Petroleum Engineering Commons^™

Development Of Single-Well Gas Assisted Gravity Drainage Process For Enhanced Oil Recovery, Bikash Deep Saikia

LSU Doctoral Dissertations

EOR application in prolific deepwater Gulf of Mexico (DGOM) reservoirs has remained a challenge. Exorbitant well cost (>200M$) precludes having extensive injection patterns and very characteristics of the reservoirs themselves are partly to blame for negligible EOR activity in DGOM. We have been able to develop and demonstrate a novel design in the form of Single Well – Gas Assisted Gravity Drainage (SW-GAGD) process, which is potentially cost effective, at the same time ensuring very high oil recoveries. In this design, a single well acts as an injector as well as a producer, thereby minimizing well cost. The efficacy …

Statistical Reservoir Characterization, Simulation, And Optimization Of Field Scale-Gas Assisted Gravity Drainage (Gagd) Process With Uncertainty Assessments, Watheq Jasim Mohammed Al-Mudhafar

LSU Doctoral Dissertations

Unlike the Continuous Gas Injection (CGI) and Water-Alternative Gas (WAG), the Gas Assisted Gravity Drainage (GAGD) process takes advantage of the natural segregation of reservoir fluids to provide gravity-stable oil displacement. The gas is injected through existing vertical wells to formulate a gas cap to allow oil and water drain down to the horizontal producer (s). Therefore, the GAGD process was implemented through immiscible and miscible injection modes to improve oil recovery in a sector of the main pay/upper sandstone member in the South Rumaila oil field, located in Iraq. A high-resolution geostatistical reservoir characterization model was constructed to model …

Modelling Hydraulic Fracturing Propagation In Heterogeneous Reservoirs Using Cohesive Zone Methods, Miguel Alejandro Gonzalez-Chavez

LSU Doctoral Dissertations

The recent success in exploiting low permeability shale reservoirs has heavily relied on hydraulic fracturing to produce hydrocarbons economically in disadvantaged reservoir conditions. Although horizontal drilling significantly increases the contact area between the wellbore and the reservoir, the objective of hydraulic fracturing is set on creating further expanded conductive flow paths into the reservoir. This research uses cohesive zone method to numerically simulate hydraulic fracture propagation in the presence of natural fractures in two- and three-dimensional model. The Cohesive element approach limits fracture propagation to some predefined paths. However, in highly fractured formations since hydraulic fractures are growing through a …

Application Of The Variational Fracture Model To Hydraulic Fracturing In Poroelastic Media, Chukwudi Chukwudozie

LSU Doctoral Dissertations

Hydraulic fracturing has persisted through the use of simple numerical models to describe fracture geometry and propagation. Field tests provide evidence of interaction and merging of multiple fractures, complex fracture geometry and propagation paths. These complicated behaviors suggest that the simple models are incapable of serving as predictive tools for treatment designs. In addition, other commonly used models are designed without considering poroelastic effects even though a propagating hydraulic fracture induces deformation of the surrounding porous media. A rigorous hydraulic fracturing model capable of reproducing realistic fracture behaviors should couple rock deformation, fracture propagation and fluid flow in the both …

Impacts Of Rock-Brine Interactions On Petrophysical Properties Of A Sandstone Reservoir, Utilizing Geochemical And Pore Network Modeling, Masoud Safari-Zanjani

LSU Doctoral Dissertations

Unfavorable consequences of geochemical reactions, such as calcite and silica scaling, in geothermal power plant surface facilities have been discussed in many recent studies. However, the impact of brine-rock interactions related to geothermal projects on reservoir properties has not been addressed fully. In this study, interactions between geothermal fluid and reservoir rocks in two fields located in Vermilion Parish, LA, and Chocolate Bayou, TX, are examined using geochemical modeling. The studied reservoir belongs to the Frio formation. In the geochemical models, the brine is cooled down to the estimated output temperature of a geothermal heat exchanger and re-equilibrated. Then, brine-rock …

Application Of The Finite Element Method To Solve Coupled Multiphysics Problems For Subsurface Energy Extraction, Milad Ahmadi

LSU Doctoral Dissertations

Fractures are a source of extra compliance in the rock mass. Fracture compliance can estimate the fracture roughness and the type of fluid filling the fracture. The focus of this research study in chapter 2 is to illustrate how the compliance ratio of rough fractures can diverge from the compliance ratio of smooth fractures. The imperfect interface of the fracture is modeled with saw-tooth-like structures. The defined saw-tooth-like structures of contact asperities impose an in-plane asymmetry in the shear direction. The compliance ratio of the rough fracture is larger than the compliance ratio of the smooth fracture. Interlocking and riding …

Design And Analysis Of Geothermal Wellbore Energy Conversion System Working On Zero Mass Withdrawal Principle, Ildar Akhmadullin

LSU Doctoral Dissertations

This project is sponsored by the Department of Energy of the United States and dedicated to development of electricity production from the low-enthalpy geothermal reservoirs. The prime interest are reservoirs that are characterized by low temperature of heat source located in deep saline aquifers with high permeable rock. Usually energy production from these resources are not economical by using a conventional binary power plant approach. The presented PhD work is a study of a new system that utilizes a single-well technology and working on supercritical power cycle (PC). The wellbore energy conversion system is operating with Zero Mass Withdrawal (ZMW) …

Deepwater Gulf Of Mexico Oil Spill Scenarios Development And Their Associated Risk Assessment, Muhammad Zulqarnain

LSU Doctoral Dissertations

World’s growing energy demand has pushed oil companies to explore and produce hydrocarbons in complex and technologically challenging deepwater environments. These difficult and complex operations involve the risk of major accidents as well, demonstrated by disasters such as the explosion and fire on the UK production platform Piper Alpha and capsizing of the Deepwater Horizon rig in the Gulf of Mexico (GoM). Accidents cause death, suffering, pollution of the environment, disruption of business and bad reputation to oil industry. A quantitative risk analysis technique has been used in this study to identify and categorize risk associated with different life phases …

Modeling Of Foam Flow In Porous Media For Subsurface Environmental Remediation, Seungjun Lee

LSU Doctoral Dissertations

Among numerous foam applications in a wide range of disciplines, foam flow in porous media has been spotlighted for improved/enhanced oil recovery processes in petroleum-bearing geological formations and shallow subsurface in-situ NAPL (non-aqueous phase liquid) environmental remediation in contaminated soils and aquifers. In those applications, foams are known to reduce the mobility of gas phase by increasing effective gas viscosity and improve sweep efficiency by mitigating subsurface heterogeneity. This study investigates how surfactant/foam process works fundamentally for environmental remediation purpose by using MoC (Method of Characteristics) based foam modeling and simulation techniques. It consists of two main parts: Part 1, …

Multiscale Estimation Of Inertial Effects For Frac-Pack Completed Gas Reservoirs, Sultan Anbar

LSU Doctoral Dissertations

Accurate estimation of production from frac-pack completed gas wells requires reliable estimation of flow properties from reservoir rocks and proppants. This study is composed of three parts: core-scale, pore-scale and reservoir-scale analyses of this problem. In the core-scale analysis, simultaneous estimation of permeability, non-Darcy, and Klinkenberg coefficients of reservoir rock is conducted from steady-state and pulse-decay experiments. Confidence intervals of the estimated parameters are determined from the Bootstrap method. The duration of pulse-decay experiments has a large impact on confidence intervals; therefore, correlations are developed to estimate the experimental duration for both 1-tank and 2-tank set-ups from the core properties …

Continuous Reservoir Modeling Updating By Integrating Experimental Data Using An Ensemble Kalman Filter, Ting Sun

LSU Doctoral Dissertations

The continuous researvoir model updating is widely used to calibrate reservoir simulation models to production data, but many challenges remain. First, few real field data are available to test the new history matching method, and most of the data sets are synthetic cases. Second, computational cost may be high when using non-Gaussian priors or nonlinear models. Third, with large complex models, the simulation runs and history matching method require huge memory allocations. This dissertation achieves a continuous reservoir model updating workflow with a meter-scale , two-phase flow experiment. Both production and seismic data are collected in the experiment. Because the …

Poroelastic Inhomogeneities: Applications In Reservoir Geomechanics, Houman Bedayat

LSU Doctoral Dissertations

The scarce amount of conventional hydrocarbon reservoirs and increase of fuel consumption in the world have made production from unconventional hydrocarbon resources inevitable. Because of the low permeability of unconventional formations, fractures are the main paths for the fluid to flow. Therefore, detailed knowledge of the size, orientation, and permeability of the fracture systems are essential for reservoir engineers. Permeability of the fractures is function of their volume and opening, and stress and fluid pore pressure distribution in the formation. Since reservoir pressure may change over the production life of the reservoir, studying stress redistribution and mechanical behavior of the …

Development Of A Framework For Scaling Surfactant Enhanced Co₂ Flooding From Laboratory Scale To Field Implementation, Gbolahan I. Afonja

LSU Doctoral Dissertations

The efficiency of the use of CO2 as a displacement fluid in oil recovery is hampered by the existence of an unfavorable mobility ratio that is caused by the large difference in viscosity between the injected fluid (CO2) and the reservoir fluids. This viscosity contrast results in early CO2 breakthrough, viscous fingering, gas channeling, and consequently, the inability of CO2 to effectively contact much of the reservoir and the oil it contains. Improvement of sweep efficiency and mobility control in CO2 injection require solutions to these problems. The use of surfactants and other chemical means for mobility control has been …

A Feasibility Study Of Multi-Functional Wells For Water Coning Control And Disposal, Lu Jin

LSU Doctoral Dissertations

Although water coning is well understood, it is difficult to control in field operations resulting in low recovery and large volumes of waste produced water. A solution - proposed here - is a multi-functional well with the in-situ bottom water drainage and injection installations - Downhole Water Loop (DWL). Theoretically, DWL greatly improves well performance (for example, a two-fold increase of DWL well’s water drainage rate would increase the critical (water-free) oil rate by 80%). However, DWL has practical limitations that must be quantified for actual well design. The objective of this work is to: (1) find maximum water drainage …

Multi-Scale Modeling Of Inertial Flows Through Propped Fractures, Ali Takbiri Borujeni

LSU Doctoral Dissertations

Non-Darcy flows are expected to be ubiquitous in near wellbore regions, completions, and in hydraulic fractures of high productivity gas wells. Further, the prevailing dynamic effective stress in the near wellbore region is expected to be an influencing factor for the completion conductivity and non-Darcy flow behavior in it. In other words, the properties (fracture permeability and β-factor) can vary with the time and location in the reservoir (especially in regions close to the wellbore). Using constant values based on empirical correlations for reservoirs/completions properties can lead to erroneous cumulative productivity predictions. With the recent advances in the imaging technology, …

Analytical Modeling And Diagnosis Of Penetration Rate Performance Of Pdc Bits, Reza Rahmani

LSU Doctoral Dissertations

The high cost of drilling deep (15000+ ft) wells, due to slow rate of penetration (ROP) at depth, has severely limited the utilization and economic significance of deep hydrocarbon resources. The overall objective of this study was to obtain a better understanding of the major cause(s) of slow ROP in deep drilling. An analysis of field data demonstrated the impact of the problem and identified shale and limestone as the primary lithologies where slow ROP occurs at depth. Previous researchers have concluded that interactions between rock, drilling fluid, cuttings, and the bit control ROP. More specifically, several researchers have concluded …

Emergence Of Delamination Fractures Around Casing And Its Stability, Wei Wang

LSU Doctoral Dissertations

The cement sheath failures and nearby wellbore failures may lead to upward flow of drilling fluid or formation fluid, which may have significantly adverse consequences like loss of reserve and environmental hazards. In order to maintain wellbore integrity in the long term, it is expedient to examine the causes of failures around the wellbore and propose suitable numerical models to predict annulus cracks around the casing. The complex failure behavior of cement/rock interfaces observed in the laboratory experiments does not look like the behavior of linear or simple nonlinear mechanical interfaces. Cohesive zone method (CZM) with BK-form bilinear traction separation …

A Large Scale Network Model To Obtain Interwell Formation Characteristics, Seyedmohammadamin Gherabati

LSU Doctoral Dissertations

Limited data availability and poor data quality make it difficult to characterize many reservoirs. For reservoirs that have undergone waterflooding, production and injection data are a reliable source of information from which injector-to-producer connections can be inferred. In this research, we use well locations, injection and production rate data and well fractional flow values to develop a reservoir-scale network model. A Voronoi mesh divides the reservoir into a number of node volumes each of which contains a well. Bonds connect each of the nodes with conductance values that must be inferred from the rate data. An inverse problem is formulated …

Experimental And Modeling Study Of Foam Flow In Pipes With Two Foam-Flow Regimes, Ali Reza Edrisi

LSU Doctoral Dissertations

The use of foams can be found abundantly in many applications in a wide range of industries, including oil and gas industry. Although understanding foam flow behavior is crucial for the optimization of such applications, the complex flow behavior of foams has been a major challenge. Recent experimental studies with surfactant foams presented a new way to characterize foam flow characteristics by using two flow regimes: the low-quality regime showing either plug-flow or segregated-flow pattern, and the high-quality regime showing slug-flow pattern. This study consists of three main components: (1) experimental investigation of foam rheology in pipes; (2) building up …

Evaluation Of Gas-Assisted Gravity Drainage Eor Process Applicability In A Louisiana Oil Field Through Experiments And Reservoir Simulation, Wagirin Ruiz Paidin

LSU Doctoral Dissertations

The Gas-Assisted Gravity Drainage (GAGD) process was developed as an alternative to conventional gas injection enhanced oil recovery (EOR) processes, which suffer from their inherent weakness of combating gravity segregation. The GAGD process, however, is aimed at taking advantage of this phenomenon and consists of using horizontal producers near the bottom of the payzone while injecting gas using vertical injection wells. It is hypothesized that the injected gas will rise to the top, thereby forming a gas cap while displacing reservoir brine/oil downward towards the producers. In this study, a single-well alternative to the multi-well GAGD process was investigated to …

Modeling Foam Delivery Mechanisms In Deep Vadose-Zone Remediation Using Method Of Characteristics (Moc), Alireza Roostapour

LSU Doctoral Dissertations

This study investigates foam delivery mechanisms in vadose-zone remediation by using Method of Characteristics (MoC). In such applications, dry foams are introduced into a porous medium which is initially at low saturation of water (Sw) containing pollutants such as metals and radionuclides. For vadose-zone remediation processes to be successful, the injected aqueous phase should carry chemicals to react with pollutants and precipitate them for immobilization and stabilization purposes. Typical remediation techniques such as water and surfactant injections are not applicable, because of the concerns about downward migration. As a result, understanding foam flow mechanism in-situ is key to the optimal …

An Experimental And Computational Investigation Of Rotating Flexible Shaft System Dynamics In Rotary Drilling Assemblies For Down Hole Drilling Vibration Mitigation, Richard Duff

LSU Doctoral Dissertations

Rotary drilling system vibration has long been associated with damaging the bit, the bottom hole assembly (BHA) and drill string. Vibration has been traditionally measured in the bottom hole assembly, and been closely associated with the resonant behaviors.

This research study proposes an improved physical laboratory model to explore the dynamic behaviors associated with vibration. This model includes contact with the borehole wall allowing a range of stabilization geometries while removing bit-formation interaction effects. The results of exercising the model help develop new insights into both vibration measurement diagnostics and mitigation strategy execution.

Presented here is a review of other …

Effect Of Surfactants And Brine Salinity And Composition On Spreading, Wettability And Flow Behavior In Gas-Condensate Reservoirs, Yu Zheng

LSU Doctoral Dissertations

The well-known condensate blockage problem causes severe impairment of gas productivity as the flowing bottom-hole pressure falls below the dew point in gas-condensate reservoirs. Hence, this study attempts to investigate the concept of modifying the spreading coefficient and wettability using low-cost surfactants in the near wellbore region, to prevent the gas flow problems associated with condensate buildup. This study also examines the effect of brine salinity and composition on wettability, spreading and adhesion in condensate buildup regions, to evaluate the ability of brine salinity/composition for enhanced gas productivity in gas-condensate reservoirs. In this study, experiments were performed at both ambient …

Strategies For Real Time Reservoir Management, Yuanyuan Shuai

LSU Doctoral Dissertations

Real–time reservoir management is developed to manage a shrinking labor force and rising demand on energy supply. This dissertation seeks good strategies for real–time reservoir management. First, two simulator–independent optimization algorithms are investigated: ensemble–based optimization (EnOpt) and bound optimization by quadratic approximation (BOBYQA). Multiscale regularization is applied to both to find appropriate frequencies for well control adjustment. Second, two gathered EnKF methods are proposed to save computational cost and reduce sampling error: gathered EnKF with a fixed gather size and adaptively gathered EnKF. Finally, oil price uncertainty is forecasted and quantified with three price forecasting models: conventional forecasting, bootstrap forecasting …

Numerical Study Of Downhole Heat Exchanger Concept In Geothermal Energy Extraction From Saturated And Fractured Reservoirs, Yin Feng

LSU Doctoral Dissertations

Geothermal energy has gained a lot of attention recently due to several favorable aspects such as ubiquitously distributed, renewable, low emission resources while leveraging the advances in the associated technologies such as directional drilling and low enthalpy power generation plant. However, there are still many challenges such as the high initial capital cost of drilling and surface facilities, environmental risk of seismicity due to the induced disequilibrium in the formation, and sustainability of project over designed operational life. Traditional downhole heat exchangers (DHE) could potentially reduce the capital cost and the risk of seismicity, but they are unable to maintain …

Analytical Design Method For Cold Production Of Heavy Oil With Bottom Water Using Bilateral Sink Wells, Wenting Qin

LSU Doctoral Dissertations

Few heavy oil reservoirs with strong bottom water drives have been developed successfully because of severe water coning. Water coning tends to cause low ultimate recovery, low well productivity, and high water production. Although thermal and gravity-assisted methods might improve recovery in oil reservoirs, such methods are widely perceived as either economically unfavorable or technologically infeasible. This study proposes a new, cold production technique, called Bilateral Water Sink (BWS), to meet those challenges. The BWS method suppresses water cresting by producing oil and water simultaneously from separate, horizontal wells completed in the oil and water zones; the oil and water …

Characterization Of Foam Flow In Pipes Using Two Flow Regime Concept, Rahul Narayanrao Gajbhiye

LSU Doctoral Dissertations

The objective of this study is to investigate the characteristics of foam flow behavior in pipes in a wide range of experimental conditions, including two pipe materials (stainless steel and nylon pipes with about 0.36 - 0.38 inch in inner diameter and 12 ft in length), three surfactant formulations (Cedepal FA-406, Stepanform-1050, and Aquet-944), and three surfactant concentrations (0.1, 0.5, and 5 wt%). The concept of “two foam-flow regimes”, consisting of high-quality regime and low-quality regime, is at the heart of interpreting the experimental data. The experimental results in horizontal pipes showed the presence of two distinct high-quality and low-quality …

Characterization Of Rock/Fluids Interactions At Reservoir Conditions, Dayanand Saini

LSU Doctoral Dissertations

In this study, interfacial phenomena of spreading, wettability, and rock/oil adhesion interactions in complex rock/oil/water systems were characterized at reservoir conditions of elevated pressures and temperatures. Capabilities of both ambient and reservoir condition optical cells were used for measuring the oil/water interfacial tension and dynamic (the water-receding and the water-advancing) contact angles for various complex rock/oil/water systems. Well known sessile oil drop volume alteration method was successfully used in this study for evaluating the applicability of the modified Young’s equation for characterizing the line tension in complex rock/oil/water systems at reservoir conditions. This appears to be first time when rock/fluids …

Progressive Water-Oil Transition Zone Due To Transverse Mixing Near Wells, Shengkai Duan

LSU Doctoral Dissertations

This study derives from observations made in petroleum research and practices of chemical industry that efficient mixing takes place in segregated immiscible fluid flow in granular packs and static mixers. A hypothesis was formulated that transverse mixing (TM) across oil-water interface may occur in segregated inflow to wells resulting in progressive transition zone, more water production, and reduced oil productivity. “Mixing” is broadly interpreted here to address the entire range of stirring, splitting, dispersion and diffusion processes between two fluids.

Initial study showed that a commercial reservoir simulator would not model any transition zone in segregated oil-water flow at high …

Continuous Reservoir Model Updating By Ensemble Kalman Filter On Grid Computing Architectures, Xin Li

LSU Doctoral Dissertations

A reservoir engineering Grid computing toolkit, ResGrid and its extensions, were developed and applied to designed reservoir simulation studies and continuous reservoir model updating. The toolkit provides reservoir engineers with high performance computing capacity to complete their projects without requiring them to delve into Grid resource heterogeneity, security certification, or network protocols.

Continuous and real-time reservoir model updating is an important component of closed-loop model-based reservoir management. The method must rapidly and continuously update reservoir models by assimilating production data, so that the performance predictions and the associated uncertainty are up-to-date for optimization. The ensemble Kalman filter (EnKF), a Bayesian …