Petroleum Engineering Commons^™

Core-Scale Study Of Miscible Co2 Foam–Oil Interactions, Kuvonchbek Abdirakhmonov

Theses

Foam is currently the most effective means for gas mobility control in a variety of geo-energy applications, including enhanced oil recovery (EOR), carbon capture, utilization and storage (CCUS), and aquifer/soil remediation. This study investigates the mobility control of miscible CO₂ foam in the presence of oil.

The primary objective is to quantify the impact of oil on CO₂ foam behavior under miscible conditions, specifically examining foam stability, strength, and flow regimes as influenced by oil composition and reservoir permeability. While most oils destabilize foam, few studies explore the coarsening mechanisms of CO₂ foam in the presence of miscible oils, which …

Investigation And Prediction Of Excessive Water Production In Bottom Water-Drive Naturally Fractured Reservoirs Using Machine And Deep Learning, Sami Abderraouf Belkhir

Theses

Naturally Fractured Reservoirs (NFRs) are characterized by dual-porosity and dual-permeability systems, posing significant challenges in managing water production due to highly conductive fracture networks that facilitate rapid water migration from bottom aquifers, often bypassing oil stored in the matrix, thus resulting in early water breakthrough and water channeling phenomena. The main objective of this thesis is to develop and validate deep learning and machine learning models to predict water production, water breakthrough time (tbt), and ultimate water cut (WCult) in NFRs, thereby enabling more effective reservoir management strategies. This work also aims to evaluate the sensitivity of water behavior to …

Experimental Evaluation Of Novel Nano Polymer Hybrid Enhanced Oil Recovery In Carbonate Reservoir, Altamish Ahmed Pakeer

Theses

Innovative enhanced oil recovery (EOR) strategies are needed to unlock additional reserves in heterogeneous, oil-wet carbonate reservoirs. This study evaluates hybrid nano-polymer flooding by integrating silica nanoparticles (SiO₂) and single-walled carbon nanotubes (CNT) with novel HPAM polymers (Sav10 and Sav10 VHM) to optimize wettability alteration, rheological parameters, and recovery mechanisms.

A comprehensive experimental approach was employed, where rheological tests assessed viscosity enhancement under varying shear conditions, and wettability alteration was quantified via contact angle measurements using HPAM-SiO₂, HPAM-CNT, Sav10 VHM-SiO₂, and Sav10 VHM-CNT systems. Core floods were performed in three consecutive phases; waterflooding (baseline), standalone nanoparticle flooding, and hybrid nano-polymer …

Data-Driven Machine Learning Applications For Predictive Modeling Of Petrochemical And Ecofriendly Systems, Noora Saleh Al Mansoori

Theses

Traditional experimental approaches in industrial processes, such as Fourier Transform Infrared Spectroscopy (FTIR) spectroscopy, thermogravimetric analysis (TGA), and well-drilling operations, are often constrained by time, cost, and operational limitations. This research explores the application of data-driven Machine Learning (ML)-based predictive modeling to improve efficiency and reduce dependency on resource-intensive experimentation. The study develops ML models for three distinct processes: FTIR intensity prediction of bitumen thermal cracking products, thermal degradation of Medium-Density Fibreboard (MDF) using TGA data, and Rate of Penetration (ROP) prediction in petrochemical industry. Six algorithms: Linear Regression (LinReg), Partial Least Squares Regression (PLSR), Support Vector Regression (SVR), Gradient …

Utilizing Date Fruit Pomace As A Corrosion Green Inhibitor For Non Ferrous Alloys, Sardor Rustam Odilov

Theses

This thesis explores a novel green corrosion inhibitor derived from date fruit pomace extract (DFPE) for the protection of aluminum alloy 3003 in highly corrosive environments, specifically hydrochloric acid (HCl) and natural seawater. The central aim is to promote the sustainable reuse of agro-waste as an effective and eco-friendly alternative to conventional toxic inhibitors, aligning with environmental and industrial safety goals.

A comprehensive methodology was employed, including Soxhlet extraction (using both non-polar n-hexane and polar methanol-water solvents), rotary evaporation, and FTIR analysis to identify the active functional groups responsible for inhibition. Corrosion behavior was systematically evaluated using both mechanical (weight …

A Computational Investigation Into Thermo-Kinetic Parameters Governing The Decomposition Of Bio-Oil Model Compounds, Ali Huseein Aljefri

Theses

Among notable products from thermal degradation of biomass are simple oxygen-containing aromatics. These compounds typically appear in high loads in collected bio-oil derived from biomass. As such, it is important to comprehend the decomposition chemistry of this category of compounds. This thesis takes on board a general approach to report thermo-kinetic parameters that govern decomposition of a selected set of bio-oil model compounds in two distinct systems: firstly radical-derived pathways in the gas phase and secondly thermal degradation in their condensed media. The first is attained through accurate density functional calculations while the second is accomplished through the use of …

Development Of Tio2/Nh2-Mil-125 Nanocomposite For The Removal Of Ciprofloxacin Under Induced Solar Irradiation, Bilkis Mojisola Ajiwokewu

Theses

This research focuses on the development and application of Metal-Organic Frameworks (MOFs)-based nanocomposites for the photocatalytic removal of pharmaceutical contaminants, with a specific emphasis on ciprofloxacin (CIP). The photocatalytic degradation of CIP was investigated using as-synthesized photocatalysts of TiO₂ nanowires (TiO₂NWs), bare MOF of NH₂-MIL-125, TiO₂NW/NH₂-MIL-125 composite, and Lanthanum (La)-doped composite. Intriguingly, the TiO₂NW/NH₂-MIL-125 composite exhibited the highest efficiency, achieving a photodegradation rate of 0.0111 min-1, surpassing the independent performances of bare MOF of NH₂-MIL-125 and TiO₂NW. The observed efficiency was attributed to …

Thermo-Kinetic Parameters Governing Decomposition Of Amino Acids: A Computational Study, Mubarak Taleb Alkwradi

Theses

Amino acid model compounds are important nitrogenated species that in various categories of biomass. These compounds exhibit unique fragmentation pathways because of their adjacent amino and hydroxyl groups. Comprehending the decomposition chemistry of amino acids is essential to reduce harmful nitrogen emissions during biomass thermal treatment. This research reports the kinetic and thermodynamic properties of amino acids, and sulfur-containing amino acid, based on accurate density functional theory calculations coupled with kinetic modelling. The first part of the thesis provides comprehensive thermochemical parameters for the complete set of amino acids in the gas phase. The optimized geometries of amino acid compounds …

Selective Production Of Levoglucosan (Lg) From Pyrolysis Of Date Pits And Its Catalytic Transformation Into Transportation Fuels, Ala Hamid Higazi

Theses

Levoglucosan (LG) or (1,6-anhydro-β-D-glucopyranose) signifies important sugar derivatives produces in appreciable quantities from thermochemical and biochemical degradation of biomass. It is often regarded as an important platform chemical for the synthesis of value-added products, most notably styrene and furans. The work in this thesis entails two broad aims; to produce LG from pyrolysis of date pits; and then convert the LG into transportation fuels through a hydrodeoxygenation (HDO) reaction. The particular choice of date pits stems from its local relative abundance as a waste biomass. Aiming to further improve the yield of levoglucosan yields from pyrolysis of date pits, pre-treatment …

Development Of Unsaturated Polyester Resin Mortar Utilizing Industrial Wastes, Fatema Ahmed Alahmed

Theses

In recent years, polymer mortar (PM) has played a crucial role in the modern construction industry. It is gaining recognition as an effective and quick repair material in construction applications because it has several benefits over traditional Portland cement concrete. Various types of polymer binders, such as unsaturated polyester resin (UPR), have been used in these materials owing to their low cost, excellent strength, high workability, and rapid curing. This study investigates the feasibility of reutilizing locally available waste in the production of UPR-based polymer mortar, which facilitates the development of mortars with less environmental impact. In this study, the …

Development Of Popcorn Thermal Insulation Panels, Yonis Hussein Mohamud

Theses

The research and development of sustainable and renewable materials that can take the place of conventional plastics derived from petroleum has attracted increasing attention in recent years. Polylactic acid (PLA) and Polyhydroxy butyrate (PHB) are viable alternatives biopolymers due to their biodegradability. Also, the enhancement of material properties can be achieved through the incorporation of fillers. In this study, the utilization of popcorn in developing of insulation materials has been employed in two distinct methodologies. The first involves the coating of popcorn with varying percentages of PLA using the solvent casting method, while the second involves the integration of popcorn …

Selection Of Natural Surfactants For Possible Use In Improving Oil Recovery Of Carbonate Oil Reservoirs, Hiba Hachem Limam

Theses

Middle East petroleum industry is currently searching for the most suitable enhanced oil technique to improve the oil recovery from local oil reservoirs. The biggest challenge for the application of enhanced oil recovery (EOR) in the Middle East is the harsh environment (high salinity and temperature). Surfactant (synthetic or natural) is one of the EOR major players considered for application in the Middle East. However, synthetic surfactants have several drawbacks, such as economically unattractive and environmental impacts. This study investigated the possible use of natural surfactant extracted from the leaves of three types of plants, namely Aloe Vera, Tetraena qatarensis, …

Upgrading Biomass To Bio-Oil: Catalytic Hydrodeoxygenation And Pyrolysis Of Vanillin And Anisole Biomass Model Compounds, Ahmad J. Yaghi

Theses

The purpose of this project is to investigate capacity of selected formulations of catalysts toward the hydrodeoxygenation (HDO) of biomass model compounds in the gas phase with the underlying aim to produce hydrocarbon cuts that can be directly used as transportation fuels. The first part of this project is to devoted to illustrate procedures for the synthesis of potent (HDO) catalysts. Synthesized catalysts encompass nickel (Ni), cobalt (Co) and palladium (Pd) supported on zeolite, cerium oxide (CeO₂) or alumina (Al₂O₃). Various characterization techniques such as X-ray Diffraction (XRD), Temperature Programmed Reduction (TPR) were deployed …

Novel Investigation Of Catalytic Hydrogenation And Oxidation Of 1,3-Butadiene, Ali M. Alabedkhalil

Theses

The hydrogenation of 1,3 Butadiene (BD) is an important industrial process that is generally used to generate butene, which is a key feedstock to produce a variety of chemicals such as polymers, plastic, and synthetic rubber. This process involves reacting BD with hydrogen using different metallic Ni-based catalysts. In this study, Ni/Al₂O₃ and Ni/Nb₂O5 catalysts were used and investigated to perform the hydrogenation reaction because of their commercial availability, effective hydrogenation activity, and affordability compared to Platinum Group Metal (PGM) catalysts.

The catalytic reactions were conducted using a quartz tube reactor between a temperature range …

Using Switchable Solvents For Enhanced Biodiesel Production, Eyad Abdel Rahman Sowan

Theses

This thesis presents a sustainable approach to biodiesel production using in-situ technology for direct conversion of microalgae-to-biodiesel. The proposed method operates on wet, untreated microalgae, thereby eliminating the cost/energy intensive drying and cell disruption steps. Owing to their favorable properties, the use of enzymes, specifically lipase, as a catalyst for the process was suggested over acid/base catalysts. However, the high cost of the enzyme necessitates its reuse at sustained activity for the process to be economically feasible. The use of non-toxic green solvents, such as switchable solvents, as an alternative to conventional organic solvents was a significant challenge for the …

Biodegradable Heat Insulation Composites Based On Poly(Β-Hydroxybutyrate) And Date Palm Wood, Amal Ibrahim Mlhem

Theses

Residential buildings contribute the most to energy consumption. It was found that energy savings of 20% can be achieved through the thermal insulation of residential buildings in the United Arab Emirates. For this reason, research has been conducted in the field of sustainable thermal insulation materials. Wood-Plastic Composites (WPC) are a relatively new generation of biocomposites and are particularly suitable for construction and building applications, which offers high thermal and acoustic insulation properties., reducing carbon emissions and decreasing negative impacts on the environment due to their biodegradability, sustainability, renewability, and recyclability. The first part of this study investigated the thermal …

Utilizing Date Pits In Microencapsulation: Effect Of Different Variations On Probiotic Survivability Under In Vitro Digestion, Asmaa Samir Al Hamayda

Theses

This work deals with the medicinal use of date pit powder, which turns it from a waste product to a useful stabilizer for the release of beneficial probiotics in the human intestine. The main objective of this work is to encapsulate probiotics with date pit beads and their subsequent release in the human intestine. The beads were formed using gravitational dripping technique, while INFOGEST protocol was used to test the digested beads and the release of viable probiotic cells. For the three date varieties Raziz, Naghal and Khadrawy, it was found that 0.1 g of date pit powder per 0.2 …

Fabrication And Characterization Of Graphene Oxide-Based High-Density Polyethylene / Polypropylene Nanocomposites For Biomedical Applications, Albaina Ali Aldhaheri

Theses

Polymeric nanocomposites have recently become one of the most essential sought-after materials for biomedical applications. Among many others, High-Density Polyethylene (HDPE) is being widely used as a bearing material for the artificial hip and knee joints. However, the weak surface properties of HDPE limit the total artificial hip joints’ survival chances. The addition of polypropylene (PP) improves the surface properties of HDPE composites along with their thermal, chemical, and mechanical properties which are crucial in biomedical applications. Moreover, PP can be easily blended with polyethylene (PE) as it has an almost similar chemical resistance to PE. However, PP is more …

Effects Of Wettability, Lithology, And Permeability On The Optimum Slug Size Of Low Salinity Water Flooding In Carbonates: An Experimental Approach, Hala Khaled Hasan Alshadafan

Theses

Low salinity water flooding has attracted academic and industry communities due to its relatively simple and applicable technology. One of the drawbacks of applying the IOR/EOR technique is the lack of the availability of low salinity water in large quantities at the reasonable cost required for a technically and environmentally successful project. To overcome this problem, the industry proposed to use produced water/sea water after dilution, and reverse osmosis filter technology to achieve the required salinity. Both techniques are quite costly and might hinder the project's economic success. Low salinity water as slug size followed by high salinity water was …

Desalination Waste Revitalization Using Carbon Capture: Process Optimization Using Machine Learning, Ahmed Mohamed Elsayed

Theses

Over the next five to ten years, desalination will play an ever-important role in our society. Developing nations will look at desalination from the point of water scarcity, while developed nations will consider the perspective of the Water-Energy-Food nexus. With current technology, for every liter of freshwater produced, one and a half liters is thrown away as waste. This body of research proposes to employ chemical precipitation in ammoniated brine solutions, that have reasonably high ionic concentrations. CO2 absorption in Bubble Column Reactors can reduce sodium ions by precipitating NaHCO3. Also, the absorbed CO2 can reduce chloride ions and induce …

Possible Storage Of Co₂ In Saline Aquifer: Storage Factor Estimation, Sarah Abdul Aziz Al-Tamimi

Theses

The objective of this study is to perform laboratory measurements and a CO₂ underground storage study to cover the knowledge gap on CO₂-Brine relative permeability and assess various variables on the storage of CO₂ in a selected aquifer. Several factors that affect CO₂ storage have been discussed in the literature. These include both macroscopic and microscopic displacement efficiency of brine as a function of CO₂ pore volume injected. It is clear from the literature that there is still more work needed to investigate the effect of various variables such as formation temperature, brine viscosity, and the possible presence of free …

Developing A New Formula For Predicting Oil Recovery Factor In Water Flooded-Heterogeneous Reservoirs, Mohamed Khaled Aljifri

Theses

In this work, two sets of empirical correlations were developed for predicting the recovery factor (RF) in water-flooded layered oil reservoirs. The first set of these correlations encompasses four key parameters believed to have a significant impact on waterflooding performance, namely, reservoir heterogeneity (permeability variation coefficient), injected water viscosity, permeability anisotropy (ratio of vertical permeability to horizontal permeability), and water injection rate. This first set consists of two expanded forms, one for predicting the RF at water breakthrough time (BT) and the other for predicting the RF at the end of the project (EOP). Out of the aforementioned four key …

Optimization Of A New Array Noise Tool; Analysis & Interpretation Of Case Studies Of Down- Hole Leak Detection, Moustafa Mahmoud Hassan Ismail

Theses

This thesis is concerned with the optimization and analysis of new array noise tools. Various lab and field case studies are analyzed to test the capabilities and determine the optimum operating conditions of the new tool for leak detection purposes. The purpose of this study is to optimize the logging procedure of real-time array noise tool, selecting adequate gain parameters and frequency band in the processing phase, and to analyze the data acquired through multiple labs and field tests. The study methodology involved the following steps:

1. Performing lab and field tests for the tool in a range of different …

Experimental Study Of Low Salinity Water Flooding And Fracturing Effects In Low Permeability Carbonate Reservoir, Benny Arianto Harahap

Theses

In past decades, there were numerous research works demonstrated that salinity alteration of injected water could enhance the oil recovery. Low salinity water (LSW) injection is a type of Enhanced Oil Recovery (EOR) method, which attracts the industrial, and researchers because of its simplicity to use the implications,

Environment-friendly nature, and less cost. In addition to, hydraulic fracturing, also known as hydraulic stimulation, is another EOR method that improves hydrocarbon flow by creating fractures in the Low Permeability Formation (LPF) that connects the reservoir and wellbore. Fractures will increase the permeability of reservoir and give the flow path for hydrocarbon …

Oil Recovery By Surfactant Flooding; Sensitivity Analysis To Technical Parameters And Economic Analysis, Hadel Mohsen Moustafa

Theses

Various enhanced oil recovery methods including miscible gas injection, chemical, thermal and other methods are applied at the third phase of production after the primary and secondary recovery have been exhausted. Surfactant flooding is one of the chemical methods that is capable of recovering more oil by decreasing the IFT and/or wettability alteration.This piece of work aims to asses and select the development options using surfactant process that maximize oil recovery for a synthetic reservoir model by optimizing technical and economic analysis.

Reservoir simulation study using ECLIPSE 100 was used to study the different development options of surfactant flooding applied …

Oil Recovery By Polymer Flooding; Sensitivity Analysis To Technical Parameters, Rana Osama Fahmi Saqer

Theses

Numerous enhanced oil recovery techniques including miscible gas injection, chemical, thermal and other methods are applied at the third phase of production after both primary and secondary recovery have been exhausted. Polymer flooding is one of the chemical methods that recover more oil by decreasing the mobility of the system; by increasing the viscosity of the injected water that results in an improvement in the volumetric sweep efficiency.

The objective of this work is to asses and select the development options using polymer process that maximize oil recovery for a synthetic reservoir model where technical parameters are optimized thoroughly.

Reservoir …

Oil Recovery By Flooding; Sensitivity Analysis To Technical Parameters, Rana Osama Fahmi Saqer

Theses

Numerous enhanced oil recovery techniques including miscible gas injection, chemical, thermal and other methods are applied at the third phase of production after both primary and secondary recovery have been exhausted. Polymer flooding is one of the chemical methods that recover more oil by decreasing the mobility of the system; by increasing the viscosity of the injected water that results in an improvement in the volumetric sweep efficiency.

The objective of this work is to asses and select the development options using polymer process that maximize oil recovery for a synthetic reservoir model where technical parameters are optimized thoroughly.

Reservoir …

Contact Angle And Ift Measurements Of Smart Water At Elevated Temperatures And Pressures For Evaluating Wettability In A Selected Carbonate Reservoir In The Uae, Jassim Abubacker Ponnambathayil

Theses

Water flooding has been regarded as a well-known secondary oil recovery method. In the recent years, extensive research on crude oil, brine, and rock systems has acknowledged that the composition of the injected water can change wetting properties of the reservoir during a water flood in a promising way to improve oil recovery. Hence, injection of “smart water” with correct salinity and composition is considered as a tertiary recovery method. The mechanism behind wettability alteration that is promoted by smart water injection has been a topic of discussion in carbonate and sandstone formations. In this work, some key properties of …

Enzymatic Production Of Biodiesel From Fats Extracted From Lamb Meat Using Supercritical Co2, Hanifa Easa Taher

Theses

Due to the reduction in fossil fuel reserves and associated environmental impacts from using petroleum fuels, biodiesel has been presented as a feasible alternative because it is sustainable and environmentally friendly. In this study, it is proposed to investigate the feasibility of enzymatic production of biodiesel from waste animal fats using supercritical fluid technology for the extraction and reaction. The operating conditions that resulted in the optimum extraction and biodiesel production yield were identified. To the best of my knowledge of the investigators, the waste animal fat extracted by supercritical CO₂ (SC-CO₂) for the production of biodiesel …

Pvt Study Of Selected Uae Reservoir Fluids, Rashid Sher Mohammad

Theses

Phase behavior modeling in crude oil includes prediction of thermodynamic properties (such as saturation pressure, density, viscosity, thermal conductivity, etc.) for the vapor and liquid phases. The aim of phase behavior modeling is to establish the accuracy and reliability of the developed equation of state model to predict various other fluid phase behavior properties at high pressure and temperature conditions.

In the first part of this work, a new and reliable phase behavior apparatus designed in Brazil was used for the two-stage recombination process and phase behavior measurements. The recombination of the surface sample fluids (first-stage separator gas and stock-tank …