Petroleum Engineering Commons^™

Optimum Biodiesel Production Using Ductile Cast Iron As A Heterogeneous Catalyst, Nada Amr El-Khashab, Marwa Mohamed Naeem, Mai H. Roushdy

Chemical Engineering

Biofuels production become a target for many researchers nowadays. Biodiesel is one the most important biofuels that are produced from biomass using economics and modern techniques. The ductile cast iron solid waste dust is one of the wastes produced by the cast iron industry which has a bad effect on the environment. This paper investigates the possibility of reusing ductile cast iron solid waste as a biodiesel heterogeneous catalyst used in its production from sunflower waste cooking oil. Four reaction parameters were chosen to determine their effect on the reaction responses. The reaction parameters are M:O ratio, reaction time and …

Characterization Of Gas Hydrate Formation And Its Impact On Slope Stability In Offshore Environments, Sulav Dhakal

LSU Doctoral Dissertations

Natural gas hydrates (NGH) are predominantly methane hydrates formed at high pressure and low temperature conditions typically in submarine sediments and permafrost. This dissertation is focused on the submarine methane hydrates formed by upward migration of free and dissolved gas. The methane gas stored within natural hydrates has more energy potential than all the combined oil and gas resources around the world. Numerical simulation of fluid flow, heat transport, and geomechanical stresses is used to characterize and evaluate the saturation, distribution, reservoir quality, and geohazards associated with hydrate-bearing sediments. Coupled thermo-hydro-mechanical (THM) simulation of hydrate formation, dissociation, and slope stability …

A Drift-Flux Model For Upward Two-Phase In Pipes With High Velocity Flows, Woochan Lee

LSU Doctoral Dissertations

This study proposes the evaluation and development of a drift-flux model for upward two-phase high-velocity flow in large diameter pipes. A case where the proposed model is applicable is WCD (Worst-Case-Discharge) calculations for offshore wells. WCD assumes relatively larger pipe diameters and higher flow rates than the flow experiments at laboratory conditions utilized to validate and develop most of the flow models available in the literature.

Most of the two-phase flow models describe flow regime transitions as discrete processes by assigning the required void fraction or velocity for each flow regime transition. Therefore, for each flow regime, flow-regime-dependent correlations or …

A New Look At Landslides Of The Vermilion And Echo Cliffs, Northern Arizona, Conor M. Watkins, J. David Rogers

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The Vermilion and Echo Cliffs form a nearly continuous escarpment more than 160 km long within the Colorado Plateau physiographic province of North America. The cliffs overlie the Marble Platform in northern Arizona and are located along the Colorado River, just upstream of the Grand Canyon. Large rotational block landslides mantle the erosional escarpment along most of its extent. Although these landslides have been noted for over 100 years, their likely origin has never been explained. Landslide failure surfaces appear to be influenced by the Petrified Forest Member of the Triassic Chinle Formation, a shale layer containing smectite clay weathered …

Comprehensive Evaluation Of Self-Healing Polyampholyte Gel Particles For The Severe Leakoff Control Of Drilling Fluids, Lili Yang, Chunlin Xie, Tian Ao, Kaixiao Cui, Guancheng Jiang, Baojun Bai, Yongwei Zhang, Jun Yang, Xingxing Wang, Weiguo Tian

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Lost circulation has been a serious problem to be solved in many drilling practices during oil, gas and geothermal well drillings. Many materials have been developed and evaluated for the purpose. However, their performance to plug severe leakoff is very limited. Herein, an injectable self-healing hydrogel based on polyampholyte with sulfonated and quaternary ammonium functionalities (P(MPTC-co-NaSS)) was developed and comprehensively evaluated to prevent the severe loss of fluids to formation. By incorporating cation-π (π is for aromatic residues) interaction, the hydrogel shown self-healing property and robustness in severe environment (temperature, salt) by comparison with other hydrogels merely consisting of cation-anion …

Desalination Waste Revitalization Using Carbon Capture: Process Optimization Using Machine Learning, Ahmed Mohamed Elsayed

Theses

Over the next five to ten years, desalination will play an ever-important role in our society. Developing nations will look at desalination from the point of water scarcity, while developed nations will consider the perspective of the Water-Energy-Food nexus. With current technology, for every liter of freshwater produced, one and a half liters is thrown away as waste. This body of research proposes to employ chemical precipitation in ammoniated brine solutions, that have reasonably high ionic concentrations. CO2 absorption in Bubble Column Reactors can reduce sodium ions by precipitating NaHCO3. Also, the absorbed CO2 can reduce chloride ions and induce …

Lithospheric Structure Underneath The Archean Tanzania Craton And Adjacent Regions From A Joint Inversion Of Receiver Functions And Rayleigh-Wave Phase Velocity Dispersion, Tuo Wang, Stephen S. Gao, Qiuyue Yang, Ling Chen, Kelly H. Liu

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Lithospheric structure beneath the Archean Tanzania craton and adjacent regions, including segments of the East African rift system (EARS) and the Proterozoic-early Paleozoic orogenic belts between the EARS and the craton, is imaged by a joint inversion of receiver functions and Rayleigh wave dispersion measurements derived from ambient seismic noise for shorter periods and teleseismic data for longer periods. Our resulting crustal thickness, crustal VP= VS measurements and 3D shear-wave velocity model for the upper 120 km show a clear spatial correspondence with major surficial geological features. The new results suggest the presence of a mafic layer in the bottom …

Sanitary Ware Waste As A Source For A Valuable Biodiesel Catalyst, Mai H. Roushdy

Chemical Engineering

Biofuel is a type of fuel that is made from biomass using modern techniques rather than the relatively slow geological processes that lead to the development of fossil fuels. In Europe, biodiesel is the most widely used biofuel. The sanitary ware industry generates a lot of hazardous waste, such as waste gypsum molds. These molds are broken, pulverized, and reacted with NaCO3 to make CaCO3, which is then heated to produce CaO. The resulting CaO catalyzes the reaction between waste frying oil and methanol for biodiesel synthesis. To evaluate the effect of reaction parameters on the production of biodiesel, the …

Chitosan/Polyacrylamide Green Gels For Water Control In High-Temperature Reservoirs, Mohamed Shamlooh, Reem Elaf, Ibnelwaleed A. Hussein, Mohammed Saad, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The rheology of a gel system composed of polyacrylamide (PAM) and chitosan is studied under typical reservoir conditions. The impacts of the degree of chitosan deacetylation, temperature, and salinity on the gelation behavior are assessed. The said system was prepared under ambient conditions and matured for 24 h at altered temperatures ranging from 50 up to 125 °C. An optimum formulation has been identified considering the rheological response and the initial viscosity constraints. The increase in the degree of syneresis with the degree of deacetylation indicates the long-Term thermal stability of the gels. Ammonium chloride was an effective retarder for …

Impact Of Polymer Rheology On Gel Treatment Performance Of Horizontal Wells With Severe Channeling, Jianqiao Leng, Mingzhen Wei, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Gel treatment has been a cost-effective method to control the conformance of a reservoir with severe heterogeneity problems. The water channels in such reservoirs can be classified as open fractures or high permeability porous media with pore-throat network. Many simulation studies have been conducted to discuss gel treatment performance for conformance control. However, nobody considered the polymer rheology difference in open fractures and porous media in simulation. Previous simulation studies also ignored the residual resistance factor as a function of rock permeability rather than a constant parameter. In this study, a conceptual simulation model was established to simulate the linear …

In-Situ Generation Of Hydrocarbons From Kerogen Using Electromagnetic Radiation, Forrest Green

Graduate Theses & Non-Theses

From using surface seeps to modern day exploitation of hydrocarbon source rocks, the petroleum industry is awaiting the next big innovation, accelerated kerogen conversion. In the industry’s history, electromagnetic radiation (EMR) has been used for exploration and now it will be taken to the extreme by determining an effective and efficient method to synthetically generate readily available hydrocarbons. The study starts with examining and defining what kerogen is and its importance as a source material. A strong understanding of what kerogen is, and an analysis of other in-situ projects presents an opportunity to study the finer details of kerogen’s conversion …

Possible Storage Of Co₂ In Saline Aquifer: Storage Factor Estimation, Sarah Abdul Aziz Al-Tamimi

Theses

The objective of this study is to perform laboratory measurements and a CO₂ underground storage study to cover the knowledge gap on CO₂-Brine relative permeability and assess various variables on the storage of CO₂ in a selected aquifer. Several factors that affect CO₂ storage have been discussed in the literature. These include both macroscopic and microscopic displacement efficiency of brine as a function of CO₂ pore volume injected. It is clear from the literature that there is still more work needed to investigate the effect of various variables such as formation temperature, brine viscosity, and the possible presence of free …

High-Octane Gasoline Production Processes Using Catalysts Containing Platinum, Dilnoza Mauletbayevna Ametova, Duysenbay Xojabayevich Abdikamalov, Edil Abilov

Karakalpak Scientific Journal

The catalytic reforming process is designed to increase the detonation resistance of gasolines and to obtain individual aromatic hydrocarbons, mainly benzene, toluene, xylenes - petrochemical feedstocks. It is important to obtain a cheap hydrogen-containing gas in the process for use in other hydrocatalytic processes. The importance of catalytic reforming processes in oil refining increased significantly in the 1990s. due to the need to produce unleaded high-octane gasoline

Hydrogen Flooding Of A Coal Core: Effect On Coal Swelling, Stefan Iglauer, Hamed Akhondzadeh, Hussein Abid, Adriana Paluszny, Alireza Keshavarz, Muhammad Ali, Ausama Giwelli, Lionel Esteban, Joel Sarout, Maxim Lebedev

Research outputs 2022 to 2026

Hydrogen is a clean fuel which has the potential to drastically decarbonize the energy supply chain. However, hydrogen storage is currently a key challenge; one solution to this problem is hydrogen geo-storage, with which very large quantities of H2 can be stored economically. Possible target formations are deep coal seams, and coal permeability is a key parameter which determines how fast H2 can be injected and withdrawn again. However, it is well known that gas injection into coal can lead to coal swelling, which drastically reduces permeability. We thus injected H2 gas into a coal core and measured dynamic permeability, …

Continental Break-Up Under A Convergent Setting: Insights From P Wave Radial Anisotropy Tomography Of The Woodlark Rift In Papua New Guinea, Youqiang Yu, Frederik Tilmann, Dapeng Zhao, Stephen S. Gao, Kelly H. Liu

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

To explore the dynamic mechanism of continental rifting within a convergent setting, we determine the first P wave radial anisotropic tomography beneath the Woodlark rift in southeastern Papua New Guinea, which develops within the obliquely colliding zone between the Australian and southwest Pacific plates. The rift zone is depicted as localized low-velocity anomalies with positive radial anisotropy, which rules out a dominant role of active mantle upwelling in promoting the rift development and favors passive rifting with decompression melting as main processes. Downwelling slab relics in the upper mantle bounding the rift zone are revealed based on observed high-velocity anomalies …

Morphology Of Mos2 Nanosheets And Its Influence On Water/Oil Interfacial Tension: A Molecular Dynamics Study, Yang Feng, Jirui Hou, Yulong Yang, Shuting Wang, Dongsen Wang, Tingting Cheng, Zhenjiang You

Research outputs 2022 to 2026

Plate-shaped nanoparticles exhibit huge potential for a broad range of cutting-edge applications in interfacial-based science and technology, such as enhanced oil recovery in hydrocarbon reservoirs, owing to their remarkable features in superior affinity toward interfaces. Understanding the adsorption behavior of nanosheets (NSs) self-assembled at the water/oil interface (W/O interface) is crucial to elucidate the variation of interfacial tension (IFT) and establish special design criteria for efficient industrial use of NSs. Here we present a molecular dynamics study to reveal the morphology of carbon-chain modified molybdenum disulfide (MoS₂) nanosheets. The stress exerted on a nanosheet is analyzed. The simulation …

Selective Penetration Behavior Of Microgels In Superpermeable Channels And Reservoir Matrices, Yang Zhao, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Gel treatment is an effective way to attack excessive water production in many mature oilfields around the world. Selective penetration is desired for successful gel treatments. That is, gel materials should easily penetrate the target zones (i.e., channeling features such as superpermeable channels) without entering/damaging the nontarget zones (i.e., reservoir matrices or oil zones). This study revealed that presence of threshold penetration pressure (ΔPth) was responsible for selective penetration behavior of tested microgels. The concept of ΔPth was utilized to figure out favorable working conditions for effective gel treatments. Microgel dispersions were injected into superpermeable (super-k) sandpacks (mimicking super-k channels …

Early Global Mantle Chemical And Isotope Heterogeneity Revealed By The Komatiite-Basalt Record: The Western Australia Connection, I. S. Puchtel, R. W. Nicklas, J. Slagle, M. Horan, R. J. Walker, E. G. Nisbet, Marek Locmelis

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Although the heterogeneous nature of the chemical composition of Earth's mantle is now well established, the origin and longevity of the heterogeneities continue to be debated. In order to further study early-Earth heterogeneities, we present a set of Sm-Nd, Lu-Hf, Re-Os, and Hf-W isotope and lithophile and siderophile element abundance data for komatiites and basalts from the ∼3.53 Ga Coonterunah, ∼3.34 Ga Kelly, and ∼3.18 Ga Ruth Well and Regal systems of the Pilbara Craton in Western Australia. The Sm-Nd, Lu-Hf, and Re-Os isotope data yield isochrons consistent with the accepted emplacement ages of the respective komatiite-basalt lavas. The mantle …

Potassic Volcanism Induced By Mantle Upwelling Through A Slab Window: Evidence From Shear Wave Splitting Analyses In Central Java, Fansheng Kong, Stephen S. Gao, Kelly H. Liu, Jiabiao Li

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

To delineate the mantle flow fields in the vicinity of a previously proposed slab window and the possible roles that they may play in the formation of potassic volcanism in Central Java, we conduct shear wave splitting analyses using both local S and teleseismic XKS waves (including SKS, SKKS, and PKS) recorded by 121 onshore stations and two ocean bottom seismometers (OBSs). The XKS fast orientations from the OBSs are trench normal and in accord with previous subslab anisotropy measurements. In the eastern part of Central Java, the XKS and local S fast orientations from the onshore stations are mostly …

Wettability Alteration Process At Pore-Scale During Engineered Waterflooding Using Computational Fluid Dynamics, Yongqiang Chen, Ping Chang, Guang Xu, Quan Xie

Mining Engineering Faculty Research & Creative Works

Engineered waterflooding modifies chemistry of injected brine to efficiently and environmentally friendly enhance oil recovery. The common practice of engineered waterflooding includes low salinity waterflooding (LSW) and carbonated waterflooding. Among these oil recovery methods, wettability alteration has been perceived as a critical physicochemical process for additional oil recovery. While extensive work has been conducted to characterize the wettability alteration, the existing theory cannot explain the conflict oil recovery between secondary mode (injecting engineered water at the very beginning of flooding) and tertiary mode (injecting engineered water after conventional waterflooding), where secondary engineered waterflooding always gives a greater incremental oil recovery …

Descriptive Statistical Analysis Of Experimental Data For Wettability Alteration With Surfactants In Carbonate Reservoirs, Ya Yao, Mingzhen Wei, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Surfactants have been the widely used agents to alter the wettability of carbonate rocks to more water-wet and enhanced oil recovery (EOR). As one of major EOR methods, an effective surfactant huff-puff application design requires comprehensive guidelines about where, how, and when this method could be applied. In order to construct such guidelines, a dataset including 338 effective surfactant imbibition tests is established by collecting information from nearly 50 publications. Based on this dataset, descriptive statistical analysis methods are used to conduct data analysis, including three main parts. The first part establishes the application guidelines for surfactant huff-puff treatments which …

Laboratory Evaluation Of Placement Behavior Of Microgels For Conformance Control In Reservoirs Containing Superpermeable Channels, Yang Zhao, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Gel treatment has been proven an effective method to attack excessive water production in many mature oilfields. However, not all of the application projects have successful stories. The effectiveness of a gel treatment largely depends on the transport and placement behavior of gel materials in reservoirs to be treated. In this work, we carried out systematic studies to investigate the transport, placement, water-blocking ability, fluid diversion and sweep improvement, and matrix damage effect of micrometer-sized preformed particle gels (microgels) in reservoirs containing superpermeable (super-K) channels. The impact of the channel/matrix permeability contrast and the particle/pore size ratio in the channels …

Synthesis And Evaluation Of A Novel Polyacrylamide Functionalized Nano-Silica As A Calcium Carbonate Inhibitor In Upstream Applications, Nadhem Ismail, Ali Alshami, Ibnelwaleed A. Hussein

Chemical Engineering Faculty Publications

Calcium carbonate scale forms in production and injection wells, precipitating upon pressure and temperature changes, incompatible water mixing, and dehydration. Production shutdown is one of the most dramatic consequences caused by calcium carbonate scale formation. We synthesized, characterized, and tested a polyacrylamide functionalized nano-silica (PAM-SiO₂NPs) inhibitor that prevents calcium carbonate formation at high temperatures and high brine. Positive compatibility results were confirmed before the inhibition efficiency test, whereby the efficiency was calculated by quantifying the calcium ions left in solution using ICP-OES. The inhibitor was effective at temperatures of 40, 60, and 80 °C, with pH values of …

Asphaltene Thermodynamic Precipitation During Miscible Nitrogen Gas Injection, Mukhtar Elturki, Abdulmohsin Imqam

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

For many years, miscible gas injection has been the most beneficial enhanced oil recovery method in the oil and gas industry. However, injecting a miscible gas to displace oil often causes the flocculation and deposition of asphaltenes, which subsequently leads to a number of production problems. Nitrogen gas (N2) injection has been used to enhance oil recovery in some oil fields, seeking to improve oil recovery. However, few works have implemented N2 injection and investigated its effect on asphaltene precipitation and deposition. This research investigated the N2 miscible flow mechanism in nanopores and its impact on asphaltene precipitations, which can …

Experimental Evaluation Of Liquid Nitrogen Fracturing On The Development Of Tight Gas Carbonate Rocks In The Lower Indus Basin, Pakistan, Muhammad Ali, Abdul Majeed Shar, Aftab Ahmed Mahesar, Ahmed Al-Yaseri, Nurudeen Yekeen, Khalil Rehman Memon, Alireza Keshavarz, Hussein Hoteit

Research outputs 2022 to 2026

Tight gas carbonate formations have enormous potential to meet the supply and demand of the ever-growing population. However, it is impossible to produce from these formations due to the reduced permeability and lower marginal porosity. Several methods have been used to extract unconventional tight gas from these reservoirs, including hydraulic fracturing and acidizing. However, field studies have demonstrated that these methods have environmental flaws and technical problems. Liquid nitrogen (LN₂) fracturing is an effective stimulation technique that provides sudden thermal stress in the rock matrix, creating vivid fractures and improving the petro-physical potential. In this study, we acquired …

Heterogeneous Biodiesel Catalyst From Steel Slag Resulting From An Electric Arc Furnace, Mai H. Roushdy

Chemical Engineering

Biodiesel is one of the most environmentally friendly and renewable fuels, as it is a non-polluting fuel and is made from living resources, such as vegetable oils. The steel industry generates a variety of solid wastes, including electric arc furnace slag (EAFS). The synthesis of biodiesel from waste sunflower cooking oil was examined in this study, utilizing EAFS as a catalyst, which mainly contains ferric and ferrous oxides, calcium oxide, and silica. To evaluate their impact on biodiesel production, four independent variables were chosen: temperature (50–70 ◦C), catalyst loading (1–5%), methanol-to-oil (M:O) molar ratio (5–20), and time (1–4 h). The …

Application Of Gravity Data For Hydrocarbon Exploration Using Machine Learning Assisted Workflow, Oluwafemi Temidayo Alaofin

LSU Master's Theses

Gravity survey has played an essential role in many geoscience fields ever since it was conducted, especially as an early screening tool for subsurface hydrocarbon exploration. With continued improvement in data processing techniques and gravity survey accuracy, in-depth gravity anomaly studies, such as characterization of Bouguer and isostatic residual anomalies, have the potential to delineate prolific regional structures and hydrocarbon basins. In this study, we focus on developing a cost-effective, quick, and computationally efficient screening tool for hydrocarbon exploration using gravity data employing machine learning techniques. Since land-based gravity surveys are often expensive and difficult to obtain in remote places, …

Comprehensive Evaluation Of Novel Medium-Temperature And High-Temperature Resistant Re-Crosslinkable Preformed Particle Gels For Conformance Control, Zhanmiao Zhai

Masters Theses

"Gel treatment has been widely used to control excessive water production and improve oil recovery in mature oilfields. In comparison to traditional preformed particle gel (PPG), re-cross linkable preformed particle gel (RPPG) has a significant advantage in treating abnormal features such as open fractures, fracture-like channels, and void space conduits (VSC). This research provides a comprehensive evaluation of two novel RPPG products developed in our lab: medium-temperature resistant RPPG (MT-RPPG) for a Middle East reservoir and a high-temperature resistant RPPG (HT-RPPG) for North Sea reservoirs (130 ^oC).

We assessed the effect of the monomer types and concentration, pH, salinity, …

Evaluation Of Novel Preformed Particle Gels For Conformance Control And Acid Stimulation Through Core Flooding Tests, Shuda Zhao

Doctoral Dissertations

"Acid stimulation and conformance control are two major methods to improve oil production. This study systematically evaluates two newly developed gels: Degradable Preformed Particle Gel (DPPG) and Re-crosslinkable Preformed Polymer Gel (RPPG). DPPG is designed to be a temporary plugging agent for acid stimulation and can self-degrade into a water-like fluid. RPPG is designed for reservoir sweep efficiency improvement and can re-crosslink to each other and form an immobile bulk gel after being placed in fractures or fracture-like conduits.

For DPPG, this study evaluates the effect of monomer, crosslinker, and initiator concentration on the swelling and degradation performance. Results show …

Whitening Of Calcium Carbonate Tailings Using Attrition Process: A Case Study Of Khar Toum Deposit, Lopburi Province, Thailand, Bancha Wongkaewphothong

Chulalongkorn University Theses and Dissertations (Chula ETD)

Calcium carbonate (CaCO3) is one of the industrial minerals that usually use in various applications in many industries (e.g., plastic, rubber, paint, paper). However, salable CaCO3 products need to meet the requirement for each application. Whiteness is one of property that really important especially the application that concern about the color like paint and paper industries. In this study, to recover and utilize out of spec ores, the effects of attrition scrubbing process (i.e., retention time and solid in pulp) on the whiteness of the CaCO3 tailings were investigated. The CaCO3 samples were screened to obtain –300, +300–600, +600–1000, +1000–2360, …