt binder focus on increasing the strength of the binder, but do nothing to prevent the ageing of the asphalt binder. Lignin is a biological additive that is known for its resistance to ultraviolet radiation. This research aims to study Lignin as an asphalt additive, which exhibits properties that can increase the resistance of degradation due to aging, as well as increasing the strength of the asphalt binder. This was done through the comparison of …

Sustainability In Construction Practices As Emphasis On Environmental Investing In Esg Model Grows, Maddie Heal

Management Undergraduate Honors Theses

The purpose of this research is to emphasize the importance of growing investment on environmental initiatives in business ESG models in regard to sustainable practices in construction. The ESG acronym is known as the environmental, social, and governance efforts that businesses strive to incorporate in their models to increase the responsibility of operations.

Investors continue to seek out responsible businesses when choosing which ventures to pursue. The analysis of the current construction crisis, current investments in the right direction of Eco-friendly design regarding construction, and the threats and benefits incentivizing those investments elucidates the need to emphasize socially responsible investment …

Port Infrastructure Resilience Through Combined Wind-Surge Demand Characterization, Kaley Callaway

Graduate Theses and Dissertations

The United States economy is reliant on maritime transportation for 70% of imports and exports. Structures that are integral to the operation of ports, such as cranes, are jeopardized when tropical storms approach land. While wind is the only environmental load used to design dockside container cranes, storm surge often accompanies severe wind events and can create large structural loads. This study focuses on determining coupled storm-surge demands and the effect of waves on dockside container cranes. A damage index prediction tool that considers both maximum wind speed and storm surge height is developed and applied to historical hurricane data …

Refining Particle Size Specification For Asphalt Emulsion, Pedro Luis Diaz Romero

Graduate Theses and Dissertations

Pavements begin to deteriorate as soon as they are constructed, and traffic is released. The rate at which a pavement deteriorates depends on the material quality, the environment, and the loads carried. To properly preserve pavements and extend their life, various pavement preservation treatments are used. For flexible pavements, a considerable number of these treatments use asphalt emulsion (which are refer to simply emulsions from here on). Emulsions are classified based on their particle charge and reactivity. Emulsions used in chip seals are usually of rapid set reactivity and are classified based on tests over fifty years old.

It has …

Cyclic Behavior Of Laterally Skewed Special Moment Frame Connections: Experimental Testing And System-Level Analyses, Mohammad Hossein Kashefizadeh

Graduate Theses and Dissertations

Special moment frames (SMFs) are frequently used in high seismic areas for architecturally constrained designs. SMFs provide lateral system stiffness without the use of braces that often obstruct views and architectural features. Current American Institute of Steel Construction (ASIC) provisions (AISC 341-16) provide prequalified SMF connection details; however, all prequalified details only consider orthogonal connections between the beam and column. This dissertation investigates the effect of adding skew within SMF beam-to-column connections. The study presented herein involves system-level dynamic time-history analyses of skewed SMF connections, the analytical component-level investigation into the effect of the concrete slab on behavior of the …

Rapid Non-Nuclear In Situ Density And Moisture Content Measurement Of Soil, Mateo Lopez

Graduate Theses and Dissertations

Adequate soil compaction is important for the stability and safety of structures and transportation infrastructure. Thus, methods utilized to obtain properties that control the quality of compaction in the field are essential to ensure proper construction. These properties include; total density, dry density, total unit weight and dry unit weight of the compacted soil. The most common method to measure these properties in the field is the Nuclear Density Gauge. Moisture content and density results are obtained using the Nuclear Density Gauge in one to four minutes. However, this method requires specialized training and strict storage requirements in addition to …

Validation Of Cfd Tornado Pressure On Building And Wind Field With Ttu Vortex Chamber Measurements, Sumit Verma

Graduate Theses and Dissertations

Structural failure of low-rise buildings is the root cause of higher number of casualties, death tolls and economic losses at the place of occurrence of tornadoes. Proper design of low-rise buildings in tornado-prone areas require accurate estimation of tornado-induced wind loads; however, exhaustive research to estimate the wind loads reliably on buildings during tornadic events is still lacking. Several studies have been carried out to investigate the magnitude of forces induced by tornado winds on buildings from experimental as well as computational side. However, the wind pressures obtained on the building from different experimental studies have shown significant variation from …

A Campus Connected: An Analysis Of University Outdoor Spaces, Skylar Wilson

Undergraduate Honors Theses

The purpose of this research is to analyze the evolution of outdoor renovations on East Tennessee State University’s campus by examining the effects these renovations have had on students and faculty, and then using this data to propose possible successful renovations to the remainder of the University Commons project. To complete this project, data was obtained through East Tennessee State University administrative faculty interviews, surveys of students residing in campus resident halls, and observations. By examining the impact on behavior, designers and developers are then able to successfully determine the factors that aid in positively influencing human behaviors. Design suggestions …

Hydrodynamic Forces On Stream-Crossing Bridges – Consideration Of Flow Parameters, Bridge Geometry, And Debris, Shah Md Imran Kabir

Civil Engineering Dissertations - Archive

ABSTRACT: This thesis examines the interaction of flood flow with bridge superstructures by considering the effects of the flow parameters, bridge geometry, debris, and bridge substructures. The hydrodynamic forces are expressed by using force and moment coefficient charts to portray the effect of bridge submersion, bridge position with respect to the channel bed, flood velocity, and bridge geometry. Of the 580,000 bridges in the United States, 83% span streams and rivers that may subject them to floods and debris loads. Although bridges are designed to withstand hydrodynamic forces, the most frequent causes of failure are attributed to hydraulic events, including …

Asset Management Of Wastewater Interceptors Adjacent To Bodies Of Water, Mohammad Bani Fawwaz

Civil Engineering Dissertations - Archive

This dissertation presents the viability of managing a pipeline network adjacent to bodies of water to maximize asset life by evaluating the significant factors that affect the condition levels of pipeline assets. Pipeline asset management derives from pipelines’ physical conditions, condition rating, and serviceability through testing, monitoring, and analyzing rupture history. The remaining asset life and structural condition of the pipeline network running near and under bodies of water are often hard to predict. In case of pipeline failure, exuberant damages will occur to the surrounding environment, adding up to disruption in service and repairing costs. This research develops Multinomial …

Wave Interactions And Energy Cascade, Bailey Downing

Civil Engineering Undergraduate Honors Theses

Structural engineers design buildings and their components to withstand code-specified wind loads. The ASCE 7-16 manual sets the standards for calculating wind loads in the U.S. Depending on the velocity of wind, deflections may occur as wind passes through the building. The pressure reported from ASCE are based on wind tunnel measurements. The peak pressure from ASCE 7 is much less than what is measured from the field for a low-rise building. As an alternative economic tool, Computer modeling has been developed to help with this dilemma. Methods based on computational fluid dynamics (CFD) are used to calculate velocities and …