Petroleum Engineering Commons^™

Evaluation Of Smart Water Flooding In A Selected Uae Carbonate Oil Reservoir, Mohammad Jasem Khalifi

Chemical and Petroleum Engineering Theses

Water flooding is by far the most common method of improved oil recovery applied in oil reservoirs. Water is the cheapest source of external energy that has been used over decades in water flooding schemes, provided that the damage does not adversely affect its injectivity. Displacement efficiency of water flooding can be significantly affected by crude oil/water/rock interactions. Historically, some consideration was given to such interactions in the practice of reservoir engineering. In recent years, extensive research in this area has documented that higher oil recoveries can be obtained when low-salinity water is injected in a formation with high salinity …

Removal Of Carboxylic Acids And Water From Pyrolysis Oil, George Alexander Marshall

Graduate Theses and Dissertations

Over 70% of the world’s energy consumption is provided by fossil fuels and with those reserves depleting at a fast rate, alternative energy sources or methods are needed to support the world’s energy needs. This research was done in an attempt to make it more economically feasible to produce fuel products, such as bio-diesel, from the upgrading of bio-oil obtained from the pyrolysis of biomass waste material such as sawdust. The high water and oxygenated compound content of bio-oil make it undesirable for fuel use; however, two methods involving surface modified commercial membranes were utilized in hopes of overcoming these …

Plasticized Polymer Coatings For Sh-Saw Sensors For High Sensitivity And Long-Term Monitoring Of Btex Analytes In Liquid Phase, Pintu Adhikari

Master's Theses (2009 -)

BTEX compounds (benzene, toluene, ethylbenzene, and xylene) are constituents of crude oil and hazardous to human health. Among them, benzene has the lowest maximum contaminant level for drinking water because of its carcinogenicity. Spills or leakage from underground storage tanks or hazardous waste sites can contaminate nearby groundwater with these volatile organic compounds. Therefore, it is very important to detect the presence of BTEX contamination as early as possible in order to start the remediation process and maintain a healthy environment. To develop an in-situ continuous monitoring sensor system, shear horizontal surface acoustic wave (SH-SAW) sensor devices are being investigated …

Exploring The Effects Of Aromatic Molecules In Chemical Enhanced Oil Recovery, Jacob M. Crain, Cliff Johnston, Rituraj Borgohain

The Summer Undergraduate Research Fellowship (SURF) Symposium

Chemical enhanced oil recovery (cEOR) methods are being used as a viable contributor to the world’s growing energy demands. Due to the complex chemical composition of crude oil, attempting to optimize the surfactant concentration and salinity of formulations is done empirically. This process can be very time intensive due to the wide variety of surfactant structures available for cEOR. Surfactant selection is typically done by matching the average chain length of the oil with that of the surfactant. In this study, we are trying to understand how aromatic structures present in Illinois Basin crude oil interact with surfactants. This will …

Initial Structural Subsidence As Reflected In Morrowan And Atokan (Pennsylvanian) Subsurface Stratigraphy, Northern Arkoma Basin, North-Central Arkansas, Fatimah Taher Nahi Al Asadi

Graduate Theses and Dissertations

The Arkoma Basin is a carboniferous foreland basin that is known for its prolific gas production. The objective of this research is to study the initial subsidence of the basin by analyzing the strati-graphic and structural features of the study area. This was accomplished through IHS Petra, Surf-er 13, and Win-Tensor software. Field work studies comprised a large part of this study. Also, a seismic profile and Google earth elevation profiles are among the methods used to study the initial subsidence of the Arkoma Basin. The study area within the basin represents a transitional zone from the shelf into the …

Fugitive Emissions, University Of North Dakota. Energy And Environmental Research Center

EERC Brochures and Fact Sheets

Fact sheet about fugitive emissions, their causes, and U.S. Environmental Protection Agency methods of detection and regulation. [This item is an outdated or superseded version and retained for historical purposes only. It may no longer reflect current information, policies, or practices.]

The Exacerbating Effect Of Coastal Erosion To Orphan Well Risk Analysis In Terrebonne Parish, Taylor Reeves

Honors Capstones

No abstract provided.

Investigation Of The Use Of A Plasticizer-Polymer Sensor Coating With Improved Long-Term Stability In The Liquid Phase, Laura Jeanne Alderson

Master's Theses (2009 -)

Benzene is one of the volatile organic compounds present in crude oil and gasoline. Leakage from underground storage tanks or hazardous waste sites can introduce benzene contamination into nearby groundwater. Benzene is a known carcinogen and its exposure is limited by the Environmental Protection Agency to 5 parts per billion (ppb) in drinking water. Early, accurate detection of the presence of benzene contamination in groundwater supplies is extremely important. Shear horizontal surface acoustic wave (SH-SAW) devices with a chemically sensitive coating can be used for the detection of volatile organic compounds in liquid, such as BTEX (benzene, toluene, ethylbenzene and …

Oil Recovery By Polymer Flooding; Sensitivity Analysis To Technical Parameters, Rana Osama Fahmi Saqer

Theses

Numerous enhanced oil recovery techniques including miscible gas injection, chemical, thermal and other methods are applied at the third phase of production after both primary and secondary recovery have been exhausted. Polymer flooding is one of the chemical methods that recover more oil by decreasing the mobility of the system; by increasing the viscosity of the injected water that results in an improvement in the volumetric sweep efficiency.

The objective of this work is to asses and select the development options using polymer process that maximize oil recovery for a synthetic reservoir model where technical parameters are optimized thoroughly.

Reservoir …

Oil Recovery By Flooding; Sensitivity Analysis To Technical Parameters, Rana Osama Fahmi Saqer

Theses

Numerous enhanced oil recovery techniques including miscible gas injection, chemical, thermal and other methods are applied at the third phase of production after both primary and secondary recovery have been exhausted. Polymer flooding is one of the chemical methods that recover more oil by decreasing the mobility of the system; by increasing the viscosity of the injected water that results in an improvement in the volumetric sweep efficiency.

The objective of this work is to asses and select the development options using polymer process that maximize oil recovery for a synthetic reservoir model where technical parameters are optimized thoroughly.

Reservoir …

Contact Angle And Ift Measurements Of Smart Water At Elevated Temperatures And Pressures For Evaluating Wettability In A Selected Carbonate Reservoir In The Uae, Jassim Abubacker Ponnambathayil

Theses

Water flooding has been regarded as a well-known secondary oil recovery method. In the recent years, extensive research on crude oil, brine, and rock systems has acknowledged that the composition of the injected water can change wetting properties of the reservoir during a water flood in a promising way to improve oil recovery. Hence, injection of “smart water” with correct salinity and composition is considered as a tertiary recovery method. The mechanism behind wettability alteration that is promoted by smart water injection has been a topic of discussion in carbonate and sandstone formations. In this work, some key properties of …

Influence Of Strong Preformed Particle Gels On Low Permeable Formations In Mature Reservoirs, Mahmoud O. Elsharafi, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

In mature reservoirs, the success of preformed particle gel (PPG) treatment rests primarily on the ability of the PPG to reduce and/or plug the high permeable formations but not damage the low permeable formations. Static test models (filtration test model and pressure test model) were used to determine the effect of PPG on low permeable formations. This work used a strong preformed particle gel, Daqing (DQ) gel made by a Chinese company. The particle gel sizes were ranged from 30 to 120 mesh for this work. PPGs are sized in a millimeter or micrometer, which can absorb over a hundred …

Thawing Out: The Role Of The Arctic Council Service In A Melting Arctic, Taylor J. Enos

Pell Scholars and Senior Theses

With the changing natural and political climate of the Arctic, conflicts over resource extraction and navigation will become inevitable. Empowering an intergovernmental institution like the Arctic Council Service may be the only solution. This paper analyzes the importance and history of the Arctic as a political environment, which is prone to abuse in the very near future at the hands of Russia and the United States.

Laboratory Evaluation Of A Real-Time Coaxial Cable Casing Imager For Wellbore Integrity Monitoring, Yurong Li, Runar Nygaard, Baokai Cheng, Wenge Zhu, Hai Xiao

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Leakage is one of the major concerns in a geological carbon sequestration project due to the adverse environmental consequences. The main leakage risk of CO₂ through a thick, low permeable cap rock is identified to be along wells, especially in sedimentary basins that have a history of oil and gas exploration and production. To pursue a robust and cost-effective real-time monitoring technology for CO₂ leakage risk detection along the wellbore, a permanently downhole deployed coaxial cable casing imaging system is developed and tested for various deformation modes in laboratory in this paper. The casing imager consists of a …

Mitigation Of Wellbore Instability In Deviated Wells By Using Geomechanical Models And Mpd Technique, Husam Raad Abbood

Masters Theses

"During drilling operations for the E oilfield in the Mishrif formation in southern Iraq, stuck pipe presents a significant wellbore stability problem for deviated wells. In this study, two solutions are utilized to address this problem. The first approach is a 1-D Geomechanical model of the Mishrif formation compiled based on the state of stress and rock strength parameters. It is utilized to assess the contribution of borehole collapse leading to the stuck pipe problems. The results of this study show that wells characterized by stuck pipe are drilled along azimuths which promote wellbore collapse. Three different failure criteria, the …

Experimental Investigation Of Fracture Width Limitations Of Granular Lost Circulation Treatments, Mortadha Al-Saba, Runar Nygaard, Arild Saasen, Olav Magnar Nes

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Drilling fluid losses into fractured shales is a major challenge. Lost circulation treatments are widely applied to mitigate the losses; however, the effectiveness of these treatments is affected by different physical properties of the used lost circulation materials (LCM). This paper presents an experimental investigation to study the effect of LCM type, concentration, particle size distribution, temperature, and LCM shape on the formed seal integrity, with respect to differential pressure, at different fracture widths. The overall objective of this study is to address the effectiveness of LCM treatments in sealing fractured shales, with specific application to the over consolidated Barents …

Mathematical Scaling And Statistical Modeling Of Geopressured Geothermal Reservoirs, Esmail Ansari

LSU Doctoral Dissertations

The interest for developing geopressured-geothermal reservoirs along the US Gulf Coast is increasing for securing energy needs and reducing global warming. Identifying the most attractive candidate reservoirs for geothermal energy production requires quick and simple models. Analytical models are not always available and simulating each case individually is expensive. The use of scaling and statistical modeling is one approach to translate the output of a simulator into quick models with general applicability at all scales. The developed models can quickly estimate temperature and thermal energy recovery from the geopressured-geothermal reservoirs. These models can screen large databases of reservoirs to select …

High-Temperature, High-Pressure Viscosities And Densities Of Toluene, Aaron J. Rowane

Theses and Dissertations

High-temperature, high-pressure (HTHP) conditions are exemplified in ultra-deep petroleum reservoirs and can be exhibited within diesel engines. Accurate pure component hydrocarbon data is essential in understanding the overall behavior of petroleum and diesel fuel at these conditions. The present study focuses on the HTHP properties of toluene since this hydrocarbon is frequently used to increase the octane rating of gasoline and toluene occurs naturally in crude oil. In this thesis experimental densities and viscosity are presented to 535 K and 300 MPa extending the database of toluene viscosity data to higher temperature than previous studies. The data is correlated to …

Bioluminescent Magnetic Nanoparticles As Potential Imaging Agents For Mammalian Spermatozoa, Erick Salvador Vasquez, Jean M. Feugang, Scott T. Willard, Peter L. Ryan, Keisha B. Walters

Chemical and Materials Engineering Faculty Publications

Background: Nanoparticles have emerged as key materials for developing applications in nanomedicine, nanobiotechnology, bioimaging and theranostics. Existing bioimaging technologies include bioluminescent resonance energy transfer-conjugated quantum dots (BRET-QDs). Despite the current use of BRET-QDs for bioimaging, there are strong concerns about QD nanocomposites containing cadmium which exhibits potential cellular toxicity.

Results: In this study, bioluminescent composites comprised of magnetic nanoparticles and firefly luciferase (Photinus pyralis) are examined as potential light-emitting agents for imaging, detection, and tracking mammalian spermatozoa. Characterization was carried out using infrared spectroscopy, TEM and cryo-TEM imaging, and ζ-potential measurements to demonstrate the successful preparation of these nanocomposites. Binding …

Effect Of Reservoirs Heterogeneity On Injection Pressure And Placement Of Preformed Particle Gel For Conformance Control, Ze Wang

Masters Theses

"Preformed particle gels (PPG) have been successfully applied as a plugging agent for plugging fractures and then divert displacing fluid into poorly swept zones. However, PPG propagation and plugging mechanisms through open fractures have not been studied thoroughly.

This work investigated the influence of some factors (particle size, brine concentration, heterogeneity, and brine salinity) on gel injectivity, plugging performance for water flow through open fractures. Five-foot tubes were used to mimic open fractures. Three models were designed to conduct the work, including (1) single fracture with uniform fracture width, (2) single fracture with different widths, and (3) two parallel fractures …

Nitrogen Gas Flooding For Naturally Fractured Carbonate Reservoir: Visualisation Experiment And Numerical Simulation, Zhaojie Song, Jirui Hou, Zhongchun Liu, Fenglan Zhao, Shijun Huang, Yong Wang, Jieheng Wu, Baojun Bai

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Tahe Naturally Fractured Carbonate Reservoir has implemented nitrogen gas flooding since 2013, with daily oil production of 7580 bbls and oil recovery increment of 0.83% by the end of 2015. However, the presence of fractures significantly affects gas swept volume and production performance, so large amount of oil reserves is poorly flooded due to gas channeling through fractures. The fluid flow mechanisms in fractured models were discussed in order to improve field gas flooding efficiency. Based on the geological constrains of Tahe Oilfield, fractured models with different apertures were fabricated using acrylic glass to model carbonate matrix wettability and for …

Simulation Studies For Relative Importance Of Unconventional Reservoir Subgrid Scale Physics Parameters, Yaakoub Youssef El Khamra

LSU Doctoral Dissertations

In this endeavor we attempt to better understand gas transport in shale gas reservoirs, specifically the impact and effects of different physical phenomena. We start by documenting the nature of the reservoirs and the need for accurate modeling of various physical phenomena in multiple interconnected continua. The physical phenomena of interest include non-linear Forchheimer flow, Knudsen diffusion in the form of slip "Klinkenberg" flow and adsorption/desorption. The numerical methods used in the reservoir simulator are also introduced, along with a derivation of the main equations used. Various verification and validation results are compared against manufactured and analytical solutions and finally …

Development Of Single-Well Gas Assisted Gravity Drainage Process For Enhanced Oil Recovery, Bikash Deep Saikia

LSU Doctoral Dissertations

EOR application in prolific deepwater Gulf of Mexico (DGOM) reservoirs has remained a challenge. Exorbitant well cost (>200M$) precludes having extensive injection patterns and very characteristics of the reservoirs themselves are partly to blame for negligible EOR activity in DGOM. We have been able to develop and demonstrate a novel design in the form of Single Well – Gas Assisted Gravity Drainage (SW-GAGD) process, which is potentially cost effective, at the same time ensuring very high oil recoveries. In this design, a single well acts as an injector as well as a producer, thereby minimizing well cost. The efficacy …

Statistical Reservoir Characterization, Simulation, And Optimization Of Field Scale-Gas Assisted Gravity Drainage (Gagd) Process With Uncertainty Assessments, Watheq Jasim Mohammed Al-Mudhafar

LSU Doctoral Dissertations

Unlike the Continuous Gas Injection (CGI) and Water-Alternative Gas (WAG), the Gas Assisted Gravity Drainage (GAGD) process takes advantage of the natural segregation of reservoir fluids to provide gravity-stable oil displacement. The gas is injected through existing vertical wells to formulate a gas cap to allow oil and water drain down to the horizontal producer (s). Therefore, the GAGD process was implemented through immiscible and miscible injection modes to improve oil recovery in a sector of the main pay/upper sandstone member in the South Rumaila oil field, located in Iraq. A high-resolution geostatistical reservoir characterization model was constructed to model …

Modelling Hydraulic Fracturing Propagation In Heterogeneous Reservoirs Using Cohesive Zone Methods, Miguel Alejandro Gonzalez-Chavez

LSU Doctoral Dissertations

The recent success in exploiting low permeability shale reservoirs has heavily relied on hydraulic fracturing to produce hydrocarbons economically in disadvantaged reservoir conditions. Although horizontal drilling significantly increases the contact area between the wellbore and the reservoir, the objective of hydraulic fracturing is set on creating further expanded conductive flow paths into the reservoir. This research uses cohesive zone method to numerically simulate hydraulic fracture propagation in the presence of natural fractures in two- and three-dimensional model. The Cohesive element approach limits fracture propagation to some predefined paths. However, in highly fractured formations since hydraulic fractures are growing through a …

Expandable Proppants For Hydraulic Fracturing, Livio Yang Santos

LSU Master's Theses

Hydraulic fracturing is recognized as the primary technique to achieve economic oil and gas production from low permeability reservoirs like shale and tight-sand formations. One of the main challenges facing the oil and gas industry is maintaining the proppant functionality in the subsurface where replacement of proppant is only possible by expensive refracturing operations. Proppant crushing and proppant embedment have posed challenges for sustainable production from stimulated wells especially in soft and deep formations like Haynesville Shales. Experimental measurements show the strong impact of proppant stress and proppant embedment on reducing fracture conductivity. In this work, we introduce a new …

Design And Development Of A High-Temperature High-Pressure Rolling Ball Viscometer/Densimeter And Evaluation Of Star Polymer-Solvent Mixtures, Matthew Stanton Newkirk

Theses and Dissertations

Modern automotive applications such as transmission clutch plates, combustion chambers, diesel fuel injector tips, and axle gears and friction plates operate at temperatures that can exceed 250°C and pressures of 40,000 psia. Industrial practice is to add homopolymers and copolymers to base oils to modify bulk fluid viscosity and frictional properties for these demanding applications. However, designing polymeric additives for lubricants and predicting their performance is limited by the lack of available high-temperature high-pressure (HTHP) viscosity and density data needed to test contemporary lubricity models. Thus, a major objective of this thesis is the design, development, and commissioning of a …

An Integrated Completion And Reservoir Modeling Methodology For Horizontal Shale Wells: A Montney Formation Example, Rashid S. Kassim, Larry K. Britt, Shari Dunn-Norman, Bryan Lang

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

The Montney Formation is one of the largest unconventional resources in North America covering from southwestern Alberta to northeast British Columbia. The Montney Formation has natural gas, natural gas liquids (NGL) and oil from conventional and unconventional reservoirs. The first multiple fractured horizontal well (MFHW) was drilled in 2005. However, since the first MFHW, different methods were proposed to optimize completion designs in the Montney Formation. Some of the optimized completions utilized the "operational effectiveness" of high-rate slick-water fracture designs while other designs utilized energized fracturing fluids. What has been missing was an integrated methodology that utilizes all available data …

Wetting Kinetics In Forced Spreading, Amer Mohammad Al-Shareef

Doctoral Dissertations

"Under dynamic conditions, the dynamic contact angle (the angle that the liquid makes with the solid) of a liquid on a solid surface varies dramatically with substrate velocity from its equilibrium value. Experimental data of the dynamic contact angles for polydimethylsiloxane (PDMS or silicone oil) under air on a glass substrate coated with teflon, for water under PDMS, for solutions of the polymer polyethylene oxide (PEO) under air, for solutions of PEO under PDMS, were obtained to simulate and understand the systems of brine or brine containing a polymer displacing viscous crude. A variety of solid substrates were used other …

A Comprehensive Study Of Lost Circulation With Application In The South Rumaila Field, Iraq, Abo Taleb Tuama Al-Hameedi

Masters Theses

“Drilling mud losses and problems associated with lost circulation while drilling account for a major expense in drilling oil and gas wells. By industry estimates, more than 2 billion USD is spent annually to combat and mitigate this problem (Ali et al., 2015).

The South Rumaila field in Iraq is one of the largest oilfields in the world. Wells drilled in this field are highly susceptible to lost circulation problems when drilling through the Dammam, Hartha and Shuaiba formations. Lost circulation events range from seepage losses to complete loss of the borehole and are a critical issue in field development. …